涤纶薄膜拉伸过程中的电镜研究

<正> 聚对苯二甲酸乙二酯(PET)是用于纤维和薄膜的最重要的高分子材料之一。在拉伸过程中拉伸温度、拉伸比、应变速率等不同因素对PET的结晶、取向以及所形成的织态等的影响已有过广泛的研究。但用电镜直接观察PET薄膜在不同拉伸条件下的高分子聚集态结构的变化则报道很少。我们选择丙烯胺作刻蚀剂处理拉伸方式、拉伸温度、应变速率和拉伸比不同的PET试样,用扫描电镜直接观察其形态的变化。     

CRYSTALLIZATION AND MELTING OF NYLON 610

Differential scanning calorimetry was used to study the crystallization andmelting of nylon 610. For nylon 610 crystallized from the melt state (260℃), the overall rateof bulk crystallization can be described by a simple Avrami equation with Avrami exponentn ≈ 2, independent of crystallization temperature. With the experimentally obtainedT_m~0 (235℃ ～ 255℃) of nylon 610, the fold surface free energy σ_e was determined to be35 ～38 erg/cm~2. The effects of annealing temperature and time on the melting of quenchednylon 610 were also investigated. For nylon 610 quenched at room temperature there isonly one DSC endotherm peak DSC scans on annealed samples exhibited an endothermpeak at approximately 10℃ above the annealing temperature. The size and position of theendothermic peak is strongly related to annealing temperature and time. An additionalthird melting was observed when quenched nylon 610 was annealed at high temperaturefor a sufficiently long residence time. The existence of the third melting peak suggests thatmore than one kind of distribution of lamella thickness may occur when quenched nylon610 is annealed. The implications of these results in terms of crystal thickening mechanismwere discussed.     

不同结晶速率的PET薄膜在拉伸过程中的结晶与取向

用多种方法对两个结晶速率不同的PET样品在拉伸过程中的结晶和取向进行了研究。结果表明在同样的拉伸条件下,结晶速率较快的样品的结晶度和取向程度均比另一样品要高得多,这种结构变化上的差别说明把拉伸行为的差别归因于结晶速率的不同是合理的。     

A STUDY ON THE CRYSTALLIZATION KINETICS OF NYLON 1010

The kinetic behavior of isohermal and nonisothermal crystallization of nylon-1010has been studied by means of dilatometry and differential scanning calorimetry, respec-tively. The isothermal and nonisothermal process can be descibed by Avrami equationand Ozawa equation, respectively. From the experimental results the kinetic paramters ofcrystallization and crystalline mechanism for isothermal and nonisothermal measurementsare discussed.     

STUDIES ON THE ~(13)C-NMR SPECTRA OF ALTERNATING COPOLYMERS OF CONJUGATED DIENES WITH METHYL ACRYLATE

The ~(13)C-NMR spectra of alternating copolymers of conjugated dienes, butadiene (BD), isoprene(IP) and chloroprene (CP), with methyl acrylate (MA) were studied. It is proved that they are allalternating copolymers. The BD units in Poly (BD-alt-MA) are joined to MA mainly in the formof trans 1,4-structure. The contents of trans 1,4-, cis 1,4-and 1,2-structure are 88, 7 and 5%, res-pectively. The IP and CP units in Poly(IP-alt-MA) and Poly(CP-alt-MA) exist essentially as trans1,4-configuration and connect with MA units in "head to head" arrangement predominantly, whileCP-CP units present in Poly(CP-alt-MA) in a small quantity.     

STUDIES ON THE MECHANICAL PROPERTIES AND CRYSTALLIZATION BEHAVIOR OF POLYETHYLENE COMPOSITES

The effects of inter facial modifier on the mechanical, dynamic mechanical properties andcrystallization behavior of the polyethylene composites were investigated in the present paper.It was found that the interfacial modifer significantly improved the mechanical properties,influenced the dynamic mechanical spectra and slightly changed the crystallization behavior.The results showed that the interfacial modifier changed the dispersion state of dispersedphase of the composites, resulting in different phase structure, which was the major reasonIeading to different mechanical and crystallization properties.     

STRESS-INDUCED CRYSTALLIZATION OF POLYURETHANE/MONTMORILLONITE NANOCOMPOSITE

Exfoliated polyurethane/montmorillonite nanocomposites with both high elongation at break and high tensilestrength were studied by dynamic-infrared spectroscopy (dynamic-IR). The results show that crystallization induced byadditional stress is impeded by the nano-layered organo montmorillonite.     

MORPHOLOGICAL STUDIES OF A THERMOTROPIC SIDE-CHAIN LIQUID CRYSTALLINE POLYMER DURING MESOPHASE TRANSITIONS*

The morphological features of a side-chain liquid crystalline polymer during the mesophasetransitions were investigated by using the DSC technique. The polymer used was polyacrylate with mesogensof three benzene rings attached to the main chain through a flexible spacer. A special two-phase texture wasobserved in the transition temperature range. Similar to main-chain liquid crystalline polymers the transitionprocess of the side-chain liquid crystalline polymer was composed of an initiation of the new phase at localplaces of the old phase matrix and a growth process of the new phase domains.     

THE ORIENTATION AND CRYSTALLIZATION OF POLYETHYLENE TEREPHTHALATE

The drawing behavior of three types of PET spherulites and PET amorphous samples have beenstudied. Two different sample preparation techniques were used in this study: (1) The films withnormal positive, normal negative or abnormal spherulites were prepared by solution casting tech-niques, then the films were deformed by uniaxial drawing. The uniaxial drawing behavior of PETspherulites appears to be dependent on the angles between the c-axis and the radius direction of thespherulites and that the deformation of spherulites becomes more difficult the larger the angles. (2)Amorphous films of PET were prepared first, then the films were deformed under uniaxial drawingto achieve c-axis orientation at a temperature near the glass transition temperature. The orientedfilms were subsequently annealed with fixed length at 215℃The films prepared in this way ex-hibit excellent c-axis orientation along the stretching direction. The degree of perfection of thecrystalline structure is much greater than that of the spherulites.     

CRYSTALLIZATION KINETICS OF HOMOGENEOUS AND HETEROGENEOUS LLDPE

Based on thermal analysis, the isothermal and nonisothemal crystallization kinetics of Ziegler-Natta catalyzedlinear low density polyethylene (Z-N LLDPE) and metallocene catalyzed LLDPE (m-LLDPE) were studied. Treating theresults with the Avrami equation and the Ozawa equation, the crystallization constant lgk and the Avrami exponent n wereobtained. Some other crystallization parameters were also discussed. According to the different characteristics of the chainstructures of Z-N LLDPE and metallocene LLDPE, their crystallizaton behaviors were analyzed. It is indicated that thehomogeneity and heterogeneity of the two polymers act in different way during the crystallization process of polymers,including the nucleation and the growth of crystals under various conditions.     

STUDIES ON THE POLYMERIZATION OF β-CYCLODEXTRIN WITH EPICHLOROHYDRIN*

Different proportions of β-cydodextrin and epichlorohydrin were used to prepare a group of β-cyclodextrin polymers. The relationship between the reaction extent and the molar ratios of reactants was discussed according to the results of ~1H-NMR, ~(13) C-NMR spectra and elemental analysis. Especially, high resolution ~1H-NMR spectra were usd for studying the reaction active sites and the extent of reaction. The solubility of oil soluble drugs in water was largely improved in the presence of water-soluble β-cyclodextrin polymer.     

THEORETICAL ANALYSIS OF KINETICS OF NONISOTHERMAL CRYSTALLIZATION OF POLYMERS

The classical crystallization theories proposed by Avrami, Evans, and Mandelkern wereextended to the nonisothermal situation. The expressions derived from the classical equations canbe expressed in either the differential form or the integral form. A method was provided so as toobtain the parameters characterizing the crystallization rate and mechanism from DSC curves withseveral constant heating or cooling rates. The rate constants of crystallization obtained from bothisothermal and nonisothermal curves of poly(ethylene terephthalate)were compared.     

DILUTE SOLUTION BEHAVIOR OF CHITOSAN IN DIFFERENT ACID SOLVENTS

Dilute solution behavior of chitosan was studied in formic acid, acetic acid, lactic acid andhydrochloric acid aqueous solution under different pH values. The reduced viscosities, η_(sp)/C,ofchitosan solutions were dependent on the properties of acid and pH value of solvents. For a givenchitosan concentration, η~(sp)/C decreased with the increase of acid concentration, or decreasing pHof solvent, indicating shielding effect of excessive acid similar to adding salt into solution. Thestabilities of dilute chitosan solution in formic acid and lactic acid were better than that in acetic acid and hvdrochloric acid.     

VISCOELASTIC BEHAVIOR OF THE NON-HOOKE DEFORMATION BEFORE YIELDING IN UNIAXIAL DRAWING OF AMORPHOUS POLY(ETHYLENE TEREPHTHALATE)*

Viscoelastic behavior of the non-Hooke deformation of amorphous PET film before yield was investigated in thetemperature region 74--80.5℃ around the glass transition temperature. The film specimen was drawn to yield point followedby unloading to zero stress, then the residual deformation was held constant, while the subsequent evolution of the stress wasrecorded. An induction period was found in the course of stress evolution fol1owed by a stress step-increase. The inductionperiod decreases with increasing drawing temperature with an activation energy of 1.10 MJ/mol·K, which is attributed tothe time needed for the relaxation of rubbery deformation through cooperative internal rotations. At temperatures lower than74℃, there is no stress increase or the induction period becomes too long to be observed. Thus the nature of anelasticity inthe non-Hooke region before yielding is attributed to stress induced rubbery deformation. The experimental results areinterpreted in terms of Perez' rheological model of a series connected Hooke spring and a Voigt element consisting of aparallel connected elastic spring and a dashpot.     

MORPHOLOGICAL CHARACTERIZATION OF POLY (N-VINYLCARBAZOLE) OBTAINED WITH ASYMMETRICALLY STEREOSELECTIVE POLYMERIZATION*

The morphological characterizations of poly(N -vinylcarbazole)(PVCZ) obtained by asymmetricallystereoselective polymerization were studied using x-ray diffraction pattern, DSC and GPC. The results showthat the PVCZs have lower crystallinities (11.0～18.6%) and lower melting heats (2.2～7.5 J/g), but thedegree of crystallinities of the PVCZ samples obtained using the organic salts (acid) with chiral orstereodifferentiating ligands are higher than that using radical and general protonic initiator. It has shown thatthe crystallization is directly related to the packing density of the hexagonal array of the rodlike moleculesformed from the helical chain.     

STUDIES ON THE KINETICS OF PROPYLENE POLYMERIZATION WITH THE COMPLEXTYPE TiCl_3 CATALYST

The active center concentration C_p, the rate constant k_p, and the activation energy of chain propagation E_p in the polymerization of propylene with complex-type TiCl_3-(C_2H_5)_2AlCl catalyst system were studied. The Mn was corrected by (?) value determined by GPC. The values thus obtained for C_p, k_p, and E_p at 50℃were 3.01 mol/mol Ti, 6.27 1/mol·sec, and 5.10 Kcal/mol respectively.The kinetic parameters were compared with those obtained from conventional TiCl_3·AlCl_2 catalyst, showing that the higher activity of the complex-type catalyst over the conventional catalyst is not only due to the higher C_p of the former, but to a greater extent due to the increase of the k_p value.     

CRYSTALLIZATION BEHAVIOR OF A THERMOTROPIC LIQUID CRYSTAL COPOLYESTER

A thermotropic liquid crystal copolyester resin based on p-hydroxybenzoic acid, 2, 6-naphthoic acid, hydroxyquinone and PET was synthesized by melt condensation and studied. The results based on DSC and X-ray diffraction indicated that there were a rapid and a slow crystallization processes for the copolyester at certain conditions. A critical temperature was suggested, below which the slow crystallization could hardly happen. Above the critical temperature the extent of the slow crystallization process depended not only on annealing temperature but also on the annealing time. A fine crystal structure with high melting point and narrow diffraction peak was formed under favorable conditions.     

COMPUTER SIMULATION OF A SINGLE POLYMER CHAIN IN DIFFERENT SOLVENTS

In the present paper, the behavior of a single polymer chain under various solvent conditions was modeled by self-avoiding walks (SAW) with nearest neighbors attraction Δε on a simple cubic lattice. Determination of the θ-condition wasbased on the numerical results of the mean square radius of gyration and end-to-end distance. It was found that at the θtemperatue Δε/kT equals -0.27. The exponents a in the Mark-Houwink equation with different interaction parameters areconsistent with the results of experiments: under θ-condition, a = 0.5, and for a good solvent α= 0.74-0.84, respectively.     

PREPARATION AND PROPERTIES OF ETHYL-CYANOETHYL CELLULOSE/POLYACRYLIC ACID COMPOSITE FILMS WITH REFLECTION COLORS*

Ethyl-cyanoethyl cellulose [(E-CE)C]/acrylic acid (AA) becomes a cholesteric liquid crystalline solution withvivid colors when the (E-CE)C concentration is 42 wt%～52 wt%. (E-CE)C/polyacrylic acid (PAA) composites withcholesteric structure were prepared by polymerzing AA in (E-CE)C/AA liquid crystalline solutions. The layers of orderedpolymer chains in the cholesteric phase were inclined during polymerization and the degree of the inclination depended onthe polymerization temperature and the concentration of the solution before polymerization. The cholesteric structure in thecomposites could not be changed when temperature was lower than 100℃. Cross-linking of the PAA in compositesimproved their water-resistance. The cholesteric order of the composites without cross-linking was destroyed when theywhere immersed in water. The color derived from the selective reflection of the cholesteric phase of the cross-linkedcomposites turned from blue to red after the composites absorbed water. The color of the composites could be returned to theoriginal one when the absorbed water was removed from the swollen composites.     

CRYSTALLIZATION AND MECHANICAL PROPERTIES OF BLENDS OF METALLOCENE SHORT CHAIN BRANCHED POLYETHYLENE WITH CONVENTIONAL POLYOLEFINS

Metallocene-catalyzed short chain branched polyethylene (SCBPE) was blended with LDPE, HDPE, PS, EPDM and iPP in the weight proportions of 80 and 20. The crystallization and mechanical properties of these blends were studied by PLM, DSC and DMA. It has been observed in PLM that SCBPE/LDPE, SCBPE/HDPE and SCBPE/EPDM can form band spherulites whose band width and size are both smaller than that of the pure SCBPE. Tiny crystallites are observed in the completely immiscible SCBPE/PS blend. The crystallites in SCBPE/iPP are very small and only irregular spherulites are seen. The crystallization kinetics and mechanical properties of SCBPE are greatly affected by the second polyolefin, but in a different way, depending on the phase behavior and the modulus of the second components. SCBPE may be phase miscible in the melt with HDPE, LDPE and EPDM and co-crystallize together with HDPE or LDPE during cooling. A big change of crystal morphology and crystallization kinetics is seen in SCBPE/iPP blend compared with pure SCBPE and the lowest tanδ is also seen for this system. DMA results show that the tensile modulus of the blends has nothing to do with phase behavior, but only depends on the modulus of the second component.