Resonance in flow past oscillating cylinder under subcritical conditions

Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes and hydrodynamics forces on the cylinder surface are systematically investigated. Special attention is paid to the phenomenon of resonance induced by the cylinder oscillation. The results demonstrate that vortex shedding can be excited extensively under subcritical conditions, and the response region of vibration frequency broadens with increasing Reynolds number and oscillation amplitude. Two distinct types of vortex shedding regimes are observed. The first type of vortex shedding regime(VSR I) is excited at low frequencies close to the intrinsic frequency of flow, and the second type of vortex shedding regime(VSR II)occurs at high frequencies with the Reynolds number close to the critical value. In the VSR I, a pair of alternately rotating vortices are shed in the wake per oscillation cycle,and lock-in/synchronization occurs, while in the VSR II, two alternately rotating vortices are shed for several oscillation cycles, and the vortex shedding frequency is close to that of a stationary cylinder under the critical condition. The excitation mechanisms of the two types of vortex shedding modes are analyzed separately.     

Transition phenomena in the wake of an inclined square cylinder

The division of flow regimes in a square cylinder wake at various angles of attack (α) is studied. This study provides evidence of the existence of modes A and B instabilities in the wake of an inclined square cylinder. The critical Reynolds numbers for the inception of these instability modes were identified through the determination of discontinuities in the Strouhal number versus Reynolds number curves. The spectra and time traces of wake streamwise velocity were observed to display three distinct patterns in different flow regimes. Streamwise vortices with different wavelengths at various Reynolds numbers were visualized. A PIV technique was employed to quantitatively measure the parameters of wake vortices. The wavelengths of the streamwise vortices in the modes A and B regimes were measured by using the auto-correlation method. From the present investigation, the square cylinder wake at various angles of attack undergoes a similar transition path to that of a circular cylinder, although various quantitative parameters measured which include the critical Reynolds numbers, spanwise wavelength of secondary vortices, and the circulation and vorticity of wake vortices all show an α dependence.     

Combined action of transverse oscillations and uniform cross-flow on vortex formation and pattern of a circular cylinder

This paper attempts to study the roles of lateral cylinder oscillations and a uniform cross-flow in the vortex formation and wake modes of an oscillating circular cylinder. A circular cylinder is given lateral oscillations of varying amplitudes (between 0.28 and 1.42 cylinder-diameters) in a slow uniform flow stream (Reynolds number=284) to produce the 2S, 2P and P+S wake modes. Detailed flow information is obtained with time-resolved particle-image velocimetry and the phase-locked averaging techniques. In the 2S and 2P mode, the flow speeds relative to the cylinder movement are less than the uniform flow velocity and it is found that initial formation of a vortex is caused by shear-layer separation of the uniform flow on the cylinder. Subsequent development of the shear-layer vortices is affected by the lateral cylinder movement. At small cylinder oscillation amplitudes, vortices are shed in synchronization with the cylinder movement, resulting in the 2S mode. The 2P mode occurs at larger cylinder oscillation amplitudes at which each shear-layer vortex is found to undergo intense stretching and eventual bifurcation into two separate vortices. The P+S mode occurs when the cylinder moving speeds are, for most of the time, higher than the speed of the uniform flow. These situations are found at fast and large-amplitude cylinder oscillations in which the flow relative to the cylinder movement takes over the uniform flow in governing the initial vortex formation. The formation stages of vortices from the cylinder are found to bear close resemblance to those of a vortex street pattern of a cylinder oscillating in an otherwise quiescent fluid at Keulegan–Carpenter numbers around 16. Vortices in the inclined vortex street pattern so formed are then convected downstream by the uniform flow as the vortex pairs in the 2P mode.     

Symmetric vortex shedding in the near wake of a circular cylinder due to streamwise perturbations

Symmetric perturbations imposed on cylinder wakes may result in a modification of the vortex shedding mode from its natural antisymmetric, or alternating, to a symmetric one where twin vortices are simultaneously shed from both sides of the cylinder. In this paper, the symmetric mode in the wake of a circular cylinder is induced by periodic perturbations imposed on the in-flow velocity. The wake field is examined by PIV and LDV for Reynolds numbers about 1200 and for a range of perturbation frequencies between three and four times the natural shedding frequency of the unperturbed wake. In this range, a strong competition between symmetric and antisymmetric vortex shedding occurs for the perturbation amplitudes employed. The results show that symmetric formation of twin vortices occurs close to the cylinder synchronized with the oscillatory component of the flow. The symmetric mode rapidly breaks down and gives rise to an antisymmetric arrangement of vortex structures further downstream. The downstream wake may or may not be phase-locked to the imposed oscillation. The number of cycles for which the symmetric vortices persist in the near wake is a probabilistic function of the perturbation frequency and amplitude. Finally, it is shown that symmetric shedding is associated with positive energy transfer from the fluid to the cylinder due to the fluctuating drag.     

Hydrodynamic instability of separated viscous flow around a circular cylinder

A uniform viscous flow around a circular cylinder is studied numerically in the Reynolds number range from 0 to 500. It is shown that the existence and the basic properties of self-oscillating regimes are specified by the evolution of their hydrodynamic instability. It is found that the vortex formation in a near wake is associated with the separation zone dynamics in the main flow. The values of critical Reynolds numbers for the four successive bifurcations of the self-oscillating regimes of flow are obtained. An interpretation of experimental data on the vortices in the near wake is discussed.     

Separated flow structures around a cylindrical obstacle in a narrow channel

A detailed experimental study is performed on the separated flow structures around a low aspect-ratio circular cylinder (pin-fin) in a practical configuration of liquid cooling channel. Distinctive features of the present arrangement are the confinement of the cylinder at both ends, water flow at low Reynolds numbers (Re = 800, 1800, 2800), very high core flow turbulence and undeveloped boundary layers at the position of the obstacle. The horseshoe vortex system at the junctions between the cylinder and the confining walls and the near wake region behind the obstacle are deeply investigated by means of Particle Image Velocimetry (PIV). Upstream of the cylinder, the horseshoe vortex system turns out to be perturbed by vorticity bursts from the incoming boundary layers, leading to aperiodical vortex oscillations at Re = 800 or to break-away and secondary vorticity eruptions at the higher Reynolds numbers. The flow structures in the near wake show a complex three-dimensional behaviour associated with a peculiar mechanism of spanwise mass transport. High levels of free-stream turbulence trigger an early instabilization of the shear layers and strong Bloor–Gerrard vortices are observed even at Re = 800. Coalescence of these vortices and intense spanwise flow inhibit the alternate primary vortex shedding for time periods whose length and frequency increase as the Reynolds number is reduced. The inhibition of alternate vortex shedding for long time periods is finally related to the very large wake characteristic lengths and to the low velocity fluctuations observed especially at the lowest Reynolds number.     

Numerical simulation of the turbulent wake behind a normal flat plate

The three-dimensional wake flow behind a flat plate placed normal to the free stream has been investigated by means of direct numerical simulations. The Reynolds number Re based on the homogeneous inflow velocity and the uniform width d of the plate was 750. Coherent vortices were alternately shed from the sides of the plate with a frequency corresponding to a Strouhal number 0.168. The wake was distinctly turbulent downstream of the plate whereas the mean recirculation bubble extended 1.96d downstream. A steady 2D mean flow and the accompanying Reynolds stresses were obtained by averaging in time and along the span of the plate. These Reynolds-averaged statistics exhibited the same qualitative features as corresponding data from cylinder wakes.     

Vortex shedding and three-dimensional behaviour of flow past a cylinder confined in a channel

A numerical investigation of the flow past a circular cylinder centred in a two-dimensional channel of varying width is presented. For low Reynolds numbers, the flow is steady. For higher Reynolds numbers, vortices begin to shed periodically from the cylinder. In general, the Strouhal frequency of the shedding vortices increases with blockage ratio. In addition, a two-dimensional instability of the periodic vortex shedding is found, both empirically and by means of a Floquet stability analysis. The instability leads to a beating behaviour in the lift and drag coefficients of the cylinder, which occurs at a Reynolds number higher than the critical Reynolds number for the three-dimensional mode A-type instability, but lower than a Reynolds number for any mode B-type instability.     

An experimental investigation of flow past a dual step cylinder

Flow development in the wake of a dual step cylinder has been investigated experimentally using Laser Doppler Velocimetry and flow visualization. The dual step cylinder model is comprised of a large diameter cylinder (D) mounted at the mid-span of a small diameter cylinder (d). The experiments have been performed for a Reynolds number (Re _D ) of 1,050, a diameter ratio (D/d) of 2, and a range of large cylinder aspect ratios (L/D). The results show that the flow development is highly dependent on L/D. The following four distinct flow regimes can be identified based on vortex dynamics in the wake of the large cylinder: (1) for L/D ≥ 15, three vortex shedding cells form in the wake of the large cylinder, one central cell bounded by two cells of lower frequency, (2) for 8 < L/D ≤ 14, a single vortex shedding cell forms in the wake of the large cylinder, (3) for 2 < L/D ≤ 6, vortex shedding from the large cylinder is highly three-dimensional. When spanwise vortices are shed, they deform substantially and attain a hairpin shape in the near wake, (4) for 0.2 ≤ L/D ≤ 1, the large cylinder induces vortex dislocations between small cylinder vortices. The results show that for Regimes I to III, on the average, the frequency of vortex shedding in the large cylinder wake decreases with L/D, which is accompanied by a decrease in coherence of the shed vortices. In Regime IV, small cylinder vortices connect across the large cylinder wake, but these connections are interrupted by vortex dislocations. With decreasing L/D, the frequency of dislocations decreases and the dominant frequency in the large cylinder wake increases toward the small cylinder shedding frequency.     

Three-dimensional numerical simulation of the wake flow of an afterbody at subsonic speeds

We numerically investigate the wake flow of an afterbody at low Reynolds number in the incompressible and compressible regimes. We found that, with increasing Reynolds number, the initially stable and axisymmetric base flow undergoes a first stationary bifurcation which breaks the axisymmetry and develops two parallel steady counter-rotating vortices. The critical Reynolds number (Re _cs) for the loss of the flow axisymmetry reported here is in excellent agreement with previous axisymmetric BiGlobal linear stability (BiGLS) results. As the Reynolds number increases above a second threshold, Re _co, we report a second instability defined as a three-dimensional peristaltic oscillation which modulates the vortices, similar to the sphere wake, sharing many points in common with long-wavelength symmetric Crow instability. Both the critical Reynolds number for the onset of oscillation, Re _co, and the Strouhal number of the time-periodic limit cycle, St_sat, are substantially shifted with respect to previous axisymmetric BiGLS predictions neglecting the first bifurcation. For slightly larger Reynolds numbers, the wake oscillations are stronger and vortices are shed close to the afterbody base. In the compressible regime, no fundamental changes are observed in the bifurcation process. It is shown that the steady state planar-symmetric solution is almost equal to the incompressible case and that the break of planar symmetry in the vortex shedding regime is retarded due to compressibility effects. Finally, we report the developments of a low frequency which depends on the afterbody aspect ratio, as well as on the Reynolds and on the Mach number, prior to the loss of the planar symmetry of the wake.     

TR-PIV measurement of the wake behind a grooved cylinder at low Reynolds number

A comparative study of the wakes behind cylinders with grooved and smooth surfaces was performed with a view to understand the wake characteristics associated with the adult Saguaro cacti. A low-speed recirculation water channel was established for the experiment; the Reynolds number, based on the free-stream velocity and cylinder diameter (D), was kept at Re_D=1500. State-of-the-art time-resolved particle image velocimetry (TR-PIV) was employed to measure a total of 20 480 realizations of the wake field at a frame rate of 250 Hz, enabling a comprehensive view of the time- and phase-averaged wake pattern. In comparison to the wake behind the smooth cylinder, the length of the recirculation zone behind the grooved cylinder was extended by nearly 18.2%, yet the longitudinal velocity fluctuation intensity was considerably weakened. A global view of the peaked spectrum of the longitudinal velocity component revealed that the intermediate region for the grooved cylinder, which approximately corresponds to the transition region where the shear layer vortices interact, merge and shed before the formation of the Karman-like vortex street, was much wider than that for the smooth one. The unsteady events near St=0.3-0.4 were detected in the intermediate region behind the grooved cylinder, but no such events were found in the smooth cylinder system. Although the formation of the Karman-like vortex street was delayed by about 0.6D downstream for the grooved cylinder, no prominent difference in the vortex street region was found in the far wake for both cylinders. The Proper Orthogonal Decomposition (POD) method was used extensively to decompose the vector and swirling strength fields, which gave a close-up view of the vortices in the near wake. The first two POD modes of the swirling strength clarified the spatio-temporal characteristics of the shear layer vortices behind the grooved cylinder. The small-scale vortices superimposed on the shear layers behind the grooved cylinder were found to be generated and convected downstream in the same phase, which would significantly reduce the fluctuating force on the cylinder surface.     

A FLOW VISUALIZATION STUDY ON FEEDBACK CONTROL OF VORTEX SHEDDING FROM A CIRCULAR CYLINDER

This note presents flow visualization results to show the response of wake flows behind a cylinder to the feedback suppression and excitation. The experiments were conducted in a water channel and the feedback perturbations were introduced into the wake by oscillating the cylinder transverse to the oncoming flow. The visualization photographs directly illustrated the wake flows under the feedback suppression and excitation at Reynolds numbers up to 25% above the natural onset Reynolds number for vortex shedding.     

Momentum and heat transport in a finite-length cylinder wake

This paper reports an experimental study of turbulent momentum and heat transport in the wake of a wall-mounted finite-length square cylinder, with its length-to-width ratio L/d = 3–7. The cylinder was slightly heated so that heat produced could be considered as a passive scalar. A moveable three-wire probe (a combination of an X-wire and a cold wire) was used to measure velocity and temperature fluctuations at a Reynolds number of 7,300 based on d and the free-stream velocity. Measurements were performed at 10 and 20d downstream of the cylinder at various spanwise locations. Results indicate that L/d has a pronounced effect on Reynolds stresses, temperature variance and heat fluxes. The downwash flow from the free end of the cylinder acts to suppress spanwise vortices and, along with the upwash flow from the cylinder base, makes the finite-length cylinder wake highly three-dimensional. Reynolds stresses, especially the lateral normal stress, are significantly reduced as a result of suppressed spanwise vortices at a small L/d. The downwash flow acts to separate the two rows of spanwise vortices further apart from the wake centerline, resulting in a twin-peak distribution in temperature variance. While the downwash flow entrains high-speed fluid into the wake, responsible for a small deficit in the time-averaged streamwise velocity near the free end, it does not alter appreciably the distribution of time-averaged temperature. It has been found that the downwash flow gives rise to a counter-gradient transport of momentum about the central region of the wake near the free end of the cylinder, though such a counter-gradient transport does not occur for heat transport.     

Phenomenology of Kármán vortex streets in oscillatory flow

Vortex wakes of circular cylinders at low Reynolds numbers have been investigated. Sound waves are superimposed on the flow in mean flow direction. In this configuration the Kármán vortices are shed at the sound frequency or at subharmonics of the sound frequency. The Karman vortex street is treated as a nonlinear self-excited flow oscillator with forced oscillations. Using a flow visualization technique a variety of wake structures has been identified as a function of sound frequency and sound amplitude, but independent of the Reynolds number. The superimposed sound influences the distribution of circulation and accordingly the shedding mechanism. Primary vortex and secondary vortex are shed simultaneously from one side of the cylinder. The alternate vortex shedding is arranged spatially and temporally. Structures along the vortex axes are revealed.Parts of this paper have been presented at IUTAM Congress 1984, Lyngby, Denmark, and at ICNM Conference 1985, Shanghai, P. R. China     

The near wake structure of a square cylinder

The near wake structure of a square cross section cylinder in flow perpendicular to its length was investigated experimentally over a Reynolds number (based on cylinder width) range of 6700–43,000. The wake structure and the characteristics of the instability wave, scaling on θ at separation, were strongly dependent on the incidence angle () of the freestream velocity. The nondimensional frequency (St_θ) of the instability wave varied within the range predicted for laminar instability frequencies for flat plate wakes, jets and shear layers. For = 22.5°, the freestream velocity was accelerated over the side walls and the deflection of the streamlines (from both sides of the cylinder) towards the center line was higher compared to the streamlines for = 0°. This caused the vortices from both sides of the cylinder to merge by x/d 2, giving the mean velocity distribution typical of a wake profile. For = 0°, the vortices shed from both sides of the cylinder did not merge until x/d 4.5. The separation boundary layer for all cases was either transitional or turbulent, yet the results showed good qualitative, and for some cases even quantitative, agreement with linearized stability results for small amplitude disturbances waves in laminar separation layers.     

Asymmetric vortex shedding flow past an inclined flat plate at high incidence

This paper reports an experimental investigation of the vortex shedding wake behind a long flat plate inclined at a small angle of attack to a main flow stream. Detailed velocity fields are obtained with particle-image velocimetry (PIV) at successive phases in a vortex shedding cycle at three angles of attack, α=20°, 25° and 30°, at a Reynolds number Re≈5,300. Coherent patterns and dynamics of the vortices in the wake are revealed by the phase-averaged PIV vectors and derived turbulent properties. A vortex street pattern comprising a train of leading edge vortices alternating with a train of trailing edge vortices is found in the wake. The trailing edge vortex is shed directly from the sharp trailing edge while there are evidences that the formation and shedding of the leading edge vortex involve a more complicated mechanism. The leading edge vortex seems to be shed into the wake from an axial location near the trailing edge. After shedding, the vortices are convected downstream in the wake with a convection speed roughly equal to 0.8 the free-stream velocity. On reaching the same axial location, the trailing edge vortex, as compared to the leading edge vortex, is found to possess a higher peak vorticity level at its centre and induce more intense fluid circulation and Reynolds stresses production around it. It is found that the results at the three angles of attack can be collapsed into similar trends by using the projected plate width as the characteristic length of the flow.     

On the flow behaviour of confined finite-length wavy cylinders

Confined aspect-ratio of 6 wavy cylinders with a mean blockage-ratio of 0.5 were studied using time-resolved particle-image velocimetry at a sub-critical Reynolds number of 2700. Wavelengths and wave amplitudes of 2–4 and 0.1–0.3 mean diameters respectively were investigated. Results show that vortices are generally shed from the wavy cylinder and channel walls regularly, reminiscent of the unsteady symmetric flow configuration in confined non-wavy cylinders. Furthermore, vortex formation lengths for confined wavy cylinders are generally shorter than their unconfined counterparts, though their variations with respect to geometrical changes remain consistent with unconfined flow conditions. Gross cross-stream flow behaviour does not differ significantly between confined and unconfined wavy cylinders, indicating that finite-length effects are independent of the present confinement. Confined wavy cylinder wake regions are more sensitive towards geometrical changes and a combination of small wavelength and large wave amplitude leads to significant suppression of coherent cylinder and wall vortex-shedding. This is supported by phase-averaged flow reconstructions derived from Proper Orthogonal Decomposition analysis. Lastly, larger wave amplitudes lead to redistributions of dominant flow energy further downstream and to higher mode numbers, which suggests a causal link to the formation of stronger and more coherent streamwise vortices.     

Near-wake flow characteristics of a circular cylinder close to a wall

Flow characteristics in the near wake of a circular cylinder located close to a fully developed turbulent boundary layer are investigated experimentally using particle image velocimetry (PIV). The Reynolds number based on the cylinder diameter (D) is 1.2×10⁴ and the incident boundary layer thickness (δ) is 0.4D. Detailed velocity and vorticity fields in the wake region (0<x/D<6) are given for various gap heights (S) between the cylinder and the wall, with S/D ranging from 0.1 to 1.0. Both the ensemble-averaged (including the mean velocity vectors and Reynolds stress) and the instantaneous flow fields are strongly dependent on S/D. Results reveal that for S/D⩾0.3, the flow is characterized by the periodic, Kármán-like vortex shedding from the upper and lower sides of the cylinder. The shed vortices and their evolution are revealed by analyzing the instantaneous flow fields using various vortex identification methods, including Galilean decomposition of velocity vectors, calculation of vorticity and swirling strength. For small and intermediate gap ratios (S/D⩽0.6), the wake flow develops a distinct asymmetry about the cylinder centreline; however, some flow quantities, such as the Strouhal number and the convection velocity of the shed vortex, keep roughly constant and virtually independent of S/D.     

Aerodynamic forces and three-dimensional flow structures in the mean wake of a surface-mounted finite-height square prism

Different flow models have been proposed for the flow around surface-mounted finite-height square prisms, but there is still a lack of consensus about the origin and connection of the streamwise tip vortices with the other elements of the wake. This numerical study was performed to address this gap, in addition to clarifying the relationship of the near-wake structures with the far wake and the near-wall flow, which is associated with the fluid forces. A large-eddy simulation approach was adopted to solve the flow around a surface-mounted finite-height square prism with an aspect ratio of AR = 3 and a Reynolds number Re = 500. The mean drag and normal forces and the bending moment for the prism were quantitatively compared in terms of skin-friction and pressure contributions, and related to the near-wall flow. Both three-dimensional visualizations and planar projections of the time-averaged flow field were used to identify, qualitatively, the main structures of the wake, including the horseshoe vortex, corner vortices and regions of high streamwise vorticity in the upper part of the wake. These features showed the same qualitative behavior as reported in high Reynolds number studies. It was found that some regions of high streamwise vorticity magnitude, like the tip vortices, are associated with the three-dimensional bending of the flow, and the tip vortices did not continuously extend to the free end of the prism. The three-dimensional flow analysis, which integrated different observations of the flow field around surface-mounted finite-height square prisms, also revealed that the mean near-wake structure is composed of two sections of different origin and location of dominance.     

Developing and fully developed turbulent flow in ribbed channels

Wall-mounted roughness features, such as ribs, are often placed along the walls of a channel to increase the convective surface area and to augment heat transfer and mixing by increasing turbulence. Depending on the relative roughness size and orientation, the ribs also have varying degrees of increased pressure losses. Designs that use ribs to promote heat transfer encompass the full range of having only a few streamwise ribs, which do not allow fully developed flow conditions, to multiple streamwise ribs, which do allow the flow to become fully developed. The majority of previous studies have focused on perturbing the geometry of the rib with little attention to the spatially and temporally varying flow characteristics and their dependence on the Reynolds number. A staggered rib-roughened channel study was performed using time-resolved digital particle image velocimetry (TRDPIV). Both the developing (entry region) and a fully developed region were interrogated for three Reynolds numbers of 2,500, 10,000, and 20,000. The results indicate that the flow was more sensitive to Reynolds number at the inlet than within the fully developed region. Despite having a similar mean-averaged flowfield structure over the full Reynolds number range investigated, the population and distribution of coherent structures and turbulent dissipation within the fully developed region were also found to be Reynolds number dependent. Exploring the time-accurate flow characteristics revealed that in addition to vortices shed from the rib shear layer, the region of the rib wake was governed by a periodic process of bursting of the wake vortices resulting in the intermittent ejection of the inter-rib recirculation region into the core flow. This periodic process was the driving mechanism resulting in mixing and heat transfer augmentation. A quadrant-splitting burst analysis was also performed to determine the characteristic frequency and duration of inter-rib bursting as well as the wake shedding frequency, both of which were determined to be Reynolds number dependent.