Determination of ortho-cresyl phosphate isomers of tricresyl phosphate used in aircraft turbine engine oils by gas chromatography and mass spectrometry

Tricresyl phosphate (TCP) is used as an anti-wear additive in aircraft turbine engine oil. Concerns about its toxicity are largely based on the tri-o-cresyl phosphate isomer content. However, the presence of other and more toxic isomers has been previously suggested. In this work, the structural isomers of TCP have been determined by two methods (experimental and semi-theoretical). First, the TCP isomers were separated by gas chromatography (GC) and identified by mass spectrometry (MS). Second, after base cleavage of TCP, GC was used to quantify the cresol precursors. These results were used to calculate the TCP isomer distribution based on the assumption of a statistical distribution of the TCP isomers. The results from the two determinations showed reasonable agreement for three of the four oils studied. The o-cresyl isomers were found to be present almost exclusively as the more toxic mono-o-cresyl isomers in the concentration range 13-150 mg/L. The ability to analyse for the mono-o-cresyl isomers allows the toxicity of TCP to be based on the latter isomers rather than on the less toxic tri-o-cresyl phosphate isomer.     

Spectroscopic Characterization of the Geminal Isomer of Lewisite

Abstract

Lewisite is generally a mixture of several components with the trans isomer of lewisite being the predominant compound. A geminal isomer has not been previously reported as one of the components of the mixture. In the lewisite samples we examined, the geminal isomer, dichloro(l-chlorovinyl)arsine, comprised 2.7 per cent of the total material compared to 95.2 and less than 1 per cent, respectively, for the trans and cis isomers. The remaining fraction was not identified. The geminal isomer of lewisite has been characterized along with the trans and cis isomers using several spectroscopic techniques. Proton NMR of the geminal isomer produced a coupling constant consistent with vinylic protons in a geminal configuration. Mass spectrometry and infrared spectroscopy characterizations were based on an ethanedithiol derivative of the lewisite isomers with gas chromatography used to first separate the derivatized isomers. The electron ionization massspectra of the trans and cis derivatives were very similar, but significant differences were observed in the mass spectrum of the geminal form. Infrared absorption spectra were obtained for the trans and geminal derivatives with significant differences observed between the two, but the method was not sensitive enough to detect the cis isomer.

     

Analysis and deconvolution of dimethylnaphthalene isomers using gas chromatography vacuum ultraviolet spectroscopy and theoretical computations

An issue with most gas chromatographic detectors is their inability to deconvolve coeluting isomers. Dimethylnaphthalenes are a class of compounds that can be particularly difficult to speciate by gas chromatography – mass spectrometry analysis, because of their significant coelution and similar mass spectra. As an alternative, a vacuum ultraviolet spectroscopic detector paired with gas chromatography was used to study the systematic deconvolution of mixtures of coeluting isomers of dimethylnaphthalenes. Various ratio combinations of 75:25; 50:50; 25:75; 20:80; 10:90; 5:95; and 1:99 were prepared to test the accuracy, precision, and sensitivity of the detector for distinguishing overlapping isomers that had distinct, but very similar absorption spectra. It was found that, under reasonable injection conditions, all of the pairwise overlapping isomers tested could be deconvoluted up to nearly two orders of magnitude (up to 99:1) in relative abundance. These experimental deconvolution values were in agreement with theoretical covariance calculations performed for two of the dimethylnaphthalene isomers. Covariance calculations estimated high picogram detection limits for a minor isomer coeluting with low to mid-nanogram quantity of a more abundant isomer. Further characterization of the analytes was performed using density functional theory computations to compare theory with experimental measurements. Additionally, gas chromatography – vacuum ultraviolet spectroscopy was shown to be able to speciate dimethylnaphthalenes in jet and diesel fuel samples.     

Analysis of soman and sarin in blood utilizing a sensitive gas chromatography-mass spectrometry method

Gas chromatography with electron impact mass spectrometry and selected ion monitoring provided a simple and sensitive method for measuring organophosphorus compounds sarin and the two isomers of soman (isomer I and isomer II) in blood. These compounds were extracted from blood or isotonic saline using a modification of the method developed by Sass et al. Blood was deproteinized with perchloric acid before extraction. The acid-induced degradation of the organophosphorus compounds could be minimized by neutralizing the acid immediately after deproteinizing. In saline and blood, 81% of the extractable soman and 74% of the extractable sarin was recovered with a single extraction. The overall recovery of added organophosphorus was less in blood than in saline because of the binding of organophosphorus to blood constituents, probably various enzymes and proteins. A time-dependent decrease in extractable organophosphorus was found in whole blood but not in saline. Although soman isomer II was degraded in blood faster than soman isomer I, no significant difference in the affinities of these two isomers to acetylcholinesterase was observed.     

The routine analysis of some specific isomers of polychlorinated biphenyl congeners in human milk

A mixture of 14 polychlorinated biphenyl (PCB) isomers of various congeners, representing approximately 70% of all human milk PCBs reported in the literature, was made up to identify and approximate their residues in human milk. Individual isomer levels varied from 5 to 103 nanograms per gram of milkfat with the 2,2',4,4',5,5'-hexachlorobiphenyl isomer as the major PCB contaminant of human milk. PCB isomer numbers 74, 118, 153, 138 and 180 made up approximately 75% of all PCBs as measured by this mixture. There was close agreement of total PCB isomer content in breast milk between electron capture gas chromatography and gas chromatographic mass spectrometry determinations. A major interference was encountered however for PCB isomer no. 52, whose residue level in the breast milk was approximately 3 X higher by gas liquid chromatography than by mass spectrometry.     

Alkane isomers: presence in petroleum ether and complexity

The presence and absence of alkane isomers in petroleum and petroleum derivatives depend on the complexity of these structures. It was assumed that the more complex the structure is the less probable it is that that the molecule can be detected in any petroleum derivative. Complexity is a vague concept, which has not been defined in quantitative terms yet, and therefore there is no experimental method, which could be used to determine 'complexity'. Mass spectrometry and infrared spectroscopy in combination with gas chromatography were used to identify the various structural isomers of alkanes in petroleum ether. The isomers were categorised in quantitative terms by using topological indices and linear discriminant analysis. It was found that alkanes possessing a more complex, highly branched structure are less probable to be detected in petroleum ether than isomers with a simpler backbone structure. It was proposed that the experimental 'measure' of the complexity of isomer(i) should be proportional to 1/C(i), where C(i), denotes the concentration of isomer(i) in a (primary) petroleum derivative.     

Characterisation of sorbate geometrical isomers

trans,trans Isomers of sorbic acid, its potassium salt and ethyl sorbate isomerise under UV irradiation. All four geometrical isomers of the acid, salt and ester were separated using high-performance liquid chromatography on a nonpolar reversed-phase column (C18) and the ester also by gas chromatography on a VOCOL capillary column. The limit of detection and the interval of linearity were determined for all chromatographic methods. Individual isomers were identified with NMR analysis. Resolved chemical shifts of protons adjacent to the double bonds enabled qualitative and quantitative determination of isomers in the mixture. Antimicrobial activity of potassium sorbate isomers was tested on yeast Saccharomyces cerevisiae. Results show that the pure trans,trans isomer has a higher antimicrobial activity than the mixture of isomers.     

溶胶-凝胶法制备高热稳定性的毛细管气相色谱柱

毛细管气相色谱柱的传统制备工艺都较为复杂,周期较长,同时固定相和石英毛细管内壁间通常并无化学键生成,在较高温度下使用时固定相的流失严重,导致这类色谱柱的最高允许使用温度不很高．溶胶-凝胶法是一种快速有效的制备色谱柱的新技术,近年来经常应用于高效液相色谱、毛细管电色谱和固定相微萃取等分析化学的许多领域．在气相色谱方面,溶胶-凝胶端羟基聚硅氧烷柱、溶胶-凝胶聚乙二醇柱和溶胶-凝胶开链冠醚柱已相继制备出来,在用溶胶-凝胶     

Impact of average free‐volume element size on transport in stereoisomers of polynorbornene. II. Impact of temperature on solubility

This article evaluates the influence of temperature on the sorption of gases in two isomers of polynorbornene. The subject polymers were stereoisomers with nearly identical bulk density and total free volume. Because of differences in the mobility of the polymer backbone, the isomers packed differently resulting in differences in the average free‐volume element size within the matrix. The influence of these differences on free‐volume element size was characterized by the heat of sorption of gases in the matrix. The most pronounced differences were observed in the isosteric heats of sorption of condensable carbon dioxide and methane in the polymer isomers. This analysis suggests that the relative space available for sorption into free‐volume elements is higher in the methyl II isomer relative to methyl III. These conclusions support the physical characterizations reported in Part I of this series suggesting that the methyl II isomer has larger average free‐volume elements but fewer of them than the methyl III isomer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1939–1946, 2003     

Aromatic polyamides. II. Thermal degradation of some aromatic polyamides and their model diamides

Thermal degradation behavior of poly(1,3-phenylene isophthalamide) and poly(chloro-2,4-phenylene isophthalamide) was investigated with the aid of some appropriate model compounds. The pyrolysis products of these materials were identified by gas chromatography (GC), gas chromatography/Fourier transform infrared spectroscopy (GC/FT-IR), and gas chromatography/mass spectrometry (GC/MS). The residual chars were characterized by IR spectroscopy. Thermogravimetric analysis (TGA) was applied to study the effect of end-group concentration on the degradation characteristics of the two polyamides. Kinetic parameters that describe the thermal degradation of the polyamides were also evaluated by TGA. The results of this investigation suggest that the thermal decomposition of these aromatic polyamides involves homolytic as well as hydrolytic cleavages of the amide units.     

Determinations of polychlorinated biphenyl isomers by response factor calibration

Quantitative measurement of polychlorinated biphenyl (PCB) isomers by response factor calibration (RFC) is evaluated with gas chromatography and the Hall electrolytic conductivity detector. The procedure requires neither isomer identification nor reference compounds identical to each measured PCB isomer. Weight percent chlorine is determined for five Aroclor mixtures by RFC and compared within a few percent of expected values. Individual PCB isomers are measured and quantitatively compared for Aroclor mixtures. Also, RFC determinations for ten PCB isomers contained in a test material reference solution are compared to the supplier's stated concentrations. These RFC measurements provide quantitative analyses in the absence of a standard for each measured component.     

Quinidine oxidative metabolism. Identification and biosynthesis of quinidine 10,11-dihydrodiol stereoisomers

The isocratic reversed phase high performance liquid chromatographic method proposed for quinidine metabolic studies facilitates particularly the separation of 10(R) and (S) isomers of quinidine 10,11-dihydrodiols. The finding of each of these forms following a new synthetic pathway allows us to identify and quantify them in biological fluids. These two isomers have especially been observed in rat bile and hepatocyte secretions. The metabolic inducing effect of phenobarbital on the oxidative metabolism of quinidine is verified in rat isolated hepatocytes. Simultaneous secretion of the two dihydrodiols is also verified in human urine by a gas chromatography/mass spectrometry procedure.     

Different responses of E:Z‐isomers of pesticides in liquid chromatography–electrospray ionization–mass spectrometry

The mass spectrometric behavior of four pairs of stereoisomers was investigated by liquid chromatography–electrospray ionization–mass spectrometry (LC–ESI–MS). The E‐ and Z‐isomers of the pesticides chlorfenvinphos, dimethomorph, mevinphos and phosphamidon—each with one double bond—were chosen for this study. The MS response of the individual isomers was investigated by infusing the isomers individually into the MS or after the separation of isomer mixtures via high‐performance liquid chromatography(HPLC). In the case of dimethomorph, the same MS response was found for the two isomers. In contrast to that, the individual isomers of chlorfenvinphos, mevinphos and phosphamidon showed different MS response both in the single ion monitoring (SIM) mode in single quadrupole MS and multiple reaction monitoring (MRM) mode in tandem MS. The MS response of the isomers partly depends on (1) the declustering potential of the precursor ion in the SIM mode, (2) the selected transition and (3) the collision energy in the MRM mode. Consequently, quantification by summation of the peak areas of the isomers is inaccurate due to over‐ or underestimating of one of the stereoisomers. Accurate quantitative results can only be achieved when the compound‐specific MS parameters are separately determined for each isomer. This can be done by using pure isomers or by the determination of the MS parameters after HPLC separation and the measurement of the actual isomer ratio with an independent technique. Copyright © 2010 John Wiley & Sons, Ltd.     

Characterization and pattern recognition of oil-sand naphthenic acids using comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry

Oil-sand naphthenic acids (NAs) are organic wastes produced during the oil-sand digestion and extraction processes and are very difficult to separate and analyze as individual components due to their complex compositions. A comprehensive two-dimensional gas chromatography/time of flight mass spectrometry (GC x GC/TOF-MS) system was applied for the characterization of two commercial mixtures of naphthenic acids (Fluka and Acros) and a naphthenic acid sample extracted from the Syncrude tailings. Contour plots of chromatographic distributions of different Z homologous series of the Fluka, Acros and Syncrude NAs were constructed using fragment ions that were characteristic of the NA's molecular structures. Well-ordered patterns were observed for NAs of Z= 0 and -2 which corresponded to acyclic acids and monocyclic acids, respectively. For NAs of Z= -4, -6, and -8, specific zones were observed which would allow the pattern recognition of these NAs obtained from different origins. As expected, gas chromatographic retention times increase with the number of the carbons and the number of rings in the molecules. Little signal was obtained for NAs with Z numbers of -10, or lower. Deconvoluted mass spectra of various NA isomers were derived from the reconstructed GC x GC chromatogram, permitting detailed structural elucidations for NAs in the future. The current study demonstrated that the combination of GC x GC and the TOF-MS is a powerful to identify origins of the NAs in an effective manner. GC x GC/TOF-MS alone, however, may not be enough to characterize each individual isomer in a complex mixture such as NAs. The use of mass deconvolution software followed by library search have thus become necessary to separate and study the mass spectrum of each individual NA component, allowing a detailed identification of the toxic components within the NAs mixture.     

Reversed-phase high-performance liquid chromatographic behavior of peptide isomers including a D-amino acid

Summary The chromatographic behavior of ten peptide isomers was investigated using isocratic eluting with reversedphase high-performance liquid chromatography. These peptides are growth hormone releasing factor, consisting of 29 amino acid residues and its isomers where on amino acid residue in the sequence was replaced with the corresponding D-amino acid. Linear relationship was observed between the logarithm of the capacity factors of the isomers and the acetonitrile concentration in the mobile phase with correlation coefficients of 0.995–0.998. The regression coefficients were almost the same for all the isomers with a relative standard deviation of 5.3%. These results suggest that the chromatographic behavior of peptide isomers is also predictable from the solvophobic theory. The regression coefficient reflects the molecular weight and the Y-intercept represents the hydrophobicity of the isomer. The peptide isomers can be separated from one another, based on the differences in the hydrophobicity of each isomer.     

Distinguishing of 2‐MAPB and 6‐MAPB: Solution of the problem

Differentiation of new psychoactive substance (NPS), 6‐(2‐methylaminopropyl)benzofuran (6‐MAPB), and its positional isomer, 2‐(2‐methylaminopropyl)benzofuran (2‐MAPB), by means of gas chromatography/mass spectrometry (GC/MS) with quadrupole detection is ambiguous. Reliable distinguishing of the two isomers could be achieved by MS/MS spectra recorded after collision‐induced dissociation (CID) of precursor ions. Both electron ionization (EI) and electrospray ionization (ESI) methods could be used for these purposes.     

Synthesis, spectroscopic, and electrochemical studies of 1,2-naphthalene-ring-fused tetraazachlorins, -bacteriochlorins, and -isobacteriochlorins: the separation and characterization of structural isomers

1,2-Naphthalene-ring-expanded tetraazachlorins (TACs), tetraazabacteriochlorins (TABCs), and tetraazaisobacteriochlorins (TAiBCs) have been synthesized. Procedures for the synthesis of the starting materials, that is, derivatives of 1,2-naphthalenedicarboxylic acid, have been reinvestigated and improved. Nine possible derivatives, including four, two, and three structural isomers of TACs, TABCs, and TAiBCs, respectively, were separated by using thin-layer chromatography (TLC) or high-performance liquid chromatography (HPLC), and the structure of each isomer was determined by (1)H NMR spectroscopy combined with the NOE technique. The formation ratio of each isomer was rationalized in terms of the intramolecular steric repulsion effect, which was predicted by geometry optimizations at the DFT level. The derived compounds were characterized by using IR, electronic, and magnetic circular dichroism (MCD) spectroscopy, and by electrochemical methods. Frequency calculations at the DFT level correctly reproduced the experimental IR spectra and, in particular, distinguished between the three isomers of the TAiBCs. In the electronic absorption and MCD spectra of the TAC and TABC species, the Q-band splits into two intense components similarly to the 2,3-naphthalene-fused derivatives described in our preceding paper, although no significant spectral differences were observed from species to species. On the other hand, the spectra of the TAiBCs showed moderate differences depending on the structure of the isomer. The spectroscopic properties as well as the electrochemical behavior of these chlorins resemble those of the corresponding benzene-fused derivatives rather than the 2,3-naphthalene-fused derivatives. Molecular-orbital and configuration-interaction calculations within the framework of the ZINDO/S method were helpful in the discussions of the above observations.     

Investigation of sulphur compounds in coal tar using monodimensional and comprehensive two-dimensional gas chromatography

Coal is a non renewable fossil fuel, used mainly as a source of electrical energy and in the production of coke. It is subjected to thermal treatment, pyrolysis, which produces coke as a main product, in addition to a condensed liquid by-product, called tar. Tar is a complex mixture of organic compounds which contains different chemical classes, presenting aromatic and sulphur heterocyclic compounds. In general, identification of these compounds requires steps of isolation and fractionation, mainly due to co-elution of these compounds with polyaromatic hydrocarbons (PAH). The objective of this work is to characterize the sulphur compounds present in the coal tar obtained via pyrolysis, using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry detector (GC×GC/TOFMS). Coal samples from the State of Paraná, Brazil were subjected to laboratorial scale pyrolysis. Several experimental conditions were tested, such as sample weight (5, 10 and 15g), heating ramp (10, 25 and 100°C/min) and final temperature (500, 700 and 900°C). Samples were analyzed by one dimensional gas chromatography (1D-GC) coupled to a quadrupole mass spectrometry detector (GC/qMS) and two-dimensional gas chromatography with time-of-flight mass spectrometry detector (GC×GC/TOFMS). The higher amount of sulphur compounds was obtained at a final temperature of 700°C and a heating ramp of 100°C/min. The main classes observed in the color plot were thiophenes, benzothiophenes and alkylated dibenzothiophenes. GC×GC/TOFMS allowed the identification of the greater number of compounds and the separation of several sulphur compounds from one another. Moreover, separation of sulphur compounds from polyaromatic hydrocarbons and phenols was achieved, which was not possible by 1D-GC. Comparing GC×GC/TOFMS and 1D-GC (SIM mode) also showed that 1D-GC, one of the most employed quantification tools for sulphur compounds, can be misleading for detection, identification and quantification, as the number of isomers of sulphur compounds found was greater than theoretically possible.     

Comparison of the use of mass spectrometry and methylene unit values in the determination of the stereochemistry of estranediol, the major urinary metabolite of 19-nortestosterone in the horse

The stereochemistry of an isomer of 5-estrane-3,17 alpha-diol, the major metabolite of 19-nortestosterone in horse urine has been established by the use of methylene unit (MU) values. The empirical MU values of the bis-trimethylsilyl (TMS) derivatives of the eight available isomers of 5-androstane-3,17-diol and four isomers of 5-estrane-3,17 beta-diol were determined by capillary gas chromatography using three different columns. From this data the theoretical MU values for the bis-TMS derivatives of the four 5-estrane-3,17 alpha-diol isomers were predicted. Comparison of the experimentally determined MU value of the urinary metabolite with those of the theoretical values established the correct stereochemistry of the steroid. This method has been compared with the use of gas chromatography-mas spectrometry in the determination of the stereochemistry of unknown metabolites.     

Improved identification of conjugated linoleic acid isomers using silver-ion HPLC separations

Silver-ion high-performance liquid chromatography (Ag+-HPLC) has been shown to be effective in the resolution of most of the isomers of conjugated octadecadienoic acids (18:2), also known as conjugated linoleic acid (CLA). The CLA isomers identified in natural fats from ruminants are a mixture of numerous positional and geometric isomers from 7,9- to 12,14-18:2. Ag+-HPLC separates both geometric (trans,trans < cis/trans < cis,cis) and positional CLA isomers using the mobile phase hexane/acetonitrile (99.9:0.1). The elution volumes for the CLA isomers were not only affected by the concentration of acetonitrile (in the prepared mobile phase) but also with successive runs during the day using a prepared mobile phase batch, due to the partial solubility of acetonitrile in hexane. However, this drift does not affect the relative resolution of the CLA isomers. The addition of diethyl ether to the mobile phase partly stabilizes the solvent mixture. In order to facilitate the interpretation of Ag-+HPLC chromatograms, the relative retention volumes (RRV) were calculated for each CLA isomer. Toluene was added to all the test portions and served as an estimator of dead volume, whereas the elution of the ubiquitous 9c,11t-CLA isomer was chosen as unity (1.00). Expressing the elution of all the CLA isomers as their RRV greatly helped to standardize each CLA isomer, resulting in relatively small coefficients of variation (% CV) for the trans,trans (<1.5%) and cis/trans (<0.5%) CLA isomers. The identification of the CLA isomers was further facilitated by synthesis of authentic CLA isomers. All the geometric CLA fatty acid methyl esters (FAME) from positions 6,8- to 13,15-CLA were commercially available or synthesized by a combination of partial hydrazine reduction of known polyunsaturated fatty acids followed by alkali isomerization, isolation of products, and further iodine-catalyzed geometric isomerization. Based on expressing the elution volume as RRV and the availability of the synthetic CLA isomers, a unique reversal of the elution order of the c/t CLA isomers was found. It is also proposed that the retention times of CLA isomers by gas chromatography (GC) should be expressed as their relative retention times (RRT) relative to methyl gamma-linoleneate. The availability of CLA reference materials and the application of RRV and RRT to Ag+-HPLC and GC separations, respectively, will greatly improve in the identifications of CLA isomers.