Pressurised membrane-assisted liquid extraction of UV filters from sludge

A method for the determination of 11 UV-filter compounds in sludge has been developed and evaluated. The procedure includes the use of non-porous polymeric membranes in combination with pressurised liquid extraction (PLE). Firstly, the solid sample, wetted with the extraction solvent, was enclosed into tailor-made bags prepared with low density polyethylene. Secondly, these packages were submitted to a conventional PLE (70 °C, 4 cycles of 5 min static time). Finally, the analytes were determined by liquid chromatography–atmospheric pressure photoionisation–tandem mass spectrometry. The main advantage of this procedure is the reduction of time, solvent and labour effort ought to the combination of extraction and clean-up in a single step. Although the extraction is not quantitative (thus, standard addition is recommended for quantification) selectivity is clearly gained using the membrane as a consequence of the differences of permeation and transport through the membrane between the analytes and other sample matrix components. The optimised protocol provides limits of detection ranging from 0.3 ng g⁻¹ (ethylhexyl dimethyl p-aminobenzoate (OD-PABA)) to 25 ng g⁻¹ (ethylhexyl triazone (EHT)) with only 0.5 g of sludge sample. All the studied UV filters were found in the samples at concentration levels between 1.4 and 2479 ng g⁻¹, emphasising the high adsorption potential of this kind of environmental pollutants onto solid samples such as sludge. Also, this method has permitted the determination of seven of the studied UV filters in sludge samples for the first time.     

Determination of tetrabromobisphenol-A,tetrachlorobisphenol-A and bisphenol-A in soil by ultrasonic assisted extraction and gas chromatography–mass spectrometry

In this work, an isotope dilution method for the determination, in agricultural and industrial soil samples, of tetrabromobisphenol-A, tetrachlorobisphenol-A and bisphenol-A by gas chromatography–mass spectrometry was developed. The compounds were extracted from soil by sonication assisted extraction in small columns (SAESC) with a low volume of ethyl acetate as extraction solvent. For dirty soil samples, such as industrial soils, a simultaneous clean-up on an acidified Florisil–anhydrous sodium sulfate mixture was carried out to remove interferences. After extraction, solvent was evaporated and analytes were derivatized with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) and determined by isotope dilution gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC–MS–SIM), using ¹³C₁₂ labeled compounds as internal standards. Recoveries from spiked samples were between 88% and 108% and the estimated limits of detection (S/N = 3) varied from 30 pg g⁻¹ to 90 pg g⁻¹. The response obtained with this method was linear over the range assayed, 5–300 ng ml⁻¹, with correlation coefficients equal or higher than 0.999. The validated method was used to investigate the levels of these phenolic compounds in soil samples collected from different locations in Spain. Bisphenol-A was detected in all samples at concentrations from 0.7 ng g⁻¹ to 4.6 ng g⁻¹ in agricultural soils and from 1.1 ng g⁻¹ to 44.5 ng g⁻¹ in industrial soils. Tetrabromobisphenol-A was found in various soil samples at levels in the range of 3.4–32.2 ng g⁻¹ in industrial soils and at 0.3 ng g⁻¹ in one agricultural soil, whereas tetrachlorobisphenol-A was not detected.     

Investigation of plant hormone level changes in shoot tips of longan (Dimocarpus longan Lour.) treated with potassium chlorate by liquid chromatography-electrospray ionization mass spectrometry

The endogenous levels of indole-3-acetic acid (IAA), gibberellins (GAs), abscisic acid (ABA) and cytokinins (CKs) and their changes were investigated in shoot tips of ten longan (Dimocarpus longan Lour.) trees for off-season flowering until 60 days after potassium chlorate treatment in comparison with those of ten control (untreated) longan trees. These analytes were extracted and interfering matrices removed with a single mixed-mode solid phase extraction under optimum conditions. The recoveries at three levels of concentration were in the range of 72-112%. The endogenous plant hormones were separated and quantified by liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS). Detection limits based on the signal-to-noise ratio ranged from 10 ng mL⁻¹ for gibberellin A4 (GA4) to 200 ng mL⁻¹ for IAA. Within the first week after potassium chlorate treatment, dry weight (DW) amounts in the treated longan shoot tips of four gibberellins, namely: gibberellin A1(GA1), gibberellic acid (GA3), gibberellin A19 (GA19) and gibberellin A20 (GA20), were found to increase to approximately 25, 50, 20 and 60 ng g⁻¹ respectively, all of which were significantly higher than those of the controls. In contrast, gibberellin A8 (GA8) obtained from the treated longan was found to decrease to approximately 20 ng g⁻¹ DW while that of the control increased to around 80 ng g⁻¹ DW. Certain CKs which play a role in leaf bud induction, particularly isopentenyl adenine (iP), isopentenyl adenosine (iPR) and dihydrozeatin riboside (DHZR), were found to be present in amounts of approximately 20, 50 and 60 ng g⁻¹ DW in the shoot tips of the control longan. The analytical results obtained from the two-month off-season longan flowering period indicate that high GA1, GA3, GA19 and GA20 levels in the longan shoot tips contribute to flower bud induction while high levels of CKs, IAA and ABA in the control longan contribute more to the vegetative development.     

Simultaneous identification of glucosinolates and phenolic compounds in a representative collection of vegetable Brassica rapa

Brassica raparapa group is widely distributed and consumed in northwestern Spain. The consumption of Brassica vegetables has been related to human health due to their phytochemicals, such as glucosinolates and phenolic compounds that induce a variety of physiological functions including antioxidant activity, enzymes regulation and apoptosis control and the cell cycle. For first time in Brassica crops, intact glucosinolates and phenolic compounds were simultaneously identified and characterized. Twelve intact glucosinolates, belonging to the three chemical classes, and more than 30 phenolic compounds were found in B. rapa leaves and young shoots (turnip greens and turnip tops) by LC–UV photodiode array detection (PAD)–electrospray ionization (ESI). The main naturally occurring phenolic compounds identified were flavonoids and derivatives of hydroxycinnamic acids. The majority of the flavonoids were kaempferol, quercetin and isorhamnetin glycosylated and acylated with different hydroxycinnamic acids. Quantification of the main compounds by HPLC-PAD showed significant differences for most of compounds between plant organs. Total glucosinolate content value was 26.84 μmol g⁻¹ dw for turnip greens and 29.11 μmol g⁻¹ dw for turnip tops; gluconapin being the predominant glucosinolate (23.2 μmol g⁻¹ dw). Phenolic compounds were higher in turnip greens 51.71 μmol g⁻¹ dw than in turnip tops 38.99 μmol g⁻¹ dw, in which flavonols were always the major compounds.     

Rapid and simultaneous analysis of dichlorvos, malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid in citrus fruit by flow-injection ion spray ionization tandem mass spectrometry

A simple method for the rapid and simultaneous analysis of dichlorvos (DDVP), malathion, carbaryl, and 2,4-dichlorophenoxy acetic acid (2,4-D) in citrus fruit, which uses flow-injection ion spray ionization tandem mass spectrometry, has been developed for the first time. The method involves the combined use of stable isotopically labeled internal standards (DDVP-d₆, malathion-d₁₀, carbaryl-d₇, and 2,4-D-d₅) and a multiple reaction monitoring technique. The average recoveries for the pesticides at the same concentrations as their tolerance levels (DDVP: 0.1-0.2 μg g⁻¹; malathion: 0.5-4.0 μg g⁻¹; carbaryl: 1.0 μg g⁻¹; 2,4-D: 1.0-2.0 μg g⁻¹) ranged from 90 to 119% with the relative standard deviation (R.S.D.) ranging from 1.0 to 13.1% (n = 5). Analysis time, including sample preparation and determination, was only 15 min. The present method is effective for screening DDVP, malathion, carbaryl, and 2,4-D in citrus fruit.     

Simultaneous distillation-extraction of high-value volatile compounds from Cistus ladanifer L

The present paper describes a procedure to isolate volatiles from rock-rose (Cistus ladanifer L.) using simultaneous distillation-extraction (SDE). High-value volatile compounds (HVVC) were selected and the influence of the extraction conditions investigated. The effect of the solvent nature and extraction time on SDE efficiency was studied. The best performance was achieved with pentane in 1 h operation. The extraction efficiencies ranged from 65% to 85% and the repeatability varied between 4% and 6% (as a CV%).The C. ladanifer SDE extracts were analysed by headspace solid phase microextraction (HS-SPME) followed by gas chromatography with flame ionization detection (GC-FID). The HS-SPME sampling conditions such as fiber coating, temperature, ionic strength and exposure time were optimized. The best results were achieved with an 85 μm polyacrylate fiber for a 60 min headspace extraction at 40 °C with 20% (w/v) of NaCl. For optimized conditions the recovery was in average higher than 90% for all compounds and the intermediate precision ranged from 4 to 9% (as CV %). The volatiles α-pinene (22.2 mg g⁻¹ of extract), 2,2,6-trimethylcyclohexanone (6.1 mg g⁻¹ of extract), borneol (3.0 mg g⁻¹ of extract) and bornyl acetate (3.9 mg g⁻¹ of extract) were identified in the SDE extracts obtained from the fresh plant material.     

Identification of S-methylmethionine in Petit Manseng grapes as dimethyl sulphide precursor in wine

A procedure for the extraction of free amino acids was applied to isolate S-methylmethionine (SMM) from late harvest Petit Manseng grapes. Grapes were destemmed and crushed, and the obtained clarified must was percolated through cation-exchange resins (Dowex 50 WX4-100). The retained compounds were eluted with ammonia solution and the extract was finally concentrated. Taking into account the potential DMS (PDMS using heat-alkaline treatment assay) of the initial grape juice used (51.5 nmol mL⁻¹) and the concentration factor of the extract (17.9-fold), the PDMS of the final extract (678 nmol mL⁻¹) gave an overall recovery of 73.5% for juice SMM. This compound was identified and quantified (484.5 nmol mL⁻¹ relatively to [²H₃]-SMM used as internal standard) by its selective detection in this extract without derivatization by MALDI-TOF-MS using instrumentation and procedures previously reported to analyze SMM in complex natural extracts. SMM and 22 other amino acids in the initial must and in the final SMM extract were also determined using a Biochrom 30 amino acid analyser with post-column ninhydrin derivatization. SMM peak identification and quantification (401.2 nmol mL⁻¹ relatively to norleucine used as internal standard) were carried out by comparison with commercial SMM.     

Flow-injection catalytic spectrophotometic determination of molybdenum(VI) in plants using bromate oxidative coupling of p-hydrazinobensenesulfonic acid with N-(1-naphthyl)ethylenediamine

A novel flow-injection spectrophotometry has been developed for the determination of molybdenum(VI) at nanograms per milliliter levels. The method is based on the catalytic effect of molybdenum(VI) on the bromate oxidative coupling of p-hydrazinobenzenesulfonic acid with N-(1-naphthyl)ethylenediamine to form an azo dye (λ_max = 530 nm). Chromotropic acid (4,5-dihydroxy-2,7-naphthalenedisulfonic acid) acted as an effective activator for the molybdenum(VI)-catalyzed reaction and increased the sensitivity of the method. The reaction was monitored by measuring the change in absorbance of the dye produced. The proposed method allowed the determination of molybdenum(VI) in the range 1.0-20 ng mL⁻¹ with sample throughput of 15 h⁻¹. The limit of detection was 0.5 ng mL⁻¹ and a relative standard deviation for 10 ng mL⁻¹ molybdenum(VI) (n = 10) was 2.5%. The interfering ions were eliminated by using the combination of a masking agent and on-line minicolumn packed with cation exchanger. The present method was successfully applied to the determination of molybdenum(VI) in plant foodstuffs.     

Non-porous membrane-assisted liquid–liquid extraction of UV filter compounds from water samples

A method for the determination of nine UV filter compounds [benzophenone-3 (BP-3), isoamyl methoxycinnamate, 4-methylbenzylidene camphor, octocrylene (OC), butyl methoxydibenzoylmethane, ethylhexyl dimethyl p-aminobenzoate (OD-PABA), ethylhexyl methoxycinnamate (EHMC), ethylhexyl salicylate and homosalate] in water samples was developed and evaluated. The procedure includes non-porous membrane-assisted liquid–liquid extraction (MALLE) and LC–atmospheric pressure photoionisation (APPI)–MS/MS. Membrane bags made of different polymeric materials were examined to enable a fast and simple extraction of the target analytes. Among the polymeric materials tested, low- and high-density polyethylene membranes proved to be well suited to adsorb the analytes from water samples. Finally, 2 cm length tailor-made membrane bags were prepared from low-density polyethylene in order to accommodate 100 μL of propanol. The fully optimised protocol provides recoveries from 76% to 101% and limits of detection (LOD) between 0.4 ng L⁻¹ (OD-PABA) and 16 ng L⁻¹ (EHMC). The interday repeatability of the whole protocol was below 18%. The effective separation of matrix molecules was proved by only marginal matrix influence during the APPI-MS analysis since no ion suppression effects were observed. During the extraction step, the influence of the matrix was only significant when non-treated wastewater was analysed. The analysis of lake water indicated the presence of seven UV filter compounds included in this study at concentrations between 40 ng L⁻¹ (BP-3) and 4381 ng L⁻¹ (OC). In non-treated wastewater several UV filters were also detected at concentration levels as high as 5322 ng L⁻¹ (OC).     

Non-chromatographic speciation of toxic arsenic in fish

A rapid, sensitive and economic method has been developed for the direct determination of toxic species of arsenic present in fish and mussel samples. As(III), As(V), dimethylarsinic acid (DMA), and monomethylarsonic acid (MMA) were determined by hydride generation-atomic fluorescence spectrometry using a series of proportional equations without the need of a chromatographic previous separation. The method is based on the extraction of arsenic species from fish through sonication with HNO₃ 3 mol l⁻¹ and 0.1% (m/v) Triton and washing of the solid phase with 0.1% (m/v) EDTA, followed by direct measurement of the corresponding hydrides in four different experimental conditions. The limit of detection of the method was 0.62 ng g⁻¹ for As(III), 2.1 ng g⁻¹ for As(V), 1.8 ng g⁻¹ for MMA and 5.4 ng g⁻¹ for DMA, in all cases expressed in terms of sample dry weight. The mean relative standard deviation values (R.S.D.) in actual sample analysis were: 6.8% for As(III), 10.3% for As(V), 8.5% for MMA and 7.4% for DMA at concentration levels from 0.08 mg kg⁻¹ As(III) to 1.3 mg kg⁻¹ DMA. Recovery studies provided percentages greater than 93% for all species in spiked samples. The analysis of SRM DORM-2 and CRM 627 certified materials evidenced that the method is suitable for the accurate determination of arsenic species in fish.     

Simultaneous qualitative assessment and quantitative analysis of flavonoids in various tissues of lotus (Nelumbo nucifera) using high performance liquid chromatography coupled with triple quad mass spectrometry

Flavonoid composition and concentration were investigated in 12 different tissues of ‘Ti-1’ lotus (Nelumbo nucifera) by high performance liquid chromatography equipped with photodiode array detection tandem electrospray ionization mass spectrometry (HPLC-DAD-ESI-MSⁿ). A total of 20 flavonoids belonging to six groups (myricetin, quercetin, kaempferol, isohamnetin, diosmetin derivatives) were separated and identified. Myricetin 3-O-galactoside, myricetin 3-O-glucuronide, isorhamnetin 3-O-glucuronide and free aglycone diometin (3′,5,7-trihydroxy-4′-methoxyflavone) were first reported in lotus. Flavonoid composition varied largely with tissue type, and diverse compounds (5–15) were found in leaf and flower stalks, flower pistils, seed coats and embryos. Flower tissues including flower petals, stamens, pistils, and, especially, reproductive tissue fruit coats had more flavonoid compounds (15–17) than leaves (12), while no flavonoids were detectable in seed kernels. The flavonoid content of seed embryos was high, 730.95 mg 100 g⁻¹ DW (dry weight). As regards the other tissues, mature leaf pulp (771.79 mg 100 g⁻¹ FW (fresh weight)) and young leaves (650.67 mg 100 g⁻¹ FW) had higher total flavonoid amount than flower stamens (359.45 mg 100 g⁻¹ FW) and flower petals (342.97 mg 100 g⁻¹ FW), while leaf stalks, flower stalks and seed coats had much less total flavonoid (less than 40 mg 100 g⁻¹ FW).     

Simultaneous determination of sulfamonomethoxine, sulfadimethoxine, and their hydroxy/N(4)-acetyl metabolites with gradient liquid chromatography in chicken plasma, tissues, and eggs

A simultaneous determination of sulfamonomethoxine, sulfadimethoxine, and their hydroxy/N⁴-acetyl metabolites in chicken plasma, muscle, liver, and eggs using gradient high-performance liquid chromatography (HPLC) with a photo-diode array detector is developed. All the compounds are extracted by a handheld ultrasonic homogenizer with ethanol followed by centrifugation. The separation is performed by a reversed-phase C4 column with a gradient elution (ethanol:1% (v/v) acetic acid, v/v; 10:90 → 20:80). Average recoveries from samples spiked at 0.1-1.0 μg g⁻¹ or μg ml⁻¹ for each drug were >90% with relative standard deviations within 4%. The limits of quantitation were <30 ng g⁻¹ or ng ml⁻¹.     

Ion-pair sorptive extraction of perfluorinated compounds from water with low-cost polymeric materials: Polyethersulfone vs polydimethylsiloxane

A method for the determination of seven perfluorinated carboxylic acids and perfluorooctane sulphonate (PFOS) in aqueous samples using low-cost polymeric sorptive extraction as sample preparation technique, followed by liquid chromatography–tandem mass spectrometry (LC–MS/MS) determination has been developed and validated. Simplicity of the analytical procedure, low volume of solvent and sample required, low global price and a good selectivity providing cleaner extracts are the main advantages of this extraction technique. Polydimethylsiloxane (PDMS) and polyethersulfone (PES) materials were evaluated and compared to achieve the best extraction efficiencies. Hence, different variables have been optimized, viz.: sample pH, concentration of an ion-pairing agent (tetrabutylammonium), ionic strength, sample volume, extraction time, desorption solvent volume, desorption time and the need for auxiliary desorption techniques (sonication). Overall, PES leaded to a better sensitivity than PDMS, particularly for the most polar compounds, reaching detection limits (LODs) in the 0.2–20 ng L⁻¹ range. The precision of the method, expressed as relative standard deviation (RSD), was lower than 16%. Finally, the PES material was employed for the analysis of sea, sewage and fresh water samples. Perfluoroheptanoic acid (PFHpA), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA) and perfluorodecanoic acid (PFDA) were detected in all the analyzed influent samples reaching levels of up to 401 ng L⁻¹. In surface water, perfluorohexanoic acid (PFHxA) exhibited the highest concentrations, up to 137 ng L⁻¹.     

Distribution and accumulation of antimony in plants in the super-large Sb deposit areas, China

Antimony (Sb) distribution and accumulation in plants in Xikuangshan Sb deposit area, the only one super-large Sb deposit in the world, Hunan, China were investigated. Results show that soils were severely polluted with the average Sb concentrations up to 5949.20 mg kg^− 1. Sb widely occurred in 34 plants with various concentrations ranging from 3.92 mg kg⁻¹ to 143.69 mg kg^− 1, Equisetaceae family has the highest concentration (98.23 mg kg^− 1) while Dryopteridacea family has the lowest one (6.43 mg kg^− 1). H. ramosissima species of Equisetaceae family had the highest Sb average concentration of 98.23 mg kg^− 1 and P. vittata species of Pteridaceae family showed advantage of accumulating Sb from the contaminated environment (Biological Accumulation Coefficient, BAC = 0.08). Almost all species enriched Sb in their upground part such as shoot, leaf and flower (Biological Transfer Coefficient, BTC > 1), which may attribute to the high acropetal coefficient and Sb transformation from the atmosphere to the plants. P. phaseoloides and D. indicum showed predominantly accumulation of Sb in the upground part with BTC of 6.65 and 5.47, respectively.From the low bioavailable fraction in soils and weak relationship between total soil concentrations in soils and plants, it seems that the Sb bioavailability was limited and varied with different soil sites as well as plant species. Those observations would be significant to the phytoaccumulation and phytoremediation of plants and ecological and environmental risk assessment in Sb contaminated areas.     

Simultaneous analysis of trans- and cis-isomers of 2-glucosyloxycinnamic acids and coumarin derivatives in Dendrobium thyrsiflorum by high-performance liquid chromatography (HPLC)-photodiode array detection (DAD)-electrospray ionization (ESI)-tandem mass spectrometry (MS)

A novel method has been developed for simultaneous analysis for three pairs of trans- and cis-isomers of 2-glucosyloxycinnamic acids, along with their biogenic metabolites (three coumarin derivatives including scopoletin, scoparone and ayapin) in a Chinese medicinal herb Dendrobium thyrsiflorum by using high-performance liquid chromatography (HPLC)-photodiode array detection (DAD)-electrospray ionization (ESI)-tandem mass spectrometry (MS). The method was carried out by using a Polaris C₁₈ column with a gradient solvent system of 0.5% acetic acid aqueous solution-acetonitrile. Seven target analytes including isodensifloside, isothyrsifloside, densifloside, thyrsifloside, scoparone, ayapin and scopoletin were exclusively identified by comparing their retention behaviors, UV and MS spectra with the authentic standards, and their contents in D. thyrsiflorum were simultaneous determined by employing UV detection at 342 nm. In addition, another pair of isomers of 2-glucosyloxycinnamic acids was putatively elucidated mainly based on the MS fragmentation. The method was validated and found to be satisfactorily linear, selective and robust. Recoveries ranged from 95.56 to 97.94% for all compounds at three different spiking levels. The limits of detection (LOD) and quantitation (LOQ) ranged, respectively, from 0.02 to 0.13 μg mL⁻¹ and 0.07 to 0.39 μg mL⁻¹ depending on various compounds. The established quality evaluation method was successfully used for evaluating the quality of D. thyrsiflorum samples of different organs and collections.     

Determination of indole-3-acetic acid and indole-3-butyric acid in mung bean sprouts using high performance liquid chromatography with immobilized Ru(bpy)3-KMnO4 chemiluminescence detection

A novel method for determination of indole-3-acetic acid (IAA) and indole-3-butyric acid (IBA) in an extract from mung bean sprouts using high performance liquid chromatography (HPLC) with chemiluminescence (CL) detection is described. The method is based on the CL reaction of auxin (indole-3-acetic acid and indole-3-butyric acid) with acidic potassium permanganate (KMnO₄) and tris(2,2′-bipyridyl)ruthenium(II), which was immobilized on the cationic ion-exchange resin. The chromatographic separation was performed on a Nucleosil RP-C18 column (i.d.: 250 mm × 4.6 mm, particle size: 5 μm, pore size: 100) with an isocratic mobile phase consisting of methanol-water-acetic acid (45:55:1, v/v/v). At a flow rate of 1.0 mL min⁻¹, the total run time was 20 min. Under the optimal conditions, the linear ranges were 5.0 × 10⁻⁸ to 5.0 × 10⁻⁶ g mL⁻¹ and 5.0 × 10⁻⁷ to 1.0 × 10⁻⁵ g mL⁻¹ for IAA and IBA, respectively. The detection limits were 2.0 × 10⁻⁸ g mL⁻¹ and 2.0 × 10⁻⁷ g mL⁻¹ for IAA and IBA, respectively. The relative standard deviation (RSD) of intra-day were 3.1% and 2.3% (n = 11) for 2 × 10⁻⁶ g mL⁻¹ IAA and 2 × 10⁻⁶ g mL⁻¹ IBA; The relative standard deviations of inter-day precision were 6.9% and 4.9% for 2 × 10⁻⁶ g mL⁻¹ IAA and 2 × 10⁻⁶ g mL⁻¹ IBA. The proposed method had been successfully applied to the determination of auxin in mung bean sprouts.     

Simultaneous determination of N-acetyl-p-aminophenol and p-aminophenol with poly(3,4-ethylenedioxythiophene) modified glassy carbon electrode

A sensitive and selective method was developed for the determination of N-acetyl-p-aminophenol (APAP) and p-aminophenol (PAP) using poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrode (GCE). Cyclic voltammetry and differential pulse voltammetry were used to investigate the electrochemical reaction of APAP and PAP at the modified electrode. Both APAP and PAP showed quasireversible redox reactions with formal potentials of 367 mV and 101 mV (vs. Ag/AgCl), respectively, in phosphate buffer solution of pH 7.0. The significant peak potential difference (266 mV) between APAP and PAP enabled the simultaneous determination both species based on differential pulse voltammetry. The voltammetric responses gave linear ranges of 1.0 × 10⁻⁶-1.0 × 10⁻⁴ mol L⁻¹ and 4.0 × 10⁻⁶-3.2 × 10⁻⁴ mol L⁻¹, with detection limits of 4.0 × 10⁻⁷ mol L⁻¹ and 1.2 × 10⁻⁶ mol L⁻¹ for APAP and PAP, respectively. The method was successfully applied for the determination of APAP and PAP in pharmaceutical formulations and biological samples.     

Flow-injection chemiluminescence determination of aminomethylbenzoic acid and aminophylline based on N-bromosuccinimide-luminol reaction

A novel and sensitive chemiluminescence (CL) method for the determination of aminomethylbenzoic acid and aminophylline coupled with flow-injection analysis (FIA) technique is developed in this paper. It is based on the inhibition effect of the studied drugs on the chemiluminescence emission of N-bromosuccinimide-luminol (NBS-luminol) system. Under the optimum conditions, the decreased CL intensity is linear with the concentration of aminomethylbenzoic acid in the range of 2×10⁻⁸ to 1.0×10⁻⁶ g ml⁻¹ and with the concentration of aminophylline in the range of 1×10⁻⁷ to 7.0×10⁻⁶ g ml⁻¹, respectively. The detection limit is 7.0×10⁻⁹ g ml⁻¹ for aminomethylbenzoic acid (3σ) and 3.4×10⁻⁸ g ml⁻¹ for aminophylline (3σ). The relative standard deviations (R.S.D.) for 11 parallel measurements of 2.0×10⁻⁷ g ml⁻¹ aminomethylbenzoic acid and 1.0×10⁻⁶ g ml⁻¹ aminophylline are 2.6 and 3.0%, respectively. The proposed methods have been applied for the determination of the studied drugs in their pharmaceutical formulations with satisfactory results. The possible use of the proposed system for the determination of aminomethylbenzoic acid in plasma sample was also tested. The possible inhibition mechanism of aminomethylbenzoic acid and aminophylline on luminol-NBS system was discussed briefly.     

A new liquid chromatography-tandem mass spectrometry method for determination of parabens in human placental tissue samples

Endocrine disruptors are a group of organic compounds widely used, which are ubiquitous in the environment and in biological samples. The main effect of these compounds is associated with their ability to mimic or block the action of natural hormones in living organisms, including humans. Parabens (esters of p-hydroxybenzoic acid) belong to this group of compounds. In this work, we propose a new liquid chromatography-tandem mass spectrometry (LC-MS/MS) method to asses the presence of parabens most commonly used in industrial applications (methyl-, ethyl-, propyl- and butyl-paraben) in samples of human placental tissue. The method involves the extraction of the analytes from the samples using ethyl acetate, followed by a clean-up step using centrifugation prior to their quantification by LC-MS/MS using an atmospheric pressure chemical ionization (APCI) interface in the negative mode. Deuterated bisphenol A (BPA-d₁₆) was used as surrogate. Found detection limits (LOD) ranged from 0.03 to 0.06 ng g⁻¹ and quantification limits (LOQ) from 0.1 to 0.2 ng g⁻¹, while inter- and intra-day variability was under 13.8%. The method was validated using standard addition calibration and a spike recovery assay. Recovery rates for spiked samples ranged from 82% to 108%. This method was satisfactorily applied for the determination of parabens in 50 placental tissue samples collected from women who live in the province of Granada (Spain).     

Sorptive potential of sunflower stem for Cr(III) ions from aqueous solutions and its kinetic and thermodynamic profile

The sorptive potential of sunflower stem (180-300 μm) for Cr(III) ions has been investigated in detail. The maximum sorption (≥85%) of Cr(III) ions (70.2 μM) has been accomplished using 30 mg of high density sunflower stem in 10 min from 0.001 M nitric and 0.0001 M hydrochloric acid solutions. The accumulation of Cr(III) ions on the sorbent follows Dubinin-Radushkevich (D-R), Freundlich and Langmuir isotherms. The isotherm yields D-R saturation capacity X_m = 1.60 ± 0.23 mmol g⁻¹, β = −0.00654 ± 0.00017 kJ² mol⁻², mean free energy E = 8.74 ± 0.12 kJ mol⁻¹, Freundlich sorption capacity K_F = 0.24 ± 0.11 mol g⁻¹, 1/n = 0.90 ± 0.04 and of Langmuir constant K_L = 6800 ± 600 dm³ mol⁻¹ and C_m = 120 ± 18 μmol g⁻¹. The variation of sorption with temperature (283-323 K) gives ΔH = −23.3 ± 0.8 kJ mol⁻¹, ΔS = −64.0 ± 2.7 J mol⁻¹ K⁻¹ and ΔG_298k = −4.04 ± 0.09 kJ mol⁻¹. The negative enthalpy and free energy envisage exothermic and spontaneous nature of sorption, respectively. Bisulphate, Fe(III), molybdate, citrate, Fe(II), Y(III) suppress the sorption significantly. The selectivity studies indicate that Cr(III), Eu(III) and Tb(III) ions can be separated from Tc(VII) and I(I). Sunflower stem can be used for the preconcentration and removal of Cr(III) ions from aqueous medium. This cheaper and novel sorbent has potential applications in analytical and environmental chemistry, in water decontamination, industrial waste treatment and in pollution abatement. A possible mechanism of biosorption of Cr(III) ions onto the sunflower stem has been proposed.