New method for preparation of polyoxometalate-capped gold nanoparticles, and their assembly on an indium-doped tin oxide electrode

Functionalized gold nanoparticles capped with polyoxometalates were prepared by a simple photoreduction technique where phosphododecamolybdates serve as reducing reagents, photocatalysts, and as stabilizers. TEM images of the resulting gold nanoparticles show the particles to have a relative narrow size distribution. Monolayer and multilayer structures of the negatively charged capped gold nanoparticles were deposited on a poly(vinyl pyridine)-derivatized indium-doped tin oxide (ITO) electrode via the layer-by-layer technique. The surface plasmon resonance band of the gold nanoparticles displays a blue shift on the surface of the ITO electrode. This is due to the substrate-induced charge redistribution in the gold nanoparticles and a change in the electromagnetic coupling between the assembled nanoparticles. The modified electrode exhibits the characteristic electrochemical behavior of surface-confined phosphododecamolybdate and excellent electrocatalytic activity. The catalysis of the modified electrode towards the model compound iodate was systematically studied. The heterogeneous catalytic rate constant for the electrochemical reduction of iodate was determined by chronoamperometry to be ca. 1.34?×?10⁵ mol^?1·L·s^?1. The amperometric method gave a linear range from 2.5?×?10^?6 to 1.5?×?10^?3 M and a detection limit of 1.0?×?10^?6 M. We believe that the functionalized gold nanoparticles prepared by this photoreduction technique are advantageous in terms of fabrication of sensitive and stable redox electrodes.

Streptavidin-enhanced surface plasmon resonance biosensor for highly sensitive and specific detection of microRNA

We are presenting a method for sensitive and specific detection of microRNA (miRNA) using surface plasmon resonance. A thiolated capture DNA probe with a short complete complementary sequence was immobilized on the gold surface of the sensor to recognize the part sequence of target miRNA, and then an oligonucleotide probe linked to streptavidin was employed to bind the another section of the target. The use of the streptavidin-oligonucleotide complex caused a ~5-fold increase in signal, improved the detection sensitivity by a factor of ~24, and lowered the detection limit to 1.7 fmol of miR-122. This specificity allowed a single mismatch in the target miRNA to be discriminated. The whole assay takes 30 min, and the surface of the sensor can be regenerated at least 30 times without loss in performance. The method was successfully applied to the determination of miRNA spiked into human total RNA samples.

Luminescent Ru(bpy)3 2+-doped silica nanoparticles for imaging of intracellular temperature

Silica nanoparticles doped with the luminescent temperature probe Ru(bpy)₃ ²⁺ were prepared by a modified Stöber method and are shown to enable optical sensing of intracellular temperatures. Based on the regrowth of silica nanoseeds, the ruthenium probe was easily incorporated and then covered with a shell of pure silica. The resulting nanothermometers were immune to the quenching by oxygen owing to the outer silica layer. The nanoparticles were further coated with poly-L-lysine in order to reduce cytotoxicity and to warrant cellular uptake. The luminescence of these nanosensors is rather sensitive to temperature in the physiological range (25–45 °C), with a decrease of ?1.26 % in intensity per °C increase in temperature. The nanosensors were internalized into living cells of a hepatocellular carcinoma cell line along with gold nanorods. These display longitudinal surface plasmon resonance absorption at ~808 nm that causes a local rise in temperature. The microscopically captured luminescence intensity of the nanosensors after 808 nm irradiation of the gold nanorods decayed with increasing temperature, thereby indicating successful imaging of temperature.

Highly sensitive and selective voltammetric detection of mercury(II) using an ITO electrode modified with 5-methyl-2-thiouracil, graphene oxide and gold nanoparticles

We have developed an electrochemical sensor for highly selective and sensitive determination of Hg(II). It is based on the specific binding of 5-methyl-2-thiouracil (MTU) and Hg(II) to the surface of an indium tin oxide (ITO) electrode modified with a composite made from graphene oxide (GO) and gold nanoparticles (AuNPs). This leads to a largely enhanced differential pulse voltammetric response for Hg(II). Following optimization of the method, a good linear relationship (R?=?0.9920) is found between peak current and the concentration of Hg(II) in the 5.0–110.0 nM range. The limit of detection (LOD) is 0.78 nM at a signal-to-noise ratio of 3. A study on the interference by several metal ions revealed no interferences. The feasibility of this method was demonstrated by the analyses of real water samples. The LODs are 6.9, 1.0 and 1.9 nM for tap water, bottled water and lake water samples, respectively, and recoveries for the water samples spiked with 8.0, 50.0 and 100.0 nM were 83.9–96.8 %, with relative standard deviations ranging from 3.3 % to 5.2 %.

Improving surface plasmon resonance imaging of DNA by creating new gold and silver based surface nanostructures

The use of nanoparticles (NPs) can substantially improve the analytical performance of surface plasmon resonance imaging (SPRi) in general, and in DNA sensing in particular. In this work, we report on the modification of the gold surface of commercial biochips with gold nanospheres, silica-coated gold nanoshells, and silver nanoprisms, respectively. The NPs were tethered onto the surface of the chip and functionalized with a DNA probe. The effects of tethering conditions and varying nanostructures on the SPRi signals were evaluated via hybridization assays. The results showed that coupling between planar surface plasmons and electric fields, generated by localized surface plasmons of the NPs, is mandatory for signal enhancement. Silver nanoprisms gave the best results in improving the signal change at a target DNA concentration of <50 nM by +50 % (compared to a conventional SPRi chip). The limit of detection for the target DNA was 0.5 nM which is 5 times less than in conventional SPRi.

Plasmonic nanoprobes for intracellular sensing and imaging

Recent advances in integrating nanotechnology and optical microscopy offer great potential in intracellular applications with improved molecular information and higher resolution. Continuous efforts in designing nanoparticles with strong and tunable plasmon resonance have led to new developments in biosensing and bioimaging, using surface-enhanced Raman scattering and two-photon photoluminescence. We provide an overview of the nanoprobe design updates, such as controlling the nanoparticle shape for optimal plasmon peak position; optical sensing and imaging strategies for intracellular nanoparticle detection; and addressing practical challenges in cellular applications of nanoprobes, including the use of targeting agents and control of nanoparticle aggregation.

Interaction of mercury(II) ions with immobilized apo-metallothioneins studied by scanning electrochemical microscopy combined with surface plasmon resonance

Scanning electrochemical microscopy (SECM) was combined with surface plasmon resonance (SPR) and applied for in-situ monitoring of the incorporation of Hg²⁺ by apo-metallothionein (apo-MT) immobilized on the SPR substrate. Hg²⁺ was anodically stripped from the Hg-coated SECM Pt tip and sequestered by apo-MT upon its diffusion to the SPR substrate. The high sensitivity of the SPR instrument enabled the detection of the change in the composition and structure of apo-MT molecules that was induced by the metal sequestration of Hg²⁺. The SPR response revealed that the saturation co-ordination number of Hg²⁺ binding to apo-MT was 18. Moreover, an unexpected collapse of the structure of MT was observed when the stoichiometric ratio of Hg²⁺/MT was ~70, and the structure cannot be further altered even by adding a large excess of Hg²⁺. This collapse was also confirmed by Raman spectroscopy. The results are potentially useful for a deeper understanding of the detoxification mechanism of MT to mercury ion.

A DNA biosensor based on resonance light scattering using unmodified gold bipyramids

We report on a novel biosensor for determining sequence-specific DNA. It is based on resonance light scattering (RLS) caused by the aggregation of gold bipyramids. These display localized surface plasmon resonance and can be used as a bioprobe. The absorption spectra and the transmission electron micrographs provide visual evidence of the aggregation of the gold bipyramids in the presence of DNA. The RLS intensity of the gold bipyramids increases with the concentration of the target DNA. The method was successfully applied to the determination of a 30-mer single-stranded oligonucleotide and works over the 0.1–10?nM concentration range.

A study on the direct electrochemistry and electrocatalysis of microperoxidase-11 immobilized on a porous network-like gold film: Sensing of hydrogen peroxide

We have prepared porous and network-like nanofilms of gold by galvanic replacement of a layer of copper particles acting as a template. The films were first characterized by scanning electron microscopy and X-ray diffraction, and then modified with cysteamine so to enable the covalent immobilization of the enzyme microperoxidase-11. The immobilized enzyme undergoes direct electron transfer to the underlying electrodes, and the electrode displays high electrocatalytic activity towards the reduction of oxygen and hydrogen peroxide, respectively, owing to the largely enhanced electroactive surface of the porous gold film. The detection limit of H₂O₂ is 0.4 μM (3 S/N).

Amperometric sensor for detection of bisphenol A using a pencil graphite electrode modified with polyaniline nanorods and multiwalled carbon nanotubes

We report on a simple and highly sensitive amperometric method for the determination of bisphenol A (BPA) using pencil graphite electrodes modified with polyaniline nanorods and multiwalled carbon nanotubes. The modified electrodes display enhanced electroactivity for the oxidation of BPA compared to the unmodified pencil graphite electrode. Under optimized conditions, the sensor has a linear response to BPA in the 1.0 and 400?μM concentration range, with a limit of detection of 10?nM (at S/N?=?3). The modified electrode also has a remarkably stable response, and up to 95 injections are possible with a relative standard deviation of 4.2% at 100?μM of BPA. Recoveries range from 86 to 102% for boiling water spiked with BPA from four brands of baby bottles.

A surface plasmon resonance study on the optical properties of gold nanoparticles on thin gold films

We report on an investigation of the optical properties of gold nanoparticles assembled as thin films of different thickness. The nanoparticles were linked to the surface of a gold chip by dithiol reagents and studied by surface plasmon resonance (SPR) spectroscopy and atomic force microscopy. There is good correlation between the experimental findings and theoretical simulation, and the respective data reveal the presence of ordered nanostructures in the assemblies. The shift in the SPR angle is linearly dependent on the particle size and the ratio of the different particles. SPR spectroscopy also reveals important information in terms of the optical constants of such films. This shall be further applied to in-situ quality control in the fabrication of optoelectronic, solar cell and semiconductor devices.

Surface chemical approach to single-step measurement of antibody in human serum using localized surface plasmon resonance biosensor on microtiter plate system

In clinical settings, serum antibody levels serve as markers of pathology. For example, antibodies related to autoimmune diseases are among the conventional targets in laboratory tests. Simple clinical tests can improve the efficacy of laboratory practice. This study describes a single-step, wash-free technique for optically detecting antibodies in human serum through the localized surface plasmon resonance (LSPR) of gold nanoparticles. As a proof-of-concept experiment, the amount of antibiotin dissolved in human serum was measured with a LSPR-based biosensor in a wash-free manner using a conventional 96-well microtiter plate and a plate reader. For an efficient surface modification of biosensors, zwitterionic copolymer was used as a scaffold on the gold nanoparticle surface to immobilize antigen and blocking reagent. Single-step, wash-free measurement of antibiotin in human serum was successfully achieved. In addition, nonspecific responses from serum contents were significantly reduced because both the copolymer and hydrophilic antigen reagent that we employed were composed of poly(ethylene oxide) spacer. Comparative experiments of the antigen-antibody reaction in serum to that in buffered solution revealed that serum is a favorable environment for the biological reaction. In conclusion, our gold-nanoparticle-based LSPR method may provide a rapid and simple way to measure the amount of antibody in serum quantitatively in clinical practice.

Microfluidic channel with embedded SERS 2D platform for the aptamer detection of ochratoxin A

A selective aptameric sequence is adsorbed on a two-dimensional nanostructured metallic platform optimized for surface-enhanced Raman spectroscopy (SERS) measurements. Using nanofabrication methods, a metallic nanostructure was prepared by electron-beam lithography onto a glass coverslip surface and embedded within a microfluidic channel made of polydimethylsiloxane, allowing one to monitor in situ SERS fingerprint spectra from the adsorbed molecules on the metallic nanostructures. The gold structure was designed so that its localized surface plasmon resonance matches the excitation wavelength used for the Raman measurement. This optofluidic device is then used to detect the presence of a toxin, namely ochratoxin-A (OTA), in a confined environment, using very small amounts of chemicals, and short data acquisition times, by taking advantage of the optical properties of a SERS platform to magnify the Raman signals of the aptameric monolayer system and avoiding chemical labeling of the aptamer or the OTA target.

Preparation of a nanocomposite film from poly(diallydimethyl ammonium chloride) and gold nanoparticles by in-situ electrochemical reduction, and its application to SERS spectroscopy and sensing of ascorbic acid

A nanocomposite film is described that is composed of alternating layers of poly(diallydimethyl ammonium chloride) and gold nanoparticles that interact through electrostatic forces. The films of varying thickness were prepared by the layer-by-layer technique, and Au-NPs were generated by electrochemical reduction of hexachloroauric acid. The composite films were characterized by UV?Cvis spectroscopy, X-ray photoelectron spectroscopy, and cyclic voltammetry. Most nanocomposite films exhibit linear, uniform, and regular layer-by-layer growth during the process of formation. The films exhibit unique performance in terms of surface enhanced Raman scattering and electrocatalytic activitiy towards the oxidation of ascorbic acid.

Highly sensitive and selective electrochemical detection of L-cysteine using nanoporous gold

Nanoporous gold (NPG) with uniform pore sizes and ligaments was prepared by using a simple dealloying method. NPG electrodes exhibit excellent electrocatalytic activity towards the oxidation of CySH and the mechanism for the electrochemical reaction of CySH on NPG has been discussed. Interestingly, if the operating potential is fixed at 0.65 V, a strong current is observed and interferences by tryptophan and tyrosine are avoided. The calibration plot is linear in the concentration range from 1 μM to 400 μM (R²?=?0.994), and the quantification limit is as low as 50 nM. The NPG-modified electrode has good reproducibility, high sensitivity and selectivity, can be used to sense CySH in aqueous solution.

The use of gold-silver core-shell nanorods self-assembled on a glass substrate can substantially improve the performance of plasmonic affinity biosensors

We report on an effective strategy for the enhancement in the sensitivity of localized surface plasmon resonance (LSPR). It is based on the use of gold-silver core-shell nanorods (Au-Ag-cs-NRs) immobilized on a glass substrate. The nanorods arrange themselves by self-assembly, and the resulting LSPR band of the Au-Ag-cs-NRs becomes sharper and more intense. The sensitivity to refractive index (RI) of the Au-Ag-cs-NRs on the glass support is ~281 nm per RI unit, which is better by about 30 % compared to gold nanorods immobilized on glass substrate. The system was applied to study the streptavidin-biotin affinity system which is widely used in biosciences. It is found that the red-shift of the LSPR peak linearly increases with the concentration of streptavidin in the 95 pM to 1.7 μM concentration range. The detection limit (at an S/N ratio of 3) is at 35 pM. The results reveal the merits of this approach in terms of label-free optical affinity sensing. Figure

Au-Ag core-shell nanorods self-assembled on glass substrates. The refractive index sensitivity was enhanced obviously. A strategy to amplify the response and fabricate a label-free optical biosensor     

Direct electrochemistry of hemoglobin on an ionic liquid carbon electrode modified with zinc tungstate nanorods

We have constructed a new electrochemical biosensor by immobilization of hemoglobin (Hb) and ZnWO₄ nanorods in a thin film of chitosan (CTS) on the surface of carbon ionic liquid electrode. UV–vis and FT-IR spectra reveal that Hb remains in its native conformation in the film. The modified electrode was characterized by scanning electron microscopy, electrochemical impedance spectroscopy and cyclic voltammetry. A pair of well-defined redox peaks appears which indicates direct electron transfer from the electrode. The presence of CTS also warrants biocompatibility. The electron transfer coefficient and the apparent heterogeneous electron transfer rate constant were calculated to be 0.35 and 0.757 s^?1, respectively. The modified electrode displays good electrocatalytic activity for the reduction of trichloroacetic acid with the detection limit of 0.613 mmol L^?1 (3σ). The results extend the protein electrochemistry based on the use of ZnWO₄ nanorods.

Surface activation of plasma-patterned carbon nanotube based DNA sensing electrodes

We have studied the effect of treatment of multiwalled carbon nanotubes (MWCNTs) for use in DNA-based biosensors with oxygen plasma. Well-patterned MWCNT electrodes were photolithographically fabricated on glass substrates. Pure oxygen was used for etching and functionalization of the MWCNT film in a lab-made plasma chamber. The resulting electrodes exhibited a dramatic change in the morphology of their surface, the chemical composition, and the electrochemical properties in terms of peak current and peak potential separation. The electrodes also showed increased DNA immobilization efficiency and much higher sensitivity in the detection of target DNA as compared to non-treated MWCNT electrodes. Plasma treatment was optimized and electrodes were characterized by atomic force microscopy, X-ray photoelectron spectroscopy, cyclic voltammetry, and differential pulse voltammetry.

Gold electrodes modified with gold nanoparticles and thio compounds for electrochemical sensing of dopamine alone and in presence of potential interferents. A comparative study

Gold electrodes were modified with self assembled layers (SAMs) composed of mercaptopropionic acid, thiodipropionic acid, dithiodipropionic acid, cysteamine and gold nanoparticles and used to study the electrooxidation of dopamine (DA) in solution at pH 7. SAMs endowed with gold nanoparticles gave the highest catalytic effect. The results showed that such electrodes are capable of resolving the oxidation peaks of DA, ascorbic acid, and uric acid which is most favourable with respect to the detection of DA in physiological matrices.

Electrochemical aptasensor for the determination of bisphenol A in drinking water

We present an electrochemical aptasensor for rapid and ultrasensitive determination of the additive bisphenol A (BPA) and for screening drinking water for the presence of BPA. A specific aptamer against BPA and its complementary DNA probe were immobilized on the surface of a gold electrode via self-assembly and hybridization, respectively. The detection of BPA is mainly based on the competitive recognition of BPA by the immobilized aptamer on the surface of the electrode. The electrochemical aptasensor enables BPA to be detected in drinking water with a limit of detection as low as 0.284 pg?mL^?1 in less than 30 min. This extraordinary sensitivity makes the method a most powerful tool for on-site monitoring of water quality and food safety.