液晶聚酯与环氧嵌段共聚物的合成及表征

近年来 ,人们利用高分子液晶作为热固性环氧树脂的改性剂 ,不仅可以提高环氧树脂的韧性和强度 ,而且可以改善其热性能 ,为制备高性能的环氧树脂提供了一条新的途径[1,2 ] .目前报道所使用的液晶聚合物大多为液晶聚酯[3 ] 或液晶性聚氨酯[4] ,这些液晶聚合物与环氧树脂由于存在相容性不好的问题 ,给其实际应用带来了困难 .为了改善二者的相容性 ,本文采用溶液法合成了末端带有反应活性基团的聚酯型液晶聚合物 ,将它再与双酚Ａ环氧预聚物反应 ,制得了高分子液晶环氧嵌段共聚物 ,其合成路线如下 :2ＨＯＣＯＯＣＨ3+ ＨＯ(ＣＨ2 ) 6 ＯＨ　　Ｈ…     

含联苯结构侧链液晶聚合物的合成及相行为的研究

液晶聚合物从结构上可分为3种:侧链型、主链型和主侧链型。侧链型液晶聚合物主要是聚丙烯酸酯类、聚硅氧烷类以及磷腈聚合物类。Gray等对聚丙烯酸酯类含不同取代基的联苯结构液晶聚合物进行了研究,结果表明无间隔基且取代基为氰基和饱和脂肪基时,该聚合物呈现近晶型液晶行为。为了增加介晶单元的长径比及刚性,本文在聚甲基丙烯酸酯侧链     

一种液晶环氧增韧环氧树脂的研究

环氧树脂具有优异的机械性能 ,耐高温以及良好的加工工艺性 .被广泛用于机械、航天、船舶等领域 .由于环氧树脂固化后断裂延伸率小 ,脆性大 ,使其应用受到了一定的限制 .为此 ,国内外学者对环氧树脂进行了大量的改性研究工作 .用含有“柔性链段”的固化剂固化环氧 ,在交联网络中引入柔性链段[1] ;在环氧基体中加入橡胶弹性体[2 ] 、热塑性树脂[3 ,4] 、液晶聚合物[5,6] 等分散相或用热固性树脂连续贯穿于环氧树脂网络中形成互穿、半互穿网络结构[7] ,以改善环氧树脂的韧性 .本文采用液晶环氧化合物原位复合增韧环氧树脂 ,考察了液晶环氧对环…     

含1,3,4-噁二唑甲壳型液晶聚合物的合成与表征

甲壳型液晶聚合物（mesogen-jacketed liquid crystal polymer,MJLCP）是1987年由周其凤教授[1]首先提出的概念.从化学结构看,甲壳型液晶聚合物属于侧链型,由烯类单体经链式聚合制得,容易得到高分子量的产物,具有一般柔性侧链型液晶聚合物的一些优点.但是与柔性侧链型液晶聚合物不同的是,MJLCP分子中的刚性液晶基元是通过腰部或重心位置与主链相联结的,在主链与刚性液晶基元的侧基之间只有很短或者没有柔性间隔基.由于在这类液晶聚合物的分子主链周围空间内刚性液晶基元的密度很高,分子主链被由液晶基元形成的外壳所包裹并被迫采取相对伸直的刚性链构象.因此,这类液晶聚合物又和主链型刚性链液晶聚合物相似,具有较明显的链刚性.近年来,周其凤课题组围绕甲壳型液晶聚合物深入开展了分子设计与合成、分子结构与性能等多方面的研究.其中,设计合成具有特定功能的甲壳型液晶聚合物是在以往研究工作和学科交叉融合的基础上发展起来的一项新的研究工作.将一些有特殊功能的基团引入到甲壳型液晶聚合物中会使其具有崭新的特性.     

基于L-异亮氨酸衍生物的液晶单体及其聚合物的合成与结构表征

通过对L-异亮氨酸化合物进行扩展性研究及分子设计,本论文合成了四种含(2S,3S)-3-甲基-2-氯戊酰氧基的手性液晶单体(M1～M4),然后再以六氯合铂酸为引发剂,将四种单体通过接枝聚合,获得了对应的聚硅氧烷类液晶高分子(P1～P4),采用FT-IR、1 H-NMR与GPC表征了所合成的中间体、手性液晶单体及其聚合物的化学结构与分子量及分布,结果符合分子设计.此外,采用旋光仪测定了手性单体的旋光度,研究表明:它们均为右旋化合物,其比旋光度随化合物刚性的增加而降低,而对于端基相同、液晶核刚性大小接近的单体,其比旋光度比较接近.     

新的含T－型二维液晶基元的液晶高分子的合成

采用低温溶液聚合方法，以Ｎ－（２，５－二羟基苯）亚甲基－４－取代苯胺和不同结构的二酰氯为单体，合成了两类新的高分子．聚合物的液晶行为用ＤＳＣ、偏光显微镜和Ｘ射线衍射进行了表征，发现其中一类为向列型热致液晶高分子，另一类则无液晶性．随单体结构的改变，聚合物的特性粘数、熔点（Ｔｍ）和液晶态的清亮点（Ｔｉ）均呈现规律性变化。     

含磷全芳族热致液晶共聚酯的合成及热性能

全芳族热致液晶聚酯因其优良的力学性能、热稳定性及较低的熔融粘度而倍受关注 ,是当今最有前途的特种高分子材料之一 .但是 ,全芳族聚酯的刚性结构使其熔点较高 ,难以加工 ,因而通过分子设计制备熔点较低的热致全芳香族聚酯液晶成为研究的热点 .在主链型热致液晶高分子的分子设计中 ,通常采用共聚或在高分子链中引入取代基、柔性链段、扭结成分等方法来达到降低聚合物相转变温度的目的[1～ 6 ] .本文以对羟基苯甲酸、对苯二甲酸、间苯二甲酸和含磷二元酚化合物为单体 ,合成了一类具有较低熔点或流动温度的新型全芳族热致共聚酯液晶 ,其分子…     

硅碳烷树枝状液晶的研究

树技状化合物具有规整的结构，其分子体积、形状和功能基团可在分子水平上精确控制[1]，迄今国内只有综述报道[2]．传统的液晶分子为刚性棒状，按经典液晶理论，树枝状分子难以存在液晶态，迄今仅见3例多技聚合物显示热致或液致液晶性D－“．nercec［’咱称首次合成热致液晶树枝状聚合物TPD－bx，但据Ringsdorf［51分类，因其未采用逐步发散或收敛法，而用一锅煮法合成，产品结构不规整，分子量不单一．故仍属于多技聚合物．本文首次合成了液晶硅碳烷树技状化合物．1硅碳烷树技状化合物的结构树枝状化合物的结构见图1，主干为硅碳烷，含12…     

侧链聚硅氧烷液晶高分子的合成与表征及应用研究

液晶高分子既具有独特的液晶性 ,又具有高分子的良好材料性能 ,引起了人们的广泛注意[1～ 9] .侧链液晶高分子大多可以作为功能材料 ,对它们的研究有很大的理论与现实意义 .以往报道的此类化合物的介晶基元大多是通过烷氧基与间隔基相连[10 ] .我们以催化活性很高的铂络和物为催化剂 ,通过硅氢加成反应制备了间隔基与介晶基元通过酰氧基相连的两种侧链聚硅氧烷液晶高分子 ,并对它们的性质进行了初步表征 .发现它们具有很好的液晶性 .已有研究表明侧链聚硅氧烷液晶在气相色谱分离结构近似的物质方面 ,具有易涂渍、选择性及热稳定性优于低分子…     

新的含T-型二维液晶基元的液晶高分子的合成

采用低温溶液聚合方法,以N-(2,5-二羟基苯)亚甲基-4-取代苯胺和不同结构的二酰氯为单体,合成了两类新的高分子。聚合物的液晶行为用DSC、偏光显微镜和X射线衍射进行了表征,发现其中一类为向列型热致液晶高分子,另一类则无液晶性。随单体结构的改变,聚合物的特性粘数、熔点(Tm)和液晶态的清亮点(Ti)均呈现规律性变化。     

Synthesis and hydrolysis behaviour of poly(ester anhydrides) from polylactone precursors containing alkenyl moieties

Hydroxyl-group functional polylactones were prepared and converted to acid- terminated polyesters in a reaction with a series of alkenylsuccinic anhydrides containing 8, 12, or 18 carbons in their alkenyl chains. These polyester precursors were then linked into higher molecular weight poly(ester anhydrides) containing alkenyl moieties in their polyester blocks. The hydrolysis behaviour of the poly(ester anhydrides) was found to depend on the thermal properties of the polyester precursors. For poly(ester anhydrides) prepared from low molecular weight prepolymers with thermal transitions below 37 degrees C, the presence of hydrophobic alkenyl chains in the polyester precursors slowed the rate of weight loss. Poly(ester anhydrides) prepared from higher molecular weight prepolymers showed the opposite weight-loss behaviour; i.e., the crystallinity and thermal transitions of the alkenyl chain-containing poly(ester anhydrides) were low, and the weight loss was faster than for poly(ester anhydrides) without the alkenyl chains. The differences in length of the alkenyl chain, as such, had little effect on the hydrolysis behaviour and thermal properties of the poly(ester anhydrides).     

烯烃共聚酯的合成与表征

通过环辛烯、环辛二烯和降冰片烯与ω-十一烯酸乙二醇二酯的易位共聚合及氢化反应合成了烯烃共聚酯.改变聚合条件,可控制烯烃共聚酯的分子量、极性单体插入率和熔融温度等性质.两段聚合过程适于制备高分子量的烯烃共聚酯,聚合物收率达90%,极性单体的插入率大于10%,熔融温度高达120℃.     

可降解磷酸酯聚合物的合成与应用研究进展

磷酸酯类聚合物在自然界中可以降解,是环境友好的化学品.其中,分子量高的聚磷酸酯近年来在医药、塑料助剂等方面有广泛应用,分子量相对较低的磷酸酯类聚合物在饲料、表面活性剂等方面很重要.按用途的不同,综述了可降解磷酸酯聚合物的合成与应用近况.     

Termination Mechanism in the Anionic Polymerization of Methyl Methacrylate

Recent studies have revealed that at temperatures around 200°K in tetrahydrofuran solvent, poly(methy1 methacrylate) ion pairs are long-lived and very reactive. At higher temperatures however termination of the ion pairs occurs, as evidenced by the broadening of the molecular weight distribution of the resultant polymer and by the incomplete polymerization of the monomer. Three mechanisms have been proposed to describe these termination reactions; an inter molecular reaction with the monomer ester function, an intramolecular cyclization of the anion, or reaction with the polymer ester function. In the absence of monomer only the last two mechanisms can be operative. A series of experiments was undertaken in which the molecular weight distribution broadening with temperature increase was measured under typical polymerization conditions or in the absence of monomer. The effect of each of the three counterions Li, Na, and K was also monitored. The results obtained are discussed in terms of these three possible termination mechanisms. Termination rate constants calculated from the molecular weight distribution are also presented.     

Polymerization and Degradation of 1,5-Dioxepan-2-One

Abstract

1,5-Dioxepan-2-one was polymerized with stannous 2-ethylhexanoate as initiator and gave high molecular weight polymers, with MW > 150,000. The highest molecular weight was achieved at 110°C, and full conversion was reached after 20 hours. The polymerization rate increased with temperature. Transesterfication reactions and thermal degradation occurred above 130°C, which led to a decrease of the molecular weight. Polymerization with anion and cationic initiators led to low molecular weight polymers. Degradation of poly(1, 5-dioxepan-2-one) took place by the hydrolysis of ester bonds, and the initial molecular weight decreased by 30% during 46 weeks, starting from MW = 45,000.     

Aliphatic polyesters. III. Molecular weight and molecular weight distribution in alcohol-initiated polymerizations of ϵ-caprolactone

The effect of initiation of ?-caprolactone polymerization with mono- and polyfunctional alcohols was investigated. The resulting linear and starshaped polymers were characterized by measurement of the molecular weight and molecular weight distribution. The polymerizations were characterized by (1) rapid initiation, (2) invariance of the number of growing chains corresponding to the amount of initiator, and (3) a dominant role played by ester interchange reactions.     

聚醚酯嵌段共聚物熔体的流变性能

采用毛细管流变仪测定了组成比、聚醚分子量、熔融时间和熔融温度对嵌段聚醚酯熔体表观粘度的影响．结果发现在所研究的温度和切变速率范围内,该结构聚醚酯熔体为假塑性非牛顿流体,其粘度随聚酯段含量的增加而增加,随熔融时间增加而降低,随聚醚分子量的增大而增大．聚醚酯的零切粘度可由Ｓｐｅｎｃｅｒ Ｄｉｌｌｏｎ 公式外推得到,零切粘度对温度的依赖关系服从Ａｎｄｒａｄｅ 公式．     

Monte carlo simulation of copolymerization by ester interchange reaction in miscible polyester blends

The effects of reaction variables on the degree of randomness in copolymers formed by ester interchange reaction in miscible polyester melt blends were systematically investigated using a Monte Carlo method. Three reaction variables such as the molecular weight difference between two component polymers, the blend ratio, and the reaction ratio of end attack to bond flip, were particularly considered on the cubic lattice model. Ester interchange reactions were assumed to take place during reptational chain motions. It was found that the copolymerization was dependent upon the molecular weight difference and reaction ratio: As the molecular weight difference becomes smaller and when both end attack and bond flip reactions are involved simultaneously, the copolymerization is accelerated. However, the blend ratio does not affect the copolymerization process. This result is discussed in relation to the polymer chain conformation for the ester interchange reaction. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1637–1645, 1998     

Thermal degradation of star-shaped poly(?-caprolactone)

Thermal degradation of a serials of star-shaped poly(?-caprolactone) (PCL) with well-defined arm numbers and arm length was investigated. The weight loss of star-shaped PCL during heating process showed a two-stage character, and its dependence on molecular weight and multi-armed structure was well discussed. It was found that the thermal stability could be improved not only by increasing molecular weight but also by increasing arm numbers when the molecular weight is in a certain range. Based on the analyses of pyrolytic products by ¹H NMR and TGA-FTIR, two mechanisms of thermal degradation for the random cleavage of ester bonds of PCL chains were proposed. Ester bonds were pyrolyzed into alkene and carboxyl functional groups in mechanism I while they were pyrolyzed into ketene and hydroxyl functional groups in mechanism II. The effects of multi-armed structure of star-shaped PCL on the cleavage of ester bonds of PCL chains were discussed in terms of the limitation of central “core” on mobility of each PCL arm. Combined the results of viscosity analysis with thermal analysis, it could be concluded that both thermal stability and processability of PCL materials can be improved by controlling the multi-armed structures.     

Cationic ring‐opening polymerization of six‐membered cyclic carbonates with ester groups

This work deals with the cationic ring‐opening polymerization of the ester‐substituted cyclic carbonates 5‐methyl‐5‐benzoyloxymethyl‐1,3‐dioxan‐2‐one ( CC1 ) and 4‐benzoyloxymethyl‐1,3‐dioxan‐2‐one ( CC4 ). The polymerization was carried out with trifluoromethanesulfonic acid, methyl trifluoromethanesulfonate, boron trifluoride etherate, or methyl iodide as the initiator. The reactivity of CC1 and CC4 was higher than that of 5,5‐dimethyl‐1,3‐dioxan‐2‐one, which had no ester moiety. These results suggest that this ring‐opening polymerization was accelerated by the intramolecular ester group. CC1 showed a higher polymerizability than CC4 , affording a polymer with a higher molecular weight. Additionally, using methyl iodide as the initiator was effective for increasing the molecular weight of the obtained polycarbonate and decreasing decarboxylation. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1305–1317, 2001