含氟光引发剂的合成及其性能研究

以2-羟基-4'-(2-羟乙氧基)-2-甲基苯丙酮(Irgacure 2959)和全氟辛酰氯(PFOC)为原料合成了光引发剂全氟辛酸-2-[4-(2-羟基-2-甲基丙酰)苯氧基]乙酯(2959-F),利用红外光谱(FT-IR)和核磁共振(¹⁹F NMR)对2959-F进行了结构表征;通过紫外吸收光谱测定了2959-F的紫外吸收谱;通过实时红外光谱(RT-IR)对合成的含氟光引发剂进行了光聚合反应动力学研究,考察了光强和引发剂浓度对单体的双键转化率和聚合速率影响,并研究了光引发剂2959-F的抗氧阻聚性能.结果表明:随着光强的增大,单体的双键转化率和聚合速率增加;在一定范围内,引发剂的浓度越高,双键转化率越高,聚合速率越快.2959-F具有较高的双键转化率和较快的聚合速率,并且具有较好的抗氧阻聚性.     

可聚合二苯甲酮类光引发剂的合成及其光聚合性能研究

以4-(2,3-环氧丙氧基)二苯甲酮(EBP)和丙烯酸为原料,通过开环反应合成了含有不饱和双键的可聚合光引发剂4-(丙烯酸-2-羟基丙酯-3-氧基)二苯甲酮(AEBP).采用红外光谱(FT-IR)、核磁共振氢谱(¹HNMR)对其结构进行表征,利用紫外吸收光谱对AEBP的紫外吸收波长进行表征,通过实时红外(RT-IR)研究了AEBP引发丙烯酸酯单体的光聚合动力学.采用萃取法对比了BP与AEBP引发固化体系后的迁移性.结果表明,随AEBP浓度增加,单体最终转化率增加;当助引发剂N,N-二甲氨基苯甲酸-乙酯(EDAB)浓度为1.2%时,单体最终双键转化率最高;AEBP对双官能度单体的引发效率较之三官能度单体的好;聚合速率随光照强度的增强而变快;固化后AEBP的迁移性比传统的BP大大降低.     

大分子紫外线吸收剂的制备及其在聚偏氟乙烯中的应用

通过原子转移自由基聚合(ATRP)方法,将反应型紫外线吸收剂2-羟基-4-(3-甲基丙烯酸酯基-2-羟基丙氧基)二苯甲酮(BPMA)与甲基丙烯酸甲酯(MMA)共聚合成紫外线吸收剂P(MMA-co-BPMA),然后共混涂膜制备出具有紫外线吸收性能的聚偏氟乙烯(PVDF)复合膜。 通过核磁共振谱(NMR)、凝胶渗透色谱(GPC)、差示扫描量热仪(DSC)等技术手段对BPMA及P(MMA-co-BPMA)的结构和性能进行表征,通过紫外-可见光谱(UV-Vis)对制备的复合膜的紫外线吸收性能进行表征。 结果表明,大分子紫外线吸收剂P(MMA-co-BPMA)相对分子量分布较窄,为1.11。 当BPMA质量分数为0.68%时,P(MMA-co-BPMA)/PVDF复合膜在200~345 nm范围内透过率可降至0.4%以下,能够实现对紫外线的完全吸收。 抽提实验表明紫外线吸收剂大分子化可有效地防止外迁移。     

二苯酮-可聚合胺引发1,6-己二醇二丙烯酸酯的光聚合研究

以UV-Vis分光光度计法和Photo-DSC法分别研究了合成的3种可聚合胺类助引发剂DMPDA、EGDPM、EGMPM与二苯甲酮(BP)组成的引发体系的光化学初级过程及引发1,6-己二醇二丙烯酸酯(HDDA)的紫外光聚合动力学.考察了助引发剂胺的含量对BP的光化学初级过程和对引发HDDA光聚合动力学的影响,以及光强和温度对聚合动力学的影响.结果表明,随着胺含量的增加,BP的光化学初级反应速率增加,从而使体系的聚合反应速率增加.随着温度和光强的增加,单体最终转化率、最大反应速率增大,达到最大反应速率所需的时间减小.     

光引发常规乳液聚合制备氨基聚苯乙烯纳米粒子

采用一种简单易行的方法制备了氨基功能化的聚苯乙烯纳米粒子.首先,采用4-乙烯基苄氯与1,3-丙二胺置换反应制备了含有氨基功能基团的可聚合单体N-(3-氨基丙基)对乙烯基苄基亚胺(CVPD).然后,采用乳液聚合,以苯乙烯(St)和CVPD为共聚单体,水溶性的4-(2-羟乙氧基)苯基-(2-羟基-2-丙基)酮(Irgacure 2959)为光引发剂,十六烷基三甲基溴化铵(CTAB)为乳化剂,经紫外光辐照引发,合成了P(St-co-CVPD)二元共聚物的纳米胶乳.体系的乳化剂用量仅为体系总质量的0.1 wt%～0.8 wt%,远小于常用来制备纳米粒子的微乳液体系的乳化剂用量.用透射电子显微镜(TEM)和激光粒度分析仪(DLS)表征了P(St-co-CVPD)纳米粒子的粒径和粒径分布.用红外光谱(FTIR)和核磁共振(NMR)证明了P(St-co-CVPD)纳米粒子上氨基的存在,并通过茚三酮显色反应定量检测了氨基含量.分别研究了单体配比,引发剂浓度,乳化剂用量以及紫外光强度对反应体系的影响.实验结果表明,产物粒子尺寸为30～600 nm,氨基通过共价键连接在粒子上,其含量为1.2×10-5～1.6×10-4 mol/g.该乳液体系聚合反应速率较快,单体转化率在60 min内即可达到80%.所得粒子的氨基含量可以通过单体配比进行调节.粒子尺寸可通过单体配比,引发剂浓度,乳化剂用量以及紫外光强度进行调节.     

可聚合乳化剂合成苯乙烯-丙烯酸丁酯-α-烯烃磺酸钠共聚物乳液

以工业原料α-烯烃磺酸钠(AOS)作为可聚合乳化剂,苯乙烯(St)和丙烯酸丁酯(BA)为单体,采用预乳化种子乳液聚合合成了St-BA-AOS共聚物乳液.通过测定AOS与两种单体的竞聚率确定了半连续加料法的聚合方式.探讨了单体的加料方式、反应温度、反应时间、AOS用量等工艺条件对胶乳的影响,获得了最佳聚合条件.IR,NMR和DSC测试结果分析表明:St,BA与AOS发生了自由基共聚反应,形成的P(St-BA-AOS)共聚物结构中含有磺酸基等亲水性基团有利于乳液的稳定.在此基础上考察了AOS用量对乳液的固含量及乳胶粒粒径等的影响.结果表明:随着AOS用量的增加,乳液的固含量增加、乳胶粒的平均粒径减少.当AOS含量为2%时乳液的固含量为45.01%,平均粒径为74 nm,粒径分布指数为0.08,玻璃化温度为23.17℃.TEM测试结果显示,用相同量的AOS代替十二烷基硫酸钠可得到粒径更小和粒径分布更为均匀的乳液体系.     

乙烯基二联苯单体的螺旋选择性自由基聚合

为了深入理解乙烯基二联苯单体自由基聚合过程中的手性传递,进行了手性单体(+)-2-[(S)-异丁氧羰基-5-(4′-己氧基苯基)苯乙烯、非手性单体2-丁氧羰基-5-(4′-己氧基苯基)苯乙烯的均聚反应及它们二者的共聚反应,探讨了聚合温度和溶剂性质对手性单体均聚物旋光活性、手性单体含量对共聚物旋光活性以及聚合反应溶剂的超分子手性对共聚物旋光活性的影响.研究发现,降低聚合温度、采用液晶性反应介质有利于得到旋光度大的聚合物;少量手性单体的引入即可诱导共聚物形成某一方向占优的螺旋构象,比旋光度随手性单体的含量增加呈线性增长;在胆甾相液晶中制备的非手性单体聚合物不具有光学活性.这些结果表明,该类乙烯基二联苯聚合物具有动态螺旋构象,其光学活性主要依赖于主链的立构规整度和侧基不对称原子的手性.     

聚(碳酸酯-co-磷酸酯)的酶促合成及性能

以猪胰脂肪酶或假丝酵母皱褶酶为催化剂, 100℃下通过本体聚合成功地合成了三亚甲基碳酸酯(TMC)和2-乙氧基-2-氧-1,3-二氧磷杂环戊烷(EEP)的无规共聚物(poly(TMC-co-EEP)). 研究了酶浓度, 聚合反应时间以及共聚单体投料比等因素对共聚物分子量和产率的影响. 随着酶(PPL或CL)浓度的增加, 共聚物分子量降低. 同时, 随着EEP投料比的增加, 共聚物的分子量也降低. 共聚物数均分子量最大可达到10200. 随着共聚单体投料摩尔比(EEP/TMC)从0增加到5︰10, 共聚物的玻璃化温度从-28℃降低到-41.7℃. 体外降解实验表明: 共聚物中磷酸酯含量越高, 降解速率越快.     

曝光量对含香豆素基团的液晶共聚高分子的光控取向性能的影响

本文设计合成了含有香豆素光敏基团的单体4-(6-丙烯酰氧基己氧基)苯甲酸-7-羟基香豆素酯(M1)和一种只含液晶基元的单体4-(丙烯酰氧基)己基苯甲酸-4-甲氧基苯酚酯(M2),并将这两种单体进行自由基聚合得到了共聚物.当该聚合物薄膜置于线性偏振紫外光(LPUV)下,会发生轴选择性的光化学反应,利用动态紫外光谱(UV光谱),对所合成的共聚物的光化学性能进行了研究.结果表明:当曝光能量为1740 mJ/cm²时,光反应达到饱和,紫外吸光度将不随曝光能量的变化而变化;随着曝光能量的增加,聚合物在反应初期光反应速率比较大,当曝光能量达到500 mJ/cm²左右,光反应度已经超过50%;当曝光量达到324 mJ/cm²,各向异性ΔA达到最大,ΔA_max=0.039.     

反相乳液共聚合制备两性丙烯酰胺共聚物的研究

采用Span80-Tween80复合乳化剂和AIBA引发剂,进行丙烯酸钠(NaAA)/丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(DAC)反相乳液共聚合.研究了聚合温度、引发剂用量、单体浓度、共聚单体中DAC和AM含量、乳化剂用量及其HLB值、水/油比和水相pH值等聚合反应工艺条件或参数对聚合反应单体转化率和聚合物特性粘度的影响,聚合物特性粘度随引发剂用量和单体浓度的增大而增大的实验结果证实了该两性丙烯酰胺共聚物反相乳液制备过程中凝胶效应的存在.傅立叶红外光谱组成分析表明了两性丙烯酰胺共聚物的成功合成,扫描电镜观测乳胶粒粒径范围在0.6~8.0μm.     

Preparation and characterization of poly(MMA-M12-BPMA)/TiO2 composite particles

In this paper, poly(MMA-M12-BPMA)/TiO₂ composite particles were prepared by the copolymerization of a reactive surfactant sodium sulfopropyl-laurylmaleate (M12) and a reactive UV-stabilizer 2-hydroxy-4-(3-methacryloxy-2-hydroxylpropoxy) benzophenone (BPMA) with methyl methacrylate (MMA) in the presence of TiO₂. The structure and performance of composite particles were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, gel permeation chromatography, ultraviolet–visible absorption spectroscopy, differential scanning calorimeter, and scanning electron microscope.The measurement results indicate that the percentage of grafting and the grafting efficiency can reach 336.87% and 36.38%, respectively, and the glass transition temperature of poly(MMA-M12-BPMA)/TiO₂ composite particles is higher than that of poly(MMA-M12-BPMA); the size of the composite particles is about 130–200 nm. The poly(MMA-M12-BPMA) grafted from the surface of TiO₂ keeps the excellent characteristic of BPMA that possesses high absorbance of ultraviolet light, which is very important for improving UV-resistant performance of the polymethyl methacrylate. These research results are very useful for preparing polymethyl methacrylate with resistance to UV light.     

Synthesis and characterization of a polymerizable benzophenone derivative and its application in styrenic polymers as UV-stabilizer

In this paper, a polymerizable UV-stabilizer 2-hydroxy-4-(3-methacryloxy-2-hydroxylpropoxy) benzophenone (BPMA) was synthesized by the reaction of 2,4-dihydroxybenzophenone (UV-0) and glycidyl methacrylate (GMA), and characterized by ultraviolet-visible absorption spectroscopy (UV-Vis), Fourier transform infrared spectroscopy (FTIR) and proton nuclear magnetic resonance (¹H NMR). The results show that BPMA, with high UV-absorbing performance, has been synthesized successfully. Poly(St-co-BPMA) was prepared by emulsion copolymerization of styrene (St) and BPMA, and tested by ¹H NMR, UV-Vis, gel permeation chromatography (GPC) and differential scanning calorimeter (DSC). The results reveal that BPMA had been added to the polymer chain as copolymer and the UV-resistant performance of poly(St-co-BPMA) was enhanced significantly by the incorporation of BPMA onto the polymer chains. Poly(St-co-BPMA) was irradiated under UV light and insoluble substance, reduced viscosity, weight loss and UV-Vis absorption spectra were used to determine the degradation of poly(St-co-BPMA). The results show that BPMA is an effective UV-stabilizer in protecting poly(St-co-BPMA) from UV destroys. We also take water extraction test on poly(St-co-BPMA), PSt/UV-0 blends, and the results show that migration problem can be resolved by anchoring the UV-stabilizer onto the polymer chain.     

Studies on UV‐stability of poly(MMA‐co‐M12‐co‐BPMA)/TiO2composite particles prepared by ultrasonically initiated emulsion polymerization

In this paper, poly(methyl methacrylate‐co‐sodium sulfopropyl lauryl maleate‐co‐2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxylpropoxy) benzophenone)/TiO₂ (i.e., poly(MMA‐co‐M12‐co‐BPMA)/TiO₂) composite particles were prepared by ultrasonically initiated emulsion polymerization. To study the dispersion and UV‐stability of the composite particles, laser diffraction particle size analyzer (LDPSA), ultraviolet‐visible absorption spectroscopy (UV‐vis), UV‐vis diffuse reflectance spectroscopy (DRS), differential scanning calorimeter (DSC), and the weight loss measurement were used. The results indicate that the dispersion of the poly(MMA‐co‐M12‐co‐BPMA)/TiO₂ composite particles prepared by ultrasonically initiated emulsion polymerization is good. And the composite particles can absorb UV light; the ultraviolet absorption strength of poly(MMA‐co‐M12‐co‐BPMA) grafted onto the surface of TiO₂ has not changed after UV irradiation while that of PMMA changed significantly. The UV absorption strength, weight loss, and Tg changes are in the order PMMA> poly(MMA‐co‐M12‐co‐BPMA) >PMMA grafted onto TiO₂> poly(MMA‐co‐M12‐co‐BPMA) grafted onto TiO₂. These results show that the ultrasonically initiated emulsion polymerization will enhance the UV stability of composite particles, and the UV‐stability of PMMA can be enhanced by the introduction of the organic UV‐stabilizer BPMA and the inorganic UV‐stabilizer titanium dioxide into the PMMA chains by covalent bond, and the effect of the BPMA and the TiO₂ used together is better than that used, respectively. Copyright © 2009 John Wiley & Sons, Ltd.     

Emulsion copolymerization of styrene with acrylic or methacrylic acids – distribution of the carboxylic group

Studies on batch emulsion copolymeization of styrene with acrylic acid (AA) or methacrylic acid (MAA) were carried out. The effect of AA or MAA on the total conversion of the monomers was studied by a gravimetric method. The distribution of the carboxylic group in the copolymer microspheres was investigated by X-ray photoelectron spectroscopy and elemental analysis. The surface content of the carboxylic groups of styrene (St)/AA copolymer microspheres was found to be higher than that of St/MAA copolymer microspheres. The effects of partial neutralization of MAA in emulsifier-free emulsion copolymerization and seeded emulsion copolymerization on the distribution of the carboxylic group was also investigated. Received: 14 December 1999/Accepted: 23 August 2000     

Monomer-isomerization polymerization. XXI.. Monomer-isomerization copolymerization of 3-methyl-1-butene and 2-pentene with ziegler–natta catalyst

3-Methyl-1-butene (3M1B) was found to undergo monomer-isomerization copolymerization with 2-pentene (2P) in the presence of Ziegler–Natta catalyst to give a copolymer exclusively consisting of 3M1B and 1-pentene (1P) units, the same as that obtained from copolymerization of 3M1B and 1P. The apparent copolymerization parameters were determined. The amount of 3M1B unit incorporated in the copolymers was found to increase in the copolymerization system of 3M1B-2P more than in that of 3M1B-1P. The polymers consisting of nearly complete 3M1B units were produced at a rapid rate through monomer-isomerization copolymerization of 3M1B with 2P in the presence of TiCl₃ ? (C₂H₅)₃Al catalyst.     

含氟丙烯酸酯共聚乳液及其膜表面特性的研究

以十二烷基硫酸钠 (SDS)和OP 10混合乳化剂 ,制备了甲基丙烯酸全氟辛基乙酯 (FMA8) 甲基丙烯酸丁酯 (BMA) 甲基丙烯酸 (MAA)共聚乳液 .通过DSC、FT IR、1 H NMR对共聚物的结构、组成进行了表征研究 .采用JZHY 180界面张力仪研究了共聚乳液膜表面的性质 ,结果表明 ,随着共聚物中全氟单体含量的增加 ,共聚物膜的表面能显著降低 ,当全氟单体的含量达到 2 5wt %时 ,其表面能降低到 19 74mJ m2 .X ray光电子能谱(XPS)对共聚物表面原子组成的分析结果表明 ,共聚物表面氟的含量远高于其平均含量 ,证明了含氟基团的趋表现象 .经退火处理 ,共聚物膜表面的氟含量增加 ,表面自由能降低     

Preparation of sulphonate-containing polymer particles <Emphasis Type="Italic">via</Emphasis> semi-continuous emulsion copolymerizaion of styrene and sodium styrene sulphonate

Submicron-sized P(St-NaSS) latexes were prepared via a semi-continuous emulsion copolymerization of styrene (St) and sodium styrene sulphonate(NaSS) in the presence of anionic surfactant,in which NaSS aqueous solution and St were separately dropwise charged into the polymerization system at the same time.The hydrodynamic diameter of the latex particles was measured by dynamic light scattering(DSL) method,and the NaSS unit content of the purified copolymer by water extraction was calculated based on the elementary analysis.Results showed that the copolymerization could be performed smoothly with the monomer conversion more than 96%in the absence of crosslinker,and PNaSS homopolymer could be removed from the latex product by water extraction for 28 h.The weight loss in the water extraction tended to decrease and the NaSS unit content of the purified copolymer tended to increase with the increase of monomer feeding time, and both of them increased with the increase of NaSS/St mole ratio in the charge.The introduction of divinyl benzene (DVB) could decrease the weight loss in the water extraction and increase the NaSS unit content of the purified copolymer. When 25/75 mole ratio of NaSS/St and 11 mol%DVB of total NaSS and St were used in the recipe,and the monomer feeding time was 3 h in copolymerization,the NaSS unit content of the purified copolymer reached 7.31 mol%.     

甲基丙烯酸环氧丙酯共聚物乳液的研究

研究了以甲基丙烯酸环氧丙酯作为活性单体，采用种子乳液聚合制备四元体系的核—壳结构共聚物乳液，用透射电子显微镜观察了乳胶粒的微观形态，并对其稳定性、流变性等进行了测试，考察了甲基丙烯酸环氧丙酯及其含量对乳液性能的影响．     

苯乙烯-苯乙烯磺酸钠共聚物的制备及其流变性能

采用乳液聚合合成了一种可作为聚丙烯(PP)纤维可染改性添加剂的苯乙烯-苯乙烯磺酸钠共聚物P(St-co-NaSS)。通过傅里叶转换红外光谱仪(FT-IR)和核磁共振氢谱仪(~1 H-NMR)对共聚物的苯乙烯磺酸钠结构单元进行了表征,研究了反应条件对共聚物磺化度的影响;通过差示扫描量热仪(DSC)和热重分析仪(TG)研究了磺酸基团的引入对共聚物的玻璃化转变温度和起始分解温度的影响;通过旋转流变仪研究了磺化度对共聚物剪切黏度的影响;初步探讨了PP/P(St-co-NaSS)共混体系的染色性能。结果表明:当反应时间为2h,反应温度为70℃,引发剂质量分数为0.6%,苯乙烯磺酸钠的摩尔分数为0.01时,共聚物的磺化度f=6.68%(零切黏度η0=19 620Pa·s,属牛顿流体);在10~(-2)~10~(-1) s~(-1)的剪切速率范围内,P(St-co-NaSS)表现出假塑性流体的特征,具有较好的加工流动性。对于PP/P(St-co-NaSS)共混体系,使用阳离子染料染色时,染色深度(K/S值)为2.603 2,使用分散染料染色时,K/S值为10.168 8。P(St-co-NaSS)适合作为聚丙烯纤维的可染改性添加剂。