Simultaneous Spectrophotometric Determination of Aluminum and Iron in Micellar Media by Using the H‐Point Standard Addition Method

A very simple spectrophotometric method for simultaneous determination of aluminum(III) and iron(III) based on formation of their complexes with pyrocatechol violet (PCV) in micellar media, using the H‐point standard addition method (HPSAM), is described. In micellar media, the metal complexes of Al‐PCV and Fe‐PCV are formed very fast. Formation of both of the complexes was complete within 5 min at pH 8.5. The linear ranges for aluminum and iron were 0.05‐2.50 and 0.10‐4.00 μg mL^?1, respectively. The relative standard deviation (R.S.D.) for the simultaneous determination 0.40 μg mL^?1 of Al(III) and 0.20 μg mL^?1 of Fe(III) were 3.24% and 4.22%, respectively. Interference effects of common anions and cations were studied. The method was applied to simultaneous determination of Al(III) and Fe(III) in standard reference material and alloy samples.     

Extraction behavior of Tm(III), Dy(III) and Sm(III) lanthanide with N-benzoyl-N-phenylhydroxalamine

The extraction of Sm(III), Dy(III) and Tm(III) with N-benzoyl-N-phenylhydroxalamine (BPHA) in benzene at pH range (1–10) has been studied. Quantitative separation was found in borate media at pH 8. The slope analysis showed that the extracted complex was M(BPHA)₃, where M=Sm(III), Dy(III) and Tm(III). The effect of various masking agents indicated that EDTA, oxalate, fluoride, phosphate and citrate, interfered in this study. Decontamination study showed that Cu(II), Zn(II), Ni(II), Co(II), Cr(III), Sc(III) and Fe(III) had very poor separation factors, whereas Sn(II), Cd(II), In(III), Ru(II), Hg(II), Ag(I), Ta(V) and Hf(IV) had very large separation factor. The effect of different diluents showed that carbontetrachloride, chloroform, benzene, toluene, nitrobenzene dichloromethane, MIBK and cyclohexanone were equally good for extraction except TBP due to ion association.     

Iron(III) as releasing agent for copper interference in the determination of selenium by hydride-generation atomic absorption spectrometry

Iron(III0 has a very effective releasing effect on the depressive interference from copper(II) on the determination of selenium by hydride-generation atomic absorption spectrometry. In solutionwith 100 mg 1^?1 Cu(II), 10 μg 1^?1 Se(IV) and 2.0 mol l^?1 HCl, the absorbance obtained was much higher when 8 g 1^?1 Fe(III) was added than for any earlier releasing agent.     

氯冉酸阴离子桥联的Nd(III)-Nd(III), Dy(III)-Dy(III)和 Ho(III)-Ho(III)双 核配合物的合成与磁性

本文合成了三个以氯冉酸阴离子为桥基的稀土双核配合物,Ln~2(Phen)~4(CA)(NCS)~4(Ln=Nd,Dy,Ho;Phen=菲咯啉;CA=氯冉酸二价阴离子)。通过元素分析,红外光谱,电导,电子吸收光谱及变温(4-300K)磁化率表征了配合物,并由变温磁化率观察到的数据和理论方程通过最小二乘法拟合,得出分子内稀土离子间的相互作用参数:Z'J'=-0.79(Nd),-0.67(Dy),-0.63cm^-^1(Ho);表明稀土离子间存在极弱的反铁磁性交换相互作用。零场分裂参数Δ=-0.16(Nd),-0.76(Dy),-2.55cm^-^1(Ho);g=0.618(Nd),1.739(Dy),1.601(Ho),拟合因子≈10^-^4。     

Direct heterometric micro-determination of zinc with quinaldic acid in the presence of other metals

0.001–0.005M solutions of zinc salts (1–5 mg Zn in io ml) which contain more than 95% of foreign metal as Mg, Ca, Ba, Mn.(II), Fc(III), Al or Cr(III), may be titrated hctcrometrically with an error of ? 1%. The titrated zinc solution may contain an excess of Cd (85%). The analysis with Ni or Co is very limited.     

Reversed-phase HPLC separation of complex mixtures of trace metals as dibenzyldithiocarbamate chelates

The dibenzyldithiocarbamate chelates of Cd(II), Pb(II), Bi(III), Hg(II), Ni(II), Cu(II), As(III), Fe(III), Co(III) and In(III) are separated by reversed-phase HPLC in isocratic conditions. The procedure is simple, rapid, and gives satisfactory separations with high efficiency and sensitivity at mobile phase compositions very rich in organic modifier (85-88% CH(3)CN). The detection limits range from 1.4 to 14 mug/1. The elution order is correlated with the ability of the central metal atom to affect the electronic distribution of the ligand, which has readily polarizable donor atoms. Infrared spectroscopy data corroborate this assumption.     

Arsenic(III) sorption on nanostructured cerium incorporated manganese oxide (NCMO): a physical insight into the mechanistic pathway

Arsenic(III) sorption was investigated with nanostructured cerium incorporated manganese oxide (NCMO). The pH between 6.0 and 8.0 was optimized for the arsenic(III) sorption. Kinetics and equilibrium data (pH=7.0±0.2, T=303±1.6 K, and I=0.01 M) of arsenic(III) sorption by NCMO described, respectively, the pseudo-second order and the Freundlich isotherm equations well. The sorption process was somewhat complicated in nature and divided into two different segments, initially very fast sorption followed by slow intraparticle diffusion process. Sorption reaction of arsenic(III) on NCMO was endothermic (ΔH°=+13.46 kJ mol(-1)) and spontaneous (ΔG°=-24.75 to -30.15 kJ mol(-1) at T=283-323 K), which took place with increasing entropy (ΔS°=+0.14 kJ mol(-1)K(-1)) at solid-liquid interface. Energy of arsenic(III) sorption estimated by analyzing the equilibrium data using the D-R isotherm model was 15.4 kJ mol(-1), indicating the ion-exchange type mechanism. Raman, FT-IR, pH effect, desorption, etc. studies indicated that arsenic(III) was oxidized to arsenic(V) during the sorption process.     

Determination of trace molybdenum in vegetable and food samples by spectrophotometry with p-carboxyphenylfluorone

A new highly sensitive and selective chromogenic reagent, p-carboxyphenylfluorone (p-CPF), was studied for spectrophotometric determination of trace molybdenum. In 0.36 mol L(-1)phosphoric acid medium, p-CPF reacts with molybdenum(VI) to form a 1:3 red complex, which has a sensitive absorption peak at 531 nm. Under optimal conditions, the reaction of molybdenum(VI) with p-CPF completed rapidly and absorbance remains almost constant for at least 24 h. Molybdenum(VI) obeyed Beer's law in the range 0-2.0 microg mL(-1); the apparent molar absorption coefficient, Sandell's sensitivity and the limit of detection were found to be 1.03 x 10(5) L mol(-1) cm(-1), 1.028 ng cm(-2)and 0.73 ng mL(-1) respectively; the effect of various foreign ions were examined in detail. It was found that most coexisting ions can be tolerated in considerable amounts, especially 800 mg of Mn(II), 200 mg of Mg(II), Fe(II), Co(III), Ni(II) and Cd(II), 50 mg of Ca(II) and Al(III), 25 mg of Cu(II) and Fe(III), 10 mg of Hg (II), La(III), Bi(III), Pb(II) and Zn(II) don't interfere with the determination of molybdenum(VI). The proposed method is very simple, sensitive and selective, it has been applied to determine molybdenum in vegetable and food samples with a very high precision and accuracy. Moreover, the synthesis of the reagent and the conditions of the colour reaction were also studied in detail.     

Discrimination of nitroxyl and nitric oxide by water-soluble Mn(III) porphyrins

The water-soluble manganese(III) meso-tetrakis (N-ethylpyridinium-2-yl) porphyrin (Mn(III)TEPyP) and manganese(III) meso-(tetrakis(4-sulfonato-phenyl)) porphyrinate (Mn(III)TPPS) are able to chemically distinguish between HNO and NO donors, reacting with the former in a fast, efficient, and selective manner with concomitant formation of the {MnNO}(7) complex (k(on(HNO)) approximately equal to 10(5) M(-1) s(-1)), while they are inert or react very slowly with NO donors. DFT calculations and kinetic data suggest that HNO trapping is operative at least in the case of Mn(III)TPPS, while catalytic decomposition of the HNO donors (sodium trioxodinitrate and toluene sulfohydroxamic acid) seems to be the main pathway for Mn(III)TEPyP. In the presence of oxygen, the product Mn(II)TEPyP(NO) oxidizes back to Mn(III)TEPyP, making it possible to process large ratios of nitroxyl donor with small amounts of porphyrin.     

Ion chromatography of chloro complexes of the platinum group metals and gold using bonded phase silica substrates

The ion chromatography of chloro complexes of Au(III), Ir(IV), Ir(III), Os(IV), Pd(II), Pt(IV), Rh(III) and Ru(III) was investigated using anion-exchange and ion-interaction techniques involving silica-based phases. Chloride was either absent or at a very low level and the pH was high enough to enable steel-fabricated liquid chromatography equipment to be used. With anion exchange, Ir(IV), Ir(III), Os(IV) and Pt(IV) gave good stable chromatography and all produced linear calibration plots, except Ir(IV) owing to instability of the sample solution. The detection limits were Ir(III) 5, Os(IV) 10 and Pt(IV) 2 ng ml^?1. The ion-interaction technique was not so successful, only Au(III) and Pd(II) giving stable chromatography. The calibration plots were slightly curved, although acceptable, and the detection limits were 10 and 30 ng ml^?1 for Au (III) and Pd(II), respectively.     

Simple conditions for the use of ferroin indicator in cerimetric titrations of antimony(III) alone and in mixtures with arsenic(III)

The titration of antimony(III) with cerium(V) sulphate in the presence of ferroin indicator at room temperature is entirely satisfactory in media consisting of 50% ($\text{v}\text{v}$) acetic acid and 1–3 M hydrochloric acid. In the absence of acetic acid, ferroin reacts with the antimony(V) formed in the very early stages, to give a sparingly soluble red complex, which remains in suspension and resists oxidation by cerium(IV). This titration provides a rational method for sequential visual titrations of antimony(III) and arsenic(III). The composition of the ferroin-antimony(V) complex is discussed. Titrations of antimony(III) in 0.5–1 M sulphuric acid medium do not require acetic acid but need iodine monochloride catalyst.     

Spectroscopic studies of aluminum and gallium complexes with oxalate and malonate in aqueous solution

The local structures of Ga(III) in aqueous oxalate and malonate complexes were studied by means of Ga K-edge EXAFS spectroscopy. Irrespective of the number and type of coordinated ligands, the EXAFS results showed very regular first coordination shells consisting of six oxygen atoms. Scattering paths from more distant atoms revealed that both oxalate and malonate form mononuclear chelate structures where one oxygen from each carboxylate group binds to Ga(III). Again, very little variation in bond distances and no changes in coordination modes were detected as the number of ligands coordinated to Ga(III) was varied. Based on the very close resemblance of IR spectra of oxalate and malonate complexes of Al(III), and the corresponding complexes of Ga(III), it is believed that the local structures of the Al(III) complexes are similar to those of the Ga(III) complexes in terms of ligand coordination modes and distortions. This conclusion was corroborated by results from theoretical frequency calculations.     

Sensitive spectrofluorimetric determination of aluminium(III) with Eriochrome Red B

A spectrofluorimetric method is reported for the determination of Al(III), based on the formation of a fluorescent Al(III)-Eriochrome Red B complex in the presence of hexamethylenetetramine at 60°C. Fluorescence measurements were made at 2°C and all variables that affect the development of the complex are reported. The method is very selective and the detection limit is 0.1 ng ml^?1. It was applied to the determination of Al(III) in tap water.     

X-ray structures and homolysis of some alkylcobalt(III) phthalocyanine complexes

The first crystallographic data for sigma-bonded alkylcobalt(III) phthalocyanine complexes are reported. A single-crystal X-ray structure of CH(3)CH(2)Co(III)Pc (Pc = dianion of phthalocyanine) reveals that the solid consists of centrosymmetric face-to-face dimers in which the CH(3)CH(2)Co(III)Pc units retain their square pyramidal geometry. The structure appears to be the first one reported for a five-coordinate RCo(III)(chelate) complex with an electron-deficient equatorial system. The Co-C bond in CH(3)CH(2)Co(III)Pc (2.031(5) A) is the longest found in five-coordinate RCo(III)(chel) complexes (R = simple primary alkyl group). Another X-ray study demonstrates that CH(3)Co(III)Pc(py) has a distorted octahedral geometry with axial bonds of very similar length to those in methylcobalamin. The axial bonds are shorter than those in its octaethylporphyrin analogue, in accordance with a weaker trans axial influence in six-coordinate complexes containing an electron-deficient phthalocyanine equatorial ligand. A different trend has been observed for five-coordinate RCo(III)(chel) complexes: electron-rich equatorial systems seem to make the Co-C axial bond shorter. Kinetic data for the homolysis of RCo(III)Pc complexes (R = Me, Et) in dimethylacetamide are also reported. Homolysis of ethyl derivatives is faster. The Co-C bond dissociation energies (BDEs) for the pyridine adducts of the methyl and the ethyl derivative are 30 +/- 1 and 29 +/- 1 kcal/mol, respectively. The BDE for CH(3)CoPc(py) is considerably lower than that for MeCbl despite the very similar lengths of the axial bonds in the two complexes. The results of this work do not support any correlation between the Co-C bond length and the bond strength as defined by BDE.     

Screening structure-property correlations and device performance of Ir(III) complexes in multi-layer PhOLEDs

The structure-property correlations of a set of heteroleptic red- and green-emitting Ir(III) complexes with different temperature sensitivities and charge trapping capabilities are described, revealing superb performance in multi-layer phosphorescent organic light-emitting diodes (PhOLEDs) expressed by very high maximum luminous efficiencies up to 36.8 cd A(-1). Using 2-phenylpyridine and with 2-(naphthalen-1-yl)pyridine as the C^N ligand, the resulting red emitting complex featured a maximum luminous efficiency of 10.8 cd A(-1); one of the most excellent device performances within this class of red Ir(III) emitters.     

{W48} ring opening: Fe16-containing, Ln4-stabilized 49-tungsto-8-phosphateopen wheel [Fe16O2(OH)23(H2O)9(P8W49O189)Ln4(H2O)20]11-

Wheely: For the first time and very unexpectedly, a rupture of the very stable {P(8)W(48)} wheel was observed in aqueous solution at pH?4 and 80?°C in the presence of Fe(III), Eu(III)/Gd(III), and H(2)O(2). This inorganic ring opening is unprecedented in polyoxometalate chemistry.     

Reduction of iridium in solution

Iridium(IV) in solution may be reduced to metal via the intermediate Ir(I). Reduction of Ir(III) has not been detected. The current efficiency for metal deposition is low because: (1) The (IV)-(I) reduction is competing with the (IV) to (III) reduction, and hydrogen evolution in aqueous solution. (2) Ir(I) is very easily oxidised to (III), even by hydrogen. (3) Some iridium salts are not stable in the (IV) state (e.g. triaquotrichloroiridate in molar chloride).     

New methods for the preparation of 1-phenyl-trans-cyclohexane-1,2-diol

In contrast with previous reports, it was found that the reaction of 1-phenylcyclohexene with peroxyformic acid is not entirely stereospecific, but gives some trans-1-phenylcyclohexane-1, 2-diol (IV) beside the cis-isomer (III). The reaction of 1-phenylcyclohexene oxide (II) with formic acid yielded a similar mixture of III and IV, while addition of trichloroacetic acid in benzene was entirely cis-stereospecific. Reaction of the epoxide II with potassium hydroxide took place only under very drastic conditions to give a small yield of III, while sodium 2-dimethylaminoethoxide added exclusively in a trans way, leading to the amino ether X, which was easily transformed into the trans-glycol IV. The latter compound was also the main product of the borohydride reduction of 2-hydroxy-2-phenylcyclohexanone (IX). Possible explanations of the observed stereochemical results are discussed.     

Separation and determination of some trivalent metal ions using rhodamine B grafted polyurethane foam

The incorporation of rhodamine B into polyurethane foam matrix was prepared by mixing the rhodamine B with polyol (polyether) prior to the addition of diisocyanate reagent to form the polyurethane foam material. Rhodamine B grafted polyurethane foam (Rod.B-PUF) was found to be very suitable for the separation and preconcentration of trivalent metal ions e.g. bismuth (III), antimony (III) and iron (III) from thiocyanate solutions. Bismuth and antimony were separated from concentrated acid medium (1–6 M H₂SO₄). Iron (III) was separated from pH 1 to 3. The kinetics of sorption of the Bi (III), Sb (III) and Fe (III) onto the Rod.B-PUF was found to be fast, the extraction is accomplished from 5 to 10 min with average values of half-life of sorption (t_1/2) of 2.9 min. The average values of the Gibbs free energy (ΔG) for the sorption of metal ions onto Rod.B-PUF are ?6.6 kJ mol^?1, which reflect the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Rod.B-PUF was also discussed.