Determination of poly(3-hydroxybutyrate) using a combination of enzyme-based biosensor and alkaline hydrolysis.

The combination of an enzyme-based biosensor and alkaline hydrolysis was developed for the measurement of poly(3-hydroxybutyrate) (PHB). The principle of the determination is based on that the alkaline condition converts PHB to produce its monomer, 3-hydroxybutyrate (3-HB), which generates a detectable current signal by an amperometric biosensor through coupled two-enzyme reactions on an electrode. This method takes less than 40 min, and results in a linear detection range of 0.5-110 mg L-1 PHB with a detection limit of 0.3 mg L-1 by the saturated production of 3-HB; it can also take less than 15 min and result in a linear detection range of 1.0-160 mg L-1 PHB with a detection limit of 0.5 mg L-1 by a part production of 3-HB. The method also shows simple operation and high reproducibility.     

Operational parameters of voltammetric high-performance liquid chromatographic detectors with copper electrodes and application to a determination of some fodder biofactors

Two versions of an amperometric detector with a copper working electrode have been constructed and tested for high-performance liquid chromatography (HPLC). The performance of the detectors was studied using selected amino acids. The dependence of the detector response on the mobile phase flow-rate was studied in the range common in both macro- and microcolumn HPLC (5 microliter/min to 1.0 ml/min). It has been found that the detection sensitivity generally increases with decreasing flow-rate, i.e., the detector response is governed by the rate of the complexation reaction between the cupric ions and the solutes. This fact makes amperometric detection with a copper electrode especially useful for microcolumn separations. For all 20 amino acids studied, calibration curve parameters and detection limits have been determined; the latter vary from 0.4 to 18 ng in the injected volume. The amino acids can also be sensitively detected in a medium of 0.1-1.0 M ammonia, which is promising for the use of strong anion exchangers in amino acid separations. Choline can also be detected at a copper electrode, with a detection limit of 40 ng. An HPLC method with amperometric detection at a copper electrode has been developed for the determination of lysine, methionine and choline in fodder biofactors.     

离子色谱法测定大肠癌患者尿液中的甘露醇和乳果糖

建立了大肠癌患者尿液中甘露醇和乳果糖的高效阴离子交换分离-脉冲积分安培(HPAEC-PAD)检测方法.样品经稀释、净化、过滤后进行色谱分析,采用Carbopac PA1(250 mm×4mm)阴离子交换柱分离,以NaOH-乙酸钠梯度淋洗液为流动相,流速1.0 mL/min,脉冲积分安培检测器(PAD)检测,外标法定量.结果表明,甘露醇和乳果糖的的线性范围为0.2～20 mg/L,相关系数分别为0.9995和0.9998,回收率为91.7％～102.6％,相对标准偏差均小于2.1％,检出限为0.05和0.06 mg/L(S/N=3).本方法前处理简便、灵敏度高、重现性好,可用于大肠癌患者尿液中的甘露醇和乳果糖的测定.     

Simultaneous determination of copper, cadmium and nickel by ratio derivative polarography

Ternary mixtures of metals can be resolved by using the ratio derivative polarography without the need for any pre-separation step. The method is based on the simultaneous use of the first derivative of ratios of polarograms and measurements of zero-crossing potentials. The polarogram of the mixture is obtained and the amplitudes of the current at appropriate potentials are divided by the corresponding amplitudes in the polarogram of a standard solution of one of the components, and the subsequent derivation against potential results to the first derivative of the ratio polarogram. The concentrations of the other two components are then determined from their respective calibration graphs established by measuring the ratio derivative analytical signal at the selected zero-crossing points. The method has been successfully applied for resolving ternary mixtures of copper, cadmium and nickel, which have overlapped polarograms in pH 2.87 Britton-Robinson buffer. The concentration ranges to be determined are 0.30-1.40 mg l(-1) for copper, 0.90-4.50 mg l(-1) for cadmium and 0.20-1.20 mg l(-1) for nickel, and the recoveries are 88.3-101.9% for copper, 92.2-105.4% for cadmium and 95.0-107.0% for nickel.     

高效离子交换色谱-电化学检测法测定药物合成中间体中的6-磷酸甘露糖

在制备6-磷酸甘露糖过程中,将6-磷酸甘露糖与磷酸根杂质分开是纯化过程和建立质量标准的重要环节。本文建立了6-磷酸甘露糖和磷酸根的离子色谱分离-电化学检测方法。样品经溶解、过滤后进行色谱分析,以IonPac AG18离子交换柱(50 mm×4 mm)为保护柱,在Ionpac AS18离子交换色谱柱(250 mm×4 mm)上分离,以25 mmol/L氢氧化钾溶液为流动相,等度淋洗,流速1.0 mL/min,安培检测器和电导检测器串联检测,外标法定量。先使用安培检测器检测,在碱性条件下,6-磷酸甘露糖在安培检测器上被选择性检出;后使用电导检测器检测,经ASRS型抑制器抑制背景电导后,6-磷酸甘露糖和磷酸根同时被电导检测器检出,二者分离度良好。采用安培检测器检测时,进样量为25 μL, 6-磷酸甘露糖的线性范围为0.06～10.00 mg/L,相关系数为0.9998,回收率为92.1%～103.1%,相对标准偏差均小于3%,检出限(以信噪比为3计)为0.02 mg/L。该方法灵敏度高,无杂质干扰,前处理简便,可用于原料药合成中间体的检测,结果令人满意。     

Amperometric determination of thioacetamide with copper(I)

A method is given for the amperometric determination of thioacetamide (TAA) based on the reaction of TAA with copper(I) in ammoniacal solution. The reduction current due to the copper(I) is used to determine the end-point. The determination is carried out at constant temperature (25°), pH 8.0-9.8 (ammonia-urotropine buffer), and at constant potential (−0.6 V vs. S.C.E.), with a dropping mercury electrode as cathode and a saturated calomel electrode as anode. The solution is deaerated by a stream of electrolytically generated hydrogen. The titrations are carried out simply and rapidly and the results are fairly reproducible. The error is generally 1.0% for amounts of TAA ranging from 0.07 to 1.8 mg.     

Biosorption of nickel(II) and copper(II) ions from aqueous solution by Streptomyces coelicolor A3(2)

The biosorption of nickel(II) and copper(II) ions from aqueous solution by dried Streptomyces coelicolor A3(2) was studied as a function of concentration, pH and temperature. The optimum pH range for nickel and copper uptake was 8.0 and 5.0, respectively. At the optimal conditions, metal ion uptake was increased as the initial metal ion concentration increased up to 250 mg l(-1). At 250 mg l(-1) copper(II) ion uptake was 21.8% whereas nickel(II) ion uptake was found to be as high as 7.3% compared to those reported earlier in the literature. Metal ion uptake experiments were carried out at different temperatures where the best ion uptake was found to be at 25 degrees C. The characteristics of the adsorption process were investigated using Scatchard analysis at 25 degrees C. Scatchard analysis of the equilibrium binding data for metal ions on S. coelicolor A3(2) gave rise to a linear plot, indicating that the Langmuir model could be applied. However, for nickel(II) ion, divergence from the Scatchard plot was evident, consistent with the participation of secondary equilibrium effects in the adsorption process. Adsorption behaviour of nickel(II) and copper(II) ions on the S. coelicolor A3(2) can be expressed by both the Langmuir and Freundlich isotherms. The adsorption data with respect to both metals provide an excellent fit to the Freundlich isotherm. However, when the Langmuir isotherm model was applied to these data, a good fit was obtained for the copper adsorption only and not for nickel(II) ion.     

Amperometric titration of palladium, silver and copper with benzimidazol-2-ylmethanethiol, and its application to non-ferrous materials

A method is described for the determination of mg amounts of palladium, silver and copper by amperometric titration with benzimidazol-2-ylmethanethiol in acetate buifer medium (pH 4-5) at an applied potential of -0.2 V vs. the saturated calomel electrode. Direct titrations are possible in the presence of a number of foreign ions. Copper and palladium interfere mutually and in the determination of silver. Mercury(I), mercury(II) and platinum(IV) also interfere. Silver does not interfere in the determination of copper and palladium if it is first precipitated as chloride. The method has been successfully applied to the analysis of non-ferrous materials.     

Amperometric determination of copper with mandelamidoxime

Summary A rapid method for the amperometric determination of copper with mandelamidoxime is described. About 0.5–8.0 mg copper(II) at a concentration of ca. 0.8–3.2 mM can be determined with accuracy (error less than ± 1%) in an ammonium chloride — ammonia buffer medium using a simple manual apparatus with a microammeter (0–50 A) of large scale for measuring the current. Direct titration of copper is possible only in the presence of cadmium while in the presence of all other commonly associated elements preliminary separation is necessary.Formerly: Research Officer, Department of Inorganic & Analytical Chemistry, Indian Association for the Cultivation of Science, Calcutta-32, India     

火焰原子吸收光谱法连续测定陶瓷绝缘子镀液中的锌、铜、铁

采用火焰原子吸收光谱法进行镉镍电池陶瓷绝缘子镀液中锌、铜、铁含量的连续测定。在优化条件下．该方法灵敏度高，干扰小，选择性和重现性好，步骤简单，操作容易，分析周期短。测定结果的相对标准偏差均小于1．0％，加标回收率为97．0％～99．0％。该法适用于镉镍电池陶瓷绝缘子镀液中锌、铜、铁含量的现场控制分析和样品系统分析。     

Precipitation of metal-cupferron complexes from homogeneous solution-I: determination of copper

The cupferron complex of copper has been precipitated from homogeneous solution by the addition of phenylhydroxylamine and sodium nitrite to a cold, acidic solution containing copper(II) ions. The precipitate can be dried at 90 +/- 5 degrees and weighed without ignition to the oxide. Less than 3 mg of copper can be determined. A fairly high concentration of acetic acid is tolerable. Separation from large quantities of zinc, nickel and silver has been achieved.     

Catalytic cathodic stripping voltammetry of oxidized glutathione at a hanging mercury drop electrode in the presence of nickel ion

Oxidized glutathione (GSSG) can be determined after previous accumulation on the HMDE at E > -0.2 V (vs. the Ag AgCl reference electrode). GSH is formed during the accumulation, possibly by a mercury-ion-assisted hydrolytic disproportionation of GSSG. In the subsequent cathodic scan GSH is released and catalyses the reduction of nickel ion, giving a peak located at -0.6 V. This enables the determination of GSSG by differential-pulse cathodic stripping voltammetry at pH 7.0 in the phosphate acetate or MOPS buffer containing 0.5-1.0 mM Ni(II). The detection limit is 10 nM. The calibration graph is linear even in the presence of small amounts of human serum albumin, HSA. However, HSA increases the detection limit (20 nM for 3 x 10(-4)% HSA). Acetyl-cysteine in small excess or Cu(II) present as reagent impurity do not interfere. Glutathione, cysteine and similar compounds, which accumulate as mercury salts and form stable nickel complexes, will interfere. The method is put forward as a novel alternative stripping voltammetric method to those involving accumulation and determination as mercury or copper salts and complexes, in the knowledge that it may have advantages in particular analytical situations. In particular the method discriminates against compounds which accumulate as mercury salts but which do not form stable nickel complexes.     

Cathodic stripping voltammetric determination at a hanging mercury drop electrode of the environmental heavy metal precipitant trimercapto-s-triazine (TMT)

Trimercapto-s-triazine (TMT) is available commercially for precipitating heavy metals in effluents prior to discharge and for recovering silver and copper. The TMT content of an effluent for discharge is normally monitored down to about 2 ppm by means of its UV absorption at 285 nm. Indirect cathodic-stripping voltammetric methods of determining TMT at sub-ppb levels in standard solutions are reported here. These methods might prove suitable for the determination of TMT in effluent at levels lower than is currently possible. TMT can be accumulated and determined indirectly at pH 9.0 as its mercury salt down to sub-ppb levels. Accumulation is made at 0 V and the mercury TMT reduction peak is at -0.47 V. Alternatively, by adding nickel(II), TMT can be determined optimally at pH 7.8, using the catalytic nickel peak at -0.73 V and accumulating between -0.10 and -0.60 V: at this pH the HgTMT peak at -0.47 V is small. At slightly higher pH (pH 8.6) the nickel TMT complex can be accumulated directly at -0.40 V, but at this pH, however, a slightly increased sensitivity can be achieved by accumulating TMT as its mercury salt, at -0.1 V in the presence of nickel(II), the nickel TMT complex being formed during the potential sweep on the release of the TMT when the mercury salt is reduced. Unlike many other thiols TMT is not accumulated as its copper(I) salt on addition of copper(II) to the solution.     

连续滴定法测定铅精矿中的铅、铜

建立了铅精矿中主量元素铅和次量元素铜的连续滴定分析方法。将铅滴定分析中经硫酸沉淀分离后的滤液,再经硫酸冒烟,用去离子水溶解后,通过滴定法对铅精矿中高含量铜进行分析。该方法铅精矿中铅的检出限为1.4 mg/g,铜的检出限为1.0 mg/g。对3个实际样品中铅、铜分别进行测定,测定结果的相对标准偏差均小于3.0%(n=7),铅的加标回收率为99.71%~100.19%,铜的加标回收率为99.33%~100.47%。该方法通过一次溶样,对铅精矿中的铅、铜连续进行滴定分析,方法快速、准确,适用于铅精矿中含量大于1.4%的铅和含量大于1.0%的铜的测定。     

A rapid solid sampling method for determination of nickel and copper along human hair by ETAAS

A procedure for copper and nickel determination in scalp hair by solid sampling electrothermal atomic absorption spectrometric method was described. The hair samples (0.02 to 0.4 mg) were inserted directly on the platforms of solid sampling autosampler. The effects of pyrolysis temperature, atomization temperature, the amount of sample as well as addition of a modifier (Pd/Mg) and/or auxiliary digesting agents (hydrogen peroxide and nitric acid) and/or a surfactant (Triton X-100) on the determination of copper and nickel by solid sampling atomic absorption spectrometry were investigated. After optimization of parameters, the average recoveries of copper in two different certified reference hair samples were 105.7 and 97.6%. The recoveries of nickel in the both certified reference hair samples were in 95.2 and 96.4%. The limits of detection (3σ, N = 10) for copper and nickel were 22 ng/g and 35 ng/g, respectively. Heterogenous distribution of analyte in microscale for segmental analysis could be determined which is important to know that analyte quantity and time of poisoning of a person was exposed. For this purpose, 0.5 cm of pieces were cut along one or a few close strands and analyzed by solid sampling. This process could not be performed by wet-digestion method because 50 mg of sample is needed each time. Finally, the method was applied for the determination of copper and nickel concentrations in the hairs of different persons.     

Spectrophotometric estimation of cobalt(II) with nitrilotriacetic acid

A convenient and efficient method for the estimation of cobalt(II) ions in the presence of other metal ions is described. Interference of metal ions such as iron(II), iron(III), nickel(II), manganese(II), and copper(II) have been investigated. Only iron(III) ions seriously affect this determination. Copper(II) and nickel(II) ions do not interfere if present in a molar-ratio less than 1:2 in the cobalt(II) ion solution. Cobalt(II)-nickel(II) and cobalt(II)-copper(II) binary mixtures can be efficiently analyzed at selective wavelengths.     

Application of Total Reflection X-Ray Fluorescence Spectrometry in the Textile Industry

 In the present study, the determination of arsenic, lead, cadmium, chromium, cobalt, copper, nickel, mercury and zinc in various cloth samples produced in Kayseri-Turkey was performed after extraction with artificial sweat solution and decomposition with nitric acid. TXRF is shown to be suitable for the determination of 7 trace elements, down to the 0.001 (cobalt) to 0.004 (copper) mg/kg level in textile extract except for mercury and cadmium. The extractable part of the toxic metals by artificial sweat solution is relatively low. In a few extracts the concentration values of Pb and Ni have exceeded their critical values of 0.2 mg/kg for lead and 1.0 mg/kg for nickel given by ?ko-Tex and determined for babys cloths. In addition, it was observed that the element pattern of textile samples resembled ‘finger print type’, TXRF-spectra. This technique can also be used for the identification of textile sample in forensic investigation. Received April 16, 2001 Revision October 1, 2001.     

Field procedures to assess soils and waste disposals

The aim of this research was the development of rapid analytical test methods for arsenic, lead, cadmium, chromium(VI), copper, nickel, and zinc to classify waste materials into waste classes and assess contaminated soils for purification purposes. In order to estimate the danger potentials of contaminated soils, a rapid ecotoxicological method was developed (A. Götzl, H. Malissa, W. Riepe, FACT 3 (6) (1999) 329.). These rapid analytical and ecotoxicological tests offer an instrument to comprehensively assess soils and wastes. The developed rapid methods are suitable for the elution of different soils and wastes, the analysis of the eluates and also for waste waters with concentrations greater than 0.1 mg l⁻¹ arsenic, 0.5 mg l⁻¹ lead, 0.01 mg l⁻¹ cadmium, 0.1 mg l⁻¹ chromium(VI), 0.3 mg l⁻¹ copper, 0.5 mg l⁻¹ nickel and 0.1 mg l⁻¹ zinc in the eluate. Our developed rapid analytical test methods described below can be implemented on site, are of low cost and are not time-consuming (about 30 min). They also do not need to be carried out by highly qualified specialists only, they can also be easily applied by persons with some experience. The comparability of results obtained using the developed rapid test method and standardised methods was tested with various matrices.     

A New Ultramicrosensor for Nitric Oxide Based on Electropolymerized Film of Nickel Salen

Abstract

A new amperometric ultramicrosensor for the determination of nitric oxide (NO) is described. The ultramicrosensor, which is based on an electropolymerized film of ethylenebis(salicylideneiminate) nickel [Ni(salen)] and Nafion, shows a low detection limit, high selectivity and sensitivity to NO determination. The oxidation current (measured by a differential pulse amperometric method) is linear with NO concentration ranging from 1.0x10^?8 to 4.0x10^?6 mol/L with a calculated detection limit, at a signal to noise ratio of three, equal to 5.0x10^?9 mol/L. Some endogenous electroactive substances in biological tissues, such as dopamine, 5-HT and nitrite do not interfere with NO determination at the concentrations higher than those in biological systems. The ultramicrosensor could be employed for in vivo measurements of NO. The mechanism of the response of the ultramicrosensor to NO is also studied.     

Application of the slotted quartz tube in flow-injection flame atomic-absorption spectrometry

The slotted quartz has been applied to flow-injection flame atomic-absorption spectrometry (FI-FAAS) showing several important advantages. The tube life was improved by a factor of 5-6 compared to conventional continuous aspiration. Flow impact systems were found not to be necessary in the applications so that larger enhancement factors may be achieved without sacrifice in precision. For 1.0 mg/l. copper, 1.0 mg/l. lead, 0.1 mg/l. cadmium and 1.0 mg/l. gold sensitivity enhancement factors of 3.1, 5.5, 5.3 and 4.0 were obtained with precisions of 1.3%, 1.1%, 1.6% and 1.7% RSD (n = 11) respectively. Application of the slotted quartz tube FI-FAAS method to the determination of heavy metals in urine has shown improved tolerance to interfering matrices. Recoveries obtained by spiking undiluted urine samples with 0.1 mg/l. copper and lead, and 0.01 mg/l. cadmium were in the range 100-102%.