石墨炉原子吸收法直接测定海水中铅的方法探索

目的探索石墨炉原子吸收法直接测定海水中铅的检测方法。方法用硝酸铵稀释海水样品,用硝酸钯和磷酸二氢铵作为基体改进剂,用石墨炉原子吸收法测定了海水中的铅含量。结果通过加标回收的验证,检测结果准确可靠。结论适合用于海水中铅含量的测定。     

电感耦合等离子体质谱法(ICP-MS)测定镍钴锰三元氢氧化物中铅

研究了用电感耦合等离子体质谱法（ICP-MS）测定镍钴锰三元素氢氧化物中铅含量的测定方法。选择了仪器的最佳测量条件、元素测定的质量数,进行了基体元素的干扰等实验。方法测定结果准确、可靠,测定下限小于0.00005%,样品加标回收率在99.2%~101.0%。方法的建立为控制镍钴锰三元素氢氧化物中铅提供了检测依据。     

连续滴定法测定铅精矿中的铅、铜

建立了铅精矿中主量元素铅和次量元素铜的连续滴定分析方法。将铅滴定分析中经硫酸沉淀分离后的滤液,再经硫酸冒烟,用去离子水溶解后,通过滴定法对铅精矿中高含量铜进行分析。该方法铅精矿中铅的检出限为1.4 mg/g,铜的检出限为1.0 mg/g。对3个实际样品中铅、铜分别进行测定,测定结果的相对标准偏差均小于3.0%(n=7),铅的加标回收率为99.71%~100.19%,铜的加标回收率为99.33%~100.47%。该方法通过一次溶样,对铅精矿中的铅、铜连续进行滴定分析,方法快速、准确,适用于铅精矿中含量大于1.4%的铅和含量大于1.0%的铜的测定。     

The micro-volumetric determination of lead with thionalide and its application to the analysis of tin-base and lead-base alloys

The authors have elaborated an exact micro-volumetric method for the determination of lead with thionalide. The method has been successfully applied to the determination of lead in tin-base and lead-base alloys, following the isolation of lead as lead sulphate and its redissolution in ammonium acetate.     

Synthesis of a new solid-phase extractor and its application to preconcentration and determination of lead in water samples

A procedure for preconcentration and determination of lead in water is described. The method is based on the sorption of Pb(II) in a minicolumn packed with a functionalized sorbent and subsequent elution with acidic solution. The determination of lead content in the eluate was carried out using flame atomic absorption spectrometry. The sorbent was prepared by immobilization of the ligand 4-(5'-bromo-2'-thiazolylazo)orcinol on polystyrene-divinylbenzene through an azo spacer. Diazotization and coupling reactions were used for synthesis of the sorbent. Some variables affecting the preconcentration were optimized using a full factorial design. Under optimized conditions, the method presented a detection limit of 0.5 microg/L and enrichment factor of 36 for a sample volume of 25 mL. The accuracy of the method was tested by the determination of lead in a standard reference material (National Institute of Standards and Technology 1643d Fresh Water). The proposed procedure was applied to the determination of lead in samples of natural and drinking waters.     

二乙胺荒酸钠–四氯化碳萃取连续光源原子吸收法测定磷酸一二钙中的痕量铅、镉

建立连续光源原子吸收分光光度法同时测定磷酸一二钙(MDCP)中铅、镉的方法。MDCP经盐酸消解后,以氢氧化钠溶液调节p H为11,加入KCN作为掩蔽剂,用二乙氨荒酸钠–四氯化碳络合铅、镉离子,再经CCl_4进一步萃取浓缩,采用连续光源原子吸收分光光度法测定铅、镉的含量。该方法铅、镉的检出限为1,0.5 mg/kg;用于不同批次MDCP产品测定,铅、镉测定结果的相对标准偏差分别为3.58%,6.91%(n=11);铅、镉的加标回收率分别为88.9%~104.7%,91.0%~106.4%。该法可用于MDCP中痕量铅、镉的同时测定。     

Automated radioanalytical determination of lead and beryllium

The automated modification of the radioanalytical determination of lead and beryllium using AutoAnalyzer modules has been developed. The method for lead determination is based on a two-phase isotope exchange of lead between the sample solution labelled with²¹²Pb and the standard lead diethyldithiocarbamate solution in carbon tetrachloride. For the determination of beryllium a substoichiometric isotope dilution method using⁷Be as tracer and acetylacetone in chloroform as extractant was used. As little as 0.02 μg/ml of lead and 2 μg/ml of beryllium can be determined by the methods above. The flow diagrams of the automated procedures are presented.     

DBM-MSA光度法测定化妆品中铅

为建立一个新的测定化妆品中铅的分光光度法,在0．24mol／L的磷酸介质中,铅与DBM—MSA{3-[（2-磺酸基苯）偶氮]-6-[2,6-二溴-4-甲基苯）偶氮]-4,5-二羟基-2,7-萘二磺酸}反应形成1：2的蓝色配合物,在波长630nm处比色测定。结果表明,铅量在0—1μg／mL范围内符合比耳定律;样品测定的相对标准偏差为1．24％～4．59％,标准加入回收率为95．0％～107．0％,化妆品中共存物质不干扰测定,方法简便,选择性好,结果满意。     

Determination of 0.01-0.1% of samarium in 40-100 mg of lead chloride

A method is described for the determination of 5-25 mug of samarium in about 40 mg of lead chloride, based on the removal of the lead by electrolysis and determination of the samarium by extraction with PAN and measurement of the extinction of the complex at 552 nm.     

Simultaneous determination of lead and thallium by potentiometric stripping

A potentiometric stripping analysis procedure has been developed for the simultaneous determination of lead and thallium in chloroacetate-chloride medium. This procedure allows the determination of lead or thallium concentrations as low as 10 ng ml . The method is precise, and applicable to the determination of lead and thallium in sea-water.     

Extractive fluorimetric determination of ultratraces of lead with cryptand 2.2.2 and eosin

A new speetrofluorimetric method for determination of ultratraces of lead is based on solvent extraction into chloroform of the ion-pair formed between the positively-charged cryptate of lead with cryptand 2.2.2 and the eosinate anion. The detection limit for lead is 1 ng ml , and the linear working range is from the detection limit to 250 ng ml . The relative standard deviation is 3.7% at the 100 ng ml level. The method is highly selective for the extraction and determination of lead in the presence of other cations, and has been tested for direct determination of lead contamination in soft drinks. Aggregation of the extracted ion-pair in the organic phase has been demonstrated in fundamental extraction studies.     

电感耦合等离子体原子发射光谱法测定废蓄电池硫酸铅及其脱硫物中的硫

建立废蓄电池硫酸铅及其脱硫物中硫含量的测定方法。样品采用硝酸、盐酸消解样品,电感耦合等离子体原子发射光谱法测定废蓄电池硫酸铅及其脱硫物中硫的含量。在选定的仪器工作条件下,大量Pb,Al,Fe等基体元素的存在不影响硫的测定。硫的质量浓度在0.00~80.00 mg/L范围内与其光谱强度具有良好的线性关系,线性相关系数为0.999 9,检出限为0.14 mg/L。测定结果的相对标准偏差为2.18%~5.22%(n=11),样品加标回收率在95.0%~104.2%之间。该方法的测定结果与重量法测定结果一致。该方法简单易行,测定结果准确可靠,重复性好,可用于废蓄电池硫酸铅及其脱硫物中硫的测定。     

Simultaneous determination of tin and lead by a.c. anodic stripping voltammetry at a hanging mercury drop electrode sensitized by cetyltrimethylammoniu

The influence of cetyltrimethylammonium bromide (CTAB) on the simultaneous determination of tin(IV) and lead(II) by anodic stripping voltammetry at a hanging mercury drop electrode (HMDE) in a 0.1 M hydrochloric acid—0.1 M oxalic acid medium was studied using d.c. and a.c. stripping. In the presence of CTAB, tin and lead show voltammetric peaks separated by 100 mV, the sensitivity depending on the concentration of CTAB. The best conditions for the simultaneous determination of both elements (2 × 10^-3 M) were found. A method is proposed for the determination of tin in the presence of lead and three procedures are given for the determination of lead in the presence of tin.     

微波消解–石墨炉原子吸收法测定药食两用中药材中的铅

建立测定药食两用中药材中铅含量的微波消解–石墨炉原子吸收光谱分析方法。样品经微波消解后,以2%磷酸二氢铵为基体改进剂,用石墨炉原子吸收法测定药食两用中药材中的铅含量。在2~40μg/L范围内,铅的质量浓度与吸光度呈良好的线性关系,线性相关系数r大于0.999,检出限为5μg/kg。加标回收率为94.0%~105.5%,测定结果的相对标准偏差小于5.0%(n=6)。该方法操作简便快速,准确度较高,基体干扰小,适合药食两用中药材中铅的检测。     

Lead determination in wine by potentiometric stripping analysis

Summary Computerized potentiometric stripping analysis (PSA) was used for lead determination in wine samples. In this method sample preparation before determination is limited to dilution with an appropriate supporting electrolyte (0.5 mol/l HCl and 40 mg/l Hg²⁺). Due to the very high sensitivity, the time needed for one determination can be reduced to 2 min. The method was tested by lead determination in different wines, different concentration ranges and in one European interlaboratory comparison organized by BCR. Using PSA it is possible to simultaneously determine cadmium, lead and copper in wine. For other elements such as Bi, Tl, Hg, Sn, As, Zn the determination procedures are under development. The PSA equipment is available on the market, small in size, relatively cheap and it does not require any special installation such as gas or cooling water.     

Cloud point extraction of lead in saliva via use of nonionic PONPE 7.5 without added chelating agents

A new micelle-mediated phase separation of metal ions to preconcentrate trace levels of lead as a prior step to its determination by flame atomic spectroscopy has been developed. The methodology is based on the cloud point extraction of lead with PONPE 7.5 in the absence of chelating agent. The chemical variables affecting the sensitivity of the extractive-spectrometric procedure were evaluated in detail, optimised and successfully applied to the determination of lead in saliva samples. Under the optimal conditions, a %E higher than 99.9 was achieved. The proposed method showed linear calibration within the range: 0.6-4 mug ml(-1) Pb(II). The sensitivity was 0.053 mug ml(-1). The method has been applied to the determination of lead in human saliva. The nature of the extracting species as well as the location of lead in the micelle were studied. The analytical performance of the proposed method clearly satisfies the typical requirements for control processes.     

Simultaneous Determination of Arsenic and Lead in Vegetable Oil by Atomic Fluorescence Spectrometry after Vortex-Assisted Extraction

Hydride generation atomic fluorescence spectrometry (HG-AFS) is used for the determination of hydride-forming elements due to its high sensitivity, simplicity, and low cost. A new HG-AFS method for the simultaneous determination of arsenic and lead in vegetable oil is reported. Vortex-assisted extraction with dilute nitric acid was used to isolate arsenic and lead from vegetable oil. The conditions influencing the fluorescence signal, including the carrier fluid, oxidizing agent, and reducing agent, were optimized. The interferences of coexisting ions were also evaluated. Under the optimized conditions, the limits of detection were 0.6 and 0.4?µg?kg^?1 for arsenic and lead. The recoveries were from 84.4 to 105% for both metals in vegetable oil. The optimized method was used for the determination of arsenic and lead in commercial vegetable oil. The analytical results by this approach were in good agreement with values obtained by inductively coupled plasma mass spectrometry with microwave digestion.     

Flow-injection analysis of traces of lead and cadmium by solvent extraction with dithizone

An automated solvent extraction method for determination of lead and cadmium down to the 50 ng/ml level has been developed. Optimum conditions for selective and sensitive determination were designed and verified by using the flow-injection scanning method.     

PAN-6S作络合指示剂连续滴定测定汞和铅的研究

试验研究了pH3.0和pH5.4的介质中,以1 (2 吡啶偶氮) 2 萘酚 6 磺酸(PAN 6S)作为指示剂,以EDTA为滴定剂连续滴定汞和铅,其终点颜色变化敏锐,准确度高。