Use of the vanadium(V)-xylenol orange mixture as an improved reagent for the spectrophotometric determination of traces of hydrogen peroxide

The reaction in V(V)-xylenol orange (XO)-H₂O₂ system was studied by spectrometry. On the addition of hydrogen peroxide to the mixture of vanadium(V) and XO (V-XO reagent), the absorption peak of V(V)-XO complex (λ_max = 582 nm) decreased significantly. The decrease in the absorbance (denoted as ΔA) was proportional to the concentration of hydrogen peroxide. The constant values of ΔA were obtained under the condition of [XO]/[V(V)] = 0.5 ~ 1.2 and in the pH 3.5 ~ 4.5 region. Based on these results, the conditions for the use of the V-XO reagent in the colorimetric determination of hydrogen peroxide were examined in detail. The V-XO reagent was found to be useful for the trace analysis of hydrogen peroxide with high sensitivity, and the data were little affected by the presence of some inorganic and organic substances. The lower limit of the determination is about 1 × 10^?6M.     

The kinetics of complex formation between Ti(IV) and hydrogen peroxide

The kinetics of the formation of the titanium‐peroxide [TiO²⁺₂] complex from the reaction of Ti(IV)OSO₄ with hydrogen peroxide and the hydrolysis of hydroxymethyl hydroperoxide (HMHP) were examined to determine whether Ti(IV)OSO₄ could be used to distinguish between hydrogen peroxide and HMHP in mixed solutions. Stopped‐flow analysis coupled to UV‐vis spectroscopy was used to examine the reaction kinetics at various temperatures. The molar absorptivity (ε) of the [TiO²⁺₂] complex was found to be 679.5 ± 20.8 L mol^?1 cm^?1 at 405 nm. The reaction between hydrogen peroxide and Ti(IV)OSO₄ was first order with respect to both Ti(IV)OSO₄ and H₂O₂ with a rate constant of 5.70 ± 0.18 × 10⁴ M^?1 s^?1 at 25°C, and an activation energy, E_a = 40.5 ± 1.9 kJ mol^?1. The rate constant for the hydrolysis of HMHP was 4.3 × 10^?3 s^?1 at pH 8.5. Since the rate of complex formation between Ti(IV)OSO₄ and hydrogen peroxide is much faster than the rate of hydrolysis of HMHP, the Ti(IV)OSO₄ reaction coupled to time‐dependent UV‐vis spectroscopic measurements can be used to distinguish between hydrogen peroxide and HMHP in solution. © 2007 Wiley Periodicals, Inc. Int J Chem Kinet 39: 457–461, 2007     

Solubility behavior of titanium(IV) oxide in alkaline media at elevated temperatures

A platinum-lined, flowing autoclave facility was used to investigate the solubility behavior of titanium dioxide (TiO₂) in aqueous sodium phosphate, sodium hydroxide and ammonium hydroxide solutions between 17 and 288°. Baseline Ti(IV) solubilities were found to be on the order of one nanomolal, which were enhanced by the formation of anionic hydroxo- and phosphato-complexes. The measured solubility behavior was examined via a titanium(IV) ion hydrolysis/complexing reaction equilibria were obtained from a least squares analysis of the data. The existence of three new Ti(IV) ion complexes is reported for the first time: Ti(OH)₄(HPO₄)^2–, Ti(OH)₅(H₂PO₄)^2– and Ti(OH)₅(HPO₄)^3–. The triply-charged anionic complex was the dominant Ti(IV) species in concentrated, alkaline phosphate solutions at elevated temperatures. This complex is expected to exhibit C.N.=4 (i.e., Ti(OH)₂OPO ₄ ^3– ). A summary of thermochemical properties for species in the systems TiO₂-H₂O and TiO₂-P₂O₅-H₂O is also provided.     

A spectrophotometric study of the formation of the peroxotitanium(IV) complex and its application to the determination of beryllium

The formation of peroxotitanium(IV) complexes has been studied spectrophotometrically in (a)Ti(IV)-H₂O₂,(b)Ti(IV)-H₂O₂-HF and (c)Ti(IV)-H₂O₂-HF-Be(II) systems containing 2M hydrochloric acid. In system (a),only a 1:1 peroxotitanium(IV) complex is evident. In system (b), the competitive formation of the peroxotitanium(IV) complex and fluorotitanium(IV) complexes is discussed. In system (c), the formation of fluoroberyllium(II) complexes causes an increase in concentration of the peroxotitanium(IV) complex which is proportional to the concentration of added beryllium(II). The determination of beryllium in a Cu-Be alloy was successful with a Ti(IV)-H₂O₂-HF reagent.     

Oxidation of methyl phenyl sulfide with hydrogen peroxide catalyzed by Ti(IV)-substituted heteropolytungstate

Alkylammonium salts of Ti(IV)-substituted heteropolytungstate, PW₁₁TiO ₁₀ ⁵⁻ , catalyze the oxidation of methyl phenyl sulfide with hydrogen peroxide. The yield of the corresponding sulfoxide and sulfone is practically quantitative. A³¹P NMR study confirms the formation and reactivity of the PW₁₁O₃₉TiO ₂ ⁵⁻ peroxo complex in organic media.     

Spectrophotometric determination of titanium (IV) with chlorpromazine hydrochloride

Spectrophotometric Determination of Titanium(IV) with Chlorpromazine HydrochlorideThe extraction of titanium(IV)-thiocyanate complex from hydrochloric acid with chlorpromazine (CPA) dissolved in chloroform has been studied. The composition of the extracted species was found to be (CPAH⁺)₂[Ti(CNS)₆²⁻]. This complex, dissolved in chloroform, has maximum absorbance at 417 nm and a molar absorptivity of 2.6 × 10⁴ mol⁻¹ · cm⁻¹ · liter. Titanium(IV) was determined spectrophotometrically in the organic phase. Beer's law is obeyed in the titanium concentration range 0.2-2.2 μg/ml.     

Analytical applications of mixed-ligand complexes: II. Determination of hydrogen peroxide in the presence of perioxide derivatives

The mixed ligand complex TiXOH₂O₂ was found suitable for the determination of small amounts of hydrogen peroxide in the presence of peroxy acids of sulfur. The pH optimum for the determination depends on the concentrations of the reagents [titanium (IV) and xylenol orange]: for 2 × 10^?4M titanium (IV) and XO the optimum pH is 1.25. ?⁵²⁰ = 13,200 M^?1 cm^?1. The method is suitable for determination of 4–40 μM H₂O₂. Mention is made of the possible causes of the contradictions to be found in the literature concerning the ternary complex.     

Colorimetric determination of palladium (II) by means of promazine hydrochloride

In acetate buffer medium palladium(II) ions form with promazine hydrochloride (PM) two complexes: an orange one of a formula [Pd(C₁₇H₂₀N₂S)]²⁺ (λ_max = 460 nm, ε = 4.5 × 10³, at 20 °C and pH = 2) and a violet one of a formula [Pd(C₁₇H₂₀N₂S)₂]²⁺ (λ_max = 540 nm, ε = 8.8 × 10³ at 20 °C and pH = 2).The values for instability constants determined by Bjerrum's method amount to pK₁ = 3.95; pK₂ = 3.07; pβ₁ = 3.95; pβ₂ = 7.02, respectively.A colorimetric method of the determination of palladium(II) has been elaborated. The method consists in a measurement of the absorbance of the violet complex of palladium(II) with promazine hydrochloride at λ = 540 nm. The method permits the determination of 2–17 μg Pd/ml with an error of ±2%. The time of the determination is 20 min. Iron(III), Ce(IV), Pt(IV), V(V), Cr(VI), and HNO₃ interfere with the determination.     

Chromatographic behaviour of metal ions on tin(IV) and titanium(IV) antimonate papers

Summary The chromatographic behaviour of 49 metal ions has been studied on papers impregnated with Sn(IV) and Ti(IV) antimonates in aqueous HNO₃ and mixed solvent systems containing dimethyl sulphoxide. Numerous separations have been achieved and the Alberti equation, for Sn(IV) and Ti(IV) antimonate papers, in the modified form: –nloga K⁺=R_M + constant (a K⁺=activity of K⁺), has been verified. The effect of the concentration of impregnating reagents on these papers has been determined and compared with other papers. The effect of pH on R_f, R_i, log R_f and R_M values of metal ions has also been examined in aqueous systems.     

Electrochemical amination. Ti(IV)/Ti(III) mediator system in aqueous solutions of sulfuric acid

As a result of polarographic and spectrophotometric studies, and mathematical modeling, the dependence of electrochemical properties of the Ti(IV)/Ti(III) pair on the composition of the Ti(IV) complexes is established in sulfuric acid solutions. It is found that Ti(IV) in 1–17 M H₂SO₄ at the metal ion concentrations used in the process of amination of aromatic compounds can exist in the form of twelve basic complex forms, of which seven, including the binuclear and two tetranuclear ones, are observed for the first time. Ten forms are electrochemically active. An increase in the overall amount of reversibly reducing cationic mononuclear hydrosulfate complexes of Ti(IV) among these at a growing H₂SO₄ concentration results in an increase in the redox potential of the Ti(IV)/Ti(III) mediator system and therefore in an increase in the yield of the electrochemical amination products.     

Spectrophotometric extractive determination of Ti in mineral samples and aluminium alloys as a mixed-ligand Ti(IV)-salicylhydroxamic acid-thiocyanate complex

A sensitive method for the determination of titanium, based on the formation of a mixed-ligand Ti (IV)-salicylhydroxamic acid-thiocyanate complex and extraction of this into a liquid ion-exchanger phase has been developed. The extract has maximum absorbance at 400–460 nm and the apparent molar absorptivity is 1.8 × 10⁴l · mole^–1 · cm^–1 at 420 nm. The system obeys Beer's law at 420 nm in the range 0.16–3.20 mg/1 Ti, the detection limit being 0.1 mg/1. The method is found suitable for determination of titanium in aluminium alloys and silicate rocks.     

Application of Alizarine Derivatives as Chromogenic Reagents for the Spectrophotometric Determination of Some Sulfa Drugs

A spectrophotometric procedure for the determination of six pharmaceutical sulfonamides containing a primary aromatic amino group using alizarine (I), alizarine blue (II), alizarine red (III), and quinalizarine (IV), that offers advantages of simplicity, rapidity, sensitivity, precision, and stability, has been developed. The proposed method is based on the formation of colored products with the chromogenic reagents (I-IV). A linear correlation was found between absorbance at λ_max and the concentration. For more accurate results, Ringbom optimum concentration ranges are evaluated. The molar absorptivities (ε), absorptivities (a), and Sandell sensitivities for all sulfonamides derivatives with the chromogenic reagents tested were calculated. The procedures developed are applied for bulk sulfa drugs and some of their dosage forms.     

Spectrophotometric determination of molybdenum by extraction of its thiosulphate complex

A simple and rapid spectrophotometric determination of molybdenum is described. The molybdenum thiosulphate complex is extracted into isoamyl alcohol from 1·0–1·5M hydrochloric acid containing 36–40 mg of Na₂S₂O₃·5H₂O per ml. The absorbance at λ_max = 475 nm obeys Beer's law over the range 0–32 μg of Mo per ml of solvent phase. Up to 5 mg/ml of Ti(IV), V(V), Cr(VI), Fe(III), Co(II), Ni(II), U(VI), W(VI), Sb(III), 1 mg/ml of Cu(II), Sn(II), Bi(V) and 10 μg/ml of Pt(IV) and Pd(II) do not interfere. Large amounts of complexing agents interfere. The method has been applied to analysis of synthetic and industrial samples.     

Radiation chemistry of xylenol orange in aqueous solutions at different acidities

The radiolytic decolourization and peroxide formation have been studied in aqueous solutions of xylenol orange (XO) at different acidities. The G(-XO) increases from 0.78 at pH 11, to 3.70 at pH 3. The peroxide yield also increases from 1.19 at pH 11, to 3.34 in 0.025 mol dm^-3 H₂SO₄. In alkaline solutions only the OH^. decolourizes XO whereas in acidic solutions both the H and OH^. decolourize XO though G(-XO) due to H-atoms is less. The ionization of the phenolic group in XO influences the e^-_aq reaction with it. In alkaline solution, the oxidized and reduced XO formed by OH^. and e^-_aq reactions, respectively, react together regenerating original XO. Near 0.025 mol dm^-3 H₂SO₄, there is an abstraction of H-atom from XO by HO₂ whereas at other acidities, H₂O₂ is formed by disproportionation of peroxides. Reaction schemes have been given to explain the various radiolytic yields.     

Formation of TiO2 Sols,Gels and Nanopowders from Hydrolysis of Ti(OiPr)4 in AOT Reverse Micelles

Titania sols, gels and nanopowders have been produced by the controlled hydrolysis of tetraisopropyltitanate (TPT) in sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reverse micelles. Particle formation and aggregation have been investigated by photon correlation spectroscopy, the crystal phases by FT-Raman spectroscopy, and the crystallite dimensions of the precipitates by transmission electron microscopy. Nanoparticles could be produced at relatively high Ti(IV) concentrations (up to 0.05 mol dm^–3). These nanoparticles aggregated into sols, with colloid sizes of 20–300 nm, eventually forming gelatinous precipitates. The kinetics of particle formation and aggregation were controlled by varying the primary process parameters [TPT], [H₂O]/[AOT] (w₀), and [H₂O]/[Ti(IV)] (R), yielding a range of products including stable, transparent sols, precipitates and monolithic gels. The aggregation kinetics and physical properties of the sols depended strongly on w₀. Different titania phases were produced, depending on w₀; w₀ 6 yielded amorphous particles, while w₀ 10 produced anatase. The dimensions of the crystallites were comparable to those of the parent reverse micelles. A model was developed to interpret the effect of the primary process parameters on colloidal stability: (1) nucleation to form primary crystallites occurs by rapid hydrolysis and condensation reactions within the reverse micelle and (2) subsequent colloidal growth by aggregation occurs by reverse micellar exchange, where the rate of growth is governed by electrostatic and steric stability factors which increase as [AOT]/[TPT] (S) and residual [H₂O]/[AOT] (w_r) increase.     

Spectrometric Determination of Ti(IV) With an Azopyrazolonic Derivative

Abstract

Spectrometric studies on the complexation of Ti(IV) with a new organic reagent obtained by coupling 3-methyl-1-phenyl-5-pyrazolone with diazotized 3-amino-4-hydroxy-benzene-sulphonic acid were carried out.

A 1:2 Ti(IV):reagent complex, which is soluble in water, is formed at pH 5–6.2. The maximum absorbance of the complex lies at λ =520nm, where the absorbance of the reagent is very low. The molar absorptivity at this wavelength is 5 × 10³ L mol^?1 cm^?1; the value of log K is 8.0 ± 0.2. at 20 ± 1°C and pH=5.6.     

Pamoic acid in forming metallo-organic framework: Synthesis, characterization and first crystal structure of a dimeric Ti(IV) complex

Two novel dinuclear Ti(IV) complexes of the ligand, 4,4′-methylene-bis (3-hydroxy-2-naphthalene carboxylic acid) (H₄L) or pamoic acid having compositions, [(HL)₂Ti₂(μ-O)(DMF)₂]·(DMF)₆ (1) and [(L)₂Ti₂(μ-O)(DMF)₂]·(DMF)₄(4,4′-Bipy-2H)(H₂O), (2) have been synthesized and characterized by analytical and spectral methods and the structure has been established by single crystal XRD. Unlike the reported polymeric structures observed in case of H₄L or pamoic acid, the anti-conformation of H₄L changes to syn - orientation to avoid poly-metallic complex formation, as noticed in 1 and 2. The dimeric Ti(IV) units stack in the lattice to form helical columns and the space between the adjacent columns is being filled by the solvent molecules in 1 and solvent plus the protonated 4,4′-bipy in the lattice of 2 and thus the neighbor columns are connected through weak interactions.     

Radical trifluoromethylation of Ti ate enolate: possible intervention of transformation of Ti(IV) to Ti(III) for radical termination

The radical trifluoromethylation of ketone Ti ate enolates gave α-CF₃ ketones in good yields. The use of excess amount of LDA and Ti(OⁱPr)₄ in the preparation of Ti ate enolates is the key to the efficient radical trifluoromethylation. Theoretical studies on the spin density of the Ti(IV) ate ketyl radical intermediate suggest the involvement of transformation from Ti(IV) ate ketyl radical intermediates to Ti(III) species in a radical termination step.     

Studies on Simultaneous Fluorescence-Spectrophotometric Determination of Ultratrace Niobium(V), Tantalum(V), and Zirconium(IV) Using Partial Least-Squares Algorithm

In the presence of cetyltrimethylammonium bromide, a cationic surfactant, highly sensitive molecular fluorescence reactions occur between Nb(V), Ta(V), and Zr(IV) ions and morin (3, 5, 7, 2′, 4′-pentahydroxyflavone) in acidic medium to form stable ternary micellar complexes. Their λ_ex(max)/λ_em(max)values are 421.0/492.2, 416.2/489.6, and 424.2/507.8 nm, respectively, and their λ_em(max)values are 490.5, 488.6, and 507.2 nm, respectively, at the same fixed λ_exof 420.5 nm, indicating their seriously overlapping fluorescence excitation spectra and fluorescence emission spectra. The linear ranges of their regression calibration curves are 0 to 0.20, 0 to 0.50, and 0 to 0.20 mg/liter, respectively, with 0.5 ng/ml for all of sensitivities. The simultaneous molecular fluorescence-spectrophotometric determination of ultratrace or trace Nb(V), Ta(V), and Zr(IV) without separation was made using a partial least-squares (PLS) algorithm and other algorithms. The optimum PLS computation conditions are wavelength point number of 25 and corresponding wavelength range from 450 to 550 nm oriented from λ_em500 nm to two sides at combined intervals of 2.5 and 5.0 nm at a fixed λ_exof 420.5 nm with an optimum calibration sample number of 14 and respective optimum abstracted factor numbers of 6, 4, and 3. With respect to both accuracy and precision of the obtained results, the PLS algorithm is superior to the ordinary least-squares algorithm.     

Analytical applications of mixed-ligand complexes: III. Vanadium(V)-xylenol orange reagent mixture for the spectrophotometric determination of traces of hydrogen peroxide

Vanadium(V) forms 2:1, 1:1, and 1:2 binary complexes with xylenol orange (XO). In slightly alkaline solution the formation of the complexes is almost instantaneous, whereas it takes a day for the equilibria to be reached at pH 4. On the action of hydrogen peroxide, both the 2:1 and the 1:1 complexes are transformed into mixed-ligand complexes, with 2:1:2 and 1:1:1 compositions, respectively. No intramolecular redox reaction takes place between XO and hydrogen peroxide. Peroxo complex formation can be used for estimation of hydrogen peroxide if the decrease in absorbance of the 576-nm band of the binary complexes is measured. The molar absorptivity decrease depends on the ratio $\text{[V(V)]}\text{[XO]}$ and the pH.