A simple diffuse reflectance Fourier transform infrared spectroscopic determination of sulfur dioxide in ambient air using potassium tetrachloromercurate as the absorbing reagent

This paper presents development of a simple, rapid, and precise analytical method for determination of sulfur dioxide in ambient air by a gas to solid-phase conversion method. Sulfur dioxide is determined in the form of sulfite (SO3(2-)) because the absorbing reagent, potassium tetrachloromercurate (TCM), used in this method absorbs sulfur dioxide from the atmosphere in the form of sulfite. Determination of submicrogram levels of sulfur dioxide was based on the selection of a quantitative analytical peak at 495 cm(-1) among the 3 observed vibrational peaks for the dichlorosulfitomercurate complex formed after reaction of sulfur dioxide with TCM and measurement of absorbance using diffuse reflectance Fourier transform infrared spectroscopy. The limits of detection and quantification of the method were found to be 0.09 and 0.4 microg/g SO3(2-), respectively. The precision in terms of standard deviation and relative standard deviation (RSD) at a level of 2 microg SO3(2-)/10.1 g KBr for n = 10 was found to be 0.036 microg SO3(2-) and 1.8%, respectively. The RSD (n = 10) for determination of sulfur dioxide in ambient air was observed to be in the range of 2.7-4.2%. The method proposed is time saving and eliminates the slow and cumbersome steps of pH maintenance of the reaction mixture and color formation of the U.S. Environmental Protection Agency recommended West and Gaeke spectrophotometric method and other methods for quantitative determination of sulfur dioxide.     

Sulfur speciation by capillary zone electrophoresis: conditions for sulfite stabilization and determination in the presence of sulfate, thiosulfate and peroxodisulfate

Capillary zone electrophoresis (CZE) was used for the separation of the sulfur species SO3(2-), SO4(2-), S2O(3-) and S2O8(2-). Using an electrolyte system with 9.5 mmol L(-1) potassium chromate as UV-absorbing probe and 1 mmol L(-1) diethylenetriamine (DETA) as electroosmotic flow modifier, various possibilities for the stabilization of sulfite and electrophoretic separation of the sulfur anions were investigated. By adding 5% propanol as a stabilizer to both the working electrolyte and the sample solution, a good stabilization for sulfite and a separation of the sulfur anions in a short analysis time (4 min) was achieved. The advantages by using propanol instead of other stabilizers often used in analytical techniques are discussed. The electrophoretic separation of the sulfur anions was optimized with respect to the pH of the working electrolyte and concentration of the electroosmotic flow modifier (DETA). The detection limits achieved for SO3(2-), SO4(2-), S2O3(2-) and S2O8(2-) were 0.35, 0.25, 0.78 and 0.80 mg L(-1), respectively.     

On-line collection/concentration and detection of sulfur dioxide in air by flow-injection spectrophotometry coupled with a chromatomembrane cell.

A simple and rapid procedure for SO2 determination in air was developed by using a flow injection analysis (FIA) system coupled with a 3-hole chromatomembrane cell (CMC). The CMC was applied for the on-line collection/concentration of SO2 from air into a solution of 2 g l(-1) triethanolamine (TEA) solution as an absorbing solution: SO2 was converted to SO3(2-) in the alkaline absorbing solution. The solution containing absorbed SO2 was introduced into the carrier stream of the FIA system. The amount of SO3(2-) in the absorbing solution was measured by spectrophotometry with a mixed reagent of pararosaniline and formaldehyde, and was converted to the concentration of SO2 in the air sample. A calibration graph prepared by using standard sodium sulfite aqueous solutions was adopted for the determination of SO3(2-) in the absorbing solution. The SO2 concentration in indoor air examined was found to be 22.7 +/- 0.2 ppbv using 20 ml of air sample with the air flow rate of 5 ml min(-1), where the relative standard deviation was 1.7%. The detection limit for aqueous solutions and air samples were 6.9 x 10(-8) M and 0.48 ppbv, respectively. The measuring time for one sample was about 10 min when a 20 ml air sample was used. The interferences from common anionic species, formaldehyde and acetaldehyde, were also examined.     

Renewable-surface sol-gel derived carbon ceramic electrode fabricated by [Ru(bpy)(tpy)Cl]PF6 and its application as an amperometric sensor for sulfide and sulfur oxoanions

A highly sensitive and fast responding sensor for the determination of thiosulfate, sulfite, sulfide and dithionite is described. It consists of a chemically modified carbon ceramic composite electrode (CCE) containing [Ru(bpy)(tpy)Cl]PF6 complex that was constructed by the sol-gel technique. A reversible redox couple of Ru(II)/Ru(III) was observed as a solute in acetonitrile solution and as a component of carbon based conducting composite electrode. Electrochemical behavior and stability of modified CCE were investigated by cyclic voltametry, the apparent electron transfer rate constant (kappa(S)) and transfer coefficient (a) were determined by cyclic voltametry which were about 28 s(-1) and 0.43 respectively. Electrocatalytic oxidation of S(2-), SO3(2-), S2O4(2-) and S2O3(2-) were effective at the modified electrode at significantly reduced overpotentials and in the pH range 1-11. Optimum pH values for amperometric detection of thiosulfate, dithionite, sulfide and sulfite are 7, 9, 2 and 2. Under the optimized conditions the calibration curves are linear in the concentration ranges 1-500, 3-80, 2-90 and 1-100 microM for S2O3(2-), SO3(2-), S2- and S2O4(2-) determination. The detection limit (signal to noise is 3) and sensitivity are 0.5 and 12, 2.8 and 6, 1.6 and 8, and 0.65 microM and 80 nA microM(-1) for thiosulfate, sulfite, sulfide and dithionite detection. The modified carbon ceramic electrode doped with Ru-complex shows good reproducibility, a short response time (t < 2 s), remarkable long term stability (> 6 month) and especially good surface renewability by simple mechanical polishing (RSD for eight successive polishing is 2%). The advantages of this sulfur compound amperometric detector based on ruthenium doped CCE are high sensitivity, inherent stability at a broader pH range, excellent catalytic activity, less expense and simplicity of preparation in comparison with recently published papers. This sensor can be used as a chromatographic detector for analysis of sulfur derivatives.     

Highly efficient photoinitiation in the cerium(III)-catalyzed aqueous autoxidation of sulfur(IV). An example of comprehensive evaluation of photoinduced chain reactions

The photoinitiated and cerium(III)-catalyzed aqueous reaction between sulfite ion and oxygen has been studied in a diode-array spectrophotometer using the same light beam for excitation and detection. Cerium(III) is identified as the photoactive absorbing species, and the production of cerium(IV) initiates a radical chain reaction. To interpret all the experimental findings, a simple scheme is proposed, in which the additional chain carriers are sulfite ion radical (SO3(-.)), sulfate ion radical (SO4(-.), and peroxomonosulfate ion radical (SO5(-.). The overall rate of oxidation is proportional to the square root of the light intensity per unit volume, which is readily interpreted by the second-order termination reaction of the proposed scheme. It is also shown that the reaction proceeds for an extended period of time in the dark following illumination, and a quantitative analysis is presented for this phase as well. The postulated model predicts that cerium(III) should have a cocatalytic or synergistic effect on the autoxidation of sulfite ion in the presence of other catalysts. This prediction was confirmed in the iron(III)-sulfite ion-oxygen system. The experimental method and the mathematical treatment used might be applicable to a wide range of photoinduced chain reactions.     

离子色谱法测定烟气脱硫海水中的亚硫酸根离子

建立了燃煤电厂烟气脱硫海水中亚硫酸根(SO2~3)的离子色谱-脉冲安培检测方法。色谱柱为IonPac AS14A阴离子交换柱,流动相为14 mmol/L NaOH-12 mmol/L Na2CO3溶液(pH 11.7),流速1.2 mL/min,脉冲安培法检测。因SO2~3易被氧化,故在采样时加入甲醛作为保护剂,使之稳定存在。在测定海水样品前,用NaOH溶液(pH 12.0)沉淀海水中的Mg2+,以避免其在pH较高的流动相中生成沉淀堵塞色谱柱。采用该方法检测SO2~3的线性范围为0～100 mg/L,平均回收率为116.8%,检出限为0.05 mg/L;对7.5,25.0和75.0 mg/L的海水基底加标溶液分别进行9次平行测定,其相对标准偏差(RSD)分别为2.1%,3.1%和4.0%。该方法具有快速、灵敏、选择性好等特点,用于烟气脱硫的海水中SO2~3的检测,可得到令人满意的结果。     

Chemiluminescent investigation of tris(2,2'-bipyridyl)ruthenium(II) immobilized on a cationic ion-exchange resin and its application to analysis

Tris-(2, 2'-bipyridyl)ruthenium(II) complex, Ru(bpy)(3)(2+), was immobilized on the Dowex-50 W cationic ion-exchange resin. The chemiluminescent characteristics of Ru(bpy)(3)(2+) in solution and in resin form were compared by using batch and flow injection methods. A strong chemiluminescence was observed during the reaction of Ru(bpy)(3)(2+) both in solution and in resin with KMnO(4) or Ce(SO(4))(2) under acidic or basic conditions. The Ru(bpy)(3)(2+) immobilized resin is stable, which can be used at least for 6 months when it reacts with the dilute KMnO(4) solution. Based on this property, Ru(bpy)(3)(2+) immobilized in the resin phase was developed as a flow-through chemiluminescent sensor that could be used to determine oxalate, sulfite and ethanol chemically or electronically with Ru(bpy)(3)(3+) generation on the surface of resin. The limits of detection were 1 x 10(-6) M for oxalate, 0.5% (v/v) for ethanol and 1 x 10(-7) M for sulfite. The method has been successfully applied to determine sulfite in sugar.     

高效液相色谱法分析牛和猪肌肉组织中残留的安乃近药物的三种代谢物

建立了牛和猪肌肉组织中残留的安乃近药物的3种代谢物 4-甲酰氨基安替比林（FAA）、4-氨基安替比林（AA）和 4-甲基氨基安替比林（MAA）的高效液相色谱测定法。肌肉组织样品均质后采用硫酸钠-亚硫酸钠溶液提取,过滤后经C18固相萃取柱净化,采用Inertsil ODS-3色谱柱分离,甲醇和水梯度洗脱,于265 nm波长下检测,外标法定量FAA,内标法定量AA和MAA（以 4-异丙基氨基安替比林作为内标物）。FAA的检出限为12.5 μg/L,AA的检出限为15.0 μg/L,MAA的检出限为20.0 μg/L;3种代谢物的测定低限均为50 μg/L;在添加水平为50～400 μg/kg范围内,FAA的回收率为81.3%~92.5%,AA的回收率为82.0%~96.0%,MAA的回收率为80.4%~90.6%,相对标准偏差均在7%以内。     

Identification of lead in metal food can seams using 57Co RXRFS

Radioisotope-induced X-ray fluorescence spectrometry procedures developedfor screening solder for Pb are described. By using 57 Co as an excitationsource, food cans with Pb-soldered seams were easily distinguished from othertypes of metal cans. Limits of detection (3) for Pb in metal food can seamswere 0.1 and 0.3 mg Pb/cm 2 for count times of 1 hour and 3 minutes, respectively.Pb/Sn ratios were determined for commercial solders containing 0.6% to 84%Pb. Pb content was quantified as low as 0.07%, and Bi and Sb content couldbe determined for some commercial solders.     

Determination of sulfite in water samples by flow injection analysis with fluorescence detection

<正>A fast,sensitive,and reliable method for the determination of sulfite(SO_3~(2-)) in fresh water and seawater samples was developed.The proposed method was based on the reaction of o-phthalaldehyde(OPA)-sulfite-NH_3 in alkaline solution,with flow injection analysis and fluorescence detection.The experimental parameters were investigated in pure water and seawater matrixes. The detection limits(S/N = 3) were 0.006μmol/L in pure water and 0.018μmol/L in seawater for SO_3~(2-).The method was successfully applied to analyze SO_3~(2-) in the samples of rain water and flue gas desulfurization seawater.     

Capillary electrophoretic determination of thiosulfate and its oxidation products

Capillary electrophoresis (CE) was developed for the rapid and simple determination of thiosulfate and its oxidation products such as common polythionates, sulfite and sulfate. Direct and indirect UV detection techniques were investigated. The optimized separations of UV absorbing S2O3(2-), S4O6(2-), S5O6(2-) and S6O6(2-) anions were carried out in 5 mmol l(-1) (NH4)2SO4, 5 mmol l(-1) KH2PO4 electrolyte at pH 5.0, with direct UV detection at 214 nm. All analytes were well resolved in less than 4 min. Analysis of S2O3(2-), S4O6(2-), SO4(2-) and SO3(2-) ions can be performed in 5 mmol l(-1) H2CrO4, 1 mmol l(-1) hexamethonium hydroxide electrolyte neutralized with triethanolamine to pH 8.0, using indirect UV detection at 254 nm. However, the detection sensitivity for tetrathionate was poor. Other polythionates can not be detected at all because of their high absorbance even at 254 nm. The developed CE method was applied for the monitoring of sulfur species in spent fixing solutions during the electrolytic oxidation.     

A fluorescence-based sequence-specific primer PCR for the screening of HLA-B(*)57:01

Abacavir (ABC) is an antiretroviral drug highly effective in the treatment of HIV, but its intake can cause severe hypersensitivity reaction (HSR). A strong association between HLA-B(*)57:01 and ABC HSRs was reported by several studies, which demonstrated that HLA-B(*)57:01 screening had a 100% negative predictive value and that it could accurately identify patients at high risk of ABC HSRs. We propose a new sequence-specific primer PCR assay based on fluorescence detection through CE which is highly sensitive, allowing the use of non-infective sources of DNA such as saliva and buccal swabs, in addition to blood and reproducible, allowing automation of the analytical process. The results of our study were first compared with a standard sequence-specific primer PCR technique and reported a concordance of 100%, and then a blind external validation further confirmed the accuracy of our method.     

重铬酸钾容量法测定铁矿石中亚铁含量方法的改进

建立了以邻菲罗啉(Phen)、氢氟酸(HF)和硫酸(H2 SO4)为溶剂溶解试样,用重铬酸钾滴定法测定铁矿中亚铁含量的新方法.在强酸(H2 SO4)介质中,Fe2与邻菲罗啉和氟离子形成稳定的络合物,有效地防止了亚铁离子的氧化.在硼酸、硫磷混酸溶液中,以重铬酸钾溶液滴定,并对溶样过程以及滴定过程中的一些条件进行了优化.方法用于铁矿中氧化亚铁的测定,经过国家标准样品以及单位管理样品分析数据对比,方法的重现性较好,相对标准偏差(RSD)＜1％,方法无需在铂金坩埚进行熔样,具有准确度高、重现性好、简单、快速、经济等优点,在实际应用中得到满意的结果.     

Fluorometric determination of sulfite and nitrite in aqueous samples using a novel detection unit of a microfluidic device.

On-chip fluorescence determination of sulfite and nitrite with N-(9-acridinyl)maleimide (NAM) and 2,3-diaminonaphthalene (DAN) has been developed using a novel fluorescence detection unit for microchip analysis. Usually, these fluorescence reagents are derivatized and detected separately in microchip analysis because different fluorescence wavelengths are emitted. The proposed fluorescence detection unit has optical fibers with no optical filter, and plural wavelengths of fluorescence were detected sensitively, even in the microchip. In this study, the simultaneous determination of sulfite and nitrite in environmental samples was performed with a polymer microchip analysis system. The calibration curves of sulfite and nitrite showed linear relations (R2 = 0.998 (sulfite) and R2 = 0.990 (nitrite)), and the relative standard deviations (RSD) for 4 runs were 2.1% (20 microM sulfite) and 1.3% (20 microM nitrite), respectively. The proposed method was applied to the recovery test of sulfite and nitrite in environmental samples.     

Chemiluminescence determination of sulfite in sugar and sulfur dioxide in air using Tris(2,2'-bipyridyl)ruthenium(II)-permanganate system

A chemiluminescence (CL) detection for the determination of sulfite using the reaction of Ru(bipy)(3)(2+) (bipy=2,2'-bipyridyl) -SO(3)(2-)-KMnO(4) is described. The concentration of sulfite is proportional to the CL intensity from 5.0x10(-8) to 1.25x10(-4) mol l(-1). The limit of detection is 2.5x10(-8) mol l(-1) and the relative standard deviation is 4.9% for the 2x10(-5) mol l(-1) sulfite solution in six repeated measurements. This method has been successfully applied to the determination of sulfite in sugar and sulfur dioxide in air by using triethanolamine (TEA) as the absorbent material.     

Theoretical and experimental studies of the spin trapping of inorganic radicals by 5,5-dimethyl-1-pyrroline N-oxide (DMPO). 3. Sulfur dioxide, sulfite, and sulfate radical anions

Radical forms of sulfur dioxide (SO(2)), sulfite (SO(3)(2-)), sulfate (SO(4)(2-)), and their conjugate acids are known to be generated in vivo through various chemical and biochemical pathways. Oxides of sulfur are environmentally pervasive compounds and are associated with a number of health problems. There is growing evidence that their toxicity may be mediated by their radical forms. Electron paramagnetic resonance (EPR) spin trapping using the commonly used spin trap, 5,5-dimethyl-1-pyrroline N-oxide (DMPO), has been employed in the detection of SO(3)(?-) and SO(4)(?-). The thermochemistries of SO(2)(?-), SO(3)(?-), SO(4)(?-), and their respective conjugate acids addition to DMPO were predicted using density functional theory (DFT) at the PCM/B3LYP/6-31+G**//B3LYP/6-31G* level. No spin adduct was observed for SO(2)(?-) by EPR, but an S-centered adduct was observed for SO(3)(?-)and an O-centered adduct for SO(4)(?-). Determination of adducts as S- or O-centered was made via comparison based on qualitative trends of experimental hfcc's with theoretical values. The thermodynamics of the nonradical addition of SO(3)(2-) and HSO(3)(-) to DMPO followed by conversion to the corresponding radical adduct via the Forrester-Hepburn mechanism was also calculated. Adduct acidities and decomposition pathways were investigated as well, including an EPR experiment using H(2)(17)O to determine the site of hydrolysis of O-centered adducts. The mode of radical addition to DMPO is predicted to be governed by several factors, including spin population density, and geometries stabilized by hydrogen bonds. The thermodynamic data supports evidence for the radical addition pathway over the nucleophilic addition mechanism.     

Polynuclear cobalt(II/III) sulfites: synthesis, structure, and magnetic properties of the octanuclear cluster (NH4)11(Li subset[Co4IICo4III(SO3)16(NH3)8]).10H2O encapsulating a lithium cation

Partial oxidation of an aqueous solution of CoIICl(2).6H2O with (NH4)6[Mo7VIO24].4H2O in the presence of (NH4)2SO3.H2O and LiCl, at pH approximately 5.3, leads to isolation of the octanuclear cluster (NH4)11(Li subset[Co4IICo4III(SO3)16(NH3)8].10H2O), 1. The structure of the anion of 1 consists of a central [Co4II], almost ideal square planar unit, and a pair of symmetry-related CoIII dimers above and below the Co4II plane grafting onto the tetramer by 16 bridging sulfite groups. The [Co8(SO3)16(NH3)8]12- cluster encapsulates a lithium cation which lies at the center of the Co4II square.     

Novel spectrofluorimetric method for the determination of sulfite with rhodamine B hydrazide in a micellar medium

A novel spectrofluorimetric method for the determination of sulfite using rhodamine B hydrazide as fluorogenic reagent in the presence of polyoxyethylene sorbitan monooleate (Tween 80) surfactant micelles is described. The method is based on the mixture of sulfite with rhodamine B hydrazide, a colorless, non-fluorescent substance in Tween 80 surfactant micelles which gives rhodamine B-like fluorescence emission. The fluorescence intensity increase is linearly related to the concentration of sulfite in the range 5-800 ng ml⁻¹ with a detection limit of 1.4 ng ml⁻¹ (3σ). The optimal conditions for the detection of sulfite are evaluated and the possible detection mechanism is also discussed. The method has been successfully applied to the determination of total sulfite in wines and compares well with the standard iodimetric method.     

高效液相色谱法测定食品中抗氧化剂BHA,BHT,PG

 用反相高效液相色谱法同时测定了食品中抗氧化剂丁基羟基茴香醚（ＢＨＡ）、二丁基羟基甲苯（ＢＨＴ）和焦性没食子酸丙酯（ＰＧ）。样品用正己烷提取，氮气吹干，水－乙醇（１４，Ｖ／Ｖ）溶解残留物，经０．５μｍ滤膜过滤，直接进样。方法简便、快速、回收率高、重现性好。     

Speciation of Co(II), Co(III), and Cu(II) in ethylenediamine solutions by capillary electrophoresis

A capillary electrophoretic (CE) method for the speciation of Co(II), Co(III), and Cu(II) in electroless copper-plating baths containing ethylenediamine (En) has been developed. The method is based on the selective pre-capillary derivatization of Co(II) with 1,10-phenanthroline (Phen) followed by CE separation of stable [CoPhen(3)](2+), [CoEn(3)](3+), and [CuEn(2)](2+) chelates. The proposed derivatization procedure protects Co(II) from oxidation by dissolved oxygen and enables rapid determination of all three metal species within a single run. The optimized separations were carried out in a fused silica capillary (57 cmx75-microm I.D.) filled with an ethylenediamine sulfate electrolyte (20 mmol L(-1) H(2)SO(4), pH 7.0 with En, applied voltage +30 kV) using direct UV detection at 214 nm. The detection limits for a signal-to-noise ratio of 3 and 10 s, hydrodynamic injections were 5x10(-6) mol L(-1) for Cu(II), 1x10(-6) mol L(-1) for Co(III), and 4x10(-7) mol L(-1) for Co(II). Application of the method to the speciation of Co(II), Co(III), and Cu(II) in copper-plating bath samples is also demonstrated.