分子印迹电位型传感器快速检测猪尿液中的克伦特罗

以盐酸克伦特罗为模板分子,采用沉淀聚合法合成了克伦特罗的分子印迹聚合物,并以其为离子载体,制得分子印迹聚合物膜克伦特罗离子选择性电极。在最优实验条件下,电极对克伦特罗阳离子的检出限可达7.0×10-8mol/L,线性范围为1.0×10-7～1.0×10-4mol/L,能斯特斜率为55.7 mV/decade。此电极具有优越的选择性、快速的响应时间以及良好的稳定性;已成功应用于实际猪尿样品中克伦特罗的测定,加标回收率为98%～107%,检测时间小于3 min。     

邻菲咯啉冠醚衍生物为载体的伯胺药物电极及机理研究

合成了邻菲咯啉-18-冠-6等四种含邻菲咯啉结构的冠醚化合物, 并用作载体制备伯胺电极, 以苄胺为模型化合物, 研究了电极特性, 并制备了测试美西律药物的选择性电极。研究了实验条件对电极性能的影响。用正交多项式回归法优化电极的膜组成。苄胺电极的线性范围1.0×10^-5~0.1mol/L, 斜率55.6mV/pc, 检测下限2.0×10^-6mol/L。美西律电极的线性范围6.0×10^-6~0.1mol/L, 检测下限8.0×10^-7mol, 斜率58.0mV/pc。同时研究了冠醚推动伯胺穿透大块液膜的传输行为。     

二(乙基黄原酸基)金属配合物为中性载体高选择性碘离子电极的研究

本文研究了二(乙基黄原酸基)金属配合物为中性载体的阴离子选择性电极,其中二(乙基黄原酸基)钴(Ⅱ)对碘离子有高的选择性, 且电极呈现反Hofmeister行为, 其选择次序是: I^->SCN^->NO2^->Br^->ClO4^->SO4^2^->NO3^->Cl^-, 采用交流阻抗和光谱分析技术研究了电极的响应机理, 并将电极用于药品分析,结果令人满意。     

Determination of SCN- in urine and saliva of smokers and non-smokers by SCN(-)-selective polymeric membrane containing a nickel(II)-azamacrocycle complex coated on a graphite electrode.

The construction, performance characteristics, and application of a novel polymeric membrane coated on a graphite electrode with unique selectivity towards SCN- are reported. The electrode was prepared by incorporating Ni(II)-2,2,4,9,9,11-hexamethyltetraazacyclotetradecanediene perchlorate into a plasticized poly(vinyl chloride) membrane. The influences of membrane composition, pH and foreign ions were investigated. The electrode displays a near Nernstian slope (-57.8 mV decade-1) over a wide concentration range of 1 x 10(-7)-1 x 10(-1) M of SCN- ion. The electrode has a detection limit of 4.8 x 10(-8) M (2.8 ng/cm3) SCN- and shows response times of about 15 s and 120 s for low to high and high to low concentration sequences, respectively. The proposed sensor shows high selectivity towards SCN- over several common organic and inorganic anions. The electrode revealed a great enhancement in selectivity coefficients and detection limit for SCN-, in comparison with the previously reported electrodes. It was successfully applied to the direct determination of SCN- in milk and biological samples, and as an indicator electrode in titration of Ag+ ions with thiocyanate.     

Cesium-selective membrane electrode based on a recently synthesized 16-membered macrocyclic diamide

A PVC membrane sensor for the Cs+ ion based on 1,5-diaza-2,3,4-naphthyl-8,11,14-trioxacyclohexadecane-6,16-dione (L) has been prepared. The sensor has a linear dynamic range of 5.0 x 10(-1) - 6.9 x 10(-6) mol L(-1), a Nernstian slope of 59.5 +/- 0.8 mV decade(-1), and a detection limit of 4.7 x 10(-6) mol L(-1). It has a fast response time of <15 s and can be used for at least 8 weeks without any considerable divergence in potentials. The selectivity of the proposed electrode relative to alkali, alkaline earth, and transition metal ions was comparatively good. The electrode could be used in the pH range 4.5-11.0.     

新型安培检测毛细管电泳微系统

将电极、６ｃｍ分离毛细管、缓冲池、检测池集成于８．４×５．０ｃｍ有机玻璃片上,制作了一个毛细管电泳微系统。以碳纤维微盘电极作为工作电极,采用三电极体系柱端检测了１×１０－４ｍｏｌ／Ｌ多巴胺（ＤＡ）,具有良好的重现性,检测限３．６×１０－８ ｍｏｌ／Ｌ,线性范围５×１０－７～１×１０－４ｍｏｌ／Ｌ,并在该系统上分离了邻苯二酚（ＣＡ）和多巴胺的混合物。     

Optimization of polymeric triiodide membrane electrode based on clozapine-triiodide ion-pair using experimental design

Central composite design (CCD) and response surface methodology (RSM) were developed as experimental strategies for modeling and optimization of the influence of some variables on the performance of a new PVC membrane triiodide ion-selective electrode. This triiodide sensor is based on triiodide-clozapine ion-pair complexation. PVC, plasticizers, ion-pair amounts and pH were investigated as four variables to build a model to achieve the best Nernstian slope (59.9 mV) as response. The electrode is prepared by incorporating the ion-exchanger in PVC matrix plasticized with 2-nitrophenyl octal ether, which is directly coated on the surface of a graphite electrode. The influence of foreign ions on the electrode performance was also investigated. The optimized membranes demonstrate Nernstian response for triiodide ions over a wide linear range from 5.0 x 10(-6) to 1.0 x 10(-2)mol L(-1) with a limit of detection 2.0 x 10(-6) mol L(-1) at 25 degrees C. The electrodes could be used over a wide pH range 4-8, and have the advantages of easy to prepare, good selectivity and fast response time, long lifetime (over 3 months) and small interferences from hydrogen ion. The proposed electrode was successfully used as indicator electrode in potentiometric titration of triiodide ions and ascorbic acid.     

Simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional ion-selective electrodes in series

An on-line automated system for the simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional calcium-selective and fluoride-selective membrane electrodes as sensors in series is described. Samples (30 μl) are injected into a TISAB II (pH=5.50) carrier solution as an ionic strength adjustment buffer. The sample-buffer zone formed is first channeled to a fluoride-selective membrane electrode and then via the calcium-selective membrane electrode to the reference electrodes. The system is suitable for the simultaneous on-site monitoring of calcium (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 1.94×10⁻⁶ mol l⁻¹ recovery 99.22%, RSD<0.5%) and fluoride (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 4.83×10⁻⁶ mol l⁻¹ recovery 98.63%, RSD=0.3%) at a sampling rate of 60 samples h⁻¹.     

Highly selective thiocyanate poly(vinyl chloride) membrane electrode based on a cadmium-Schiff's base complex

A PVC membrane electrode based on a cadmium-salen (N,N'-bis-salicylidene-1,2-ethylenediamine) complex as an anion carrier is described. The electrode has an anti-Hofmeister selectivity sequence with a preference for thiocyanate at pH 1.5-11.0. It has a linear response to thiocyanate from 1.0 x 10(-6) to 1.0 x 10(-1) mol L(-1) with a slope of 59.1 +/- 0.2 mV per decade, and a detection limit of 7 x 10(-7) mol L(-1). This electrode has high selectivity for thiocyanate relative to many common organic and inorganic anions. The proposed sensor has a fast response time of approximately 15 s. It was applied to the determination of thiocyanate in a milk sample.     

硫杂冠醚PVC膜汞（Ⅱ）离子选择电极的研制

以硫杂冠醚为活性物质的PVC膜汞(Ⅱ)离子选择电极的研究近年已有报道,我们曾报道二茂铁硫杀冠醚PVC膜汞(Ⅱ)离子选择电极的研制。并根据硫和汞的软硬酸碱相亲性,设计并合成了8个新型硫杂冠醚。本文以它们为活性物质研制PVC膜汞(Ⅱ)离子选     

Thiocyanate ion selective electrode based on bis(N-3-methylphenyl salicylidenaminato)copper(Ⅱ) ionophore

In this work a PVC membrane electrode based on bis(N-3-methyl phenyl salicylidenaminato)copper(II)as ionophore was prepared.The electrode was tested by inorganic anions and showed good selectivity for thiocyanate ion.This sensor showed Nerstian behavior with a slope of a-59.3 mV per decade at 25℃.The proposed electrode exhibited a wide linear range from 1.0 × 10~(-6) mol/L to 1.0× 10~(-1) mol/L with a detection limit of 5.0×10~(-7) mol/L.The electrode response was independent of pH in the range of 4.0-10.0.The response time is about 9-21s,and the electrode can be used for over 60 days without considerable deterioration.The prepared sensor was applied as an indicator electrode in potentiometric titration of SCN with Ag~+ ion and to determine the thiocyanate in samples of urine and saliva.     

基于壳聚糖/Ru（bpy）2+3/SiO2纳米粒子电化学发光传感器用于尿酸的检测

利用反相微乳液法制备了壳聚糖-Ru(bpy)2+3-SiO2复合纳米粒子,采用Nafion/MCNT复合膜技术实现了对复合纳米粒子有效而稳定的固定,从而制备了电化学发光传感器,实现了对尿酸的检测。在0.1 mol/L PBS缓冲溶液(pH 7.4)中,当尿酸与修饰电极作用15 min时,电化学发光强度与尿酸浓度(1.0×10-10~1.0×10-5 mol/L)的负对数呈良好的线性关系,线性方程为IECL=-709.52-202.74lgC,相关系数R=0.9936,检出限为6.0×10-12 mol/L。传感器表现出良好的重现性与稳定性,对1.0×10-8 mol/L尿酸平行测定11次,发光强度的相对标准偏差为2.9%,测定尿酸实际样品的加标回收率在98.5%~103.5%之间。     

A Neutral Carrier Membrane Calcium-Sensitive Electrode with Wide Working pH Range

Abstract

A poly(vinyl chloride) (PVC) membrane calcium-sensitive electrode based on a new type of synthetic carrier 1,7-di[2-(1-phenylazo)naphtyl]-1,4,7-trioxaheptan is introduced. This electrode exhibited Nernstian response over the concentration range 1.0×10^?1 - 3.0×10^?8 mol/L Ca²⁺ with a slope of 28.8 mV/pCa in calcium ion buffer solutions. The detection limit for calcium ion was 1.0X10^?8 mol/L. The response time varied from 10 to 30 seconds. The working pH range for the electrode was 3.5 - 12.3 when the concentration of Ca²⁺ was 10^?3 mol/L. The lifetime of the electrode was proved to exceed 8 months. It was applied successfully in the determination of calcium ion in river water, mineral water and cosmetic. A method for the determination of total calcium in urine was developed.     

Iodide-selective polymeric membrane electrode based on copper(Ⅱ) bis(N-2-bromophenylsalicyldenaminato) complex

A PVC membrane electrode based on copper（Ⅱ） bis（N-2-bromophenylsalicyldenaminato） as ionophor was prepared.The ion selective electrode was tested by inorganic anions and showed a good selectivity for iodide ion.This sensor exhibited Nernstian behavior with a slope of—57.8 mV per decade at 25℃.The proposed electrode showed a linear range from 1.0×10⁵ to 1.0×10^-1 mol/L with a detection limit of 5.0×10^-6 mol/L.The electrode response was independent of pH in the range of 3.0- 10.0.The proposed sensor was applied to determine the iodide in water and antiseptic samples.     

A comparative study of liquid and solid inner contact roxatidine acetate ion-selective electrode membranes

A comparative study was conducted using two designs of a roxatidine acetate (ROX)-selective electrode; a conventional liquid inner contact called electrode A and a graphite-coated solid contact called electrode B. The fabrication of electrodes was based on roxatidine-tetraphenylborate (ROX-TPB) as an ion-association complex in a PVC matrix using different plasticizers. Electrode A has a linear dynamic range of 2.2×10-5 mol/L to 1.0×10-2 mol/L, with a Nernstian slope of 54.7 mV/decade and a detection limit of 1.4×10-6 mol/L. Electrode B shows linearity over the concentration range of 1.0×10-6 mol/L to 1.0×10-2 mol/L, with a Nernstian slope of 51.2 mV/decade and a limit of detection of 1.1×10-7 mol/L which is remarkably improved as a result of diminishing ion fluxes in this solid contact, ion-selective electrode. The proposed sensors display useful analytical characteristics for the determination of ROX in bulk powder and its pharmaceutical formulation. The present electrodes show clear discrimination of ROX from several inorganic, organic ions, sugars, some common drug excipients and the degradation product (3-[3-(1-piperidinyl methyl) phenoxy] propyl amine) of ROX. Furthermore, the proposed electrodes were utilized for the determination of ROX in human plasma, where electrode B covers drug Cmax which indicated its applicability to pharmacokinetic, bioavailability and bioequivalent studies. The results obtained by the proposed electrodes were statistically analyzed and compared with those obtained by a reported HPLC method. No significant difference for either accuracy or precision was observed.     

Electrochemical oxidation behavior of colchicine on a graphene oxide-Nafion composite film modified glassy carbon electrode

An electrochemical sensor, based on a graphene oxide (GO)-Nafion composite film modified glassy carbon electrode (GCE), was developed and used for detection of trace amounts of colchicine. Owing to the large surface area, good conductivity of GO and good affinity of Nafion, the sensor exhibited excellent electrocatalytic activity for the oxidation of colchicine, displaying a wide linear response from 5.0 × 10(-8) to 2.0 × 10(-5) mol L(-1) and a low detection limit of 1.5 × 10(-8) mol L(-1) in 0.1 mol L(-1) H(2)SO(4) solution. And this modified electrode exhibited a superior immunity from epinephrine, dopamine and ascorbic acid interference. The method was also applied successfully to detect colchicine in medicinal tablets.     

Comparative electrochemical study of new self-assembled monolayers of 2-{[(Z)-1-(3-furyl)methylidene]amino}-1-benzenethiol and 2-{[(2-sulfanylphenyl)imino]methyl}phenol for determination of dopamine in the presence of high concentration of ascorbic acid and uric acid

The comparative electrochemical behavior of self-assembled monolayers of two Schiff's bases, 2-{[(Z)-1-(3-furyl)methylidene]amino}-1-benzenethiol (FMAB) and 2-{[(2-sulfanylphenyl)imino]methyl}phenol (SIMP) on a bare gold electrode (Au FMAB SAM-modified electrode and Au SIMP SAM-modified electrode, respectively), was investigated by means of cyclic voltammetry and electrochemical impedance spectroscopy in a 0.1 mol L(-1) KCl solution that contains 5.0 × 10(-3) mol L(-1) [Fe(CN)(6)](3-/4-). The results revealed that the modified electrodes showed an electrocatalytic activity toward the anodic oxidation of dopamine by a marked enhancement in the current response and lower overpotential (60 and 90 mV for the Au FMAB and Au SIMP SAM-modified electrodes, respectively) in phosphate buffer solution at pH 6.0. The Au SIMP SAM-modified electrode was applied successfully to the determination of dopamine in the presence of a high concentration of ascorbic acid. Selective detection was realized in total elimination of ascorbic acid response-a method different from the ones based on the potential separations. The detection limit of dopamine was 5.0 × 10(-8) mol L(-1) in a linear range from 1.0 × 10(-6) to 1.2 × 10(-4) mol L(-1) in the presence of 1.0 × 10(-3) mol L(-1) ascorbic acid. The interference studies also showed that the Au SIMP SAM-modified electrode exhibited good selectivity in the presence of a large excess of uric acid and could be employed for the determination of dopamine in pharmaceutical formulations, plasma samples and human urine with adequate selectivity and precision.     

基于石墨烯分子印迹电化学传感器测定芦丁

将石墨烯(GR)滴涂至裸Au电极表面,并以邻氨基酚为功能单体,芦丁为模板分子,制备了芦丁分子印迹膜电化学传感器,利用循环伏安法(CV)和差分脉冲伏安法(DPV)对制得的传感器进行了电化学性能研究,并且对制备条件和测定条件进行了优化。结果表明,与裸Au电极相比,该GR修饰的Au电极在[Fe(CN)_6]~(3-/4-)溶液中峰电流明显增大,显著提高了芦丁分子印迹传感器的灵敏度。在最优实验条件下,基于GR分子印迹电化学传感器在4.40×10~(-6)~2.80×10~(-4) mol/L范围内呈良好的线性关系,检测限为1.46×10~(-6) mol/L。用该传感器测定了黑茶中芦丁的含量,获得较好结果。     

桑色素分子印迹传感器的制备与应用

以邻氨基酚( o-AP)为功能单体,桑色素为模板分子,基于分子间的相互作用力,在金电极表面电聚合制备具有特异性识别孔穴的桑色素分子印迹传感器膜。采用循环伏安法( CV)、差分脉冲伏安法( DPV)等研究了分子印迹膜的性能和分子印迹效应。探索了聚合膜配比及聚合扫描圈数对传感器性能的影响,优化了洗脱时间和印迹时间。比较了此传感器对其结构相似物的选择性响应,发现其对桑色素检测具有良好的选择性。在最佳实验条件下,此传感器对桑色素浓度定量测定范围为0.05~1.70μmol/L,线性方程为I(μA)=1.0800lgc(mol/L)+9.3599, R=0.9934,检出限为0.01μmol/L。用此传感器测定黑茶样品中桑色素的含量,加标回收率为104.0%~108.0%。     

Used gold nano-particles as an on/off switch for response of a potentiometric sensor to Al(III) or Cu(II) metal ions

The potentiometric response of a carbon paste electrode modified with silica sol-gel and mercaptosuccinic acid (MSA) in the presence and absence of gold nano-particles was studied. The results showed that the electrode with gold nano-particles was responded to Al(3+) ions as a hard metal ion. On the other hand, the electrode without gold nano-particles was responded to copper ions as a soft metal ion. The electrodes without and with gold nano-particles exhibits a Nernstian slope of 29.1 and 19.2 mV decade(-1) for copper and aluminum ions over a wide concentration range of 4.3×10(-7)-1.0×10(-2) and 4.5×10(-7)-1.6×10(-3) mol L(-1), respectively. The detection limits of electrodes were 4.0×10(-7) and 1.6×10(-7) mol L(-1) for copper and aluminum ions, respectively.