反相乳液中Ag/TiO2纳米杂化粒子的制备及其SERS效应

在反相乳液的微环境中用一步反应法制备了Ag/TiO2纳米杂化粒子,并用TEM,SPS,XPS及XRD等方法进行了表征.结果表明,Ag粒子(5-15nm)已镶嵌在TiO2(30-50nm)结构中,并且具有SERS活性.     

Preparation of Au/TiO2 nanocomposites and their catalytic activity for DPPH radical scavenging reaction

Au/TiO2 nanocomposites have been prepared by UV photolysis or chemical reduction of a Au(III) complex formed on a spherical or a rodlike TiO2 support, and their catalytic activity for 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging reaction was investigated. The chemical reduction with dimethylamine borane (DMAB) provided smaller gold nanoparticles than those synthesized by UV photolysis. Type of the TiO2 also affected the size of gold particles; smaller gold particles were deposited on the spherical TiO2 support than on rodlike one. For the radical scavenging reaction, the Au/TiO2 nanocomposites prepared by chemical reduction exhibited a higher catalytic activity than those photochemically prepared, and rodlike TiO2 provided a higher activity than spherical one. The effects of preparation methods and type of TiO2 supports on the catalytic activity are discussed.     

二氧化钛纳米微粒的制备与光催化活性

本文采用溶液－凝胶法制备了粒径为１０－２０ｎｍ左右的二氧化钛纳米微粒。用ＸＲＤ研究了二氧化钛溶胶的热处理过程,研究表明温度在４７３Ｋ－６７３Ｋ左右ＴｉＯ２向量 粒呈不规整锐钛矿结构,粒径约为１０－２０ｎｍ。在８７３Ｋ左右ＴｉＯ２微粒出现锐钛矿与金红石型混晶结构。     

Controllable and repeatable synthesis of thermally stable anatase nanocrystal-silica composites with highly ordered hexagonal mesostructures

In this article, we report a controllable and reproducible approach to prepare highly ordered 2-D hexagonal mesoporous crystalline TiO2-SiO2 nanocomposites with variable Ti/Si ratios (0 to infinity). XRD, TEM, and N2 sorption techniques have been used to systematically investigate the pore wall structure, and thermal stability functioned with the synthetic conditions. The resultant materials are ultra highly stable (over 900 degrees C), have large uniform pore diameters (approximately 6.8 nm), and have high Brunauer-Emmett-Teller specific surface areas (approximately 290 m2/g). These mesostructured TiO2-SiO2 composites were obtained using titanium isopropoxide (TIPO) and tetraethyl orthosilicate (TEOS) as precursors and triblock copolymer P123 as a template based on the solvent evaporation-induced co-self-assembly process under a large amount of HCl. Our strategy was the synchronous assembly of titanate and silicate oligomers with triblock copolymer P123 by finely tuning the relative humidity of the surrounding atmosphere and evaporation temperature according to the Ti/Si ratio. We added a large amount of acidity to lower condensation and polymerization rates of TIPO and accelerate the rates for TEOS molecules. TEM and XRD measurements clearly show that the titania is made of highly crystalline anatase nanoparticles, which are uniformly embedded in the pore walls to form the "bricked-mortar" frameworks. The amorphous silica acts as a glue linking the TiO2 nanocrystals and improves the thermal stability. As the silica contents increase, the thermal stability of the resulting mesoporous TiO2-SiO2 nanocomposites increases and the size of anatase nanocrystals decreases. Our results show that the unique composite frameworks make the mesostructures overwhelmingly stable; even with high Ti/Si ratios (> or =80/20) the stability of the composites is higher than 900 degrees C. The mesoporous TiO2-SiO2 nanocomposites exhibit excellent photocatalytic activities (which are higher than that for commercial catalyst P25) for the degradation of rhodamine B in aqueous suspension. The excellent photocatalytic activities are ascribed to the bifunctional effect of highly crystallized anatase nanoparticles and high porosity.     

高纯纳米氧化钛的制备及催化活性

以工业级硫酸钛为原料,在酸性环境下以EDTA作为络合剂,采用控制沉淀法制备高纯度纳米TiO2。考察了pH值、反应温度、煅烧温度等工艺条件对TiO2颗粒晶型、大小和分布影响。利用TEM、XRD、ICP等手段对产物进行表征,TiO2纯度超过99.9%,粒径为10-20nm,分布均匀。经过对其光催化降解苯酚反应活性实验,结果表明样品具有较好的光催化活性。     

Sol-gel low-temperature synthesis of stable anatase-type TiO2 nanoparticles under different conditions and its photocatalytic activity

In this work, TiO(2) nanoparticles in anatase phase was prepared by sol-gel low temperature method from titanium tetra-isopropoxide (TTIP) as titanium precursor in the presence of acetic acid (AcOH). The effects of synthesis parameters such as AcOH and water ratios, sol formation time, synthesis and calcination temperature on the photocatalytic activity of TiO(2) nanoparticles were evaluated. The resulting nanoparticles were characterized by X-ray diffraction, UV-Vis reflectance spectroscopy, transmission electron microscopy and Brunauer-Emmett-Teller techniques. Photocatalytic activity of anatase TiO(2) nanoparticles determined in the removal of C. I. Acid Red 27 (AR27) under UV light irradiation. Results indicate that with increasing AcOH/TTIP molar ratio from 1 to 10, sol formation time from 1 to 3 h and synthesis temperature from 0 to 25°C, increases crystallite size of synthesized nanoparticles. It was found that optimal conditions for low temperature preparation of anatase-type TiO(2) nanoparticles with high photocatalytic activity were as follows: TTIP:AcOH:water molar ratio 1:1:200, sol formation time 1 h, synthesis temperature 0°C and calcination temperature 450°C.     

Synthesis of titanium dioxide nanoparticles with mesoporous anatase wall and high photocatalytic activity

Mesoporous titanium dioxide nanosized powder with high specific surface area and anatase wall was synthesized via hydrothermal process by using cetyltrimethylammonium bromide (CTAB) as surfactant-directing agent and pore-forming agent. The resulting materials were characterized by XRD, nitrogen adsorption, FESEM, TEM, and FT-IR spectroscopy. The as-synthesized mesoporous TiO2 nanoparticles have mean diameter of 17.6 nm with mean pore size of 2.1 nm. The specific surface area of the as-synthesized mesoporous nanosized TiO2 exceeded 430 m2/g and that of the samples after calcination at 600 degrees C still have 221.9 m2/g. The mesoporous TiO2 nanoparticles show significant activities on the oxidation of Rhodamine B (RB). The large surface area, small crystalline size, and well-crystallized anatase mesostructure can explain the high photocatalytic activity of mesoporous TiO2 nanoparticles calcined at 400 degrees C.     

Synthesis of uniform anatase TiO2 nanoparticles by gel-sol method. 3. Formation process and size control

Uniform anatase-type TiO(2) nanoparticles were prepared by the gel-sol process from a condensed Ti(OH)(4) gel preformed by the hydrolysis of a Ti-triethanolamine (TEOA) complex. The particle size of the anatase TiO(2) was increased from ca. 5 to 30 nm with pH increasing from 0.6 to 12 by aging the Ti(OH)(4) gel at 140 degrees C for 72 h, while the yield of the anatase TiO(2), 100% below pH 9.6, started to decrease from pH 10, to 67% at pH 11.5 and only 9% at pH 12.2. These results reveal a significant reduction of the nucleation rate of the anatase TiO(2) with increasing pH, as is explained by the reduction of the concentration of a precursor complex, Ti(OH)(3)(+), and the adsorption of hydroxide ion onto the embryos of TiO(2). Triethanolamine appeared to enhance the pH effect on the nucleation rate of anatase TiO(2) particles by adsorption onto their embryos, leading to the wide range of the size control. Triethanolamine was also found to act as a shape controller of the anatase TiO(2) particles for yielding ellipsoidal particles from Ti(OH)(4) gel at a relatively high pH above 11. The particle size was also controlled by seeding of anatase TiO(2). Moreover, the seeding experiment suggested that the rate-determining step of the gel-sol process was not the dissolution of the hydroxide gel, but the deposition of the monomeric precursor from the solution phase.     

A one-step process for the antimicrobial finishing of textiles with crystalline TiO2 nanoparticles

Titanium oxide (TiO(2)) nanoparticles (NPs) in their two forms, anatase and rutile, were synthesized and deposited onto the surface of cotton fabrics by using ultrasonic irradiation. The structure and morphology of the nanoparticles were analyzed by using characterization methods such as XRD, TEM, STEM, and EDS. The antimicrobial activities of the TiO(2)-cotton composites were tested against Escherichia coli (gram-negative) and Staphylococcus aureus (gram-positive) strains, as well as against Candida albicans. Significant antimicrobial effect was observed, mainly against Staphylococcus aureus. In addition, the combination of visible light and TiO(2) NPs showed enhanced antimicrobial activity.     

微乳法制备纳米TiO2 /SiO2的结构及光催化研究

Nanosized TiO₂ and TiO₂/SiO₂ particles were prepared by hydrolysis of tetrabutyl titanate (TBOT) and tetraethyl orthosilicate (TEOS) in the TX-100 reverse microemulsion. These particles were characterized by TG-DSC, XRD, FTIR, TEM，N₂ adsorption-desorption. Their photocatalytic activity was tested by degradation of methyl orange. The result shows that TiO₂/SiO₂ nanoparticles are with a monodispersed spherical phase and a uniform size distribution，and TiO₂ particles are dispersed on the surface of SiO₂. The band for Ti-O-Si vibration in FTIR was observed, the Ti-O-Si bond increased the stability of anatase TiO₂, suppressed the phase transformation of titania from anatase to rutile. And due to the addition of SiO₂, the average size of titania decreased from 38 nm in pure TiO₂ to 5 nm in TiO₂/SiO₂. It was found, under UV light irradiation, TiO₂/SiO₂ particles showed higher activity than pure TiO₂, and TiO₂/SiO₂(1/1) particles showed the highest photocatalytic activity on the photocatalytic decomposition of methyl orange, which was influenced by crystal structure, particle size, crystallinity and Surface area Characteristics.     

Structural feature and catalytic performance of Cu species distributed over TiO2 nanotubes

Copper oxide was deposited on tubular TiO2 via Cu2+ introduction into a titanate nanotube aggregate followed by calcination. The titanate has a layered structure allowing Cu intercalation and can readily transform into anatase TiO2 via calcination for condensation of the constituting layers. The activity of the tubular catalysts, with a Cu content of 2 wt %, in selective NO reduction with NH3 was compared with those of other 2 wt % Cu/TiO2 catalysts using TiO2 nanoparticles as the support. The Cu species supported on the nanotubes showed a higher activity than those supported on the nanoparticles. X-ray absorption near-edge structure (XANES) analysis showed that the Cu species on all the TiO2 supports are in the +2 state. Extended X-ray absorption fine structure (EXAFS) investigations of these catalysts reflected higher degrees of CuO dispersion and Cu2+ dissolution into the TiO2 lattice for the tubular Cu/TiO2 catalysts. Absence of CuO bulk detection by a temperature-programmed reduction analysis for the tubular catalysts confirmed the high CuO-dispersion feature of the tubular catalysts. The dissolution of Cu2+ to form a CuxTi1-xO2 type of solid solution was improved by using an in-situ ion-intercalation method for Cu deposition on the nanotubes. A fraction as high as 40% for Cu2+ dissolution was obtained for the tubular catalysts while only 20% was obtained for the particulate catalysts. The CuxTi1-xO2 species were considered one form of the active sites on the Cu/TiO2 catalysts.     

Rutile TiO2 nanowires on anatase TiO2 nanofibers: a branched heterostructured photocatalysts via interface-assisted fabrication approach

A water-dichloromethane interface-assisted hydrothermal method was employed to grow rutile TiO(2) nanowires (NWs) on electrospun anatase TiO(2) nanofibers (NFs), using highly reactive TiCl(4) as precursor. The water-dichloromethane interface inhibited the formation of rutile NWs in water phase, but promoted the selective radial growth of densely packed rutile NWs on anatase NFs to form a branched heterojunction. The density and length of rutile NWs could be readily controlled by varying reaction parameters. A formation mechanism for the branched heterojunction was proposed which involved (1) the entrapment of rutile precursor nanoparticles at water-dichloromethane interface, (2) the growth of rutile NWs on anatase NFs via Ostwald ripening through the scavengering of interface-entrapped rutile nanoparticles. The heterojunction formed at anatase NF and rutile NW enhanced the charge separation of both under ultraviolet excitation, as evidenced by photoluminescence and surface photovoltage spectra. The branched TiO(2) heterostructures showed higher photocatalytic activity in degradation of rodamine B dye solution than anatase NFs, and the mixture of anatase NFs, and P25 powders, which was discussed in terms of the synergistic effect of enhanced charge separation by anatase-rutile heterojunction, high activity of rutile NWs, and increased specific area of branched heterostructures.     

板式纳米碳纤维负载二氧化钛光催化复合材料的制备及降解甲基橙的研究

以板式纳米碳纤维为载体,采用酸性氧化法对载体进行预处理之后,使用钛酸异丙酯为钛源,高温水热法制备了二氧化钛/纳米碳纤维复合光催化剂,并考察了其对甲基橙的光催化去除能力及循环反应性能.复合材料中二氧化钛含量通过改变前驱体组成进行调节.材料的结构性能通过氮气吸附、X射线衍射(XRD)、能谱分析仪(EDS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、热重分析仪(TG-DSC)等测试技术进行了表征.结果表明,锐钛矿型的二氧化钛以纳米颗粒形式均匀分散在纳米碳纤维表面,从而形成了高度分散的二氧化钛/碳纤维纳米复合材料.另外,复合系统中中孔吸附作用的存在,与纳米二氧化钛的光催化产生协同作用,增强了复合材料在紫外光照射下对于水溶液中甲基橙的去除能力.在光照射下反应120 min时,不同担载量样品对甲基橙的去除率最高可达80.1%,不同煅烧温度样品最高可达79.2%.此外,光催化剂有着良好重复利用性能,3次循环反应后对甲基橙去除率仍可保持80.0%.     

Gold nanoparticles located at the interface of anatase/rutile TiO2 particles as active plasmonic photocatalysts for aerobic oxidation

Visible-light irradiation (λ > 450 nm) of gold nanoparticles loaded on a mixture of anatase/rutile TiO(2) particles (Degussa, P25) promotes efficient aerobic oxidation at room temperature. The photocatalytic activity critically depends on the catalyst architecture: Au particles with <5 nm diameter located at the interface of anatase/rutile TiO(2) particles behave as the active sites for reaction. This photocatalysis is promoted via plasmon activation of the Au particles by visible light followed by consecutive electron transfer in the Au/rutile/anatase contact site. The activated Au particles transfer their conduction electrons to rutile and then to adjacent anatase TiO(2). This catalyzes the oxidation of substrates by the positively charged Au particles along with reduction of O(2) by the conduction band electrons on the surface of anatase TiO(2). This plasmonic photocatalysis is successfully promoted by sunlight exposure and enables efficient and selective aerobic oxidation of alcohols at ambient temperature.     

Enhanced photocatalytic degradation of C.I. Basic Violet 2 using TiO2-SiO2 composite nanoparticles

In this report, TiO(2) -SiO(2) composite nanoparticles were prepared by the thermal hydrolysis method using titanium tetrachloride and tetraethylorthosilicate as TiO(2) and SiO(2) precursors, respectively. The prepared nanoparticles were characterized by X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption/desorption and UV-Vis diffuse reflectance spectroscopy (DRS). The results indicated that, in comparison with pure TiO(2), TiO(2)-SiO(2) composite nanoparticles had a higher thermal stability, which prevents phase transformation from anatase to rutile. In addition, the TiO(2)-SiO(2) nanoparticles had a higher specific surface area, larger pore volume, greater band gap energy and smaller crystallite size. Thus, the surface area of TiO(2)-40% SiO(2) composite nanoparticles was about 17 times higher than that of pure TiO(2) nanoparticles. The photocatalytic activity of TiO(2)-SiO(2) composite nanoparticles in the photodegradation of C.I. Basic Violet 2 was investigated. The photodegradation rate of Basic Violet 2 using TiO(2)-40% SiO(2) nanoparticles calcined at 600°C was much faster than that using pure TiO(2) and Degussa P25 TiO(2) by 10.9 and 4.3 times, respectively. The higher photoactivity of the TiO(2)-SiO(2) composite nanoparticles was attributed to their higher surface area, larger pore volume, greater band-gap energy and smaller crystallite size compared with pure TiO(2).     

制备均一形貌的长二氧化钛纳米管

在温和的水热条件下,用碱溶液处理不同粒径的锐钛矿相和金红石相二氧化钛 纳米粉体,得到了不同形貌的二氧化钛纳米管,并用TEM,XRD,FT-Raman和BET等 对其进行了表征。金红石相的超细纳米晶有利于形成均一形貌的纳米管,用粒径仅 为7.2 nm的金红石相纳米粉体为前驱体得到了长度为500 nm的长二氧化钛纳米管。 用纳米晶反应活性对晶粒尺寸的依赖性及晶相稳定性解释了长纳米管的形成机理。     

Synthesis of TiO2 photocatalysts with abundant surface defects using a TiO2@NaCl precursor

TiO2 nanoparticles have been synthesized by using a TiO2@NaCl core-shell structure as the precursor. The surface defects were well preserved by the NaCl shell, and therefore high oxygen adsorption capacity was observed. After the NaCl shell was removed, the resulting pure TiO2 nanoparticles were of anatase phase and uniform size of around 20?24 nm. The presence of an abundance of surface defects contributes to the high photocatalytic activity of the synthesized materials, and the TiO2 materials obtained from the TiO2@NaCl precursor can be used as efficient photocatalysts for degradation of rhodamine B under UV light irradiation.     

WC/TiO2纳米复合材料的制备及其电催化性能

以TiCl4为原料, 采用溶胶水解法合成了金红石型纳米TiO2颗粒, 并以其为载体制备了WC/TiO2纳米复合材料. 采用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线能谱(EDS)等手段分析了WC/TiO2纳米复合材料的晶相组成和表面形貌. 结果显示样品是由WC, TiO2和W组成, 纳米WC颗粒均匀地包覆在TiO2的表面, 并与TiO2构成了WC/TiO2纳米复合材料. 采用循环伏安法和计时电流法研究了WC/TiO2纳米复合材料对硝基苯的电催化性能. 结果表明, WC/TiO2纳米复合材料对硝基苯的电催化活性和电化学稳定性均优于介孔结构碳化钨(meso-WC)和纳米WC颗粒(part-WC).     

Photocatalytic synthesis of silver nanoparticles stabilized by TiO2 nanorods: a semiconductor/metal nanocomposite in homogeneous nonpolar solution

A novel colloidal approach toward semiconductor/metal nanocomposites is presented. Organic-soluble anatase TiO(2) nanorods are used for the first time to stabilize Ag nanoparticles in optically clear nonpolar solutions in the absence of specific ligands for silver. Metallic silver is generated upon UV illumination of deaerated TiO(2) solutions containing AgNO(3). The Ag nanoparticles can be obtained in different size-morphological regimes as a function of the irradiation time, due to light-induced photofragmentation and ripening processes. A mechanism for the colloidal stabilization of the silver nanoparticles is tentatively suggested, which regards the TiO(2) nanorods as inorganic stabilizers, thus acting in the same manner as conventional surfactant molecules. The proposed photocatalytic approach offers a convenient method for producing TiO(2)/Ag nanocomposite systems with a certain control over the metal particle size without the use of surfactants and/or additives. Stable colloidal TiO(2)-nanorod-stabilized Ag nanoparticles can be potentially available for a number of applications that require "clean" metal surfaces, such as homogeneous organic catalysis, photocatalysis, and sensing devices.     

A versatile strategy to fabricate hydrogel-silver nanocomposites and investigation of their antimicrobial activity

In this study, hydrogel-silver nanocomposites have been synthesized by a unique methodology, which involves formation of silver nanoparticles within swollen poly (acrylamide-co-acrylic acid) hydrogels. The formation of silver nanoparticles was confirmed by transmission electron microscopy (TEM) and surface plasmon resonance (SPR) which was obtained at 406 nm. The TEM of hydrogel-silver nanocomposites showed almost uniform distribution of nanoparticles throughout the gel networks. Most of the particles, as revealed from the particle-size distribution curve, were 24-30 nm in size. The X-ray diffraction pattern also confirmed the face centered cubic (fcc) structure of silver nanoparticles. The nanocomposites demonstrated excellent antibacterial effects on Escherichia coli (E. coli). The antibacterial activity depended on size of the nanocomposites, amount of silver nanoparticles, and amount of monomer acid present within the hydrogel-silver nanocomposites. It was also found that immersion of plain hydrogel in 20 mg/30 ml AgNO(3) solution yielded nanocomparticle-hydrogel composites with optimum bactericidal activity.