Instrumental methods and challenges in quantifying polybrominated diphenyl ethers in environmental extracts: a review

Increased interest in the fate, transport and toxicity of polybrominated diphenyl ethers (PBDEs) over the past few years has led to a variety of studies reporting different methods of analysis for these persistent organic pollutants. Because PBDEs encompass a range of vapor pressures, molecular weights and degrees of bromine substitution, various analytical methods can lead to discrimination of some PBDE congeners. Recent improvements in injection techniques and mass spectrometer ionization methods have led to a variety of options to determine PBDEs in environmental samples. The purpose of this paper is therefore to review the available literature describing the advantages and disadvantages in choosing an injection technique, gas chromatography column and detector. Additional discussion is given to the challenges in measuring PBDEs, including potential chromatographic interferences and the lack of commercial standards for higher brominated congeners, which provides difficulties in examining degradation and debromination of BDE congeners, particularly for BDE 209.     

Determination of polybrominated diphenyl ethers in human milk samples in the Czech Republic: Comparative study of negative chemical ionisation mass spectrometry and time-of-flight high-resolution mass spectrometry

In the Czech Republic no study on the levels of brominated flame retardants in human milk has been conducted, yet. In the first step analytical method for determination of PBDEs in this bioindicator matrix was implemented. Liquid–liquid extraction (LLE) (hexane, diethyl ether), followed by gel permeation chromatography was employed for isolation of PBDEs. Identification and quantification of PBDEs was carried out by GC–MS operated in negative chemical ionisation (NCI). Two mass spectrometric technologies, one employing quadrupole and the other one high resolution (HR) time-of-flight (TOF) analyzer, etc. were used in our study. Detection limits (LODs) obtained by quadrupole analyzer ranged from 0.02 to 0.05 ng g⁻¹ lipid weight, using high resolution time-of-flight analyzer LODs were significantly lower, ranging from 0.002–0.005 ng g⁻¹ lipid weight, what enabled detection of minor PBDE congeners.

Within this pilot study 103 breast milk samples, obtained from mothers living in Olomouc region, were examined. Ten PBDE congeners were determined. All samples examined till now contained PBDEs residues, the dominating contaminant representing this group was congener BDE 47. In most of analysed samples levels of this compound ranged from 0.2 to 2 ng g⁻¹ of lipid weight. Three exceptionally contaminated samples, containing levels of PBDEs 5–10 times higher than other samples, were found.     

Determination of polybrominated diphenyl ethers in indoor dust standard reference materials

Polybrominated diphenyl ethers (PBDEs) have been measured for the first time in three different indoor dust Standard Reference Materials (SRMs) prepared by the National Institute of Standards and Technology (NIST). Two of these, SRM 2583 (Trace Elements in Indoor Dust) and SRM 2584 (Trace Elements in Indoor Dust), have been certified previously for lead and other inorganic constituents. A third, SRM 2585 (Organics in Indoor Dust), is a new indoor dust reference material prepared by NIST which will be certified for various organic compounds (polycyclic aromatic hydrocarbons, pesticides and polychlorinated biphenyls) in 2005 including certified concentrations for 16 individual PBDE congeners and reference values for an additional three PBDE congeners. Dust SRMs were analyzed for 30 PBDE congeners using high-resolution gas chromatography combined with low-resolution mass spectrometry operated in both negative chemical ionization (GC/ECNI–MS) and electron impact ionization (GC/EI–MS) modes. Sensitivity was an order of magnitude higher using GC/ECNI–MS relative to GC/EI–MS. These SRMs have been characterized and compared to the three PBDE commercial products (pentaBDE, octaBDE and decaBDE). PentaBDE and DecaBDE were present in all three SRMs and were the dominant commercial products, making up approximately 33% and 58%, respectively. Recent studies suggest that house dust may be a leading source of human exposure to PBDEs. These SRMs are the first reference materials with certified concentrations for PBDEs, which will aid in validating future measurements of PBDEs in house dust and other similar matrices. Electronic Supplementary Material Supplementary material is available for this article at http://dx.doi.org/ 10.1007/s00216-005-0227-y     

Comprehensive two-dimensional gas chromatography of polybrominated diphenyl ethers

Comprehensive two-dimensional gas chromatography with micro electron-capture detection (GCxGC-muECD) was evaluated for the separation of 125 polybrominated diphenyl ethers (PBDEs). From among the six column combinations that were evaluated, DB-1x007-65HT was found to be the most suitable because of: (i) the highest number of BDE congeners separated; (ii) the least decomposition of higher brominated congeners; and (iii) the most suitable maximum operating temperature. The separation of the 125 BDE congeners from five hydroxy- and two methoxy-BDEs and nine other brominated flame retardants (polybrominated biphenyls, tetrabromobisphenol-A, methyl-tetrabromobisphenol-A and hexabromocyclododecane) was also studied. Fluorinated BDEs were found to be valuable internal standards for the determination of BDEs because of their very similar physico-chemical properties and excellent separation from the parent BDEs, mainly in the second dimension. GCxGC-time-of-flight MS and GCxGC-muECD were shown to be useful tools to identify decomposition products of nona- and deca-substituted BDEs, which are formed during the GC run. Three nona-BDEs were shown to be the major decomposition products of BDE 209.     

Investigation of reagent gases for the positive chemical ionization of select polybrominated diphenyl ethers

Polybrominated diphenyl ethers (PBDEs) fall into the class of compounds known as brominated flame retardants and their incorporation in a multitude of products is responsible for saving numerous lives. However, toxicology studies have alerted researchers to the potential adverse health effects that may develop as a result of prolonged or extreme exposure to these compounds. Frequent disposal and subsequent leaching has focused concern on environmental concentrations and current reports cite increasing levels. Method development continues in support of this research and the present work examines the feasibility of utilizing gas chromatography ion trap mass spectrometry operating in positive ion chemical ionization mode. In the evaluation of reagents for chemical ionization (methane, methanol and acetonitrile), comparative results of all three reagents demonstrated more difficult protonation as the number of bromine atoms increased. Methane, possessing the lowest proton affinity, provided the highest response for the analytes. Further, when methane chemical ionization was compared to electron impact ionization, the tetra-congener showed approximately 8× greater sensitivity and the penta- and hexa-congeners demonstrated approximately 2× greater. CI parameters, such as ionization and reaction times, were optimized to provide the highest analyte response and this was followed by the investigation of the employment of MSⁿ. In the this mode, optimal excitation amplitude delivered sufficient fragmentation while maintaining maximum signal, yielding final instrument detection limits in the sub µg L^{− 1} range.     

动物肝脏中九种多溴联苯醚残留量的GC—NCI／MS分析

建立了动物肝脏中9种PBDEs残留量的气相色谱-负化学离子源/质谱(GC-NCI/MS)的分析方法。动物肝脏样品经V(正己烷)∶V(丙酮)=1∶1超声辅助提取,中性与酸性硅胶层析柱净化和V(正已烷)∶V(CH2Cl2)=1∶1洗脱和浓缩后,以PCB-103为内标物,采用GC-NCI/MS的选择离子监测方式(SIM)对其中的9种PBDEs残留量进行了定性与定量分析。当动物肝脏空白样品的加标质量浓度为5.0、20.0μg/kg(PBDE-183为6.0、24.0μg/kg)时,9种PBDEs的平均加标回收率为75.1%~88.2%,相对标准偏差为3.3%~7.9%,方法检出限均小于0.07μg/kg;线性范围除PBDE-183为0.12~600.0μg/kg外,其余8种PBDEs为0.1~500.0μg/kg,相关系数都大于0.9993。所建立的分析方法已用于5种动物肝脏的8个样品中9种PBDEs残留量的分析。     

环境样品中多溴联苯醚分析方法的研究进展

多溴联苯醚(PBDEs)作为一类应用广泛的溴代阻燃剂,具有持久污染性、易于从被应用产品中脱离出来进入环境介质等特性,目前已对全球环境造成了严重危害.近年来针对PBDEs分析检测技术的报道愈来愈多,然而PBDEs不仅含量极低,而且所处基体复杂,因此样品前处理技术成为分析PBDEs类化合物的一个重要步骤,受到科学工作者的广泛重视.本文作者综述了近年来分析环境样品中PBDEs的样品前处理技术和分析检测方法的研究进展,为更好的发展准确、灵敏、快速的分析方法提供重要的参考.     

Analytical performance of a triple quadrupole mass spectrometer compared to a high resolution mass spectrometer for the analysis of polybrominated diphenyl ethers in fish

Polybrominated diphenyl ethers (PBDEs) are a class of flame retardants used globally in many consumer products and industrial applications. Traditionally, gas chromatography–high resolution mass spectrometry (GC–HR-MS) is the method of choice for analysis of PBDEs in environmental samples because it offers high sensitivity and selectivity, resulting in less interferences. However, the specificity offered by gas chromatography-triple quadrupole tandem mass spectrometry (GC–QQQ-MS/MS), operated in selected reaction monitoring mode, provides a more affordable alternative to GC–HR-MS for the analysis of PBDEs in complex environmental samples. In this study, an analytical method was developed for the analysis of 41 PBDE congeners in fish using GC–QQQ-MS/MS. Results from the analysis of three fish species [lake trout (Salvelinus namaycush), yellow perch (Perca flavescens), and round goby (Neogobius melanostomus)] using GC–QQQ-MS/MS were compared with those obtained by GC–HR-MS. These species were selected because they represent varying levels of lipid-rich matrix and contaminant loads. Instrumental limits of detection for the GC–QQQ-MS/MS ranged from 0.04 pg to 41 pg, whereas those for the GC–HR-MS ranged from 5 pg to 85 pg. The PBDE values obtained from these two methods were highly correlated, R² values >0.7, for all three fish species, supporting the suitability of GC–QQQ-MS/MS for analysis of PBDEs in fish with varying fat content.     

Microwave-assisted extraction followed by headspace solid-phase microextraction and gas chromatography with mass spectrometry detection (MAE-HSSPME-GC-MS/MS) for determination of polybrominated compounds in aquaculture samples

This paper describes the first validated method for the extraction, purification and determination of trace levels of a number of pollutants of growing concern, including polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs), in aquaculture feeds and products. The new procedure comprises microwave-assisted extraction (MAE; optimized, using a central composite experimental design, to 15 min at 85 °C in 14 mL of 1:1 hexane/dichloromethane), and concentration by headspace solid-phase microextraction (HSSPME), and separation/quantification by gas chromatography with mass spectrometry detection (GC-MS/MS). The method was validated on the reference materials IAEA-406 and WMF-01. Limits of detection for fourteen of the fifteen analytes considered range from 10 to 600 pg g⁻¹, and limits of quantification from 50 pg g⁻¹ to 1.9 ng g⁻¹. Linear ranges, accuracies and precisions are reported.     

“One-shot” analysis of polybrominated diphenyl ethers and their hydroxylated and methoxylated analogs in human breast milk and serum using gas chromatography-tandem mass spectrometry

The presence of polybrominated diphenyl ethers (PBDEs) and their hydroxylated (OH-BDE) and methoxylated (MeO-BDE) analogs in humans is an area of high interest to scientists and the public due to their neurotoxic and endocrine disrupting effects. Consequently, there is a rise in the investigation of the occurrence of these three classes of compounds together in environmental matrices and in humans in order to understand their bioaccumulation patterns. Analysis of PBDEs, OH-BDEs, and MeO-BDEs using liquid chromatography-mass spectrometry (LC-MS) can be accomplished simultaneously, but detection limits for PBDEs and MeO-BDEs in LC-MS is insufficient for trace level quantification. Therefore, fractionation steps of the phenolic (OH-BDEs) and neutral (PBDEs and MeO-BDEs) compounds during sample preparation are typically performed so that different analytical techniques can be used to achieve the needed sensitivities. However, this approach involves multiple injections, ultimately increasing analysis time. In this study, an analytical method was developed for a “one-shot” analysis of 12 PBDEs, 12 OH-BDEs, and 13 MeO-BDEs using gas chromatography with tandem mass spectrometry (GC-MS/MS). This overall method includes simultaneous extraction of all analytes via pressurized liquid extraction followed by lipid removal steps to reduce matrix interferences. The OH-BDEs were derivatized using N-(t-butyldimethylsilyl)-N-methyltrifluoroacetamide (TBDMS-MTFA), producing OH-TBDMS derivatives that can be analyzed together with PBDEs and MeO-BDEs by GC-MS/MS in “one shot” within a 25-min run time. The overall recoveries were generally higher than 65%, and the limits of detection ranged from 2 to 14 pg in both breast milk and serum matrices. The applicability of the method was successfully validated on four paired human breast milk and serum samples. The mean concentrations of total PBDEs, OH-BDEs, and MeO-BDEs in breast milk were 59, 2.2, and 0.57 ng g⁻¹ lipid, respectively. In serum, the mean total concentrations were 79, 38, and 0.96 ng g⁻¹ lipid, respectively, exhibiting different distribution profiles from the levels detected in breast milk. This “one-shot” GC-MS/MS method will prove useful and cost-effective in large-scale studies needed to further understand the partitioning behavior, and ultimately the adverse health effects, of these important classes of brominated flame retardants in humans.     

Selective pressurized liquid extraction of polybrominated diphenyl ethers in fish

A fast and simple method for the analysis of polybrominated diphenyl ethers (PBDEs) in fish samples was developed using a one-step extraction and clean-up by means of pressurized liquid extraction (PLE) combined with gas chromatography-ion trap tandem mass spectrometry (GC-ITMS-MS). The selective PLE method provided to obtain ready-to-analyse extracts without any additional clean-up step, using a sorbent as fat retainer inside the PLE cell. Several PLE operating conditions, such as solvent type, extraction temperature and time, number of cycles and type of fat retainer, were studied. Using Florisil as fat retainer, maximum recoveries of PBDEs (83-108%) with minimum presence of matrix-interfering compounds were obtained using a mixture of n-hexane:dichloromethane 90:10 (v/v) as solvent, an extraction temperature of 100 °C and a static extraction time of 5 min in combination with three static cycles. Quality parameters of the method were established using standards and fish samples. Limits of detection and quantification ranged from 10 to 34 pg g⁻¹ wet weight and between 34 and 68 pg g⁻¹ wet weight, respectively. In addition, good linearity (between 1 and 500 ng ml⁻¹) and high precision (RSD % < 15%) were achieved. The method was validated using the standard reference material SRM-1945 (whale blubber) and was then applied to the analysis of PBDEs in fish samples.     

Brominated flame retardants in the European chemicals policy of REACH-Regulation and determination in materials

The EU REACH legislation will require the registration of 30,000 currently marketed chemicals, including the main commercial BFRs in use (Deca-BDE, HBCD and TBBP-A). Much of the data needed for registration are already available, thanks to risk assessments of continued production and use already undertaken in the EU. Within the authorisation, substitution by less hazardous chemicals is encouraged. Both qualitative and quantitative methods for the analysis of flame-retarded polymers are needed in order that the identity and concentration of the BFRs can be established and compliance with regulations including the RoHS Directive demonstrated. These are reviewed.     

Headspace solid-phase microextraction gas chromatography tandem mass spectrometry for the determination of brominated flame retardants in environmental solid samples

A headspace solid-phase microextraction gas chromatography coupled with tandem mass spectrometry (HSSPME-GC-MS-MS) methodology for determination of brominated flame retardants in sediment and soil samples is presented. To the best of our knowledge, this is the first time that SPME has been applied to analyze polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in environmental solid samples. Analyses were performed using 0.5-g solid samples moisturized with 2 mL water, employing a polydimethylsiloxane (PDMS) fiber coating, exposed to the headspace at 100 °C for 60 min. Several types of environmental solid samples were included in this study and the extraction efficiency was related to the organic matter content of the sample. Calibration was performed using real samples, and the method showed good linearity over a wide concentration range, precision, and afforded quantitative recoveries. The obtained detection limits were in the sub-ng g⁻¹ for all the target analytes in both samples. The proposed procedure was applied to several marine and river sediments and soils, some of which were found to contain PBDEs at concentrations in the ng g⁻¹ level; BDE-47, BDE-100, and BDE-99 were the major congeners detected. The proposed method constitutes a rapid and low-cost alternative for the analysis of the target brominated flame retardants in environmental solid samples, since the clean-up steps, fractionation, and preconcentration of extracts inherent to the classical multi-step solvent extraction procedures are avoided.      

Determination of polybrominated diphenyl ethers in environmental standard reference materials

Standard reference materials (SRMs) are valuable tools in developing and validating analytical methods to improve quality assurance standards. The National Institute of Standards and Technology (NIST) has a long history of providing environmental SRMs with certified concentrations of organic and inorganic contaminants. Here we report on new certified and reference concentrations for 27 polybrominated diphenyl ether (PBDE) congeners in seven different SRMs: cod-liver oil, whale blubber, fish tissue (two materials), mussel tissue and sediment (two materials). PBDEs were measured in these SRMs, with the lowest concentrations measured in mussel tissue (SRM 1974b) and the highest in sediment collected from the New York/New Jersey Waterway (SRM 1944). Comparing the relative PBDE congener concentrations within the samples, we found the biota SRMs contained primarily tetrabrominated and pentabrominated diphenyl ethers, whereas the sediment SRMs contained primarily decabromodiphenyl ether (BDE 209). The cod-liver oil (SRM 1588b) and whale blubber (SRM 1945) materials were also found to contain measurable concentrations of two methoxylated PBDEs (MeO-BDEs). Certified and reference concentrations are reported for 12 PBDE congeners measured in the biota SRMs and reference values are available for two MeO-BDEs. Results from a sediment interlaboratory comparison PBDE exercise are available for the two sediment SRMs (1941b and 1944).     

Optimization of quadrupole ion storage mass spectrometric conditions for the analysis of selected polybrominated diphenyl ethers. Comparative approach with negative chemical ionization and electron impact mass spectrometry

Gas chromatography coupled to quadrupole ion storage mass spectrometry (QISTMS) operating in the non-resonant mode is presented as an innovative approach for the analysis of selected polybrominated diphenyl ethers (PBDEs). Although reductions in complexity and time needed for optimization are achieved in comparison with the resonant option, precise adjustment of the mass spectrometric conditions is required. Differences in isolation and fragmentation patterns of target species with degree of bromination were observed. The reliability of the method was confirmed by using standard solutions through the evaluation of certain quality parameters such as accuracy (92-108%), injection repeatability and reproducibility (coefficient of variation below 10% and 15%, respectively). Detection limits ranged from 62 to 621 fg, providing sensitivity similar to that of negative chemical ionisation (NCIMS) and greater than that of electron ionization mass spectrometry. The applicability of QISTMS method to real samples and matrix effects were evaluated through the analysis of some PBDE congeners in a sewage sludge sample from a Spanish waste-water treatment plant. Comparable results were obtained using QISTMS and NCIMS. According to these observations, QISTMS performed in the non-resonant mode may constitute a low-cost, rapid and reliable alternative to high-resolution devices for the analysis of selected PBDEs in environmental samples.     

Determination of polybrominated diphenyl ethers in marine biological tissues using microwave-assisted extraction

Growing concern on the environmental impact of polybrominated diphenyl ethers (PBDEs) has created the need for rapid and quality assured analytical methods to quantify PBDEs in a spectrum of matrix types. This study presents the first validated method for the quantification of major PBDE congeners (47, 99 and 100) in marine biological tissues using microwave-assisted extraction (MAE). The recovery of polychlorinated biphenyls and various organochlorine pesticides has also been ascertained. Analytical accuracy, precision, limits of detection and cleanup efficiency were evaluated for PBDE congeners, and empirical data justifies the use of MAE for the extraction and analysis of PBDEs in biological matrices. MAE was also compared to Soxhlet extraction efficiency for PBDEs in the standard reference materials SRM2978 and SRM1588a and gave comparable results (<15% variation).     

Microwave-assisted extraction for qualitative and quantitative determination of brominated flame retardants in styrenic plastic fractions from waste electrical and electronic equipment (WEEE)

A fast method for the determination of brominated flame retardants (BFRs) in styrenic polymers using microwave-assisted extraction (MAE) and liquid chromatography with UV detection (HPLC-UV) was developed. Different extraction parameters (extraction temperature and time, type of solvent, particle size) were first optimised for standard high-impact polystyrene (HIPS) samples containing known amounts of tetrabromobisphenol A (TBBPA) and decabromodiphenyl ether (Deca-BDE). Complete extraction of TBBPA was achieved using a combination of polar/non-polar solvent system (isopropanol/n-hexane) and high extraction temperatures (130 °C). Lower extraction yields were, however, obtained for Deca-BDE, due to its high molecular weight and its non-polar nature. The developed method was successfully applied to the screening of BFRs in standard plastic samples from waste electrical and electronic equipment (WEEE); TBBPA could be fully recovered, and Deca-BDE could be identified, together with minor order polybrominated diphenyl ether (PBDE) congeners.     

Developments in the use of chromatographic techniques in marine laboratories for the determination of halogenated contaminants and polycyclic aromatic hydrocarbons

Chromatography has been an important tool in marine laboratories. Since the 1960s, marine laboratories have been involved in the analysis of polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), polycyclic aromatic hydrocarbons (PAHs), and brominated flame retardants (BFRs). Column chromatography and liquid chromatography (LC) techniques have been used, mainly in the clean-up phase, while gas chromatography (GC) has been used extensively in the final determination of these contaminants. Developments have been observed from the use of packed GC columns, via capillary columns to the use of heart-cut multi-dimensional GC and comprehensive multi-dimensional GC. The progress made in interlaboratory studies and the availability of certified reference materials are discussed.     

气相色谱-负离子化学源-质谱法分析禽蛋食品中10种多溴联苯和多溴联苯醚残留

建立了气相色谱-负离子化学源-质谱法(GC-NCI-MS)同时分析禽蛋食品中10种多溴联苯(PBBs)和多溴联苯醚(PBDEs)残留的分析方法。禽蛋食品用正己烷超声提取、浓硫酸酸化、中性和酸性硅胶层析柱净化和正己烷洗脱后,以PCB209为内标物,采用GC-NCI-MS的选择离子监测方式(SIM)分析;同时探讨了目标物PBDE100 NCI-MS特征离子的断裂机理。当禽蛋食品空白的加标质量浓度为5(3.5)和50(35)μg/kg时,加标回收率为75.2%～107%,相对标准偏差为2.3%～8.8%,方法检测限为0.14～0.39μg/kg,线性范围为1～250μg/kg,相关系数皆大于0.9991,方法已用于禽蛋食品中10种痕量PPBs和PBDEs残留的同时分析。     

Polybrominated diphenyl ethers (PBDEs) in marine sediment of Thermaikos Gulf,Greece

Polybrominated diphenyl ether (PBDE) concentrations were determined in marine sediment samples collected from 7 different locations around Thermaikos Gulf in north Greece. PBDEs were detected in all sampling sites and their average total concentration (ΣPBDEs) ranged from 0.26 to 4.92?ng?g^?1?d.w. Concentrations were an order of magnitude higher in locations outlining the inner part of the Gulf, which were also closer to industrial areas, sewage treatment plant discharges, the city's harbour and landfill area. These findings suggest pollution in the aquatic ecosystem from industrial and urban activities in the area. Congener profiles exhibit predominance of BDE-209, while concentrations of other PBDE congeners were usually lower, when compared to similar studies from other countries globally, indicating that Thermaikos Gulf is among the low-polluted areas. Statistical analysis showed significant differences among the higher polluted sampling stations. Statistically significant differences also existed between sampling stations with high and low PBDE concentrations. Correlations between congeners suggested local contamination sources; however, specific point sources of pollution were not established.