Understanding Creep Behavior of Semicrystalline Polymer via Coarse‐Grained Modeling

Understanding the deformational and failure behaviors of thermoplastic semicrystalline polymers is crucial due to the practical usages in various engineering applications. Taking isotactic polypropylene (iPP) as a semicrystalline polymer model system, atomistically informed coarse‐grained (CG) molecular dynamics (MD) simulations are employed to investigate the creep behavior of iPP. The simulations reveal that there exists a threshold stress of about 20.0 MPa, above which the maximum strain of iPP within the simulation time span increases dramatically. From the strain‐time analysis, it is observed that the iPP exhibits an initial elastic deformation stage and a subsequent plastic stage at lower stress levels, while a three‐stage creep behavior including a third fracture stage is observed at higher stress levels. Specifically, at lower stress levels, the bonded energy increases continuously as the chains stretch steadily, while the nonbonded energy shows an initial increase followed by a steady decrease due to the interchain sliding. At higher stress levels, both bonded and nonbonded energies change dramatically at the third stage, resulting from accelerated chain stretching, unfolding, sliding, and breaking. This study provides physical insight into the creep behavior of iPP at a fundamental molecular level and highlights the important role of microstructural evolution of chains in the deformation of semicrystalline polymer materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1779–1791     

Mechanical and thermo‐mechanical studies of double networks based on thermoplastic elastomers

A new approach to prepare and characterize double network elastomeric systems was investigated. A styrene‐ethylene‐co‐butylene‐styrene (SEBS) triblock copolymer system containing physical crosslinks was used to achieve a double network by additional crosslinking using ultra‐violet (UV) light. An ethylene–propylene–diene monomer (EPDM) terpolymer system containing chemical crosslinks was used to achieve a conventional double network using UV crosslinking. Properties from conventional monotonic tensile tests, dynamic mechanical analysis, and thermomechanical properties were investigated. These double network elastomers show a transition between competitive and collaborative behavior in their mechanical properties and lower coefficients of thermal expansion arising from a competition of the networks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 778–789, 2010     

Predictors of Cavitation in Glassy Polymers under Tensile Strain: A Coarse‐Grained Molecular Dynamics Investigation

The nucleation of cavities in a homogeneous polymer under tensile strain is studied in a coarse‐grained MD simulation. To establish a causal relation between local microstructure and the onset of cavitation, a detailed analysis of some local properties is presented. In contrast to common assumptions, the nucleation of a cavity is neither correlated to a local loss of density nor to stress at the atomic scale or the chain‐end density in the nondeformed state. Instead, a cavity in glassy polymers nucleates in regions that display a low bulk elastic modulus. Even if the localization of a cavity is not directly predictable from the initial configuration, the elastically weak zones identified in the initial state emerge as favorite spots for cavity formation.

     

Reorientation Dynamics of Chromophores in Photosensitive Polymers by Means of Coarse‐Grained Modeling

We study the photoisomerization of azobenzene chromophores embedded into a polymer matrix by using coarse‐grained simulations. Two types of beads are considered: t‐ and c‐beads, which are rich in trans and cis isomers, respectively. Simulations combine deterministic (molecular dynamics) and stochastic (random‐type switching) parts. The ratio between the characteristic times for photoinduced reorientation and for orientation relaxation is tuned to be of the order found in experiments. The essential features of the phenomenon: 1) the existence of a stationary state, and 2) anisotropic distribution of the orientations of t‐beads (orientation hole‐burning effect), are reproduced. We study population dynamics of c‐beads and the strength of the orientation hole burning, depending on the illumination wavelength and its intensity. The form of the reorientation potential of the mean force acting on the t‐beads is analyzed and its use is validated.     

Coarse‐Grained Simulations of Model Polymer Nanofibres

We describe the development of a coarse‐grained (CG) force field for nylon‐6 (polycaprolactam) and its application to the simulation of the structure and macromolecular dynamics within cylindrical fibres formed by this polymer, having diameters in the 14–28 nm range. Our CG model is based on the MARTINI force field for the non‐bonded interactions and on Boltzmann‐inverted gas‐phase atomistic simulations for intramolecular stretching and bending energies. The simulations are carried out on infinite, isolated nanofibres at temperatures of 300, 400 and 500 K, with different starting configurations. Starting from ordered chain‐extended configurations, we simulate the melting of the polymer in the nanofibres and, after cooling back to room temperature, its re‐crystallization in a chain‐folded lamellar configuration. This agrees with experimental observations on electrospun nylon‐6 nanofibres and demonstrated the suitability of the approach for the simulation of these systems. The effect of nanoscale confinement on the structure and dynamics of the polymer chains is extensively discussed.

     

Swelling and Tensile Properties of Tetra‐Polyethylene glycol via Coarse‐Grained Molecular Models

Coarse‐grained (CG) implicit‐solvent potentials are developed for tetra‐polyethylene glycol (PEG) at different water concentrations using the iterative Boltzmann inversion (IBI) technique. The resulting potentials are used to study the swelling and tensile properties of tetra‐PEG gels at various swelling degrees φ_m. Two types of network topologies are considered, one “ideal” with a defect‐free diamond connectivity and the other “realistic” as simulated from an experimentally based cross‐linking process. Equilibrium swelling results for the realistic Tetra‐PEG networks are consistent with available experimental data, while those for the ideal tetra‐PEG networks exhibit much larger swelling. The realistic networks have higher Young's modulus E _m at the same φ_m than ideal networks due to the presence of trapped entanglements. Uniaxial deformation results of realistic networks show that E _m increases with degree of swelling, in accord with experimental results. The Young's moduli of gels at different φ_m confirm that the CG potentials developed by IBI are most suited to predict swelling states commensurate with the φ_m values at which the potentials were calibrated. A more generic, coarser potential, based on matching the persistence length of atomistic PEG chains in water, is able to produce a similar swelling behavior of an ideal diamond network.

     

Influence of Carbon Black and Silica Filler on the Rheological and Mechanical Properties of Natural Rubber Compound

Rubber compounds are reinforced with fillers such as carbon black and silica. In general, filled rubber compounds shows smooth rheological behavior and mechanical properties. Variation in rheological behavior and mechanical properties was studied in terms of the filler composition using natural rubber compounds filled with both carbon black and silica CB/Si = 0/60, 20/40, 30/30, 40/20 and 60/0 phr (parts per hundred rubber is parts of any non-rubbery material per hundred parts of raw gum elastomer (rubbery material)). The rheological behaviour can be showed in measurement of Mooney viscosity and cure time. The Mooney viscosity of rubber compounds increase with the increasing the carbon black in the compounds. The compound filled with CB/Si of 30/30 and 60/0 showed abnormal rheological behaviour in which the cure time decreased suddenly and the increased at certain ratio during the measurement. The mechanical properties such as hardness, abrasion resistance and tensile stress at 300% elongation were studied. In the hardness and abrasion resistance measurement, the higher ratio CB/Si decrease contribution of silica, which resulting smaller of hardness value. Ratio CB/Si 40/20 gives an optimum filler blended. It is also clearly understood that higher abrasion resistance mainly due to the lower hardness value under the same condition. The tensile stress at 300% elongation of rubber compound increased with the increasing carbon black filler.     

Mechanical properties of gradient copolymers of styrene and n‐butyl acrylate

The mechanical properties of linear and V‐shaped compositional gradient copolymer of styrene and n‐butyl acrylate with composition of around 55 wt % styrene were investigated by comparing with their block copolymer counterparts. Compared with their block copolymer counterparts, the gradient copolymers showed lower elastic modulus, much larger elongation at break, and similar ultimate tensile strength at room temperature. This performance could be ascribed to that the local moduli continuously change from the hardest nanodomains to the softest nanodomains in the gradient copolymer, which alleviates the stress concentration during tensile test. Compared with the V‐shaped gradient (VG) copolymer, the linear gradient copolymer showed much higher elastic modulus but lower elongation at break. The mechanical properties of the gradient copolymers were more sensitive to the change in temperature from 9 °C to 75 °C. With recovery temperature increased from 10 °C to 60 °C, the strain recovery of VG copolymer would change steadily from 40% to 99%. However, the elastic recovery of linear and triblock copolymer was poor even at 60 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 860–868     

High‐Throughput Screening of Mechanical Properties on Temperature‐Gradient Polyurethaneurea Libraries

Combinatorial libraries of segmented polyurethaneurea with gradients in curing temperature were prepared and characterized using a novel high‐throughput mechanical instrument. Stress/strain profiles were taken at different temperature positions on the libraries, and a structure/property relationship between microstructure and mechanical properties was established by correlating the measured strength and strain at break to high‐throughput AFM and FT‐IR measurements on the same library. These results demonstrate the feasibility of rapid and accurate screening of mechanical properties, and their correlation to structure, by using gradient combinatorial polymer libraries.

Impact energy/thickness and elongation at break versus cure T for a T‐gradient SPUU library.     

Toughening of poly(L‐lactide)/multiwalled carbon nanotubes nanocomposite with ethylene‐co‐vinyl acetate

Poly(L ‐lactide)/multiwalled carbon nanotubes (PLLA/MWCNTs) nanocomposite recently attracts much attention because of its excellent comprehensive properties including improved thermostability, tensile strength, and conductivity. However, the nanocomposite exhibits similar brittleness compared with unmodified PLLA. In this work, a polar elastomer, that is, ethylene‐co‐vinyl acetate (EVA), was introduced into PLLA/MWCNTs nanocomposite. The selective distribution of MWCNTs and the effects of EVA on crystalline structure of PLLA were investigated using scanning electron microscope, transmission electron microscope, differential scanning calorimetry, and wide angle X‐ray diffraction. The results show that the presence of EVA induces the change of the distribution of MWCNTs in the nanocomposites, and consequently, the cold crystallization of PLLA is prevented. With the increase of EVA content, both the ductility and the impact resistance of PLLA/FMWCNTs are improved greatly, indicating the toughening effect of EVA on PLLA/MWCNTs nanocomposite. The decreased tensile strength and modulus can be compensated through annealing treatment. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

偶联剂对TATB造型粉表面性质及力学性能的影响

采用偶联技术制备TATB造型粉，研究了偶联剂加入前后TATB造型粉的表面行为及其力学性能。结果表明采用偶联技术能够改善TATB造型粉的力学性能和氟橡胶对TATB的粘附。其中，KH550是一种较为理想的改善TATB造型粉性能的偶联剂。     

Influence of the β‐Sheet Content on the Mechanical Properties of Aggregates during Amyloid Fibrillization

Amyloid fibrils associated with neurodegenerative diseases, such as Parkinson’s and Alzheimer’s, consist of insoluble aggregates of α‐synuclein and Aβ‐42 proteins with a high β‐sheet content. The aggregation of both proteins occurs by misfolding of the monomers and proceeds through the formation of intermediate oligomeric and protofibrillar species to give the final fibrillar cross‐β‐sheet structure. The morphological and mechanical properties of oligomers, protofibrils, and fibrils formed during the fibrillization process were investigated by thioflavin T fluorescence and circular dichroism in combination with AFM peak force quantitative nanomechanical technique. The results reveal an increase in the Young’s modulus during the transformation from oligomers to mature fibrils, thus inferring that the difference in their mechanical properties is due to an internal structural change from a random coil to a structure with increased β‐sheet content.     

Monte Carlo Simulations on Nanoparticles in Elastomers. Effects of the Particles on the Dimensions of the Polymer Chains and the Mechanical Properties of the Networks

Summary: Reinforcement of elastomers is modeled using Monte Carlo simulations on rotational isomeric state chains, to characterize their spatial configurations in the vicinity of filler particles. The resulting filler-perturbed distributions of the chain end-to-end distances are in agreement with experimental results gotten by neutron scattering. The use of these distributions in a standard molecular theory of rubberlike elasticity produces stress-strain isotherms for elongation that are consistent with available experimental results.     

Low‐temperature route to thermoplastic polyamide elastomers

Thermoplastic polyamide elastomers were obtained by polymerization of aminobenzoyl‐substituted telechelics derived from poly(tetrahydrofuran)‐diols (number‐average molecular weight: 1400 or 2000 g mol^?1) with several diacid dichlorides (terephthaloyl dichloride, 4,4′‐biphenyldicarbonyl dichloride, or 2,6‐naphthalenedicarbonyl dichloride) and chlorotrimethylsilane in N,N‐dimethylacetamide at 0–20 °C. The as‐prepared polymers had melting temperatures above 190 °C and exhibited elastic properties at room temperature, as evidenced by dynamic mechanical analysis and stress–strain measurements. The polymer with 2,6‐naphthalenedicarboxamide hard segments had the widest rubbery plateau within the series, the highest extension at break, and good recovery properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1449–1460, 2004     

Polyisobutylene‐based polyurethanes. IX. synthesis,characterization, and properties of polyisobutylene‐based poly(urethane‐ureas)

Polyisobutylene (PIB)‐based polyurethanes (PUs) exhibit unparalleled hydrolytic‐oxidative‐biologic stability and are melt processible, however, their mechanical (strength) properties are modest mainly due to insufficient H bonds. We posited and demonstrate that the ultimate properties of PIB‐PUs are enhanced, while their melt processibility is maintained, by the judicious introduction of urea linkages, i.e., strong bifurcated H bonds, in the chain. The incorporation of bifurcated H bonds in PIB‐PUs was achieved by using the conventional butane diol chain extender (CE) in combination with controlled amounts of amino alcohol as co‐chain extender (co‐CE). Polyurethanes containing both urethane and urea linkages are polyurethane‐ureas (PUU). Specifically, PIB‐PUUs prepared with PIB‐diol/MDI together with 80/20 mole % butane diol/amino butanol exhibited ～30 MPa tensile strength, ～550% elongation, ～80 Shore A hardness, and ～137 °C flow temperature. Other amino alcohols, i.e., amino ethanol, ‐propanol, and ‐hexanol, were less effective co‐CEs. ¹H‐NMR and FT‐IR spectroscopies indicate the presence of bifurcated H bonds in PIB‐PUUs prepared with CE/co‐CE combinations. Characterization by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and creep experiments also suggest bifurcated H bonds in PIB‐PUU. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2361–2369     

Influence of Proteins on the Mechanical Properties of Agro-Based Materials

Summary : A new biodegradable thermoplastic material based on a wheat flour by-product has been developed. The influence of protein content in wheat flour on the mechanical properties of the material has been investigated. For protein content between 4% and 10%, no influence of the protein content was evidenced, whereas beyond 10% w/w of proteins in the wheat flour, the mechanical properties of agro-based materials decrease, thus confirming the advantage of using a wheat flour by-product (i.e. with protein content below 8% w/w).     

Mechanical Properties and Structure of Zinc-Containing Latex-Silicate Composites

The sol-gel technology is highly efficient for improving mechanical and thermal properties of polydiene elastomers by creating in them additional inorganic networks composed mainly of silica or silicates. The incorporation of modifying Zn ions into polydiene latex-silica systems increases considerably their mechanical characteristics due to an increase of the interaction between the organic and inorganic networks. Interpenetrating polydiene-silica networks were prepared by cohydrolysis of tetraethoxysilane and zinc acetate in natural Qualitex or synthetic butadiene-styrene latexes and then by aging and drying the liquid compositions at room temperature and vulcanizing at 90°C. Their structure and properties were studied by the IR spectroscopy, TMA and by tensile testing of the prepared films. The studied system was shown to be extremely suitable for obtaining latex films with improved elastic and strength characteristics. For example, the elastic modulus values of the Qualitex films containing 2–5% SiO₂ and 0.1–0.2% ZnO, are 4–9 and 6–11 times higher than those of the films prepared without zinc and of the pure latex films respectively. The possible structure roles of zinc ions at various stages of film preparation and vulcanization are discussed on the base of the results of IR and TMA studies.