Bi‐directional organic light‐emitting diodes with nanoparticle‐enhanced light outcoupling

An effective method is presented for enhancing the outcoupling efficiency of translucent/bi‐directional organic light‐emitting diodes (TL/BD‐OLEDs) with a bottom indium tin oxide (ITO) anode and a top cathode comprised of a thin Ag layer covered with an organic capping layer. Upon insertion of a nanoparticle (NP)‐based scattering layer (NPSL) between the substrate and the ITO anode, the TL/BD‐OLEDs exhibit significantly enhanced external quantum efficiency (EQE) in both emission directions. Furthermore, the NPSL improves the color stability of the TL/BD‐OLEDs over a wide range of viewing angles. Simulations based on geometrical and statistical optics are performed to elucidate the mechanism by which the efficiency is enhanced and to establish strategies for further optimization. Simulations performed on the scattering layers with varying NP volume percentage reveal that the bottom‐side emission is governed by competition between waveguide‐mode extraction and backward scattering by NPs in the film, while the top‐side emission is largely dominated by the latter. Optimized bi‐directional OLEDs achieve a 1.64‐fold enhanced EQE compared to reference devices without NPSL.     

Thin film hexagonal gold grids as transparent conducting electrodes in organic light emitting diodes

Indium Tin Oxide (ITO) coated glass is currently the preferred transparent conducting electrode (TCE) for organic light emitting diodes (OLEDs). However, ITO has its drawbacks, not least the scarcity of Indium, high processing temperatures, and inflexibility. A number of technologies have been put forward as replacements for ITO. In this paper, an OLED based on a gold grid TCE is demonstrated, the light emission through the grid is examined, and luminance and current measurements are reported. The gold grid has a sheet resistance of 15 Ω□⁻¹ and a light transmission of 63% at 550 nm, comparable to ITO, but with advantages in terms of processing conditions and cost. The gold grid OLED has a lower turn‐on voltage (7.7 V versus 9.8 V) and achieves a luminance of 100 cdm⁻² at a lower voltage (10.9 V versus 12.4 V) than the reference ITO OLED. We discuss the lower turn‐on voltage and the uniformity of the light output through the gold grid TCE and examine the conduction mechanisms in the ITO and gold grid TCE OLEDs.     

Light outcoupling efficiency enhancement in organic light emitting diodes using an organic scattering layer

Crystallized 4,7‐diphyenyl‐1,10‐phenanthroline (BPhen) films deposited by convenient vacuum thermal evaporation technique have been found to be an efficient means to extract the substrate wave guided light in organic light emitting diodes (OLEDs). The optimized BPhen film working as organic scattering layer was successfully used with OLEDs for light outcoupling efficiency improvement. Enhancement of 26%, 15% and 6% in efficiency of the blue, green and red OLEDs were obtained, respectively. The achievement was found to be advantageous in terms of simplicity of fabrication method and feasibility for large area OLED applications. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

3,4,9,10-Perylenetetracarboxylicdiimide as an interlayer for ultraviolet organic light emitting diodes

Ultraviolet organic light emitting diodes with 3,4,9,10-perylenetetracarboxylicdiimide (PTCDI) interlayer have been achieved. The emission spectrum and intensity were strongly dependent on the thickness of PTCDI interlayer, in spite of the fact that PTCDI has neither much lower HOMO nor much higher LUMO level, which is considered necessary for efficient charge blocking layers. The influence of PTCDI layer was investigated in three different device configurations and obtained results are discussed. For optimal device configuration, OLED with emission centered at 370 nm and turn-on voltage of 4.5 V is obtained.     

High-efficiency silicon light emitting diodes

Silicon has been regarded as a notoriously poor emitter of light fundamentally due to its indirect bandgap. However, as an elemental rather than a compound semiconductor, it has the advantage of fewer background defects as well as well-developed approaches to interface passivation. By minimising parasitic optical absorption and non-radiative bulk and surface recombination, and by enhancing the effective optical photon generation volume, respectable silicon light emission efficiencies are demonstrated. These are within the range of direct gap III–V semiconductors and higher than any at low powered densities. Possible applications are also discussed.     

Organic light emitting diodes using magnesium doped organic acceptor as electron injection layer and silver as cathode

Organic light emitting diodes employing magnesium doped electron acceptor 3, 4, 9, 10 perylenetetracarboxylic dianhydride (Mg:PTCDA) as electron injection layer and silver as cathode were demonstrated. As compared to Mg:Ag cathode, the combination of the Mg:PTCDA layer and silver provided enhanced electron injection into tris (8-quinolinolato) aluminium. The device with 1:2 Mg:PTCDA and Ag showed an increase of about 12% in the maximum current efficiency, mainly due to the improved hole-electron balance, and an increase of about 28% in the maximum power efficiency, as compared to the control device using Mg:Ag cathode. The properties of Mg:PTCDA composites were studied as well.     

Direct observation of the potential distribution within organic light emitting diodes under operation

We show the first direct measurement of the potential distribution within organic light emitting diodes (OLEDs) under operation and hereby confirm existing hypotheses about charge transport and accumulation in the layer stack. Using a focused ion beam to mill holes in the diodes we gain access to the cross section of the devices and explore the spatially resolved potential distribution in situ by scanning Kelvin probe microscopy under different bias conditions. In bilayer OLEDs consisting of tris(hydroxyquinolinato) aluminum (Alq₃)/N, N ′‐bis(naphthalene‐1‐yl)‐N,N ′‐bis(phenyl) benzidine (NPB) the potential exclusively drops across the Alq₃ layer for applied bias between onset voltage and a given transition voltage. These findings are consistent with previously performed capacitance–voltage measurements. The behavior can be attributed to charge accumulation at the interface between the different organic materials. Furthermore, we show the potential distribution of devices with different cathode structures and degraded devices to identify the cathode interface as main culprit for decreased performance. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Auger carrier leakage in III‐nitride quantum‐well light emitting diodes

Auger induced leakage is shown to be a contributing factor for the internal quantum efficiency (IQE) droop in III‐nitride quantum‐well light emitting diodes (LEDs). The mechanism is based on leakage current from carrier spill‐out of the well originating from energy transfer during Auger recombination. Adding this leakage reduces the Auger coefficient by 50% when compared to a standard Auger model with cubic density dependence. As reference, experimental data of a green quantum‐well LED are taken. Direct leakage due to non‐ideal carrier capture and re‐emission out of the well affects the IQE at current densities much larger than the maximum IQE point. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Improved light extraction of organic light emitting diodes with a nanopillar pattering structure

We have investigated the properties of organic light emitting diodes(OLEDs)with a nanopillar patterning structure at organic–metal or organic–organic interfaces.The results demonstrate that the introduction of a nanopillar structure can improve the light extraction efficiency greatly.We also find that the number,height,and position of nanopillars all affect the light extraction of OLEDs.The maximum power efficiency of a device with an optimized nanopillar patterning mode can be improved to 2.47 times that of the reference device.This enhancement in light extraction originates from the improved injected carriers,the broadened charge recombination zone,and the intensified wave guiding effects.     

修饰阴极界面提高聚合物白光二极管发光效率

利用聚合物的不同溶解性,研究用旋涂方法制备双层高分子白光二极管(WPLED),采用器件结构为：ITO/PEDOT(50nm)/PVK:PFO-BT: PFO-DBT(40nm)/PFO(40nm)/Ba(4nm) /Al(120nm),当相对比例为PVK: PFO-BT:PFO-DBT=1∶4%：3%时,得到标准白光,最大电流效率为2.4 cd/A,最大亮度为3215 cd/m²,色坐标为(0.33,0.34).用水溶性的聚电介质层修饰阴极界面,器件效率可以进一步提高到5.28 cd 关键词： 聚合物发光二极管 白光 双发光层结构     

Spectral dependence of light extraction efficiency of high‐power III‐nitride light‐emitting diodes

Using the recently suggested method of processing the data on external quantum efficiency as a function of output optical power, we have estimated the dependence of light extraction efficiency of high‐power light‐emitting diodes (LEDs) on their emission wavelength varied between 425 nm and 540 nm. The extraction efficiency is found to increase with the wavelength from ～80% to ～85% in this spectral range and to correlate with the wavelength dependence of reflectivity of the large‐area p‐electrode being the essential unit of the LED chip design. The correlation found identifies the incomplete reflection of emitted light from the electrode as the major mechanism eventually controlling the spectral dependence of the efficiency of light extraction from the LEDs.

     

ITO/有机半导体/金属结构OLED器件的数值模拟

基于稳态的小信号漂移扩散方程,建立了有电极的单层有机电致发光(OLED)器件的数值模型,编制的MATLAB程序,首先模拟了文献中的OLED器件电极附近正电荷层(面电荷)对器件J-V的影响,得到了和文献中一致的结果. 模拟了ITO/PPV/Ca结构的OLED器件,模拟时,考虑了OLED阳极附近存在正体电荷,得到的J-V曲线和文献中的实验结果一致,体电荷产生了势垒,影响了电流曲线. 关键词： 有机电致发光 数值模拟 漂移扩散模型     

Degradation behaviors of high power GaN-based blue light emitting diodes

The degradation mechanism of high power InGaN/GaN blue light emitting diodes(LEDs)is investigated in this paper.The LED samples were stressed at room temperature under 350-mA injection current for about 400 h.The light output power of the LEDs decreased by 35%during the first 100 h and then remained almost unchanged,and the reverse current at 5 V increased from 10 9A to 10 7A during the aging process.The power law,whose meaning was re-illustrated by the improved rate equation,was used to analyze the light output power-injection current(L–I)curves.The analysis results indicate that nonradiative recombination,Auger recombination,and the third-order term of carriers overflow increase during the aging process,all of which may be important reasons for the degradation of LEDs.Besides,simulating L–I curves with the improved rate equation reveal that higher-than-third-order terms of carriers overflow may not be the main degradation mechanism,because they change slightly when the LED is stressed.     

Simplified hybrid white organic light‐emitting diodes with efficiency/efficiency roll‐off/color rendering index/color‐stability trade‐off

A high‐performance hybrid white organic light‐emitting diode (WOLED) based on a simple structure has been developed. The resulting device exhibits a maximum total current efficiency and power efficiency of 35.7 cd/A and 30.6 lm/W, respectively. Even at a high luminance of 1000 cd/m², a current efficiency of 32.0 cd/A and a power efficiency of 19.4 lm/W are obtained, suggesting that the device exhibits a low efficiency roll‐off. Besides, the device shows excellent color‐stability during a wide range of luminance and a high color rendering index (CRI) of 83 is obtained. Moreover, the origin of the superior properties is explored comprehensively. Such achieved results demonstrate that high efficiency, low efficiency roll‐off, stable color and high CRI can be simultaneously realized in a simplified hybrid WOLEDs. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Multi‐peak and chromaticity‐stable top‐emitting white organic light‐emitting diodes using single blue emitter

We have fabricated multi‐peak and chromaticity‐stable top‐emitting white organic light‐emitting diodes (TEWOLEDs) using single blue emitter. Besides the intrinsic emission of blue emitter, the additional emission can be well realized by simply adjusting the thickness of hole transporting layer (HTL), thus modifying the optical cavity length to obtain different resonant wavelengths. The detailed variation process for multi‐peak spectra with the increase of HTL thickness is studied, which provides a guidance for the design of microcavity TEWOLEDs.

     

A facile method for flexible GaN‐based light‐emitting diodes

Flexible GaN‐based light‐emitting diodes (LEDs) on polyethylene terephthalate (PET) substrates are demonstrated. The process uses commercial LEDs on patterned sapphire substrates, laser lift‐off (LLO), wet etching for additional surface roughening, and mounting of the freestanding LED on a PET substrate. Electrical and optical properties from the free‐standing LLO‐LEDs mounted on the flexible PET substrates were characterized. The process is scalable to large wafer diameters. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

p型氮化镓的低温生长及发光二极管器件的研究

采用金属有机物化学气相淀积技术(MOCVD)在蓝宝石衬底上低温(870—980℃)生长p型氮化镓 (p-GaN).用Hall测试仪测量材料的电学性能，发现当温度低于900℃时，材料的电阻率较高 ；在900—980℃均可获得导电性能良好的p-GaN.另外，电导性能除与掺杂浓度有关，还与p- GaN生长条件有关，氮镓摩尔比过低导电性能就较差，过高则会引起表面粗糙.采用优化后的 p-GaN制作了绿光发光二极管器件，发现生长温度越低器件发光强度越高，反向电压也越高 ，但正向电压只是略有升高. 关键词： Ⅲ-Ⅴ族半导体 氮化镓 发光二极管 金属有机物化学气相淀积     

Electroluminescence enhancement in ultraviolet organic light‐emitting diode with graded hole‐injection and ‐transporting structure

Electroluminescent intensity and external quantum efficiency (EQE) in ultraviolet organic light‐emitting diodes (UV OLEDs) have been remarkably enhanced by using a graded hole‐injection and ‐transporting (HIT) structure of MoO₃/N,N ′‐bis(naphthalen‐1‐yl)‐N,N ′‐bis(phenyl)‐benzidine/MoO₃/4,4′‐bis(carbazol‐9‐yl)biphenyl (CBP). The graded‐HIT based UV OLED shows superior short‐wavelength emis‐ sion with spectral peak of ～410 nm, maximum electroluminescent intensity of 2.2 mW/cm² at 215 mA/cm² and an EQE of 0.72% at 5.5 mA/cm². Impedance spectroscopy is employed to clarify the enhanced hole‐injection and ‐transporting capacity of the graded‐HIT structure. Our results provide a simple and effective approach for constructing efficient UV OLEDs. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

基于相变原理模拟红色顶发射有机电致发光器件的出光性能

研究了有机发光器件(organic light emitting diodes, 简记为OLED)半透明电极上形成的反射相移对OLED光谱产生调制现象.以红色微腔结构顶发射OLED(top emitting OLED,TOLED)为例,基于微腔理论和传输矩阵理论建立物理模型,采用计算机数值模拟方法,得出结果表明器件发光光谱的调制作用不只局限于有机层厚度,也和反射相移有关.通过改变覆盖到顶电极表面的有机层厚度的简单方法,可以实现对顶电极反射相移的调节,从而改变TOLED光学性能.这一结果为进一步改善器件的性 关键词： 反射相移模拟 红色微腔 顶发射有机发光     

Organic light emitting devices

The purpose of this paper is to provide general information about basic physical processes involved in organic electroluminescence and to present the main parameters and advantages of organic light emitting devices (OLEDs).