Cross‐linked azobenzene liquid‐crystalline polymer films with a poly(oxyethylene) backbone are synthesized by photoinitiated cationic copolymerization. Azobenzene moieties in the film surface toward the light source are simultaneously photoaligned during photopolymerization with unpolarized 436 nm light and thus form a splayed alignment in the whole film. The prepared films show reversible photoinduced bending behavior with opposite bending directions when different surfaces of one film face to ultraviolet light irradiation.
Hierarchical semicrystalline block copolymer nanoparticles are produced in a segmented gas‐liquid microfluidic reactor with top‐down control of multiscale structural features, including nanoparticle morphologies, sizes, and internal crystallinities. Control of multiscale structure on disparate length scales by a single control variable (flow rate) enables tailoring of drug delivery nanoparticle function including release rates.
Here, the preparation of a novel block copolymer consisting of a statistical copolymer N‐(2‐hydroxypropyl) methacrylamide‐s‐N‐(3‐aminopropyl) methacrylamide and a short terminal 3‐guanidinopropyl methacrylamide block is reported. This polymer structure forms neutral but water‐soluble nanosized complexes with siRNA. The siRNA block copolymer complexes are first analyzed using agarose gel electrophoresis and their size is determined with fluorescence correlation spectroscopy. The protective properties of the polymer against RNA degradation are investigated by treating the siRNA block copolymer complexes with RNase V1. Heparin competition assays confirm the efficient release of the cargo in vitro. In addition, the utilization of microscale thermophoresis is demonstrated for the determination of the binding strength between a fluorescently labeled polyanion and a polymer molecule.
Deviating from the traditional formation of block copolymer derived isoporous membranes from one block copolymer chemistry, here asymmetric membranes with isoporous surface structure are derived from two chemically distinct block copolymers blended during standard membrane fabrication. As a first proof of principle, the fabrication of asymmetric membranes is reported, which are blended from two chemically distinct triblock terpolymers, poly(isoprene‐b‐styrene‐b‐(4‐vinyl)pyridine) (ISV) and poly(isoprene‐b‐styrene‐b‐(dimethylamino)ethyl methacrylate) (ISA), differing in the pH‐responsive hydrophilic segment. Using block copolymer self‐assembly and nonsolvent induced phase separation process, pure and blended membranes are prepared by varying weight ratios of ISV to ISA. Pure and blended membranes exhibit a thin, selective layer of pores above a macroporous substructure. Observed permeabilities at varying pH values of blended membranes depend on relative triblock terpolymer composition. These results open a new direction for membrane fabrication through the use of mixtures of chemically distinct block copolymers enabling the tailoring of membrane surface chemistries and functionalities.
The present review focuses on the recent progress made in thin film orientation of semi‐conducting polymers with particular emphasis on methods using epitaxy and shear forces. The main results reported in this review deal with regioregular poly(3‐alkylthiophene)s and poly(dialkylfluorenes). Correlations existing between processing conditions, macromolecular parameters and the resulting structures formed in thin films are underlined. It is shown that epitaxial orientation of semi‐conducting polymers can generate a large palette of semi‐crystalline and nanostructured morphologies by a subtle choice of the orienting substrates and growth conditions.
Two‐dimensional (2D) palladium nanocube array is achieved on plasma‐etched block copolymer templates, while the well‐aligned nanocubes remain active. Anisotropic nanocubes are site‐selectively assembled on various nanopatterns by capillary force. The nanocube array is proved to be easily tunable, and the dimensional commensurability plays a key role in the configurations of the nanocube assemblies. Not only catalytic nanocube array under confinement but also template for the growth of nanoscale zinc oxide (ZnO) nanorods is exemplified as the potential application of the nanoarray.
PEG400 (polyethylene glycol, MW 400) biscyanoacrylate is synthesized and copolymerized with 2‐octyl cyanoacrylate for potential use as bioadhesive. PEG400 biscyanoacrylate is synthesized from the esterification of anthracenyl cyanoacrylic acid where the anthracene unit serves as vinyl‐protecting group. Copolymerization increases the plasticity, mechanical strength, and resilience of the resulted polymer as determined by dynamic mechanical analysis. Peeling test confirms its superior bioadhesive properties. Surface morphology is characterized by SEM imaging. The formulations are cytocompatible and safe. This cyanoacrylate composition may provide improved bioadhesive cyanoacrylates.
Two soluble poly(phenyltriazolylcarboxylate)s (PPTCs) with high molecular weights (M w up to 26 800) are synthesized by the metal‐free 1,3‐dipolar polycycloadditions of 4,4′‐isopropylidenediphenyl diphenylpropiolate ( 1 ) and tetraphenylethene‐containing diazides ( 2 ) in dimethylformamide at 150 °C for 12 h in high yields (up to 93%). The resultant polymers are soluble in common organic solvents and are thermally stable with 5% weight loss temperatures higher than 375 °C. The PPTCs are nonemissive in solutions, but become highly luminescent upon aggregation, showing a phenomenon of aggregation‐induced emission. Their aggregates can be used as fluorescent chemosensors for high‐sensitivity detection of explosives.
A simple and effective airflow method to prepare sandwich‐type block copolymer films is reported. The films are composed of three layers: vertically oriented nanocylinders align in both upper and bottom layers and irregular nanocylinders exist in the bulk of the film. The vertically oriented nanocylinders in both sides can provide high accessibility to ions and ensures the exchange of chemical species between the membrane and external environment, while the irregularly oriented nanocylinders in the middle part of the film can prolong the pathway of ions transportation and enhance ions selectivity.
The preparation of multifunctional polymers and block copolymers by a straightforward one‐pot reaction process that combines enzymatic transacylation with light‐controlled polymerization is described. Functional methacrylate monomers are synthesized by enzymatic transacylation and used in situ for light‐controlled polymerization, leading to multifunctional methacrylate‐based polymers with well‐defined microstructure.
Janus particles with anisotropic biofunctionalities are perfect models to mimic anisotropic architectures and directional interactions that occur in nature. It is therefore highly desirable to develop reliable and efficient methods to synthesize biofunctional Janus particles. Herein, a facile method combining seeded‐emulsion polymerization and thiol‐click chemistry has been developed to synthesize Janus particles with glucose moieties on one side. These biofunctional Janus particles show region‐selective binding of protein, which represents a big step toward biomimicry, and demonstrates the potential of the bioJanus particles for targeted drug delivery and binding.
Reversible addition‐fragmentation chain transfer polymerization yields reactive block copolymers bearing the pentafluorophenyl ester (PFPA) group, and subsequent Click amidation using 2,2,6,6‐tetramethylpiperidine‐N‐oxyl‐ and imidazolium‐functionalized primary amines produces the corresponding functional block copolymers, leading to installation of statistical radical‐ and ionic sites into the PFPA segment. The monolayered thin film devices fabricated using the obtained block copolymers exhibit repeatable switching of electric conductivity (on/off ratio > 103) under a bias voltage, which reveals that the coexistence of radicals and ions in the same spherical domain of the copolymer layer is a prerequisite for repeatable switching memory.
Copolymers of N‐isopropylacrylamide (NIPAM) and dopamine methacrylate can establish a reversible, self‐healing 3D network in aprotic solvents based on hydrogen bonding. The reactivity and hydrogen bonding formation of catechol groups in copolymer chains are studied by UV–vis and 1H NMR spectroscopy, while reversibility from sol to gel and inverse as well as self‐healing properties are tested rheologically. The produced reversible organogel can self‐encapsulate physically interacting or chemically bonded solutes such as drugs due to thermosensitivity of the used copolymer. This system offers dual‐targeted and controlled drug delivery and release—by slowing down release kinetics by supramolecular bonding of the drug and by reducing diffusion rates due to modulus increase.
The synthesis of a series of dithienosilole–benzotriazole donor–acceptor statistical copolymers with various donor–acceptor ratios is reported, prepared by Kumada catalyst‐transfer polymerization. Statistical copolymer structure is verified by 1H NMR and optical absorption spectroscopy, and supported by density functional theory (DFT) calculations. The copolymers exhibit a single optical absorption band that lies between dithienosilole and benzotriazole homopolymers, which shifts with varying donor–acceptor content. A chain extension experiment using a partially consumed benzotriazole solution as a macroinitiator followed by addition of dithienosilole leads to the synthesis of a statistical dithienosilole–benzotriazole block copolymer from a pure benzotriazole block, demonstrating that both chain extension and simultaneous monomer incorporation are possible using this methodology.
Recently, polymer drug conjugates (PDCs) have attracted considerable attention in the treatment of cancer. In this work, a simple strategy has been developed to make PDCs of an antitumor alkylating agent, chlorambucil, using a biocompatible disulphide linker. Chlorambucil‐based chain transfer agent was used to prepare various homopolymers and block copolymers in a controlled fashion via reversible addition–fragmentation chain transfer polymerization. Chlorambucil conjugated block copolymer, poly(polyethylene glycol monomethyl ether methacrylate)‐b‐poly(methyl methacrylate), formed nanoaggregates in aqueous solutions, which are characterized by dynamic light scattering and field emission‐scanning electron microscopy. Finally, the simplicity of the design is exemplified by performing a release study of chlorambucil under reducing condition by using D,L‐dithiothreitol.
The phase behavior of block copolymer based supramolecular complexes polystyrene‐block‐poly(4‐vinylpyridine) (PS‐b‐P4VP) and amphiphilic pentadecylphenol (PDP) molecules resembles the phase behavior of conventional block copolymers. Several PS‐b‐P4VP(PDP) complexes are found to self‐assemble into gyroid nanostructures. Typically, the grains are randomly oriented with a maximal size of several micrometers. Here, the orientation of a gyroid PS‐b‐P4VP(PDP) complex upon shearing is reported. It is found that the (111) gyroid lattice direction orients parallel to the shear direction after only several seconds of large amplitude oscillatory shearing. Oriented gyroid complexes can be used as templates for the preparation of metal nanofoams with improved ordering with potentially superior properties.
Supramolecular polyfluorenol enable assembly into conjugated polymer nanoparticles (CPNs). Poly{9‐[4‐(octyloxy)phenyl]fluoren‐9‐ol‐2,7‐diyl} (PPFOH)‐based supramolecular nanoparticles are prepared via reprecipitation. PPFOH nanoparticles with diameters ranging from 40 to 200 nm are obtained by adding different amounts of water into DMF solution. Size‐dependent luminescence is observed in PPFOH‐based hydrogen‐bonded nanoparticles that is different from that of poly(9,9‐dioctylfluorenes). Finally, white light‐emitting devices using CPNs with a size of 80 nm exhibit white emission with the CIE coordinates (0.31, 0.34). Amphiphilic conjugated polymer nanoparticles are potential organic nano‐inks for the fabrication of organic devices in printed electronics.
This paper reports on the synthesis of well‐defined polyacrylamide‐based nanogels via reversible addition–fragmentation chain transfer (RAFT) dispersion polymerization, highlighting a templateless route for the efficient synthesis of nanogels based on water‐soluble polymers. RAFT dispersion polymerization of acrylamide in co‐nonsolvents of water–tert‐butanol mixtures by chain extension from poly(dimethylacrylamide) shows well‐controlled polymerization process, uniform nanogel size, and excellent colloidal stability. The versatility of this approach is further demonstrated by introducing a hydrophobic co‐monomer (butyl acrylate) without disturbing the dispersion polymerization process.
Pulsed‐laser polymerization combined with polymer analysis by NMR and size‐exclusion chromatography is used to study the radical copolymerization kinetics of isoprene (IP) with glycidyl methacrylate (GMA). The copolymer is characterized by a close‐to‐alternating microstructure, with the addition of IP leading to a significant decrease in the composition‐averaged propagation rate coefficient. A rigorous fitting strategy is developed to fit a mixed penultimate model to the data, with the selectivity of the IP, but not the GMA, macroradical dependent on the penultimate unit.
Improving thermal stability of TEMPO‐oxidized cellulose nanofibrils (TOCNs) is a major challenge for the development and preparation of new nanocomposites. However, thermal degradation of TOCNs occurs at 220 °C. The present study reports a simple way to improve thermal stability of TOCNs by the heat‐induced conversion of ionic bonds to amide bonds. Coupling amine‐terminated polyethylene glycol to the TOCNs is performed through ionic bond formation. Films are produced from the dispersions by the casting method. Infrared spectroscopy and thermogravimetric analysis confirm conversion of ionic bonds to amide bonds for the modified TOCN samples after heating. As a result, improvement of TOCNs' thermal stability by up to 90 °C is successfully achieved.
