Studies on curing effect of phosphite monomer by EB radiation in the air

A new type phosphite active monomer was synthesized. The resisting oxygen inhibition effect of this monomer and the effects of irradiation dose and concentration of phosphite active monomer on curing were studied. At the same time, curing results were analysed, through gel content and IR spectrum. The excellent resisting oxygen inhibition result of this phosphite active monomer was shown by experiments. EB radiation curing in the air was successfully carried out by the phosphite active monomer.     

Production and crosslinking of multi-layer tubes (PE & metal) by E-beam

Irradiation crosslinking of PE-tubes has been used for heating floors for about 25 years. Such tubes are also used today for drinking water supply. A further development has been the coating of such tubes with Ethylene-Vinyl-Alcohol-Copolymers (EVAL), in order to prevent oxygen diffusion into the water through the PE tube. For about 15 years composite tubes made of PE and aluminum have been available. These tubes are crosslinked with electron beams. The energy of the accelerated electrons must be adjusted for the particular tube configuration, so that the inner PE-layer will be crosslinked. This paper will concern itself with the manufacture and the crosslinking of composite tubes.     

Investigation of irradiation dose rate on curing characteristics of carbon fiber/polymer composites by low‐energy electron beam

During in situ low‐energy electron beam (E‐Beam) curing for carbon fiber‐reinforced polymer composite, prepregs undergoes 3 sequenced curing processes, namely E‐Beam‐induced curing, postray curing after irradiation, and thermally induced curing. In this study, the irradiation dose rate (IDR) is demonstrated to be influential on the redistribution of the curing portions in the 3 curing stages and directly influences the interlaminar bonding quality of the stepwise cured laminates. Differential scanning calorimetry results showed that higher IDR resulted in higher temperature of irradiated prepregs, and hence, a higher degree of curing was induced by the E‐Beam within a dose range of 0 to 500 kGy as compared to lower IDRs, which decreased the interlaminar physical adhesive quality between layers. Analysis indicates that other than pure physical adhesion between uncured layers, postray curing can further enhance the interlaminar shear strength for cured laminates by introducing cross‐layer chemical bonding in the interlaminar zone.     

“Click” synthesis of thermally stable au nanoparticles with highly grafted polymer shell and control of their behavior in polymer matrix

Thermally stable core–shell gold nanoparticles (Au NPs) with highly grafted polymer shells were synthesized by combining reversible addition‐fragmentation transfer (RAFT) polymerization and click chemistry of copper‐catalyzed azide‐alkyne cycloaddition (CuAAC). First, alkyne‐terminated poly(4‐benzylchloride‐b‐styrene) (alkyne‐PSCl‐b‐PS) was prepared from the alkyne‐terminated RAFT agent. Then, an alkyne‐PSCl‐b‐PS chain was coupled to azide‐functionalized Au NPs via the CuAAC reaction. Careful characterization using FT‐IR, UV–Vis, and TGA showed that PSCl‐b‐PS chains were successfully grafted onto the Au NP surface with high grafting density. Finally, azide groups were introduced to PSCl‐b‐PS chains on the Au NP surface to produce thermally stable Au NPs with crosslinkable polymer shell ( Au‐PSN₃‐b‐PS 1 ). As the control sample, PS‐b‐PSN₃‐coated Au NPs ( Au‐PSN₃‐b‐PS 2 ) were made by the conventional “grafting to” approach. The grafting density of polymer chains on Au‐PSN₃‐b‐PS 1 was found to be much higher than that on Au‐PSN₃‐b‐PS 2 . To demonstrate the importance of having the highly packed polymer shell on the nanoparticles, Au‐PSN₃‐b‐PS 1 particles were added into the PS and PS‐b‐poly(2‐vinylpyridine) matrix, respectively. Consequently, it was found that Au‐PSN₃‐b‐PS 1 nanoparticles were well dispersed in the PS matrix and PS‐b‐P2VP matrix without any aggregation even after annealing at 220 °C for 2 days. Our simple and powerful approach could be easily extended to design other core–shell inorganic nanoparticles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Cellular Uptake of Gold Nanoparticles and Their Movement in 3D Multicellular Tumor Spheroids: Effect of Molecular Weight and Grafting Density of Poly(2‐hydroxyl ethyl acrylate)

It is known that the size of gold nanoparticles (GNPs) is not the only determining factor in the uptake by cells such as cancer cells. The surface functionalization plays a crucial role, in particular the nature of the ligand as well as the molecular weight and the grafting density. Here, poly(2‐hydroxy ethyl) acrylate (pHEA) with molecular weights ranging from 10, 20 to 39 g mol^?1 via reversible addition–fragmentation chain transfer polymerization is synthesized. These polymers are used directly to coat GNPs with sizes of 20, 40, and 70 nm as the trithiocarbonate functionality can strongly bind to the gold surface. The library of nine GNP is found to be nontoxic against lung carcinoma cells A549 and has negligible albumin protein absorption as determined by quartz crystal microbalance. Laser scanning confocal microscopy and flow cytometry reveal that GNP coated with medium length pHEA displays the highest cellular uptake while the effect of the size is not statistically significant. In contrast, multicellular tumor spheroids, which is a 3D model that simulates the tissue, enable the penetration of GNP coated with the longest pHEA chain while it also appears that smaller GNPs have now a clear advantage.     

Synthesis of π‐conjugated polymer containing both thiophene and phosphole sulfide in the main chain by simultaneous post‐element transformation of organotitanium polymer

The synthesis and unique optoelectronic features of a π‐conjugated polymer containing both thiophene and 1‐phenylphosphole sulfide units (multiple heteroles) in the main chain by the post‐element transformation of a regioregular organometallic polymer possessing titanacyclopentadiene‐2,5‐diyl unit are described. The π‐conjugated polymer containing multiple heteroles was obtained in 73% yield by the simultaneous reaction of the organotitanium polymer with sulfur monochloride and dichlorophenylphosphine (0.6 equiv each), whose number‐average molecular weight (M_n) and the molecular‐weight distribution (M_w/M_n) were estimated to be 11,000 and 3.4, respectively, by the size exclusion chromatography (SEC). The π‐conjugated polymer thus obtained was found to have the high HOMO and the low LUMO energy levels due to the electron‐rich thiophene and electron‐deficient phosphole sulfide units, respectively, as supported by its cyclic voltammetry (CV) analysis. Compared to a mixture of a polymer containing sole thiophene‐unit and that containing sole phosphole sulfide units, the π‐conjugated polymer‐containing multiple heteroles proved to exhibit interesting optical properties. For example, a specific emission peak was observed at 608 nm in the photoluminescence spectrum, which was not observed in the case of the thiophene‐containing polymer, the phosphole‐containing polymer, and their mixture. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2519–2525     

Synthesis of zwitterionic polymer by SET‐LRP at room temperature in aqueous

The Cu⁰‐mediated single electron transfer‐living radical polymerization of acrylamide and N,N‐dimethyl‐N‐methacryloyloxyethyl‐N‐sulfobutyl ammonium in aqueous at 25 °C using 2‐chloropropionamide as initiator with Cu⁰ powder/tris‐(2‐dimethylamino ethyl)amine (Me₆‐TREN) as catalyst system is studied. The results showed the characteristic of the “living” polymerization that were the M_n of polymers increased linearly with monomer conversion and the ln([M]₀/[M]) increased linearly with time too, meanwhile the narrow molecular of weight distributions were found at most cases. Because of the high rate constant of propagation and bimolecular termination of the acrylamide, the external addition of CuCl₂ is required to mediate deactivation the early stage of polymerization. In addition, the disproportionation constant of Cu^IX/L in H₂O is higher than in other solvents and the coordination of amino group and Cu^II takes place easily, so the isopropanol or N,N‐dimethylformamide is added to control the polymerization. High conversions were achieved within short time and the polymers prepared showed good antipolyelectrolyte properties in inorganic salts solutions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and crosslinking behavior of a novel linear polymer bearing 1,2,3‐triazol and benzoxazine groups in the main chain by a step‐growth click‐coupling reaction

The click‐coupling reaction was applied to polycondensation, to synthesize a high‐molecular weight prepolymer having benzoxazine moieties in the main chain. For the polycondensation, a bifunctional N‐propargyl benzoxazine was synthesized from bisphenol A, propargylamine, and formaldehyde. The propargyl group was efficiently used for the copper(I)‐catalyzed alkyne‐azide “click” reaction with p‐xylene‐α,α′‐diazide, to give the corresponding linear polycondensate having 1,2,3‐triazole junctions. The polycondensation proceeded in N,N‐dimethylformamide (DMF) at room temperature. By this highly efficient “click‐” polycondensation reaction, the benzoxazine ring in the monomer was successfully introduced into the polymer main chain without any side reaction. The obtained polymer (=prepolymer) underwent thermal crosslinking to afford the corresponding product, which was insoluble in a wide range of organic solvents and exhibited higher thermal stability than the polymer before crosslinking. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2316–2325, 2008     

Optimized domain size and enlarged D/A interface by tuning intermolecular interaction in all‐polymer ternary solar cells

The selection of sensitizer and its existence in the blend films are important to the performance of all‐polymer ternary solar cells. Herein, all‐polymer ternary solar cell devices, which used poly[4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′] dithiophene‐alt‐3‐fluorothieno[3,4‐b]thiophene‐2‐carboxy‐late] (PTB7‐Th) as donor, poly[[N,N‐bis(2‐octyldodecyl)‐napthalene‐1,4,5,8‐bis(dicarboximide)?2,6‐diyl]‐alt‐5, 5′‐(2,2′‐bithiophene)] (N2200) as acceptor and poly[N?900‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(40,70‐di‐2‐thienyl‐20,10,30‐benzothiadiazole) (PCDTBT) as sensitizer, are successfully demonstrated. The intermolecular interaction between donor PTB7‐Th and sensitizer PCDTBT may lead to aggregation of PTB7‐Th which decreases domain sizes and enlarges D/A effective interface area. In addition, the PCDTBT molecules also extend light absorption and cascaded energy levels of the ternary blend system. As a result, with 15% PCDTBT we get a power conversion efficiency of 5.11%, almost 20% higher than control device due to more favored exciton dissociation and higher charge transport efficiency. This study reveals a promising way to achieve high efficiency all‐polymer solar cells using a low‐band gap polymer PCDTBT. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1811–1819     

Gas sorption environments in poly(2,6‐dimethyl‐1,4‐phenylene oxide) by xenon‐129 nuclear magnetic resonance: Effects of processing

One‐ and two‐dimensional xenon‐129 nuclear magnetic resonance (¹²⁹Xe NMR) experiments were performed on a series of poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PXE) samples to characterize the sorption environments and the relative mobility of xenon in the samples. Samples of PXE in sealed NMR tubes pressurized with xenon were studied as a function of temperature, pressure, and processing. In a dense cast film of PXE, the shift relative to the free gas resonance is smaller than that observed for typical glassy polymers, indicating a higher free volume environment. Solubility rises rapidly as temperature decreases. The lower shift and rapid increase in solubility with decreasing temperature are consistent with a relatively high free volume environment for gas sorption. If PXE is antiplasticized, the shift is slightly larger, the increase in signal intensity with decreasing temperature is smaller, and the line widths are greater. This sample is a better packed glass with less free volume and slower diffusion. Samples of PXE produced by rapid precipitation have broad lines and even lower shifts corresponding to a wide distribution of higher free volume environments. The appearance of two lines at low temperatures is consistent with the presence of a bimodal distribution of environments similar to what has been observed with positron annihilation lifetime spectroscopy. The resonance closest to the free gas resonance is associated with very large free volume elements relative to those of traditional glassy polymers. In two‐dimensional experiments, there is a rapid exchange of xenon by diffusion between the two environments, indicating the close spatial proximity of the environments. Two‐dimensional experiments and one‐dimensional progressive saturation experiments reflect a rapid exchange of xenon between the sorbed state and the free gas resonance for the precipitated samples. At low temperatures, the high field peak exchanges more rapidly with the free gas. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1965–1974, 2002     

One‐step synthesis of polymer micro‐tubes tethered by polymer nanowire networks via RAFT polymerization of N,N′‐methylene bisacrylamide xerogel fibers in toluene and ethanol mixed solution

In the mixed solution of toluene and ethanol, polymer micro‐tubes (PMTs) tethered by polymer nanowire networks (PTPWNs) were fabricated facilely via one‐step reversible addition fragmentation chain transfer (RAFT) polymerization by taking N,N′‐methylene bisacrylamide (MBA) xerogel fibers as both template and monomer source. The products were analyzed by FTIR, SEM, TEM, surface area and porosity analyzer, and contact angle tester. The results indicated that PTPWNs were obtained as the sole product at ethanol content of 1.0 wt %. As the content of ethanol increases from 0 to 1.0 wt %, the specific surface area of the products became higher, indicating more polymer nanowire networks (PWNs) on the tubes. At ethanol contents of 1.5 wt % and 2.0 wt %, some particles were also obtained besides PTPWNs. The formation process of PTPWNs was studied by analyzing the products obtained at different reaction time. The results revealed that PTPWNs were formed by two steps, PMTs were formed quickly and then PWNs formed in the solution tethered to the tubes. Moreover, the effect of RAFT agent on the morphologies of the products revealed that PTPWNs could be obtained via RAFT polymerization at suitable dosage of RAFT agent, while polymer particles were generated via conventional free radical polymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1862–1868     

Ultratrace analysis of uracil and 5‐fluorouracil by molecularly imprinted polymer brushes grafted to silylated solid‐phase microextraction fiber in combination with complementary molecularly imprinted polymer‐based sensor

Main inborn errors of metabolism diagnosable through uracil (Ura) analysis and the therapeutic monitoring of toxic 5‐fluorouracil (5FU) in dihydro pyrimidine dehydrogenase (DPD) deficient patients require a sensitive, reproducible, selective and accurate method. In this work, an artificial receptor in the format of molecularly imprinted polymer (MIP) brush ‘grafted to’ the surface of sol–gel immobilized on cost‐effective homemade solid‐phase microextraction (SPME) fibers, individually imprinted with either of Ura and 5FU, was used in combination with a voltammetric sensor duly modified with the same MIP. This combination provided up to 10‐ and 8.4‐fold preconcentrations of Ura and 5FU, respectively, which was more than sufficient for achieving stringent detection limits in the primitive diagnosis of uracil disorders and fluoropyrimidine toxicity in DPD‐deficient patients. The proposed method permits the assessment of Ura and 5FU plasma concentrations with detection limits pf 0.0245 and 0.0484 ng mL^?1 (RSD = 1.0–2.5%, S/N = 3), respectively, without any problems of non‐specific false‐positives and cross‐reactivities in complicated matrices of biological samples. Copyright © 2008 John Wiley & Sons, Ltd.     

Stereo‐Inversion in the (4R)‐γ‐Decanolactone Synthesis by Saccharomyces cerevisiae: (2E,4S)‐4‐Hydroxydec‐2‐enoic Acid Acts as a Key Intermediate

Methyl (2E,4R)‐4‐hydroxydec‐2‐enoate, methyl (2E,4S)‐4‐hydroxydec‐2‐enoate, and ethyl (±)‐(2E)‐4‐hydroxy[4‐²H]dec‐2‐enoate were chemically synthesized and incubated in the yeast Saccharomyces cerevisiae. Initial C‐chain elongation of these substrates to C₁₂ and, to a lesser extent, C₁₄ fatty acids was observed, followed by γ‐decanolactone formation. Metabolic conversion of methyl (2E,4R)‐4‐hydroxydec‐2‐enoate and methyl (2E,4S)‐4‐hydroxydec‐2‐enoate both led to (4R)‐γ‐decanolactone with >99% ee and 80% ee, respectively. Biotransformation of ethyl (±)‐(2E)‐4‐hydroxy(4‐²H)dec‐2‐enoate yielded (4R)‐γ‐[²H]decanolactone with 61% of the ²H label maintained and in 90% ee indicating a stereoinversion pathway. Electron‐impact mass spectrometry analysis (Fig. 4) of 4‐hydroxydecanoic acid indicated a partial C(4)→C(2) ²H shift. The formation of erythro‐3,4‐dihydroxydecanoic acid and erythro‐3‐hydroxy‐γ‐decanolactone from methyl (2E,4S)‐4‐hydroxydec‐2‐enoate supports a net inversion to (4R)‐γ‐decanolactone via 4‐oxodecanoic acid. As postulated in a previous work, (2E,4S)‐4‐hydroxydec‐2‐enoic acid was shown to be a key intermediate during (4R)‐γ‐decanolactone formation via degradation of (3S,4S)‐dihydroxy fatty acids and precursors by Saccharomyces cerevisiae.     

Structural and Functional Changes of Reconstituted High-Density Lipoprotein (HDL) by Incorporation of α-synuclein: A Potent Antioxidant and Anti-Glycation Activity of α-synuclein and apoA-I in HDL at High Molar Ratio of α-synuclein

α-synuclein (α-syn) is a major culprit of Parkinson’s disease (PD), although lipoprotein metabolism is very important in the pathogenesis of PD. α-syn was expressed and purified using the pET30a expression vector from an E. coli expression system to elucidate the physiological effects of α-syn on lipoprotein metabolism. The human α-syn protein (140 amino acids) with His-tag (8 amino acids) was expressed and purified to at least 95% purity. Isoelectric focusing gel electrophoresis showed that the isoelectric point (pI) of α-syn and apoA-I were pI = 4.5 and pI = 6.4, respectively. The lipid-free α-syn showed almost no phospholipid-binding ability, while apoA-I showed rapid binding ability with a half-time (T_1/2) = 8 ± 0.7 min. The α-syn and apoA-I could be incorporated into the reconstituted HDL (rHDL, molar ratio 95:5:1:1, palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC):cholesterol:apoA-I:α-syn with the production of larger particles (92 Å) than apoA-I-rHDL (86 and 78 Å) and α-syn-rHDL (65 Å). An rHDL containing both apoA-I and α-syn showed lower α-helicity around 45% with a red shift of the Trp wavelength maximum fluorescence (WMF) from 339 nm, while apoA-I-HDL showed 76% α-helicity and 337 nm of WMF. The denaturation by urea addition showed that the incorporation of α-syn in rHDL caused a larger increase in the WMF than apoA-I-rHDL, suggesting that the destabilization of the secondary structure of apoA-I by the addition of α-syn. On the other hand, the addition of α-syn induced two-times higher resistance to rHDL glycation at apoA-I:α-syn molar ratios of 1:1 and 1:2. Interestingly, low α-syn in rHDL concentrations, molar ratio of 1:0.5 (apoA-I:α-syn), did not prevent glycation with more multimerization of apoA-I. In the lipid-free and lipid-bound state, α-syn showed more potent antioxidant activity than apoA-I against cupric ion-mediated LDL oxidation. On the other hand, microinjection of α-syn (final 2 μM) resulted in 10% less survival of zebrafish embryos than apoA-I. A subcutaneous injection of α-syn (final 34 μM) resulted in less tail fin regeneration than apoA-I. Interestingly, incorporation of α-syn at a low molar ratio (apoA-I:α-syn, 1:0.5) in rHDL resulted destabilization of the secondary structure and impairment of apoA-I functionality via more oxidation and glycation. However, at a higher molar ratio of α-syn in rHDL (apoA-I:α-syn = 1:1 or 1:2) exhibited potent antioxidant and anti-glycation activity without aggregation. In conclusion, there might be a critical concentration of α-syn and apoA-I in HDL-like complex to prevent the aggregation of apoA-I via structural and functional enhancement.     

A Novel 3D Framework Coordination Polymer based on Succinato bridged Helical Chains Connected by 4, 4' ‐ Bipyridine: [Cu(bpy)(H2O)2(C4H4O4)]?2H2O

Blue needle—shaped crystals of [Cu(bpy)(H₂O)₂(C₄H₄O₄)]· 2H₂O were obtained by slow evaporation of a methanolic aqueous solution containing a fresh Cu(C₄H₄O₄)· 2H₂O precipitate, 4, 4′—bipyridine, and ammonia. Within the complex, the six—coordinated Cu atoms are linked by bis—monodentate gauche succinate anions into chains propagating helically around the [001] axis. The chains are interconnected by 4, 4′—bipyridine ligands into a 3D framework with the crystal H₂O molecules located in the channels along the [100], [010] and [110] directions. The Cu²⁺ ions are in distorted octahedral coordination of two nitrogen and four oxygen atoms (equatorial bonds: Cu—N 1.986(5), 2.015(5)Å; Cu—O 1.950(6), 1.954(6)Å; axial bonds Cu—O: 2.524(9), 2.539(8)Å). Furthermore, the thermal and magnetic behavior of the compound will be discussed. Crystal data: hexagonal, P6₁ (no. 169), a = 11.066(2)Å, c = 24.965(5)Å, V = 2647.5(8)ų, Z = 6, R = 0.0528 and wR₂ = 0.1103 for 1426 observed reflections (F_o² > 2σ(F_o²)) out of 2170 unique reflections.