Compatibility and phase structure of binary blends of poly(lactic acid) and glycidyl methacrylate grafted poly(ethylene octane)

This work study is the compatibility, phase structure, and component interaction of poly(lactic acid) (PLA) and glycidyl methacrylate grafted poly(ethylene octane) (GMA-g-POE denoted as mPOE) blend by Fourier transform infrared (FTIR) spectra, dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), and wide-angle X-ray diffraction (WAXD), respectively. All the binary blend compositions exhibit two distinct glass transition temperatures corresponding to the mPOE-rich and PLA-rich phases, respectively. Moreover, these two peaks approach each other with increasing mPOE content, indicating partial compatibility between the PLA and mPOE. Chemical reactions between the end carboxyl groups of the PLA and epoxy groups of the mPOE are considered as the driving force of the enhanced compatibility. They lead to an increase in viscosity of the blends and a decrease in the structural symmetry of PLA. This result brings about a decrease in the spherulite growth rate and the degree of crystallinity. Glass transition temperature (T_g) depression of mPOE is attributed to the negative pressure imposed on the dispersed rubber phase, resulting from differential contraction due to the thermal shrinkage mismatch upon cooling from the melt state. The negative pressure in the dispersed particles, in turn, would cause a dilational effect for the matrix ligament between the particles, and therefore increases the ductility and toughness of PLA.     

Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends

Poly(lactic acid) (PLA) and polypropylene (PP) blends of various proportions were prepared by melt-compounding. The miscibility, phase morphology, thermal behavior, and mechanical and rheological properties of the blends were investigated. The blends were immiscible systems with two typical morphologies, spherical droplet and co-continuous, and could be obtained at various compositions. Complex viscosity, storage modulus and loss modulus depend on the PP content. Thermal degradation of all blends led to two weight losses, for PLA and PP. The incorporation of PP improved the thermal stability of the blend. The effect of compatibilizer (ethylene-butyl acrylate-glycidyl methacrylate terpolymer, EBA-GMA) on the morphology and mechanical properties of 70/30 w/w PLA/PP blends was investigated. The tensile strength of these blends reached a maximum for 2.5 wt% EBA-GMA, and impact strength increased with increasing EBA-GMA content, suggesting that EBA-GMA is an effective compatibilizer for PLA/PP blends.     

Thermal and mechanical analysis of injection moulded poly(lactic acid) filled with poly(ethylene glycol) and talc

In our research, the effect of talc particle size was analysed on the thermal and mechanical properties of renewable resource-based, biodegradable polymer poly(lactic acid) (PLA). Various talc particles with an average particle size of 24, 1.9, and 0.7 μm were blend mixed with PLA in 10 and 20 mass% containing no or an additional 10 mass% of poly(ethylene glycol) (PEG) to increase molecular chain mobility. It was demonstrated that with decreasing talc particle size, its nucleation ability increased as well as all of the investigated mechanical properties of the compounds, however, in case of compounds containing PEG, this tendency was the opposite according to Charpy impact strength results. The talc with the best nucleating ability was selected and a full factorial design of experiment was made to optimise the talc and PEG content and to investigate their cross-effect in the 1-3-5-10-15 mass% additive content range. Finally, the effect of mould temperature and cooling time was analysed on the crystallinity and heat deflection temperature of the final injection-moulded parts.     

聚乳酸/聚苯乙烯共混物的热氧稳定性研究

通过溶液浇铸法制备了聚乳酸/聚苯乙烯共混物,以差热-热重分析研究了共混物的热氧稳定性,结果表明聚乳酸中引入聚苯乙烯,可以增强聚乳酸/聚苯乙烯共混物的热氧稳定性.采用红外光谱分析了共混物不同结构的分子链间相互作用,证实聚乳酸大分子链羰基的未共用电子对和聚苯乙烯大分子链侧基苯环的π电子形成了n-π键.     

Transparent and ductile poly(lactic acid)/poly(butyl acrylate) (PBA) blends: Structure and properties

Poly(butyl acrylate) was prepared by the free radical polymerization of butyl acrylate as an initiator in the presence of 2,2′-Azoisobu-tyronitrile (AIBN) and the average molecular weight, polydispersity and thermal stability were evaluated. PLA and PBA were melt blended using a Haake Rheometer, and the light transmission, thermal properties, dynamic rheological properties, mechanical properties, phase morphology of blends and toughening mechanism were investigated. Dynamic rheology, SEM and DSC results show that the PLA is partial miscible with PBA. The PBA component improved the crystallization ability of PLA and the crystallinity of PLA increased with content of PBA (<15 wt.%). With the increase of PBA, the tensile strength and modulus of the blend decreased slightly while the elongation at break and toughness were dramatically increased. With the addition of PBA, the failure mode changes from brittle fracture of neat PLA to ductile fracture of the blend. Rheological results revealed the complex viscosity and melt elasticity of the blends decreased with increasing content of PBA and phase segregation occurred at loading above 11 wt.% PBA. UV–vis light transmittance showed that PLA/PBA blends with a high transparency, and the transmittance decreased with the amount of PBA.     

Conformational changes of poly(ethylene oxide) in poly(ethylene oxide)/poly(methyl methacrylate) blends by supercritical carbon dioxide

The effects of supercritical carbon dioxide (SC CO₂) fluids on the morphology and/or conformation of poly(ethylene oxide) (PEO) in PEO/poly(methyl methacrylate) (PMMA) blends were investigated by means of differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and Fourier transform infrared (FTIR). According to DSC data for a given blend, the melting enthalpy and, therefore, degree of crystallinity of PEO were increased, whereas the melting temperature of PEO was decreased, with SC CO₂ treatment. The enhancement of PEO crystallization with SC CO₂ treatment, as demonstrated by DSC data, was supported by WAXD data. According to FTIR quantitative analyses, before SC CO₂ treatments, the conformation of PEO was transformed from helix to trans planar zigzag via blending with PMMA. This helix‐to‐trans transformation of PEO increased proportionally with increasing PMMA content, with around 0.7% helix‐to‐trans transformation per 1% PMMA incorporation into the blend. For a given blend upon SC CO₂ treatments, the conformation of PEO was transformed from trans to helix. This trans‐to‐helix transformation of PEO decreased with increasing PMMA contents in the blends because of the presence of interactions between the two polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2479–2489, 2004     

Crystallization behavior and mechanical properties of poly(lactic acid)/poly(ethylene oxide) blends nucleated by a self-assembly nucleator

Poly(lactic acid) (PLA)/poly(ethylene oxide) (PEO) blends nucleated by a self-assembly nucleating agent, N,N′,N″-tricyclohexyl-1,3,5-benzenetricarboxylamide (BTCA), were prepared by melt blending. The crystallization behavior and mechanical properties of the materials were investigated by differential scanning calorimetry, polarized optical microscopy, wide-angle X-ray diffraction, dynamic mechanical analyzer and tensile testing. It was found that PEO had a synergistic effect together with BTCA on promoting PLA crystallization, besides its toughening effect on the material. Moreover, BTCA revealed prominent reinforcement effect on both neat PLA and PLA/PEO blends in the glass transition region and above, indicating the improvement on the heat resistance of the materials.

     

Compatibility and thermal properties of poly(3‐hydroxybutyrate)/poly(glycidyl methacrylate) blends

Poly(3‐hydroxybutyrate) (PHB)/poly(glycidyl methacrylate) (PGMA) blends were prepared by a solution‐precipitation procedure. The compatibility and thermal decomposition behavior of the PHB/PGMA blends was studied with differential scanning calorimetry, thermogravimetric analysis, and differential thermal analysis (DTA). The blends were immiscible in the as‐blended state, but for the blends with PGMA contents of 50 wt % or more, the compatibility was dramatically changed after 1 min of annealing at 200 °C. In addition, PHB/PGMA blends showed higher thermal stability, as measured by maximum decomposition temperatures and residual weight during thermal degradation. This was probably due to crosslinking reactions of the epoxide groups in the PGMA component with the carboxyl chain ends of PHB fragments during the degradation process, and the occurrence of such reactions can be assigned to the exothermic peaks in the DTA thermograms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 351–358, 2002     

Effect of poly (lactic acid)‐graft‐glycidyl methacrylate as a compatibilizer on properties of poly (lactic acid)/banana fiber biocomposites

The main aim of this study was to synthesis of poly (lactic acid) (PLA)‐graft‐glycidyl methacrylate (GMA) as well as its influence on the properties of PLA/banana fiber biocomposites. PLA‐graft‐GMA graft copolymer (GC) was synthesized by melt blending PLA with GMA using benzoyl peroxide and dicumyl peroxide as initiators. Graft copolymerization was confirmed by FTIR and ¹H‐NMR spectroscopic studies. PLA/silane treated banana fiber (SiB) biocomposites with various GC concentrations were prepared by melt blending followed by injection molding techniques. The influence of GC content on the mechanical, thermal and moisture resistance properties of the composite was investigated. The addition of 15 wt% GC content in the biocomposite provided optimum tensile and flexural strength, which is attributed to the greater compatibility between fiber and PLA matrix. The thermal properties of biocomposites have been evaluated using thermogravimetric analysis which provided evidence of improved interfacial adhesion between SiB and PLA by the addition of GC. Additionally, GC enhanced the moisture absorption resistance of biocomposites. These results indicated that GC is indeed a good candidate as a compatibilizing agent to improve the compatibility in PLA/fiber biocomposites. Copyright © 2015 John Wiley & Sons, Ltd.     

The thermal analysis of polymer blends of poly(ethylene oxide)/poly(methyl methacrylate)

Thermal analysis of the PEO/PMMA system show for the blends with higher molecular weight PMMA two glass transition temperatures in the 75–80 w/w% PMMA range. Thermal treatment is accompanied by a shift of this composition range of two Tg to lower PMMA contents. On the other hand observed melting point depression in the 0–60 w/w% PMMA range indicate compatibility of the blend components. Small negative interaction parameters approaching zero with increasing PMMA content of the blend, support the possible incompatibility in the observed composition range of two Tg.

---

Zusammenfassung Die Thermoanalyse des Systemes PEO/PMMA ergab für Gemische mit PMMA höheren Molekülgewichtes zwei Glasumwandlungspunkte /Tg/ im Bereich 75–80 m/m% PMMA. Eine Wärmebehandlung ist vom Verschieben dieses Bereiches mit den zwei Tg in Richtung niedrigerem PMMA-Gehalt begleitet. Weiterhin zeigt die Schmelzpunktserniedrigung im Bereich 0–60 m/m% PMMA die Kompatibilität der Gemischkomponenten. Kleine negative, mit steigendem PMMA-Gehalt des Gemisches gegen Null haltende Wechselwirkungsparameter unterstreichen die Möglichkeit einer Inkompatibilität im beobachteten Bereich der zwei Tg.

---

120–230°. 2 3590 . . . 150°, . .

     

Morphology of micron-sized monodispersed poly(butyl methacrylate)/polystyrene composite particles produced by seeded dispersion polymerization

In order to develop the seeded dispersion polymerization technique for the production of micron-sized monodispersed core/shell composite polymer particles the effect of polymerization temperature on the core/shell morphology was examined. Micron-sized monodispersed composite particles were produced by seeded dispersion polymerizations of styrene with about 1.4-μm-sized monodispersed poly(n-butyl methacrylate) (Pn-BMA) and poly(i-butyl methacrylate) (Pi-BMA) particles in a methanol/water (4/1, w/w) medium in the temperature range from 20 to 90 °C. The composite particles, PBMA/polystyrene (PS) (2/1, w/w), consisting of a PBMA core and a PS shell were produced with 2,2′-azobis(4-methoxy-2,4-dimethyl valeronitrile) initiator at 30 °C for Pn-BMA seed and with 2,2′-azobis(isobutyronitrile) initiator at 60 °C for Pi-BMA seed. The polymerization temperatures were a little above the glass-transition temperatures (T _g) of both Pn-BMA (20 °C) and Pi-BMA (40 °C). On the other hand, when the seeded dispersion polymerizations were carried out at much higher temperatures than the T _g of the seed polymers, composite particles having a polymeric oil-in-oil structure were produced. Received: 14 October 1998 Accepted in revised form: 2 June 1999     

Observations of crystallization and melting in poly(ethylene oxide)/poly(methyl methacrylate) blends by hot-stage atomic-force microscopy

The binary blend of poly(ethylene oxide)/atactic poly(methyl methacrylate) is examined using hot-stage atomic-force microscopy (AFM) in conjunction with differential scanning calorimetry and optical microscopy. It was found possible to follow in real time the melting process, which reveals itself to be nonuniform. This effect is ascribed to the presence of lamellae having different thicknesses. The crystallization process of poly(ethylene oxide) from the miscible melt is also followed in real time by AFM, affording detailed images of the impingement of adjacent spherulites and direct observation of lamellar growth and subsequent polymer solidification in the interlamellar space.© 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2643–2651, 1998     

Structure and blood compatibility of highly oriented poly(lactic acid)/thermoplastic polyurethane blends produced by solid hot stretching

Highly oriented poly(lactic acid) (PLA)/thermoplastic polyurethane (TPU) blends were fabricated through solid hot stretching technology in an effort to improve the mechanical properties and blood biocompatibility of PLA as blood‐contacting medical devices. It was found that the tensile strength and modulus of the blends can be improved dramatically by stretching. With the increase of draw ratio, the cold crystallization peak became smaller, and the glass transition and the melting peak moved to high temperature, while the crystallinity increased, and the grain size of PLA decreased, indicating of the stress‐induced crystallization during drawing. The oriented blends exhibited structures with longitudinal striations which indicate the presence of micro‐fibers. TPU phase was finely and homogeneously dispersed in the PLA, and after drawing, TPU domains were elongated to ellipsoid. The introduction of TPU and orientation could enhance the blood compatibility of PLA by prolonging kinetic clotting time, and decreasing hemolysis ratio and platelet activation. Copyright © 2013 John Wiley & Sons, Ltd.     

Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Crystallization and melting behavior of poly(ethylene oxide)/poly(n-butyl methacrylate) blends

The phase diagram, crystallization and melting behavior of poly(ethylene oxide) (PEO)/poly(n-butyl methacrylate) (PnBMA) blends have been investigated using differential scanning calorimetry and optical microscopy. The results show that the blends are miscible up to 85 °C and show an lower critical solution temperature-type demixing at a higher temperature. The isothermal crystallization studies of the blends indicate a reduction in the overall rate of crystallization. Analysis of isothermal crystallization data by means of Avrami equation leads to average values of the Avrami index of 2.5 for pure PEO and 3.0 for the different blend compositions. The melting behavior of the blends reveals double endotherms, which is ascribed to both secondary crystallization and recrystallization. The melting point depression study yielded χ₁₂=0, indicating a relatively low interaction strength.     

Compatible and tearing properties of poly(lactic acid)/poly(ethylene glutaric‐co‐terephthalate) copolyester blends

Fourier transform infrared and nuclear magnetic resonance results suggest that the carboxylic acid groups of poly(lactic acid) (PLA) molecules react with the hydroxyl groups of FePol (FP) molecules during the melt‐blending of PLA_xFP_y specimens. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) experiments of PLA and PLA/FP specimens suggest that only small amounts of poor PLA and/or FP crystals are present in their corresponding melt crystallized specimens. In fact, the percentage crystallinity, peak melting temperature, and onset re‐crystallization temperature values of PLA/FP specimens reduce gradually as their FP contents increase. However, the glass transition temperatures of PLA molecules found by DSC and DMA reduce to a minimum value as the FP contents of PLA_xFP_y specimens reach 6 wt %. Further DMA and morphological analysis of PLA/FP specimens reveal that FP molecules are compatible with PLA molecules at FP contents equal to or less than 6 wt %, as no distinguished phase‐separated FP droplets and tan δ transitions were found on fracture surfaces and tan δ curves of PLA/FP specimens, respectively. In contrast to PLA, the FP specimen exhibits highly deformable and tearing properties. After blending proper amounts of FP in PLA, the inherent brittle deformation and poor tearing behavior of PLA were successfully improved. Possible reasons accounting for these interesting crystallization, compatible and tearing properties of PLA/FP specimens are proposed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 913–920, 2010     

Hydrogen bonding assists stereocomplexation in poly(l‐lactic acid)/poly(d‐lactic acid) racemic blends

In this communication, we reported the sequence variation of stereocomplex crystals (SC) and homocrystals (HC) in poly(l ‐lactic acid)/poly(d ‐lactic acid) (PLLA/PDLA) racemic blends melts. It was evidenced that the emerging sequence of the SC and HC depends on the hydrogen bond formation in the melt, and the hydrogen bond is required for the stereocomplexation in PLLA/PDLA racemic blend. First, by combining a commercial fast‐scan chip‐calorimeter (Flash DSC 1) and micro‐FTIR, we found that hydrogen bonds were formed in the melt during cooling at 2.5 K/s, but not at 3000 K/s. Second, annealing the melt without hydrogen bonds at 100 °C led to HC emerging first, while annealing the melt with hydrogen bonds resulted in SC emerging at first. Third, the crystallization kinetics of the racemic blends after cooling to predefined T_c at 2.5 or 3000 K/s further verified that the hydrogen bonding can be inhibited effectively by cooling the racemic blends isotropic melt at fast enough rate. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 83–88     

Polypropylene/poly(butyl methacrylate) blends prepared by diffusion and subsequent polymerization of butyl methacrylate in isotactic polypropylene pellets

Polypropylene/poly(butyl methacrylate)(PP/PBMA) blends were prepared by diffusion and subsequent polymerization of butyl methacrylate(BMA) in commercial isotactic polypropylene(iPP) pellets.The diffusion kinetics,diametrical distribution of PBMA in a pellet and phase morphology of a typical PP/PBMA blend were investigated.