AlGaN/GaN肖特基结参数分析与电流运输机理研究

通过对AlGaN/GaN HEMT器件肖特基栅电流输运机理的研究,在变温下采用I-V法对AlGaN/GaN上的Ni/Au肖特基势垒高度和理想因子进行了计算. 通过对不同电流机理的分立研究,得到了更为准确的势垒高度值_b. 通过分析温度在300—550K之间肖特基反向泄漏电流的特性,得出结论：AlGaN材料的表面漏电不是HEMT器件反向泄漏电流的主要来源. 关键词： AlGaN/GaN异质结 肖特基结 理想因子     

极化效应对AlGaN/GaN异质结p-i-n光探测器的影响

基于等效薄层电荷近似模拟表征极化电荷的作用, 通过自洽求解Poisson-Schrödinger方程以及求解载流子连续性方程, 计算并且讨论了p-AlGaN层掺杂浓度和界面极化电荷对AlGaN/GaN异质结p-i-n紫外探测器能带结构和电场分布以及光电响应的影响. 结果表明, 极化效应与p-AlGaN层掺杂浓度相互作用对探测器性能有较大影响. 其中, 在完全极化条件下, p-AlGaN层掺杂浓度越大, p-AlGaN层的耗尽区越窄, i-GaN层越容易被耗尽, 器件光电流越小. 在一定掺杂浓度条件下, 极化效应越强, p-AlGaN层的耗尽区越宽, 器件的光电流越大. 最后还分析了该结构在不同温度下的探测性能, 证明了该结构可以在高温下正常工作.     

背势垒层结构对AlGaN/GaN双异质结载流子分布特性的影响

首先通过一维自洽求解薛定谔/泊松方程,研究了AlGaN/GaN双异质结构中AlGaN背势垒层Al组分和厚度对载流子分布特性的影响.其次利用低压MOCVD方法在蓝宝石衬底上生长出具有不同背势垒层的AlGaN/GaN双异质结构材料,通过汞探针CV测试验证了理论计算的正确性.理论计算和实验结果均表明,随着背势垒层Al组分的提高和厚度的增加,主沟道中的二维电子气面密度逐渐减小,寄生沟道的二维电子气密度逐渐增加;背势垒层Al组分的提高和厚度的增加能有效的增强主沟道的二维电子气限域性,但是却带来了较高的 关键词： AlGaN/GaN 双异质结构 限域性 寄生沟道     

AlGaN插入层对InAlN/AlGaN/GaN异质结散射机制的影响

InAlN/AlN/GaN异质结中,名义上的AlN插入层实为Ga含量很高的AlGaN层, Al, Ga摩尔百分比决定了电子波函数与隧穿几率,因此影响与InAlN/AlGaN势垒层有关的散射机制.本文通过求解薛定谔-泊松方程与输运方程,研究了AlGaN层Al摩尔百分含量对InAlN组分不均匀导致的子带能级波动散射、导带波动散射以及合金无序散射三种散射机制的影响.结果显示:当Al含量由0增大到1,子带能级波动散射强度与合金无序散射强度先增大后减小,导带波动散射强度单调减小;在Al含量为0.1附近的小组分范围内,合金无序散射是限制迁移率的主要散射机制,该组分范围之外,子带能级波动散射是限制迁移率的主要散射机制;当Al摩尔百分含量超过0.52,三种散射机制共同限制的迁移率超过无插入层结构的迁移率, AlGaN层显示出对迁移率的提升作用.     

GaN基异质结缓冲层漏电分析

通过对GaN基异质结材料C-V特性中耗尽电容的比较,得出AlGaN/GaN异质结缓冲层漏电与成核层的关系.实验结果表明,基于蓝宝石衬底低温GaN成核层和SiC衬底高温AlN成核层的异质结材料比基于蓝宝石衬底低温AlN成核层异质结材料漏电小、背景载流子浓度低.深入分析发现,基于薄成核层的异质结材料在近衬底的GaN缓冲层中具有高浓度的n型GaN导电层,而基于厚成核层的异质结材料的GaN缓冲层则呈高阻特性.GaN缓冲层中的n型导电层是导致器件漏电主要因素之一,适当提高成核层的质量和厚度可有效降低GaN缓冲层的背景载流子浓度,提高GaN缓冲层的高阻特性,抑制缓冲层漏电. 关键词： AlGaN/GaN异质结 GaN缓冲层 漏电 成核层     

N极性GaN/AlGaN异质结二维电子气模拟

通过自洽求解薛定谔方程和泊松方程,较系统地研究了GaN沟道层、AlGaN背势垒层、Si掺杂和AlN插入层对N极性GaN/AlGaN异质结中二维电子气(2DEG)的影响,分析表明,GaN沟道层厚度、AlGaN背势垒层厚度及Al组分变大都能一定程度上提高二维电子气面密度,AlGaN背势垒层的厚度和Al组分变大也可提高二维电子气限阈性,且不同的Si掺杂形式对二维电子气的影响也有差异,而AlN插入层在提高器件二维电子气面密度、限阈性等方面表现都较为突出,在模拟中GaN沟道层厚度小于5nm时无法形成二维电子气,超过20nm后二维电子气面密度趋于饱和,而AlGaN背势垒厚度超过40nm后二维电子气也有饱和趋势,对均匀掺杂和delta掺杂而言AlGaN背势垒层Si掺杂浓度超过5×10~(19)cm~(-3)后2DEG面密度开始饱和,而厚度为2nmAlN插入层的引入会使2DEG面密度从无AlN插入层时的0.93×10~(13)cm~(-2)提高到1.17×10~(13)cm~(-2)。     

Si调制掺杂AlGaN/GaN异质结磁阻拍频现象

在低温（15K—25K）和强磁场（0—10T）条件下，对二维电子气占据两个子带的Si调制掺杂AlGaN/GaN异质结构进行磁输运测量.在一定温度范围内观察到磁阻拍频现象.根据Sander等人和Raikh等人给出的磁阻振荡的具体表达式，拟合实验结果表明磁阻拍频是由第一子带S dH振荡和磁致子带间散射引起的磁阻振荡导致的. 关键词： AlGaN/GaN异质结构 SdH振荡 磁致子带间散射 磁阻拍频     

高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

AlGaN/GaN异质结Ni/Au肖特基表面处理及退火研究

采用O₂等离子体及HF溶液对AlGaN/GaN异质结材料进行表面处理后，Ni/Au肖特基接触特性比未处理有了明显改善，反向泄漏电流减小3个数量级.对制备的肖特基接触进行200—600℃ 5min的N₂气氛退火，发现退火冷却后肖特基反向泄漏电流随退火温度增大进一步减小.N₂气中600℃退火后肖特基二极管C-V特性曲线在不同频率下一致性变好，这表明退火中Ni向材料表面扩散减小了表面陷阱密度；C-V特性曲线随退火温度增大向右移动，从二维电子气耗尽电压绝对值减小反映了肖特基势垒的提高. 关键词： AlGaN/GaN 肖特基接触 表面处理 退火     

高击穿电压的AlGaN/GaN FP-HEMT研究与分析

就蓝宝石衬底上制备的AlGaN/GaN场板(field plate)HEMT器件、常规HEMT器件性能进行了分析对比.结果证明两种结构的器件直流参数变化不大，但是采用场板后器件的击穿电压从52V提高到了142V.在此基础上利用Sivaco软件对两种器件进行模拟仿真，深入分析了FP对器件击穿电压的影响.     

Effects of donor density and temperature on electron systems in AlGaN/AlN/GaN and AlGaN/GaN structures

It was reported by Shen et al that the two-dimensional electron gas (2DEG) in an AlGaN/AlN/GaN structure showed high density and improved mobility compared with an AlGaN/GaN structure, but the potential of the AlGaN/AlN/GaN structure needs further exploration. By the self-consistent solving of one-dimensional Schr\"{o}dinger--Poisson equations, theoretical investigation is carried out about the effects of donor density (0--1\times 10¹⁹cm^-3 and temperature (50--500K) on the electron systems in the AlGaN/AlN/GaN and AlGaN/GaN structures. It is found that in the former structure, since the effective \Delta E_c is larger, the efficiency with which the 2DEG absorbs the electrons originating from donor ionization is higher, the resistance to parallel conduction is stronger, and the deterioration of 2DEG mobility is slower as the donor density rises. When temperature rises, the three-dimensional properties of the whole electron system become prominent for both of the structures, but the stability of 2DEG is higher in the former structure, which is also ascribed to the larger effective \Delta E_c. The Capacitance--Voltage (C-V) carrier density profiles at different temperatures are measured for two Schottky diodes on the considered heterostructure samples separately, showing obviously different 2DEG densities. And the temperature-dependent tendency of the experimental curves agrees well with our calculations.     

Investigating gate metal induced reduction of surface donor density in GaN/AlGaN/GaN heterostructure by electroreflectance spectroscopy

The internal field of GaN/AlGaN/GaN heterostructure on Si-substrate was investigated by varying the thickness of an undoped-GaN capping layer using electroreflectance spectroscopy. The four samples investigated are AlGaN/GaN heterostructure without a GaN cap layer (reference sample) and three other samples with GaN/AlGaN/GaN heterostructures in which the different thickness of GaN cap layer (2.7 nm, 7.5 nm, and 12.4 nm) has been considered. The sheet carrier density (n_s) of a two-dimensional electron gas has decreased significantly from 4.66 × 10¹² cm⁻² to 2.15 × 10¹² cm⁻² upon deposition of a GaN capping layer (12.4 nm) over the reference structure. Through the analysis of internal fields in each GaN capping and AlGaN barrier layers, it has been concluded that the undiminished surface donor states (n_s) of a reference structure and the reduced n_s caused by the Au gate metal are approximately 5.66 × 10¹² cm⁻² and 1.08 × 10¹² cm⁻², respectively.     

纤锌矿AlGaN/AlN/GaN异质结构中光学声子散射影响的电子迁移率

对含有AlN插入层纤锌矿Al_xGa_1-xN/AlN/GaN异质结构,考虑有限厚势垒和导带弯曲的实际 异质结势,同时计入自发极化和压电极化效应产生的内建电场作用,采用数值自洽求解薛定谔方程和泊松方程, 获得二维电子气(2DEG)中电子的本征态和本征能级.依据介电连续模型和Loudon单轴晶体模型, 用转移矩阵法分析该体系中可能存在的光学声子模及三元混晶效应.进一步, 在室温下计及各种可能存在的光学声子散射,推广雷-丁平衡方程方法,讨论2DEG分布及二维电子迁移率的 尺寸效应和三元混晶效应.结果显示: AlN插入层厚度和Al_xGa_1-xN势垒层中Al组分的增加均会 增强GaN层中的内建电场强度,致使2DEG的分布更靠近异质结界面,使界面光学声子强于其他类型的 光学声子对电子的散射作用而成为影响电子迁移率的主导因素.适当调整AlN插入层的厚度和Al组分, 可获得较高的电子迁移率.     

Directly extracting both threshold voltage and series resistance from the conductance-voltage curve of an AlGaN/GaN Schottky diode

An Ni/Au Schottky contact on an AlGaN/GaN heterostructure has been prepared. By using the peak-conductance model, the threshold voltage and the series resistance of the AlGaN/GaN diode are simultaneously extracted from the conductance-voltage (G-V) curve and found to be in good agreement with the ones obtained by using the capacitance-voltage (C-V) curve integration and the plot of dV/d(ln I) versus current I. Thus, a method of directly and simultaneously extracting both the threshold voltage and the series resistance from the conductance-voltage curve for the AlGaN/GaN Schottky diode is developed.     

Determination of the relative permittivity of the AlGaN barrier layer in strained AlGaN/GaN heterostructures

Using the measured capacitance--voltage curves and the photocurrent spectrum obtained from the Ni Schottky contact on a strained Al_0.3Ga_0.7N/GaN heterostructure, the value of the relative permittivity of the AlGaN barrier layer was analysed and calculated by self-consistently solving Schr?dinger's and Poisson's equations. It is shown that the calculated values of the relative permittivity are different from those formerly reported, and reverse biasing the Ni Schottky contact has an influence on the value of the relative permittivity. As the reverse bias increases from 0 V to --3~V, the value of the relative permittivity decreases from 7.184 to 7.093.     

The effects of GaN capping layer thickness on two-dimensional electron mobility in GaN/AlGaN/GaN heterostructures

In this paper we present a study of the effect of GaN capping layer thickness on the two-dimensional (2D)-electron mobility and the two-dimensional electron gas (2DEG) sheet density which is formed near the AlGaN barrier/buffer GaN layer. This study is undertaken using a fully numerical calculation for GaN/Al_xGa_1−xN/GaN heterostructures with different Al mole fraction in the Al_xGa_1−xN barrier, and for various values of barrier layer thickness. The results of our analysis clearly indicate that increasing the GaN capping layer thickness leads to a decrease in the 2DEG density. Furthermore, it is found that the room-temperature 2D-electron mobility reaches a maximum value of approximately 1.8×10³ cm² /Vs⁻¹ for GaN capping layer thickness grater than 100 Å with an Al_0.32Ga_0.68N barrier layer of 200 Å thick. In contrast, for same structure, the 2DEG density decreases monotonically with GaN capping layer thickness, and eventually saturates at approximately 6×10¹² cm⁻² for capping layer thickness greater than 500 Å. A comparison between our calculated results with published experimental data is shown to be in good agreement for GaN capping layers up to 500 Å thickness.     

The effects of vicinal sapphire substrates on the properties of AlGaN/GaN heterostructures

AlGaN/GaN heterostructures on vicinal sapphire substrates and just-oriented sapphire substrates (0001) are grown by the metalorganic chemical vapor deposition method. Samples are studied by high-resolution x-ray diffraction, atomic force microscopy, capacitance--voltage measurement and the Van der Pauw Hall-effect technique. The investigation reveals that better crystal quality and surface morphology of the sample are obtained on the vicinal substrate. Furthermore, the electrical properties are also improved when the sample is grown on the vicinal substrate. This is due to the fact that the use of vicinal substrate can promote the step-flow mode of crystal growth, so many macro-steps are formed during crystal growth, which causes a reduction of threading dislocations in the crystal and an improvement in the electrical properties of the AlGaN/GaN heterostructure.