Investigation of metal–GaN and metal–AlGaN contacts by XPS depth profiles and by electrical measurements

Metal/GaN Schottky contacts have been studied by X-ray photoelectron spectroscopy (XPS). Au/GaN, Pt/GaN, Pd/GaN are sharp while Ti/GaN is diffuse with the following composition, starting from the surface: Ti+TiN, Ti+Ti_xGa_yN, Ti+Ti_xGa_yN+Ga, GaN+Ga. Au/AlGaN and Ni/AlGaN contacts are much broader than Au/GaN: Al and Ga are found more than 100 Å away from the interface. Schottky barrier height was measured for the Au/GaN, Pd/GaN, Pt/GaN, Au/AlGaN and Ni/AlGaN contacts.     

Influence of AlN nucleation layer growth conditions on quality of GaN layers deposited on (0 0 0 1) sapphire

The influence of AlN nucleation layer (NL) growth conditions on the quality of GaN layer deposited on (0 0 0 1) sapphire by organometallic chemical vapor phase epitaxy (OMVPE) has been investigated by X-ray diffraction, atomic force microscopy and transmission electron microscopy. Growth pressure, temperature and time were varied in this study. Results indicate that there exists an optimal thickness of the NL is required for optimal growth. Both thin and thick NLs are not conducive to the growth of high-quality GaN layers. Arguments have been developed to rationalize these observations.     

Electrical characterisation of AlGaN/GaN heterostructure wafers for high-power HFETs

Undoped 28 nm AlGaN on 1 μm GaN was grown by MOVPE for high power microwave HFETs. Non-destructive methods for rapid characterisation of the layers are described. Double contact mercury probe capacitance voltage measurements gave valuable information on AlGaN layer leakage, thickness and quality, but only gave an estimate of the carrier concentration and pinch-off voltage due to the absence of an ohmic contact to the 2DEG layer. A non-contact resistivity mapping system gave accurate average sheet resistance, but underestimated the cross-wafer variation.     

Influence of AlGaN/GaN/InGaN superlattice on the characteristics of LEDs grown by metalorganic chemical vapor deposition

This study examined the influence of strain-compensated triple AlGaN/GaN/InGaN superlattice structures (SLs) in n-GaN on the structural, electrical and optical characteristics of LEDs by analyzing the etch pits density (EPD), stress measurement, high-resolution X-ray diffraction (HRXRD), sheet resistance, photoluminescence (PL) and light–current–voltage (L–I–V). EPD, stress measurement and HRXRD studies showed that the insertion of AlGaN/GaN/InGaN SLs during the growth of n-GaN effectively distributed and compensated for the strong compressive stress, and decreased the dislocation density in n-GaN. The operating voltage at 20 mA for the LEDs grown with SLs decreased to 3.18 V from 3.4 V for the LEDs grown without SLs. In addition, a decrease in the spectral blue shift compared to the LEDs grown without SLs was observed in the LEDs grown with the SLs.     

Defect reduction in GaN epilayers and HFET structures grown on (0 0 0 1)sapphire by ammonia MBE

The quality of GaN epilayers grown by molecular beam epitaxy on substrates such as sapphire and silicon carbide has improved considerably over the past few years and in fact now produces AlGaN/GaN HEMT devices with characteristics among the best reported for any growth technique. However, only recently has the bulk defect density of MBE grown GaN achieved levels comparable to that obtained by MOVPE and with a comparable level of electrical performance. In this paper, we report the ammonia-MBE growth of GaN epilayers and HFET structures on (0 0 0 1)sapphire. The effect of growth temperature on the defect density of single GaN layers and the effect of an insulating carbon doped layer on the defect density of an overgrown channel layer in the HFET structures is reported. The quality of the epilayers has been studied using Hall effect and the defect density using TEM, SEM and wet etching. The growth of an insulating carbon-doped buffer layer followed by an undoped GaN channel layer results in a defect density in the channel layer of 2×10⁸ cm⁻². Mobilities close to 490 cm²/Vs at a carrier density of 8×10¹⁶ cm⁻³ for a 0.4 μm thick channel layer has been observed. Growth temperature is one of the most critical parameters for achieving this low defect density both in the bulk layers and the FET structures. Photo-chemical wet etching has been used to reveal the defect structure in these layers.     

Indium content determination related with structural and optical properties of InGaN layers

We studied the structural and optical properties of a set of nominally undoped epitaxial single layers of In_xGa_1−xN (0<x0.2) grown by MOCVD on top of GaN/Al₂O₃ substrates. A comparison of composition values obtained for thin (tens of nanometers) and thick (≈0.5 μm) layers by different analytical methods was performed. It is shown that the indium mole fraction determined by X-ray diffraction, measuring only one lattice parameter strongly depend on the assumptions made about strain, usually full relaxation or pseudomorphic growth. The results attained under such approximations are compared with the value of indium content derived from Rutherford backscattering spectrometry (RBS). It is shown that significant inaccuracies may arise when strain in In_xGa_1−xN/GaN heterostructures is not properly taken into account. Interpretation of these findings, together with the different criteria used to define the optical bandgap of In_xGa_1−xN layers, may explain the wide dispersion of bowing parameters found in the literature. Our results indicate a linear, E_g(x)=3.42−3.86x eV (x0.2), “anomalous” dependence of the optical bandgap at room temperature with In content for In_xGa_1−xN single layers.     

Magneto-photoluminescence of AlGaN/GaN quantum wells

The magneto-luminescence of GaN/AlGaN quantum wells in fields up to 52 T shows a field dependence that is strongly dependent on the well width. Strong redshifts are seen for the narrowest wells that are attributed to a Zeeman splitting. This is unexpected, since in bulk GaN epilayers the electron and hole g-factors of the lowest valence band cancel each other almost exactly. Therefore, we attribute this splitting to a reordering of the valence band due to the different band offsets caused by the strain and the aluminium component in the AlGaN barriers. The field dependence also gives information on the size of the exciton that has been converted into values for the exciton binding energy, and these values agree reasonably well with a theory that includes the presence of the electric field.     

Material optimisation for AlGaN/GaN HFET applications

An optimisation of some growth parameters for the epitaxy of AlGaN–GaN based heterostructure field effect transistors (HFET) at low pressure in a new 3 _* 2″ MOVPE reactor is presented. Some possible processes for the growth of semi-insulating buffers have been identified and are described. TEM analysis shows that the insulating character is not due to a high density of dislocations, whereas SIMS analysis shows that classical impurity (Si, O and C) concentrations are in the same range as in conductive undoped layers. Further studies are needed to identify the traps responsible for the compensation of the GaN layers. The properties of the two-dimensional electron gas (2DEG) located at the AlGaN–GaN interface can be tuned by modifying the characteristics of the AlGaN layer and of the insulating buffer. The best mobility (1500 cm² V⁻¹ s⁻¹ for n6×10¹² cm⁻²) is obtained when using a thick buffer layer, whereas the sheet carrier density is found to increase with the Al content in the undoped supply layer and reaches 1.1×10¹³ cm⁻² for a composition of 24%.     

Polarization induced 2D hole gas in GaN/AlGaN heterostructures

The generation of high density 2D hole gases is crucial for further progress in the electronic and optoelectronic nitride devices. In this paper, we present systematic theoretical studies of Mg-doped GaN/AlGaN gated heterostructures and superlattices. Our calculations are based on a self-consistent solution of the multiband k.p Schrödinger and Poisson equation and reveal that the hole 2D sheet density is mainly determined by the polarization induced interface charges. For an aluminium concentration of 30%, the induced hole density in the heterostructure can reach values up to 1.5×10¹³ cm⁻². In the GaN/AlGaN superlattices, the hole sheet density increases with the superlattice period and saturates for a period of 40 nm at a value of 1.5×10¹³ cm⁻².     

Impedance spectroscopy analysis of AlGaN/GaN HFET structures

For HFET application a series of samples with 30 nm Al_xGa_1−xN (x=0.02–0.4) layers deposited at 1040°C onto optimised 2 μm thick undoped GaN buffers were fabricated. The Al_xGa_1−xN/GaN heterostructures were grown on c-plane sapphire in an atmospheric pressure, single wafer, vertical flow MOVPE system. Electrical properties of the Al_xGa_1−xN/GaN heterostructures and thick undoped GaN layers were evaluated by impedance spectroscopy method performed in the range of 80 Hz–10 MHz with an HP 4192A impedance meter using a mercury probe. The carrier concentration distribution through the layer thickness and the sheet carrier concentration were evaluated. A non-destructive, characterisation technique for verification of device heterostucture quality from the measured C–V and G–V versus frequency characteristics of the heterostructure is proposed.     

AlGaN epitaxial lateral overgrowth on Ti-evaporated GaN/sapphire substrate

AlGaN growth using epitaxial lateral overgrowth (ELO) by metalorganic chemical vapor deposition on striped Ti, evaporated GaN on sapphire, has been investigated. AlGaN/AlN films growth on GaN/AlGaN superlattices (SLs) structure on the Ti masks, with various SLs growth temperature (1030, 1060 and 1090 °C) were grown. With increasing the growth temperature, AlGaN surface became flat. The AlGaN film had a cathodoluminescence peak around 345 nm. However, in secondary ion mass spectrometry (SIMS) measurement, Ti signal was detected on the top of AlGaN surface when GaN/AlGaN SLs was grown on Ti striped masks. By inserting the AlN blocking layer on SLs, Ti diffusion was stopped at the AlN layer, and the AlGaN crystalline quality was improved.     

The effect of the AlxGa1−xN/AIN buffer layer on the properties of GaN/Si(1 1 1) film grown by NH3-MBE

We describe the growth of GaN on Si(1 1 1) substrates with Al_xGa_1−xN/AlN buffer layer by ammonia gas source molecular beam epitaxy (NH₃-GSMBE). The influence of the AlN and Al_xGa_1−xN buffer layer thickness and the Al composition on the crack density of GaN has been investigated. It is found that the optimum thickness is 120 and 250 nm for AlN and Al_xGa_1−xN layers, respectively. The optimum Al composition is between 0.3<x<0.6.     

Optical properties of MOVPE-grown a-plane GaN and AlGaN

a-Plane GaN and AlGaN were grown on r-plane sapphire by low-pressure metal-organic vapor epitaxy (LP-MOVPE), and the effects of reactor pressure (from 40 to 500 Torr) and growth temperature (from 1020 to 1100 °C) on the crystalline quality and surface morphology of a-plane GaN were studied. The a-plane GaN grown under 40 Torr had a smooth-surface morphology but a poor crystalline quality; however, the a-plane GaN grown under 500 Torr had higher crystalline quality and optical properties, whose full-width at half-maximum of the X-ray rocking curve (XRC-FWHM) and intensity of yellow luminescence (YL) were smaller. Furthermore, the optical properties of a-plane GaN were investigated by photoluminescence (PL) in detail. We also studied the emission properties of a-plane Al_0.35Ga_0.65N grown at room temperature.     

Growth of Eu-doped GaN by gas source molecular beam epitaxy and its optical properties

Eu-doped GaN with various Eu concentrations were grown by gas source molecular beam epitaxy, and their structural and optical properties were investigated. With increasing Eu concentration from 0.1 to 2.2 at%, deterioration of the structural quality was observed by reflection high-energy electron diffraction, atomic force microscopy and X-ray diffraction. Such a deterioration may be caused by an enhancement of island growth and formation of dislocations. On the other hand, room temperature photoluminescence spectra showed red emission at 622 nm due to an intra-atomic f–f transition of Eu³⁺ ion and Fourier transform infrared spectra indicated an absorption peak at about 0.37 eV, which may be due to a deep defect level. The intensity of the red luminescence and the defect-related absorption peak increased with increasing Eu concentration, and a close correlation in the increasing behavior was observed between them. These results suggest that the deep defect level plays an important role in the radiative transition of Eu³⁺ ion in GaN and the optical process for the luminescence at 622 nm was discussed with relation to the defect.     

Lateral confined epitaxy of GaN layers on Si substrates

We developed a novel, simple procedure for achieving lateral confined epitaxy (LCE). This procedure enables the growth of uncracked GaN layers on a Si substrate, using a single, continuous metalorganic chemical vapor deposition (MOCVD) run. The epitaxial growth of GaN is confined to mesas, defined by etching into the Si substrate prior to the growth. The LCE-GaN layers exhibit improved morphological and optical properties compared to the plain GaN-on-Si layers grown in the same MOCVD system. By performing a set of LCE growth runs on mesas of varying lateral dimensions, we specified the crack-free range of GaN on Si as 14.0±0.3 μm.     

Synthesis of GaN nanospindles via a facile solid-state reaction route

Gallium nitride (GaN) nanospindles have been synthesized via a solid-state reaction at a low-temperature condition. X-ray powder diffraction (XRD), Raman spectrum and high-resolution transmission electron microscopy (HRTEM) revealed that the synthesized GaN crystallized in a hexagonal structure and displaying spindly particles morphology has an average diameter of 100 nm and length of 400 nm X-ray photoelectron spectroscopy (XPS) of the sample gave the atomic ratio of Ga and N of 1.04:1. Room-temperature photoluminescence (PL) spectrum showed that the as-prepared product had a peak emission at 372 nm. The possible formation mechanism of the wurtzite GaN is briefly discussed.     

Surface chemistry and transport effects in GaN hydride vapor phase epitaxy

A simple quasi-thermodynamic model of surface chemistry in GaN hydride vapor phase epitaxy (HVPE) is presented. The model is coupled with the detailed 3D simulations of species transport in a horizontal-tube reactor and validated by the comparison with the data on the GaN growth rate obtained by laser reflectometry. Parametric study of the growth rate as a function of temperature and species flow rates has been performed over a wide range of growth conditions. The important role of species transport in an HVPE reactor is demonstrated. In particular, a strong effect of the natural concentration convection resulting in the formation of recirculation zones and in a non-uniform vapor composition is revealed by modeling. The impact of these effects on the GaN growth rate and V/III ratio on the growth surface is discussed in detail.     

Growth of InAs on GaAs(1 0 0) by low-pressure metalorganic chemical vapor deposition employing in situ generated arsine radicals

InAs was grown by low-pressure metalorganic chemical vapor deposition on vicinal GaAs(1 0 0) substrates misoriented by 2° toward [0 0 1]. We observed InAs crystal growth, at substrate temperatures down to 300°C, employing in situ plasma-generated arsine radicals as the arsenic source. The in situ generated arsine was produced by placing solid arsenic downstream of a microwave driven hydrogen plasma. Trimethylindium (TMIn) feedstock carried by hydrogen gas was used as the indium source. The Arrhenius plot of InAs growth rate vs. reciprocal substrate temperature displayed an activation energy of 46.1 kcal/mol in the temperature range of 300–350°C. This measured activation energy value is very close to the energy necessary to remove the first methyl radical from the TMIn molecule, which has never been reported in prior InAs growth to the best of authors’ knowledge. The film growth mechanism is discussed. The crystallinity, infrared spectrum, electrical properties and impurity levels of grown InAs are also presented.     

MBE growth of cubic AlyGa1−yN/GaN heterostructures—structural, vibrational and optical properties

Cubic Al_yGa_1−yN/GaN heterostructures on GaAs(0 0 1) substrates were grown by radio-frequency plasma-assisted molecular beam epitaxy. High resolution X-ray diffraction, micro-Raman, spectroscopic ellipsometry, and cathodoluminescence measurements were used to characterize the structural, optical and vibrational properties of the Al_yGa_1−yN epilayers. The AlN mole fraction y of the alloy was varied between 0.07<y<0.20. X-ray diffraction reciprocal space maps demonstrate the good crystal quality of the cubic Al_yGa_1−yN films. The measured Raman shift of the phonon modes of the Al_yGa_1−yN alloy was in excellent agreement with theoretical calculations. Both SE and CL of the Al_yGa_1−yN epilayer showed a linear increase of the band gap with increasing Al-content.     

Epitaxial growth of ZnO thin films on Si substrates by PLD technique

Epitaxial ZnO thin films have been grown on Si(1 1 1) substrates at temperatures between 550 and 700 °C with an oxygen pressure of 60 Pa by pulsed laser deposition (PLD). A ZnO thin film deposited at 500 °C in no-oxygen ambient was used as a buffer layer for the ZnO growth. In situ reflection high-energy electron diffraction (RHEED) observations show that ZnO thin films directly deposited on Si are of a polycrystalline structure, and the crystallinity is deteriorated with an increase of substrate temperature as reflected by the evolution of RHEED patterns from the mixture of spots and rings to single rings. In contrast, the ZnO films grown on a homo-buffer layer exhibit aligned spotty patterns indicating an epitaxial growth. Among the ZnO thin films with a buffer layer, the film grown at 650 °C shows the best structural quality and the strongest ultraviolet (UV) emission with a full-width at half-maximum (FWHM) of 86 meV. It is found that the ZnO film with a buffer layer has better crystallinity than the film without the buffer layer at the same substrate temperature, while the film without the buffer layer shows a more intense UV emission. Possible reasons and preventive methods are suggested to obtain highly optical quality films.