Determination of ofloxacin enantiomers in sewage using two-step solid-phase extraction and liquid chromatography with fluorescence detection

A robust analytical method has been developed and validated for the trace analysis of ofloxacin enantiomers in sewage using two-step solid-phase extraction purification and liquid chromatography with fluorescence detection (LC-FL). Ofloxacin enantiomers were separated on an Aglient TC-C-18 column using MeOH-water containing 4mmol/L CuSO4 and 5mmol/L l-isoleucine as mobile phase. The ofloxacin enantiomers were first extracted by a weak cation-exchange resin (WCX) and eluted with acidified MeOH (0.5% formic acid), then further purified by mixed mode of anion-exchange resin (MAX), resulting in ofloxacin recoveries generally above 95%. The limit of quantification was 0.08microg/L for each enantiomer. No significant matrix effect was found during the analytical procedure and standard solution calibration curves could be used for quantification. Total concentrations of both enantiomers in real sewage samples based on LC-FL method were consistent with those obtained upon liquid chromatography using tandem mass spectrometry (LC-MS/MS) method.     

Determination of thiabendazole in orange juice and rind by liquid chromatography with fluorescence detection and confirmation by gas chromatography/mass spectrometry after extraction by matrix solid-phase dispersion

A method was developed for the determination of thiabendazole (TBZ) in orange juice and rind based on matrix solid-phase dispersion (MSPD). TBZ was extracted with ethyl acetate and the extract was subsequently cleaned up on a solid-phase extraction column. Fungicide residues were determined by liquid chromatography with fluorescence detection. Recoveries through the method ranged from 87 to 97% with relative standard deviations < or = 11%. The detection and quantitation limits were 0.15 and 0.50 microg/kg, respectively. The confirmation of TBZ residues in positive samples was performed by solid-phase microextraction followed by gas chromatography with mass spectrometric detection using selected ion monitoring. The developed method was applied to determine TBZ levels in commercial orange juices and in juice and rind of fresh oranges. The influence of storage and washing of fruits on TBZ residues was also studied.     

Determination of amoxicillin residues in animal tissues by solid-phase extraction and liquid chromatography with fluorescence detection

Trace levels of amoxicillin residues were determined in animal tissues by liquid chromatography (LC) with fluorescence detection. An improved solid-phase extraction (SPE) procedure requiring less flammable solvent (diethyl ether) was developed for sample preparation. Muscle samples of beef, pork, chicken, and tilapia were extracted with a phosphate buffer followed by the modified SPE procedure for cleanup and concentration prior to the LC-fluorescence analysis. Average recoveries of fortified amoxicillin at 5, 10, and 20 micrograms/kg ranged from 83.9 to 85.8% in beef, 86.1 to 88.1% in pork, 81.7 to 82.9% in chicken, and 92.5 to 95.4% in tilapia. Relative standard deviations were < 4%.     

Determination of several pesticides in water by solid-phase extraction, liquid chromatography and electrospray tandem mass spectrometry

The analysis of pesticides in water samples is a problem of primary concern for quality control laboratories due to the toxicity level of these compounds and their public health risk. In order to evaluate the impact of pesticides in the Lisbon drinking water supply system, following the requirements of the European Union Directive 98/83/EC, we developed and validated an analytical method based on the combination of solid-phase extraction with liquid chromatography and tandem mass spectrometry. In this work, several pesticides were studied: imidacloprid, dimethoate, cymoxanil, carbendazime, phosmet, carbofuran, isoproturon, diuron, methidathion, linuron, pyrimethanil, methiocarbe, tebuconazole and chlorpyrifos. Several parameters of the electrospray source were optimized in order to get the best formation conditions of the precursor ion for each pesticide, namely capillary and extractor voltage, cone voltage, cone gas flow rate and desolvation gas flow rate. After optimization of the collision cell energy of the triple quadrupole, two different precursor ion-product ion transitions were selected for each pesticide, one for quantification and one for qualification, and these ions were monitored under time-scheduled multiple reaction monitoring (MRM) conditions. The selection of specific fragment ions for each pesticide guarantees a high degree of selectivity as well as additional sensitivity to quantify trace levels of these pesticides in water samples. This method showed excellent linearity ranges for all pesticides, with correlation coefficients greater than 0.9989. Determination limits (between 0.0041 and 0.0480 microg/L), precision (RSD <9.18%), accuracy and recovery studies in several water samples using solid-phase extraction were also performed.     

Determination of beta-blockers and beta2-agonists in sewage by solid-phase extraction and liquid chromatography-tandem mass spectrometry

A method using solid-phase extraction (SPE) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been developed for the determination of 12 beta-blockers and beta(2)-agonists in wastewater samples. Extraction of the drugs was effected by an Oasis MCX cartridge with a strong cation resin adsorbent. Matrix coextractives were removed from the SPE cartridge by methanol prior to the elution of the drugs with a mixture of dichloromethane, 2-propranol, and ammonium hydroxide. The extract was analyzed by LC-MS/MS with electrospray ionization operating in the positive mode. Recovery of the 12 compounds was in most cases better than 85% at the fortification levels of 500 and 50 ng/L, with standard deviations between 3 and 7%. Based on a concentration factor of 250, the method detection limits ranged from 6 to 11 ng/L for the target compounds. No degradation of these drugs in spiked sewage effluent samples was observed over a storage period of 7 days at 4 degrees C in the dark. Many beta-blockers were detected in the 14 wastewater samples collected from seven Canadian sewage treatment plants; those occurring at the highest concentrations were atenolol, acebutolol, sotalol, and metroprolol, with overall median concentrations of 1370, 339, 282, and 257 ng/L, respectively. However, there was only a small decrease in the median concentrations of these beta-blockers between the primary and final effluent, suggesting that these drugs are not easily removed by the sewage treatment processes. As a result of selective extraction and effective removal of coextractives, no matrix effect was observed for the samples during LC-MS/MS analyses.     

Determination of apramycin in animal feeds by solid-phase extraction and liquid chromatography with precolumn derivatization and fluorescence detection

A high-performance liquid chromatographic method for determining apramycin in animal feeds was developed. Apramycin in feeds was extracted with 0.1 M HCl solution and cleaned up with an MCX solid-phase extraction column. The purified extract was derivatized with o-phthaldehyde, and components were separated on a C18 column and detected with a fluorescence detector. Mass spectrometric data confirmed that apramycin was derivatized at all the 4 primary amines on the apramycin molecule. Average recoveries at 8 included levels (5, 10, 20, 40, 80, 200, 400, and 2000 mg/kg) ranged from 92.2 to 100.5%, and the coefficients of variation were < 6.5%. Standard curves were linear over the range 0.05 to 10 microg/mL. The detection and quantitation limits were determined to be 0.2 and 1.0 mg/kg, respectively.     

Determination of naphthalenesulfonates in water by on-line ion-pair solid-phase extraction and ion-pair liquid chromatography with fast-scanning fluorescence detection

A fast analytical method for quantifying a mixture of 12 naphthalenesulfonates and naphthalenedisulfonates has been developed. This method consists of on-line ion-pair solid-phase extraction with PLRP-s sorbent and ion-pair liquid-chromatography using fast-scanning fluorescence spectrometer as a detection system and multivariate calibration. As complete separation is unnecessary, the compounds were analysed in isocratic conditions and the chromatographic analysis took only 25 min. Three-way partial least-squares (PLS) was used to carry out multivariate calibration for spiked tap water. In these conditions, quantification limits were between 0.01 and 3 μg l⁻¹. Repeatability was also evaluated and relative standard deviations (n=3) were between 0.5 and 4, depending on the compound. Finally, spiked tap and Ebro river waters were analysed to evaluate prediction capability of the method.     

Determination of isopropyl-9H-thioxanthen-9-one in packaged beverages by solid-phase extraction clean-up and liquid chromatography with tandem mass spectrometry detection

A simple method was developed and validated for the trace determination of 2-isopropylthioxanthone (ITX) in packaged drinks. Samples were extracted from the food matrix using acetonitrile:water (60:40, v/v), and further subjected to clean-up and preconcentration using solid-phase extraction prior to analysis by liquid chromatography-tandem mass spectrometry using multiple reaction monitoring (MRM) mode. The use of 2-isopropyl-[(2)H7]thioxanthen-9-one was incorporated into the method as an internal standard. Excellent 3-day interday precision data (RSD 0.72%, n=10), and intraday precision data (RSD 0.52%, n=10) were obtained on a 0.10 microg/L standard solution. Spiked samples (n=8) were used to gauge the accuracy of the method at the concentration levels of 2.5, 100, and 500 microg/kg in food; recoveries ranged from 97.0 to 103.0%. These excellent validation data suggest the exciting possibility of using this method for the determination of low levels of ITX migrating from printed food packaging materials into beverages with a method quantitation limit of 0.50 microg/kg. For the first time, analysis on a range of milk, juice, tea and yoghurt drinks, as well as their respective food packaging materials were performed for comparative studies on their ITX content.     

Determination of cardiovascular drugs in sewage sludge by matrix solid-phase dispersion and ultra-performance liquid chromatography tandem mass spectrometry

Analytical and Bioanalytical Chemistry - The current study presents a single step sample preparation procedure for the simultaneous determination of five antihypertensive (propranolol, losartan,...     

Determination of aflatoxin M1 in milk using solid-phase extraction and high-performance liquid chromatography with fluorescence detection

Solid-phase extraction of aflatoxin Ml from milk using Diapak S16M and Diapak S solid-phase extraction cartridges followed by HPLC determination with a Flyuorat-02 fluorescence detector was studied.     

Determination of alkylphenol and alkylphenolethoxylates in biota by liquid chromatography with detection by tandem mass spectrometry and fluorescence spectroscopy

A quantitative method for the simultaneous determination of octylphenol, nonylphenol and the corresponding ethoxylates (1 to 5) in biota is presented. Extraction methods were developed for egg and fish matrices based on accelerated solvent extraction followed by a solid-phase extraction cleanup, using octadecylsilica or aminopropyl cartridges. Identification and quantitation were accomplished by liquid chromatography-electrospray tandem mass spectrometry (LC-MS-MS) and compared to the traditional liquid chromatography with fluorescence spectroscopy detection. LC-MS-MS provides high sensitivity and specificity required for these complex matrices and an accurate quantitation with the use of 13C-labeled internal standards. Quantitation limits by LC-MS-MS ranged from 4 to 12 ng/g in eggs, and from 6 to 22 ng/g in fish samples. These methods were successfully applied to osprey eggs from the Chesapeake Bay and fish from the Great Lakes area. Total levels found in osprey egg samples were up to 18 ng/g wet mass and as high as 8.2 microg/g wet mass in the fish samples.     

Determination of sulfonylurea herbicides in water using solid-phase extraction followed by liquid chromatography with electrospray ion trap mass spectrometry

A method has been developed for confirmation and quantitation of ten sulfonylurea herbicides (nicosufuron, thifensulfuron-methyl, metsulfuron-methyl, sulfometuron-methyl, chlorsulfuron, ethametsulfuron-methyl, tribenuron, bensulfuron-methyl, pyrazosulfuron-ethyl and chlorimuron-ethyl) in water samples. Herbicides were extracted from water by off-line solid-phase extraction (SPE). Different types of absorbents were evaluated: silica-based ODS-C₁₈ and two polymeric sorbents, Cleanert HXN and Oasis HLB. Analyte determination and quantitation was performed by liquid chromatography with electrospray mass spectrometry (LC-ESI-MS) instrumentation, equipped with ion trap mass filter. Confirmatory analysis was carried out by LC/MS/MS. MS data acquisition was performed by a single or two-ion extracted ion monitoring program. The ten herbicides were measured in fortified tap water. Average recoveries of the nine analytes (except for tribenuron) from water samples were in the range of 77–109%, and the RSD ranged from 0.3 to 14.5%. The limit of detections (LODs) varied from 6 to 34.8 ng/L.     

Determination of quinolone residues in shrimp using liquid chromatography with fluorescence detection and residue confirmation by mass spectrometry

The quinolones, oxolinic acid (OXO), flumequine (FLU), and nalidixic acid (NAL), are antibacterial drugs effective against Gram-negative bacteria. Quinolones are used in both human and veterinary medicine, but are currently not approved by the U.S. Food and Drug Administration for use in food fish. A liquid chromatography-fluorescence (LC-FL) method was developed to determine OXO, FLU, and NAL residues in shrimp. An additional liquid chromatography-mass spectrometry (LC-MSⁿ) method was created to confirm these residues using the same sample extract. Samples were prepared with a simple ethyl acetate extraction followed by solvent exchange into 0.2% formic acid and cleaned-up with hexane. Reverse phase chromatography was used to separate the three compounds in both procedures. For the LC-FL determinative method, fluorescence emission was monitored at 369 nm with excitation at 327 nm. With electrospray ionization, the three most abundant ions from the MS³ product ion spectrum were used to identify OXO, FLU, and NAL in the confirmation procedure. Shrimp samples fortified at levels ranging from 7.5 to 100 ng g⁻¹ were used to validate both methods.     

Determination of sedative hypnotics in sewage sludge by pressurized liquid extraction with high‐performance liquid chromatography and tandem mass spectrometry

This paper describes a method for the determination of eight sedative hypnotics (benzodiazepines and barbiturates) in sewage sludge using pressurized liquid extraction and liquid chromatography with tandem mass spectrometry. Pressurized liquid extraction operating conditions were optimized and maximum recoveries were reached using methanol under the following operational conditions: 100ºC, 1500 psi, extraction time of 5 min, one extraction cycle, flush volume of 60% and purge time of 120 s. Pressurized liquid extraction recoveries were higher than 88% for all the compounds except for carbamazepine (55%). The repeatability and reproducibility between days, expressed as relative standard deviation (n = 5), were lower than 6 and 10%, respectively. The detection limits for all compounds were lower than 12.5 μg/kg of dry weight. The method was applied to determine benzodiazepines and barbiturates in sewage sludge from urban sewage treatment plants, and carbamazepine showed the highest concentration (7.9–18.9 μg/kg dry weight).     

Determination of clozapine in human plasma by solid-phase extraction and liquid chromatography with amperometric detection

Summary A sensitive and selective high-performance liquid chromatographic method has been developed for monitoring clozapine levels in human plasma. Chromatography was performed on a reversed-phase column (C₈, 150 mm×4.6 mm i.d., 5 μm) with acetonitrile-aqueous sodium acetate solution, 88∶12 (v/v), as mobile phase; the flow rate was 1 mL min⁻¹. Clozapine oxidation at +800 mV was detected amperometrically. Response was linearly dependent on concentration over the range 50–1500 ng mL⁻¹ clozapine in plasma. Sample preparation by solid-phase extraction before HPLC analysis gave high extraction yield (94%). The accuracy and precision of the method were both very good (recovery: 97%;RSD<3.3%).     

Determination of quinolones in water samples by solid-phase extraction and liquid chromatography with fluorimetric detection

A method is reported for the determination, in water samples, of 10 quinolones which are used as veterinary drugs. Analytes are isolated from samples by solid-phase extraction (SPE) and analysed by reversed-phase high-performance liquid chromatography using fluorimetric detection. A solid-phase extraction procedure based on retention on HBL OASIS cartridges and elution with a mixture of acetonitrile-water in basic medium is suitable for pre-concentration of the analytes. Pre-concentration factors up to 250 can be obtained. The quinolones are separated with an octyl silica-based column and mobile phases consisting of aqueous oxalic acid solutions and acetonitrile mixtures. The attained detection limits of the whole process are in the ng l(-1) level when 250 ml of water sample is processed. Recovery rates, from natural water samples spiked at 2060 ng l(-1) level, range from 70 to 100% and common standard deviation are about 6-12%.     

Determination of hydroxy-PCBs in urine by gas chromatography/mass spectrometry with solid-phase extraction and derivatization

A sensitive derivatization and extraction method is proposed for the determination of hydroxy-PCBs in urine. Phenolic hydroxyl groups of PCBs were allowed to react with five different reagents such as iodomethane, iodoethane, iodopropane, BSTFA and MTBSTFA. Propylated products at 100 °C for 30 min showed the best sensitivity with mass selective detector. Extraction recoveries and relative standard deviations of hydroxy-PCBs by SPE using C2 column were in the range of 78.0-112.3% and 2.5-9.6%, respectively. Instrumental detection limits for derivatized hydroxy-PCBs were in the range of 1-2 pg and were 10-1000 times more sensitive than those of non-derivatized hydroxy-PCBs. The correlation coefficients of the linear regression curves exceed 0.99, and the intra- and inter-day precisions were evaluated by RSDs within 10% at the concentrations of 0.4 and 4.0 ng/mL.     

Determination of alkylbenzene metabolites in groundwater by solid-phase extraction and liquid chromatography-tandem mass spectrometry

Benzylsuccinate (BSA), methylbenzylsuccinate (methylBSA), and ethylbenzylsuccinate (ethylBSA) are unambiguous anaerobic biotransformation products from toluene, xylenes, and ethylbenzene decay, respectively, and may be used to indicate intrinsic bioremediation is occurring at hydrocarbon-contaminated sites. In order to improve upon current methods that detect and quantify anaerobic hydrocarbon metabolites in field samples, solid-phase extraction (SPE) and direct sample injection methods coupled with liquid chromatography-tandem mass spectrometry (LC-MS-MS) were evaluated. In laboratory studies, recoveries of authentic standards of non-deuterated or deuterated benzylsuccinates and toluates ranged from 80 to 106% with relative standard errors ranging from 2 to 4%. The method detection limits for these analytes using SPE-LC-MS-MS ranged from 0.006 to 0.029 microg/L whereas those for direct injection-LC-MS-MS ranged from 0.61 to 1.5 microg/L. Given the increased sensitivity of using SPE coupled with LC-MS-MS, this technique was then used to analyze for the presence of putative anaerobic alkylbenzene metabolites in groundwater from a hydrocarbon-contaminated site where single-well push-pull tests were conducted using deuterated aromatic hydrocarbons. Both deuterated and non-deuterated benzylsuccinates and toluates were successfully detected and quantified in field samples using this method.     

Determination of bisphenol A in sewage effluent and sludge by solid-phase and supercritical fluid extraction and gas chromatography/mass spectrometry

Methods have been developed for the determination of bisphenol A (BPA) residues in municipal sewage and sludge samples. BPA in wastewater samples was enriched with a C18 solid-phase extraction cartridge, eluted with acetone, and converted to the pentafluoropropionyl derivative. For sludge samples, BPA was acetylated and extracted with supercritical carbon dioxide. In both cases, BPA-d16 was used as a surrogate to monitor extraction efficiency. Final analyses of derivatized sample extracts were performed by gas chromatography/mass spectrometry operating in the electron impact mode. For water samples, mean recoveries and standard deviations were 89 +/- 6, 94 +/- 4, and 85 +/- 7% at fortification levels of 1, 0.1, and 0.025 microg/L, respectively, with a method detection limit of 0.006 microg/L. For solid waste samples, mean recoveries and standard deviations were 93 +/- 5 and 92 +/- 6% at fortification levels of 2.5 and 0.25 microg/g, respectively, and the method detection limit was 0.05 microg/g. For the Canadian samples under investigation, concentrations of BPA ranged from 49.9 to 0.031 microg/L in sewage influent and effluent, and from 36.7 to 0.104 microg/g in sludge.