Manipulating the surface properties of polyacrylamide with nitrogen plasma

Polyacrylamide (PAL) was physically adsorbed onto a hydroxylated silicon surface to form a uniform PAL film and the up-top PAL thin film was treated by nitrogen (N₂) plasma for surface modification. The atomic composition of the modified surface of the PAL film adsorbed on silicon substrate was analyzed with Fourier Transform Infrared Spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The surface energy of PAL film was calculated from the data of contact angle of three-probe liquid. The FTIR results show an increase of peak intensity at 1214 cm⁻¹ (NH₂ stretch vibration) after the nitrogen plasma treatment, which confirms that the nitrogen was grafted to the PAL surface in the process of N₂-plasma treatment. The XPS results show that the ratio of relative intensity of N1s to O1s increases with increasing the plasma treatment time, which further affirms the formation of the amine groups on the PAL surface after the nitrogen plasma treatment. The surface tension increases with increasing the plasma grafting time. However, the surface energy decreases rapidly at the early stage when stored in air and approaches to an equilibrium value. It suggests that some physically-adsorbed ions and alkyl radicals on PAL surface can rapidly lose their activities. The increase of the surface tension of the plasma treated PLA films is due to the amine groups covalently grafted to PAL surface.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface characterization and barrier properties of plasma‐modified polyethersulfone/layered silicate nanocomposites

This study describes the preparation of polyethersulfone (PES)/layered silicate nanocomposites (PLSNs) by mixing PES polymer chain into organically‐modified layered silicate in 1‐methyl‐2‐pyrrolidinone (NMP) solution. Both X‐ray diffraction data and transmission electron microscopy images of PLSNs indicate that the silicate layers were almost exfoliated and randomly distributed into the PES matrix. The mechanical and barrier properties of PLSNs show remarkable enhancement in the storage modulus and water/oxygen permeability when compared with that of neat PES matrix. Surfaces modification of PES and PLSN films with various treated times, system pressures, and radio frequency (RF) powers were performed using a mixture of oxygen (O₂) and nitrogen (N₂) plasmas. The topographical and physical properties of plasma‐modified PES and PLSN surfaces were investigated using scanning probe microscopy (SPM), contact‐angle measurements, and X‐ray photoelectron spectroscopy (XPS). These results indicate that the surface roughness of PLSNs with the same condition of plasma modification is lower than that of neat PES matrix and is probably due to the increase of stiffness with the presence of inorganic layered silicates in PES matrix. The surface properties of the PES and PLSNs are also changed from hydrophobic to hydrophilic. The XPS spectra suggest that the exposure of the PES and PLSNs to the plasmas led to the combination of etching reactions of polymer surface initiated by plasma and the following addition reactions of new oxygen‐ and nitrogen‐containing functional groups onto polymer surfaces to change their surface properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3185–3194, 2006     

Surface Behavior of Polyamide 6 Modified by Barrier Plasma in Oxygen and Nitrogen

Polyamide (PA) 6 was modified by diffuse coplanar surface barrier discharge (DCSBD) plasma in an atmosphere of nitrogen and oxygen. The surface roughness decrease of PA 6 was detected by AFM and nano-indentation after modification in DCSBD plasma. A significant increase in O/C and N/C ratios of plasma-modified PA 6 using XPS analysis was found. The results show the importance of introducing oxygenic polar functional groups on the polymeric surface in order to increase its surface energy during a short time of plasma activation. The modification of PA 6 by DCSBD oxygen plasma was more efficient than by nitrogen plasma.     

Introduction of Primary Amino Groups on Poly(ethylene terephthalate) Surfaces by Ammonia and a Mix of Nitrogen and Hydrogen Plasma

With the aim of introducing primary amino groups on the surface of poly(ethylene terephthalate) (PET), two methods were compared—the use of ammonia or a combination of nitrogen and hydrogen low-pressure microwave plasma. Several plasma parameters were optimized on the reactor to increase the –NH₂ surface density, which was estimated by colorimetric titration and X-ray photoelectron spectroscopy (XPS). These techniques show that whatever the plasma treatment, almost 2 –NH₂/nm2 are incorporated on PET films. Emission spectroscopy highlighted a correlation between the density of primary amino groups and the ratio between an NH peak intensity and an Ar peak intensity (I_NH/I_Ar). Variation in surface hydrophilicity with aging in air after plasma treatment was monitored with contact angle measurements and showed a hydrophobic recovery. This was confirmed by XPS, which suggests also that surfaces treated by NH₃ plasma are more stable than surfaces treated by N₂/H₂.     

Chemical changes of polymeric surfaces after modification with multi-source cluster deposition

A new process for surface modification of polymers with multi-source cluster deposition apparatus has been reported in our previous work. The apparatus simultaneously supplies reactant of ammonium sulfamate and activator of energetic Ar(+) ion. In this work chemical changes are analyzed on the basis of XPS spectra and the relations of contact angle and platelet adhesion with chemical changes are discussed. Polymer film, setting on a turning holder, was irradiated by Ar(+) ions during bombardment with ammonium sulfamate clusters. The Ar(+) ion source served for activation of polymer surface and a cluster ion source supplied ammonium sulfamate molecules to react with activated surface. After thorough washing with deionized sterile water, the modified surfaces were evaluated in terms of contact angle of water, elemental composition and binding state on XPS and platelet adhesion with platelet rich plasma (PRP). The modification of polysulfone decreased the contact angle of water on surfaces from 82.6 down to 34.5 degrees. The adhesion number of platelets were decreased to one-tenth of the original surface. Ammonium, amine, sulfate and thiophene combinations were formed on the modified surfaces. The primary studies showed successful modification of polysulfone with ammonium sulfamate by assistance of Ar(+) ion irradiation. The polar groups like N-sulfate were formed on surfaces and contribute to the decrease of surface contact angle and adhesion number of platelets. Since the same process can also be applied to other polymeric materials with various substrates, combining with the features of no solvent and no topographic changes, this method might be developed in a promising way for modification of polymers.     

Influence of O2 Plasma on Surface Properties of PC-TiO2 Nanocomposite Film

In this work, polycarbonate-TiO₂ nanocomposite films were prepared with different percentages. The aim was to consider the effect of O₂ LF plasma (50 Hz) on the hydrophilicity, surface energy, and surface morphology of polycarbonate and polycarbonate-TiO₂ nanocomposite. Structure of samples was determined by using X-ray diffraction analysis. In comparison with the reference sample, the samples’ structure did not change after plasma treatment. Surface properties of polycarbonate and polycarbonate-TiO₂ nanocomposite films were studied by X-ray photoelectron spectroscopy (XPS), contact angle measurement, atomic force microscopy (AFM), and Vickers microhardness tester. XPS analysis showed that the surface of samples became more oxidized due to plasma treatment. The water contact angle significantly decreased from 88° to 15° after plasma treatment. It was observed that the hardness of the nanocomposite films was not modified after plasma treatment.     

Surface modification of low-density polyethylene by inductively coupled argon plasma

The surface chemistry and nanotopography of low-density polyethylene (LDPE) were modified by downstream, inductively coupled, radio frequency (rf) Ar plasma without inducing surface damage. The extent of surface modification was controlled by the applied ion energy fluence, determined from the plasma ion density measured with a Langmuir probe. The treated LDPE surfaces were characterized by atomic force microscope (AFM) imaging, contact angle measurements, and X-ray photoelectron spectroscopy (XPS). Analysis of AFM surface images confirmed that topography changes occurred at the nanoscale and that surface damage was insignificant. Contact angle measurements demonstrated an enhancement of the surface hydrophilicity with the increase of the plasma power. XPS results showed surface chemistry changes involving the development of different carbon-oxygen functionalities that increased the surface hydrophilicity. Physical and chemical surface modification was achieved under conditions conducive to high-density inductively coupled rf plasma.     

Effect of plasma treatment on cellulose fiber

Cotton cellulose fibers were modified in inert plasma. Surface morphology of the modified fibers was studied by SEM and changes in the surface composition by XPS and FTIR. Standard goniometry was used for determination of contact angle as a function of modified fiber aging. Absorptivity of modified fibers was determined by gravimetry and fiber width in physiological solution, simulating body liquids, by confocal microscopy. Antibacterial effect of pristine and plasma treated samples was examined by following growth of Escherichia coli. Plasma treatment led to surface ablation, changes in surface morphology and fiber width. Surface of the plasma modified fibers was oxidized and their water absorptivity was reduced. The plasma modification did not affect E. coli growth substantially.     

Surface characterization of plasma‐modified poly(ethylene terephthalate) film surfaces

Poly(ethylene terephthalate) (PET) film surfaces were modified by argon (Ar), oxygen (O₂), hydrogen (H₂), nitrogen (N₂), and ammonia (NH₃) plasmas, and the plasma‐modified PET surfaces were investigated with scanning probe microscopy, contact‐angle measurements, and X‐ray photoelectron spectroscopy to characterize the surfaces. The exposure of the PET film surfaces to the plasmas led to the etching process on the surfaces and to changes in the topography of the surfaces. The etching rate and surface roughness were closely related to what kind of plasma was used and how high the radio frequency (RF) power was that was input into the plasmas. The etching rate was in the order of O₂ plasma > H₂ plasma > N₂ plasma > Ar plasma > NH₃ plasma, and the surface roughness was in the order of NH₃ plasma > N₂ plasma > H₂ plasma > Ar plasma > O₂ plasma. Heavy etching reactions did not always lead to large increases in the surface roughness. The plasmas also led to changes in the surface properties of the PET surfaces from hydrophobic to hydrophilic; and the contact angle of water on the surfaces decreased. Modification reactions occurring on the PET surfaces depended on what plasma had been used for the modification. The O₂, Ar, H₂, and N₂ plasmas modified mainly CH₂ or phenyl rings rather than ester groups in the PET polymer chains to form C? O groups. On the other hand, the NH₃ plasma modified ester groups to form C? O groups. Aging effects of the plasma‐modified PET film surfaces continued as long as 15 days after the modification was finished. The aging effects were related to the movement of C?O groups in ester residues toward the topmost layer and to the movement of C? O groups away from the topmost layer. Such movement of the C?O groups could occur within at least 3 nm from the surface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3727–3740, 2004     

Expanded poly(tetrafluoroethylene) membrane surface modification using acetylene/nitrogen plasma treatment

In this article, expanded poly(tetrafluoroethylene) (e-PTFE) membrane surface modification was carried out using acetylene/nitrogen plasma treatment (p-e-PTFE). The variation in surface morphology of the p-e-PTFE membranes was confirmed by FTIR-ATR, scanning electron microscopy (SEM), and contact angle measurements. It was found that the surface hydrophilicity increased with increasing nitrogen content in the feed gas mixture, RF power, and plasma treatment time. The surface pore size decreased with increasing RF power and plasma treatment time. The water contact angles of the modified e-PTFE membrane decreased from 125.8° to 34.1° through the acetylene/nitrogen plasma treatment.     

Tailoring the surface chemistry of carbon fiber and E‐glass composites for improved adhesion

The main challenges in the manufacture of composite materials are low surface energy and the presence of silicon‐containing contaminants, both of which greatly reduce surface adhesive strength. In this study, carbon fiber (CF) and E‐glass epoxy resin composites were surface treated with the Accelerated Thermo‐molecular adhesion Process (ATmaP). ATmaP is a multiaction surface treatment process where tailored nitrogen and oxygen functionalities are generated on the surface of the sample through the vaporization and atomization of n‐methylpyrrolidone solution, injected via specially designed flame‐treatment equipment. The treated surfaces of the polymer composites were analyzed using XPS, time of flight secondary ion mass spectrometry (ToF‐SIMS), contact angle (CA) analysis and direct adhesion measurements. ATmaP treatment increased the surface concentration of polar functional groups while reducing surface contamination, resulting in increased adhesion strength. XPS and ToF‐SIMS showed a significant decrease in silicon‐containing species on the surface after ATmaP treatment. E‐glass composite showed higher adhesion strength than CF composite, correlating with higher surface energy, higher concentrations of nitrogen and C?O functional groups (from XPS) and higher concentrations of oxygen and nitrogen‐containing functional groups (particularly C₂H₃O⁺ and C₂H₅NO⁺ molecular ions, from ToF‐SIMS). Copyright © 2010 John Wiley & Sons, Ltd.     

Multitechnique surface spectroscopic studies of plasma modified polymers III. H2O and O2/H2O plasma modified poly(methyl methacrylate)s

The surfaces of poly(methyl methacrylate) (PMMA) films modified by O₂H₂O and H₂O radio-frequency glow discharge plasmas were studied using electron spectroscopy for chemical analysis (ESCA or XPS), low energy ion scattering (LEISS or ISS), Fourier transform IR spectroscopy (FTIR) with attenuated total reflectance (ATR) sampling, and critical surface energy from contact angle measurements. The extent and nature of modification with respect to promotion of a hydrophilic surface compared to the hydrophobic surface of the unmodified PMMA has been probed. Results show drastic decreases in C/O ratio at the near surface, which increases to that of the unmodified PMMA as deeper cross sections are analyzed. In addition peak fitting of ESCA data correlated with FTIR functional group information allows for the qualitative and quantitative analysis of the resulting bonding and structure of the modified layer. From these results combined with the polarity and surface energy differences obtained from contact angle measurements, the structural changes are discussed with respect to plasma reaction mechanisms and differences in the structure of the modified polymer films.     

木粉/聚乙烯复合材料的等离子体表面处理——等离子体处理时间对复合材料表面特性的影响

为改善木粉/聚乙烯复合材料的表面粘接性,实现木粉/聚乙烯复合材料的无缝连接,利用低温等离子体处理技术,对木粉/聚乙烯复合材料进行了表面处理.采用接触角测试、傅立叶变换红外光谱分析(FTIR)以及X射线光电子能谱分析(XPS)研究了等离子体处理前后复合材料表面性能的变化.试验结果表明,经等离子体处理后,复合材料表面的接触角减小,表面润湿性得以改善;FTIR分析结果表明,经等离子体处理后,复合材料表面有—OH、—C=O和—O—C=O基团生成;XPS分析表明,经等离子体处理后,复合材料表面含氧基团的含量增加,在较短的时间内表面氧元素含量增加会达到平衡,且生成大量的—O—C=O基团。     

Photochemical modification of diamond films: introduction of perfluorooctyl functional groups on their surface

Photolysis of perfluoroazooctane with diamond films led the chemical modification of the surface to introduce perfluorooctyl functional groups, confirmed by means of Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and time-of-flight secondary ion mass spectrometry measurements. Diamond films modified with fluorine moieties showed improved frictional property and reduction of surface energy, as evaluated by contact angle to water, compared with a pristine diamond film. The contact angle and friction coefficient of chemically modified diamond film are 118 degrees and 0.1, respectively. The results of the value of the contact angle depending on irradiation times are consistent with those of the F/C ratio of fluorinated diamond films by monitoring with XPS.     

聚甲基戊烯膜式氧合器表面碳酸酐酶的固定化及性能研究

聚甲基戊烯(PMP)膜式氧合器表面先用水等离子体改性,以引入羟基官能团;再以溴化氰为偶联剂,将碳酸酐酶(CA)偶联至其表面.改性后用X射线光电子能谱(XPS)、表面接触角及酶活性测定等方法研究PMP表面性能变化.结果表明,等离子体处理后,在PMP表面引入了大量的含氧官能团,与水的表面接触角从103.37°降低至50.01°.再将CA引入PMP表面后,与水的表面接触角进一步降低至39.23°;XPS的C1谱图中出现蛋白质的特征峰;以对硝基苯酚乙酸酯为底物,测得表面接枝CA的活性达到理论单分子层接枝活性的73%.改性后PMP表面物理化学性质的变化证明本文方法确实能成功地将羟基官能团、CA引入其表面.本方法有望应用在膜式氧合器上以提高其清除血液中CO2的能力.     

Increasing the Hydrophobicity of a PP Film Using a Helium/CF<Subscript>4</Subscript> DBD Treatment at Atmospheric Pressure

Plasma surface modification is widely used to tailor the surface properties of polymeric materials. Most treatments are performed using low pressure plasma systems, but recently, atmospheric dielectric barrier discharges (DBDs) have appeared as interesting alternatives. Therefore, in this paper, an atmospheric He + CF₄ DBD is used to increase the hydrophobicity of a polypropylene (PP) film. The surface characterization of the PP film is performed using contact angle measurements, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Results show that the hydrophobic properties of the polymer films are greatly enhanced after plasma treatment as evidenced by an increased contact angle. The incorporation of fluorine on the surface is significant (45 at%), demonstrating the ability of the used DBD set-up to generate fluorine-containing functional groups on the PP surface.     

Surface analysis of nitride layers formed on Fe‐based alloys through plasma nitride process

Nitriding phenomena that occur on the surfaces of pure Fe and Fe? Cr alloy (16 wt% Cr) samples were investigated. An Ar + N₂ mixture‐gas glow‐discharge plasma was used so that surface nitriding could occur on a clean surface etched by Ar⁺ ion sputtering. In addition, the metal substrates were kept at a low temperature to suppress the diffusion of nitrogen. These plasma‐nitriding conditions enabled us to characterize the surface reaction between nitrogen radicals and the metal substrates. The emission characteristics of the band heads of the nitrogen molecule ion (N₂⁺) and nitrogen molecule from the glow‐discharge plasma suggest that the active nitrogen molecule is probably the major nitriding reactant. AES and angle‐resolved XPS were used to characterize the thickness of the nitride layer and the concentration of elements and chemical species in the nitride layer. The thickness of the nitride layer did not depend on the metal substrate type. An oxide layer with a thickness of a few nanometers was formed on the top of the nitride layer during the nitriding process. The oxide layer consisted of several species of N_x‐Fe_y‐O, NO⁺, and NO₂^?. In the Fe? Cr alloy sample, these oxide species could be reduced because chromium is preferentially nitrided. Copyright © 2009 John Wiley & Sons, Ltd.     

Surface roughness and hydrophilicity enhancement of polyolefin‐based membranes by three kinds of plasma methods

The introduction of antibacterial property, conductivity, wettability and antithrombogenicity into polyolefin‐based membranes has evoked much attention, which can be achieved by coating hydrophilic polymers. Therefore, it is necessary to modify the roughness and hydrophilicity of polyolefin‐based membranes to enhance the coating ability. In this paper, three kinds of plasma methods, including inductively coupled (ICP) plasma, radio frequency low pressure (RFP) plasma and atmospheric dielectric barrier discharge (DBD) plasma, were used to modify the surface of the polyethylene (PE), polypropylene (PP) and polyester‐polypropylene (PET–PP) membranes. The surface roughness of the plasma‐modified PE, PP and PET–PP films was investigated by scanning electron microscopy (SEM) and atomic force microscope (AFM). The polar functional groups of films were observed by energy dispersive spectrometer (EDX) and X‐ray photoelectron spectroscopy (XPS). Besides, the hydrophilicity of the plasma‐modified PE, PP and PET–PP films was evaluated by water contact angle measurement. It was found that the surface roughness and hydrophilicity of plasma‐modified PE, PP and PET–PP films increased with the generation of oxygen‐containing functional groups (i.e. C―O, and C?O). The PET–PP membranes were treated by RFP plasma at different processing powers and times. These results indicated that plasma is an effective way to modify films, and the treatment time and power of plasma had a certain accumulation effect on the membranes' hydrophilicity. As for the roughness and hydrophilicity, the DBD plasma modifies the PE film, which is the optimum way to get the ideal roughness and hydrophilicity. Copyright © 2015 John Wiley & Sons, Ltd.     

Polymer matrix of polyethylene porous films functionalized by electrical discharge plasma

The polyethylene porous films were treated by dielectric surface barrier discharge (DSBD) plasma at atmospheric pressure in oxygen (O₂) or nitrogen (N₂), and by radio-frequency discharge (RFD) plasma in air at reduced pressure 46 Pa. The surface energy of films was carried out by direct measurements of contact angles of six testing liquids. The strength of adhesive joints in the system modified polyethylene porous films - polyacrylate was measured by peeling of the joints under the angle of 90°. The significant increase of the surface energy and its polar component of polyethylene porous films modified by all types of plasma were observed. The higher strengths of adhesive joints were found for modification of polyethylene porous films by radio-frequency discharge plasma in comparison with modification of the films by barrier discharge plasma.