Nafion修饰电极还原计时电位溶出法的理论和验证

本文推导了Nafion修饰电极还原计时电位溶出法的过渡时间和电位-时间曲线方程式。经过验证,实验结果与理论相符。     

超微盘电极上电位溶出分析法理论

本文提出了超微盘电极上电位溶出分析法理论,内容包括:过渡时间(τ)方程式、电位(E)-时间(t)曲线方程式及微分电位溶出分析法dt/dE-E曲线方程式,并对该曲线的性质进行了论述。     

镧在低共熔溶剂中的电沉积研究

以氯化胆碱/尿素低共熔溶剂为介质通过恒电位沉积法成功制备了形状和尺寸均一的橄榄状镧粒子. 采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线能量色散谱（EDX）和X射线光电子能谱（XPS）等技术对所制备的样品进行表征. 同时,研究了沉积电位、温度和时间等因素对样品尺寸、形貌的影响,确定恒电位法制备橄榄状镧粒子的优化工艺条件为沉积电位-1.7 V、温度80 ^oC和沉积时间15 min.     

恒电位组装的硫醇单层膜的电化学性质

采用恒电位组装的方法在金基底上制备了十二硫醇单层膜,用反射傅立叶红外光谱、循环伏安法和电化学阻抗谱对得到的硫醇膜进行了表征.结果表明,恒电位组装1 min即可在金基底上形成没有针孔缺陷的硫醇单层膜.随着恒电位组装时间的增加,硫醇膜上的凹陷点缺陷逐渐减少,致密程度逐渐增加.当恒电位组装时间达到5 min时,得到的硫醇膜与自组装24 h的硫醇膜具有相当的致密度和更少的凹陷点缺陷.     

n-InP/Fe3+, Fe2+界面在小信号电流阶跃下的暂态行为

应用小信号电流阶跃法研究了光照下n-InP/Fe~(3+), Fe~(2+)界面, 此时电位变化符合双指数规律, 这和理论推导是一致的。在时间很短时, 电位与时间成线性关系, 从直线斜率可求出空间电荷区电容。     

葡萄糖酸钠对萘系减水剂在水泥表面吸附的影响

研究了葡萄糖酸钠对掺萘系减水剂的水泥净浆流动度和凝结时间的影响,葡萄糖酸钠的掺入增加了浆体的流动度和凝结时间.采用紫外-可见光分光光度计和Zeta电位仪,分别测试了水泥颗粒对萘系减水剂的吸附量及水泥颗粒的电位.结果表明,吸附量随着减水剂掺量的增加而增加.减水剂和葡萄糖酸钠在水泥表面存在竞争吸附,葡萄糖酸钠的掺入抑制了减水剂的吸附;但减水剂和葡萄糖酸钠同时吸附在水泥表面增加了水泥表面电位,延缓了水泥水化.     

二氧化碳和氧气的快速电化学方法联合测定

根据Ｏ２和ＣＯ２在二甲亚砜（ＤＭＳＯ）介质中Ｐｔ电极上的伏安特性，采用微电极并结构计算机控制的电位调制技术，建立了快速联合测定ＣＯ２和Ｏ２的调制电位脉冲库仑法和调制电位脉冲电流法，取得了满意的结果。一次测量时间快达４０ｍｓ。ＣＯ２检测范围０￣１０％（体积百分比）；Ｏ２检测范围不受限制。通过编程设计特定的调制电位－时间波形，可保持连续检测的长期稳定性。     

用流动电位法表征纳滤膜的结构及性能

利用测量流动电位的方法考察了纳滤膜的表面电学性能对纳滤膜的截留性能的影响.首先,采用不同功能层材料制备了复合纳滤(NF)膜,考察功能层的交联时间、单体结构等对表面电性能的影响,研究纳滤膜对不同无机盐的选择截留性能与表面电性能的关系.通过流动电位法测定纳滤膜的表面电学参数,如流动电位(ΔE)、zeta电位(ζ)和表面电荷密度(σd).实验表明,这些电学参数的变化与功能层交联时间和纳滤膜截留率的变化一致,在交联时间为45 s时,3种电学参数的绝对值均最大,而纳滤膜对无机盐的截留率也最大.复合纳滤膜zeta电位的绝对值(|ζ|)按照Na2SO4>MgSO4>MgCl2变化,同截留率的变化相同.带侧基单体交联后得到的纳滤膜的表面电性能参数的绝对值小于不带侧基单体的.因此,流动电位法可用于研究复合纳滤膜的截留机理和功能层结构.     

交流极谱中毛细管特性的一些影响因素

通过对0.5NHCl底液中镉波的实验,观察到在峰电位时,交流极谱电流和汞滴下时间的关系是一正幂函数图形,滴下时间和汞柱高的关系是一支双曲线;若在直流极谱中叠加交流电压,则电毛细管曲线曲率增大,用交流极谱法在峰电位时测定汞滴下时间,比用直流极谱法时约小2％;在峰电位时,电解液厚度每增加1厘米,能使汞滴下时间增长约3％。     

恒电位氧化改性石墨毡及其氧还原电极的电化学性能

分别采用循环伏安改性法和恒电位氧化法对石墨毡进行改性处理,并采用循环伏安法对其电化学性能进行研究,实验结果表明,恒电位氧化改性较循环伏安改性的石墨毡有较好的氧还原活性。通过XRD、FTIR、接触角和CV针对恒电位氧化处理石墨毡进行了进一步的测试。测试结果显示,随恒电位氧化时间的增加,石墨毡表面亲水性含氧官能团增加,润湿性增强。恒电位氧化改性处理25 min的石墨毡氧还原峰电位及电流密度分别为~-0.43 V和~0.003 4 mA·cm^-2,显示出很好的电化学催化性能。基于以上结果,恒电位氧化法改性处理能够极大提高石墨毡的氧阴极活性。     

电活化玻碳电极差分脉冲溶出伏安法测定磺胺嘧啶

采用线性循环溶出伏安法和差分脉冲溶出伏安法对磺胺嘧啶在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在PBS溶液中(pH 7.0),用恒电位法在1.7 V阳极氧化400 s,在B-R缓冲溶液中,磺胺嘧啶在1.02V(vs.Ag/AgCl)处有一良好的氧化峰,在0.02～0.25 V/s范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的不可逆过程。差分脉冲溶出伏安法的氧化峰电流(Ipa)与磺胺嘧啶浓度1×10-6～1×10-4mol/L范围内呈良好的线性关系(r=0.9977),检出限为8.7×10-7mol/L(S/N=3)。方法已用于分析磺胺嘧啶片剂的分析。     

没食子酸在电活化玻碳电极上的电化学行为及测定

采用循环伏安法和线性扫描伏安法对没食子酸在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在pH7.0的磷酸盐缓冲溶液中,用恒电位法在1.7 V电位阳极氧化400 s。然后在pH3.0的柠檬酸盐缓冲溶液中,没食子酸在0.479 V和0.442 V处有一良好的氧化还原峰,在0.02～0.40 V s-1范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的准可逆过程。线性循环伏安法的氧化峰电流与没食子酸浓度1×10-6～1×10-4mol L-1范围内呈良好的线性关系(r=0.980 6),检出限为7.6×10-7mol L-1(S/N=3)。该方法操作简便,重现性较好,并应用此法分析了健民咽喉片剂中的没食子酸的含量。     

Determination of Iodide and Idoxuridine at a Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Modified Glassy Carbon Electrode

The detection limit (about 0.017 μg mL^?1) for voltammetric determination of iodide (peak at +0.87 V vs. Ag/AgCl at pH 2) at a glutaraldehyde‐cross‐linked poly‐L ‐lysine modified glassy carbon electrode involving oxidation to iodine was found to be several orders of magnitude lower than that for the voltammetric determination on a bare glassy carbon electrode. This method was applied successfully to the determination of iodide in two medicinal formulations. Idoxuridine was determined indirectly at the same electrode by accumulating it first at ?0.8 V vs. Ag/AgCl. At this potential the C? I bond in the adsorbed idoxuridine is reduced giving iodide, which is then determined at the modified electrode. The method was successfully applied to the determination of idoxuridine in a urine sample.     

电活化玻碳电极差分脉冲伏安法测定水杨酸的研

采用循环伏安法和差分脉冲伏安法对水杨酸在电活化玻碳电极上的电化学行为进行研究.在pH7.0的PBS溶液中,将玻碳电极用恒电位法在+1.7V电位阳极氧化400 s.在0.2 mol·L- NaOH溶液中,水杨酸在0.602 V处有一良好的氧化峰,其氧化峰电流与扫描速率在0.02～0.2 V·s-1范围内呈良好线性关系,表...     

Highly Sensitive Hydrazine Sensor Based on Co(OH)2 Nanoflakes Electrochemically Deposited on MWCNTs

We delineate the electrochemical preparation of cobalt hydroxide nanoflakes Co(OH)₂ NFs on multi‐walled carbon nanotubes (MWCNTs) by potentiostatic methods. The preparation was done on the surface of glassy carbon electrode (GCE). The prepared nanocomposite was characterized by field emission scanning electron microscopy (FESEM), X‐ray diffraction spectroscopy (XRD) and X‐ray photo electron spectroscopy (XPS). The resulting f‐ MWCNTs/Co(OH)₂ NFs modified GCE exhibits a good electrocatalytic activity for the oxidation of hydrazine in terms of decreasing over potential and increasing peak current. The modified electrode holds good in the linear range from 0.5 to 15.5 μM with limit of detection as 87.5 nM. The sensitivity of our modified electrode is calculated to be 5733 μA/mM cm‐2. Remarkably, the obtained LOD value of our sensor is very lower compared to the recommended concentration of hydrazine in water by World health organization (WHO) and Environmental protective agency (EPA). The modified electrode detects hydrazine selectively even in the presence of common interferants. Various water samples were chosen to study the practical feasibility of our sensor. The sensor also exhibited an appreciable stability, repeatability and reproducibility.     

Determination of s-triazines with copper and glassy carbon electrodes. Flow injection analysis of aziprotryne in water samples

The detection and determination of s-triazines, atrazine-desethyl and aziprotryne by cyclic voltammetry and an amperometric method using a metallic copper electrode and a glassy carbon electrode are described. The concentrations of atrazine-desethyl and aziprotryne in 0.1 M NaOH solutions were determined using the oxidation signal corresponding to the Cu(0)/Cu(I) redox process. The detection level calculated for these s-triazines were 0.3 and 0.5 μg/mL of analyte, respectively. The glassy carbon electrode was shown to give sensitive reduction response to aziprotryne in flow injection mode. No special activation was required for the glassy carbon electrode. A detection limit of 0.2 μg/mL (20 ng aziprotryne) was obtained for a sample loop of 0.1 mL at a fixed potential of –1.0 V (vs. Ag/AgCl) in 0.1 M HCl and a flow rate of ¶3.5 mL/min. Furthermore, the glassy carbon electrode showed stable response in such a system, and the relative standard deviation was only 2.7% using the same surface, and 6.3% using different surfaces. The method developed was applied to the determination of aziprotryne in environmental and tap water samples; using a prior solid-phase extraction step, aziprotryne concentrations lower than 1.0 ng/mL could be measured.     

Determination of s-triazines with copper and glassy carbon electrodes. Flow injection analysis of aziprotryne in water samples

The detection and determination of s-triazines, atrazine-desethyl and aziprotryne by cyclic voltammetry and an amperometric method using a metallic copper electrode and a glassy carbon electrode are described. The concentrations of atrazine-desethyl and aziprotryne in 0.1 M NaOH solutions were determined using the oxidation signal corresponding to the Cu(0)/Cu(I) redox process. The detection level calculated for these s-triazines were 0.3 and 0.5 microg/mL of analyte, respectively. The glassy carbon electrode was shown to give sensitive reduction response to aziprotryne in flow injection mode. No special activation was required for the glassy carbon electrode. A detection limit of 0.2 microg/mL (20 ng aziprotryne) was obtained for a sample loop of 0.1 mL at a fixed potential of -1.0 V (vs. Ag/AgCl) in 0.1 M HCl and a flow rate of 3.5 mL/min. Furthermore, the glassy carbon electrode showed stable response in such a system, and the relative standard deviation was only 2.7% using the same surface, and 6.3% using different surfaces. The method developed was applied to the determination of aziprotryne in environmental and tap water samples; using a prior solid-phase extraction step, aziprotryne concentrations lower than 1.0 ng/mL could be measured.     

Determination of nickel and cobalt in natural waters and biological material by reductive chronopotentiometric stripping analysis in a flow system without sample deoxygenation

The instrumental set-up consists of a thin-layer cell with a glassy carbon working electrode and an inlet valve by means of which six different solutions can be sucked through the cell. The system is controlled by a microprocessor and suction is provided by means of a peristaltic pump. In the first step of the analytical cycle, a mercury film is plated onto the glassy carbon electrode and then the sample solution is allowed into the cell and nickel(II) and cobalt(II) are potentiostatically adsorbed onto the mercury film as their dimethylglyoxime complexes. Nickel(II) and cobalt(II) are then reduced in a medium of 5 M calcium chloride by means of constant current and simultaneously the microprocessor records the potential vs. time behaviour of the working electrode. Finally the mercury film is removed by mild oxidation in an iodine/iodide solution and the glassy carbon surface is cleaned with ethanol and sodium hydroxide prior to the next analytical cycle. The cobalt(II) and nickel(II) concentrations are evaluated by means of a standard addition procedure. The technique was applied to drinking, estuarine and sea water samples. The detection limits on the one sigma level after one minute of potentiostatic adsorption were 9 and 11 ng l^?1 for nickel(II) and cobalt(II), respectively. Nickel(II) and cobalt(II) were determined in reference samples of bovine liver and sea-water sediments after acid digestion. In order to obtain correct cobalt values, it was necessary to reduce cobalt(III) species formed during the acid digestion with sodium tetrahydroborate.     

氢氧化镍薄膜修饰玻碳电极的制备及其对L-赖氨酸氧化的电催化活性

采用恒电位沉积方法将氢氧化镍沉积到玻碳电极表面,得到稳定性高、催化活性好的氢氧化镍薄膜修饰玻碳电极;分析了影响薄膜形成过程的关键因素,确定了最佳薄膜制备方案;与此同时,将薄膜修饰玻碳电极用于生物样品L-赖氨酸的氧化测定,并探讨了其催化作用机理.结果表明,所制备的氢氧化镍薄膜修饰玻碳电极表面发生电化学反应[Ni(OH)2→NiOOH],从而促进电极表面的电子转移,实现对L-赖氨酸的电催化作用.当L-赖氨酸的浓度在1.0×10-4～4.0×10-7 mol/L范围内时,相应氧化峰电流与浓度呈线性关系,检出限达4.0×10-7 mol/L;据此可方便地制备稳定性好且灵敏度高的电流型传感器.     

Initial Stages of Copper Electrocrystallization on a Glassy-Carbon Ring–Disk Electrode from Sulfate Electrolytes of Various Acidity: Potentiostatic Current Transients

Initial stages of copper electrocrystallization on glassy carbon from sulfuric acid electrolytes of pH 0.3 and 3.7 are studied by the method of potentiostatic current transients on rotating and stationary ring–disk electrode. The rate of copper deposition in a 0.5 M Na₂SO₄ + 0.01 CuSO₄ (pH 3.7) solution is marginally higher than in a 0.5 M H₂SO₄ + 0.01 CuSO₄ acid electrolyte (pH 0.3) at the expense of adsorption of sulfate and hydroxide ions on the substrate surface and the copper crystals. Regularities governing the multistage discharge of copper ions, the formation of the new phase nuclei, and the deposit dissolution are analyzed. The results of the study are compared with the data on the kinetics of copper electrocrystallization on a platinum electrode. The acceleration of the copper deposition on glassy carbon in the acid solution of pH 0.3, as compared with platinum, is due to accelerated discharge of copper ions and increased number of univalent copper ions in the near-electrode layer of solution. The oxygen-containing surface groups of glassy carbon (quinone–hydroquinone, carbonyl, etc.) are probably active centers for the discharge of copper ions and three-dimensional nucleation.