氢氟酸刻蚀对Ni/6H-SiC接触性质的作用

采用浓度为10%的氢氟酸（HF）刻蚀6H-SiC单晶片,研究了HF刻蚀时间对Ni/6H-SiC接触性质的影响．经24?h刻蚀的SiC基片在溅射Ni层后,其接触表现良好线性的电流-电压（I-V）曲线．低于这个腐蚀时间的接触具有明显的势垒,但在大于1000℃快速退火后,也得到了良好线性的I-V曲线．X射线衍射（XRD）和俄歇能谱（AES）深度元素分析表明Ni₂Si和C是快速退火后的主要产物．XRD和低能反射电子能量损失谱表明表层的C 关键词： 欧姆接触 SiC 富碳层 互扩散     

基于I-V-T和C-V-T的GaN上Ni/Au肖特基接触特性研究

基于对制作在n-GaN上的肖特基二极管的变温I-V测试和C-V测试，采用表面势垒减薄模型对肖特基二极管的电流输运特性进行了研究.试验结果表明，肖特基接触的电流输运机理非常复杂，在不同的温度条件和偏压条件下有着不同的电流输运机理.在此基础上对肖特基接触I-V特性方程进行了修正，得到了很好的拟合曲线.试验表明，高温I-V法提取的势垒高度与常温C-V法提取的势垒高度接近于根据金属功函数得出的理论势垒高度值. 关键词： 氮化镓 肖特基二极管 表面势垒减薄模型 热电子场发射     

AlGaN/GaN异质结Ni/Au肖特基表面处理及退火研究

采用O₂等离子体及HF溶液对AlGaN/GaN异质结材料进行表面处理后，Ni/Au肖特基接触特性比未处理有了明显改善，反向泄漏电流减小3个数量级.对制备的肖特基接触进行200—600℃ 5min的N₂气氛退火，发现退火冷却后肖特基反向泄漏电流随退火温度增大进一步减小.N₂气中600℃退火后肖特基二极管C-V特性曲线在不同频率下一致性变好，这表明退火中Ni向材料表面扩散减小了表面陷阱密度；C-V特性曲线随退火温度增大向右移动，从二维电子气耗尽电压绝对值减小反映了肖特基势垒的提高. 关键词： AlGaN/GaN 肖特基接触 表面处理 退火     

ZnO纳米线场效应管的制备及I-V特性研究

采用静电探针和原子力探针技术,将化学气相沉积工艺制备的,长度为30—200 μm,直径80—750 nm的单根半导体ZnO纳米线搭接在Au,Zn,Al不同功函的金属隔离沟道两端,构建出了最基本的ZnO纳米线绝缘栅场效应管. 研究了沟道类型、纳米线直径、退火温度和外加栅压对ZnO纳米线场效应管I-V特性的影响. 利用半导体与金属材料的肖特基接触、欧姆接触的产生机理及电子输运理论,对结果进行了分析和讨论. 关键词： ZnO纳米线 场效应管 I-V特性')" href="#">I-V特性     

原子力显微技术研究ZnO纳米棒的压电放电特性

在原子力显微镜的接触扫描模式下,研究了半导体ZnO纳米棒的压电放电特性.采用两步湿化学法制备沿c轴择优生长的ZnO纳米棒阵列;利用镀Pt探针接触扫描ZnO纳米棒获得峰值达120 pA电流脉冲,脉冲持续时间可达30 ms,电流脉冲与纳米棒的形貌存在对应关系.镀Pt探针与ZnO纳米棒接触形成肖特基二极管,I-V特性研究表明放电的ZnO纳米棒压电电势必须大于03 V,以驱动肖特基二极管并输出电流;放电时肖特基二极管的结电阻达吉欧(GΩ)量级,是影响压电电势输出的主要因 关键词： ZnO 纳米棒 压电放电 肖特基接触     

AlGaN/GaN肖特基结参数分析与电流运输机理研究

通过对AlGaN/GaN HEMT器件肖特基栅电流输运机理的研究,在变温下采用I-V法对AlGaN/GaN上的Ni/Au肖特基势垒高度和理想因子进行了计算. 通过对不同电流机理的分立研究,得到了更为准确的势垒高度值_b. 通过分析温度在300—550K之间肖特基反向泄漏电流的特性,得出结论：AlGaN材料的表面漏电不是HEMT器件反向泄漏电流的主要来源. 关键词： AlGaN/GaN异质结 肖特基结 理想因子     

Nd0.67Sr0.33MnOy(y<3.0)中的自旋相关电致电阻效应

用固相反应法制备系列Nd_0.67Sr_0.33MnO_y(y = 3.00—2.80)多晶样品.样品输运性质表现出自旋相关电致电阻特征.对氧含量等于化学计量样品，在测量温度范围内电阻不随负载电流变化，I-V曲线符合线性欧姆定律.对氧含量低于化学计量样品，当高于某一特征温度时，电阻变化符合线性欧姆定律；但低于这一特征温度时，电阻大小与负载电流有关，I-V曲线偏离线 关键词： 钙钛矿结构锰氧化物 电致电阻效应 自旋相关界面输运 氧缺陷     

硼掺杂对四面体非晶碳膜电导性能的影响

以单质硼和高纯石墨的混合粉末压制成型的靶材作为靶源,采用过滤阴极真空电弧技术制备不同硼含量的掺硼四面体非晶碳膜.分别采用四探针法、阻抗分析仪和电化学界面对薄膜的变温电导率、I-V特性和C-V特性进行了测试和研究.实验结果表明,当B含量由0增加至6.04 at%时,薄膜的室温电导率先逐渐增大而后逐渐减小,相应薄膜的电导激活能先逐渐减小而后逐渐增大,并在2.13 at%时分别出现最大和最小值1.42×10^-7S/cm和0.1eV.此外,掺硼四面体非晶碳/n型硅异质结的I-V曲线表现出典型的整流特性,表明p-n结二极管已经形成,且结两端的掺杂能级在空间上连续统一. 关键词： 四面体非晶碳 电导率 I-V曲线')" href="#">I-V曲线 C-V曲线')" href="#">C-V曲线     

Ni/4H-SiC 肖特基势垒磁场下输运性质的分析

采用高真空电子束蒸发的方法将镍 (Ni)淀积在 4H SiC(0 0 0 1)面上 ,制备出良好的Ni/4H SiC肖特基接触 .研究了Ni/4H SiC肖特基势垒在强磁场和低温下的I -V特性 ,并以热电子发射理论为基础 ,结合弛豫近似玻尔兹曼方程对Ni/4H SiC肖特基势垒在磁场下的输运性质进行了分析和计算 ,发现电流的变化与磁场的平方和电压成线性关系 ,和温度成反比关系 ,与实验结果基本符合     

外电场和双轴应变对MoSH/WSi2N4肖特基结势垒的调控

鉴于实验上最新合成的二维半导体材料WSi₂N₄(WSN)和二维金属材料MoSH(MSH),构建了金属-半导体MSH/WSN肖特基结.在实际的金属-半导体接触应用中,肖特基势垒的存在严重降低了器件的性能.因此,获得较小的肖特基势垒甚至是欧姆接触至关重要.本文使用第一性原理计算研究了在外电场和双轴应变作用下MSH/WSN肖特基结势垒的变化.计算结果表明,外电场和双轴应变均可以有效地调控MSH/WSN肖特基结势垒.正向外电场能实现MSH/WSN肖特基结p型与n型肖特基接触之间的动态转化,而负向外电场可实现MSH/WSN肖特基结向欧姆接触的转化.此外,较大的双轴应变可实现MSH/WSN肖特基结p型与n型肖特基接触的相互转化.此项工作为基于WSN半导体的肖特基功能器件及场效应晶体管提供理论指导.     

Ta/Ni/Ta multilayered ohmic contacts on n-type SiC

The interface formation, electrical properties and the surface morphology of multilayered Ta/Ni/Ta/SiC contacts were reported in this study. It was found that the conducting behavior of the contacts so fabricated is much dependent on the metal layer thickness and the subsequent annealing temperature. Auger electron spectroscopy (AES) and X-ray diffraction analyses revealed that Ni₂Si and TaC formed as a result of the annealing. The Ni atoms diffused downward to metal/SiC interface and converted into Ni₂Si layer in adjacent to the SiC substrate. The released carbon atoms reacted with Ta atoms to form TaC layer. Ohmic contacts with specific contact resistivity as low as 3 × 10⁻⁴ Ω cm² have been achieved after thermal annealing. The formation of carbon vacancies at the Ni₂Si/SiC interface, probably created by dissociation of SiC and formation of TaC during thermal annealing, should be responsible for the ohmic formation of the annealed Ta/Ni/Ta contacts. The addition of Ta into the Ni metallization scheme to n-SiC restricted the accumulation of carbon atoms left behind during Ni₂Si formation, improving the electrical and microstructure properties.     

感应耦合等离子体刻蚀p-GaN的表面特性

研究了p-GaN材料经感应耦合等离子体(ICP)刻蚀后的表面特性,并用不同的方法对刻蚀表面进行处理.利用原子力显微镜(AFM)和X射线光电子能谱(XPS)对刻蚀样品进行分析,并在样品表面制作Ni/Au电极,进行欧姆接触特性的测试.实验结果表明了NaOH溶液处理表面对改善材料表面和欧姆接触特性是比较有效的. 关键词： GaN 感应耦合等离子刻蚀 表面处理 欧姆接触     

Electrical properties of the CdTe back contact: A new chemically etching process based on nitric acid/acetic acid mixtures

The performance of the back contact is one of the major issues of CdTe solar cell research. Standard nitric-phosphoric (NP) acid chemical etching before metallization is widely used to improve contact formation. However, previous studies of this traditional etching method indicated a blocking Schottky barrier at the back contact, and a roll-over phenomenon was found in the J-V curves of the CdTe solar cells. In this work, a new etching solution, i.e. a nitric-acetic (NA) acid was employed. The etching rate was slow and a Te-rich layer was formed on the surface, which was less than 1 nm. The CdTe solar cell with this new etching method showed no roll-over phenomenon and displayed a good ohmic back contact performance. XPS analysis demonstrated that the back contact barrier height was close to those of CdTe with standard NP etching. A possible mechanism was presented for the improvement of back contact properties.     

Improved device performance in nonpolar a ‐plane GaN LEDs using a Ni/Al/Ni/Au n‐type ohmic contact

The authors report upon the increased light‐output power (P_out) via a reduction in the forward voltage (V_f) for nonpolar a ‐plane GaN LEDs using Ni/Al/Ni/Au n‐type ohmic contacts. The specific contact resistivity of the Ni/Al/Ni/Au contact is found to be as low as 5.6 × 10^–5 whereas that of a typical Ti/Al/Ni/Au contact is 6.8 × 10^–4 Ω cm², after annealing at 700 °C. The X‐ray photoelectron spectroscopy results show that the upward surface band bending is less pronounced for the Ni/Al contact compared to the Ti/Al contact, leading to a decrease in the effective Schottky barrier height (SBH). The V_f of the nonpolar LEDs decreases by 10% and P_out increases by 15% when the Ni/Al/Ni/Au scheme is used instead of the typical Ti/Al/Ni/Au metal scheme. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Thermal annealing behaviour of Al/Ni/Au multilayer on n-GaN Schottky contacts

Recently GaN-based high electron mobility transistors (HEMTs) have revealed the superior properties of a high breakdown field and high electron saturation velocity. Reduction of the gate leakage current is one of the key issues to be solved for their further improvement. This paper reports that an Al layer as thin as 3 nm was inserted between the conventional Ni/Au Schottky contact and n-GaN epilayers, and the Schottky behaviour of Al/Ni/Au contact was investigated under various annealing conditions by current--voltage (I--V) measurements. A non-linear fitting method was used to extract the contact parameters from the I--V characteristic curves. Experimental results indicate that reduction of the gate leakage current by as much as four orders of magnitude was successfully recorded by thermal annealing. And high quality Schottky contact with a barrier height of 0.875 eV and the lowest reverse-bias leakage current, respectively, can be obtained under 12 min annealing at 450°C in N₂ ambience.     

Origin of ohmic behavior in Ni, Ni2Si and Pd contacts on n-type SiC

Ni, Ni₂Si and Pd contacts were prepared on n-type 4H-SiC and annealed in the temperature range of 750-1150 °C. The annealed contacts were analyzed before and after acid etching, and different features were found in unetched and etched contacts. Carbon left on the SiC surface after the acid etching of Ni₂Si contacts annealed at 960 °C was highly graphitized. In nickel contacts, the graphitization of interface carbon began at 960 °C and increased after annealing at higher temperatures. In palladium contacts, the onset of the interface carbon graphitization was observed after annealing at 1150 °C. For all three types of metallization, the minimal values of contact resistivity were achieved only when the sharp first-order peak at 1585 cm⁻¹ and distinct second-order peak at ∼2700 cm⁻¹ related to the presence of graphitized carbon were detected by Raman spectroscopy after the acid etching of contacts. The properties of unannealed secondary contacts deposited onto etched primary contacts were similar to the properties of the primary contacts unless carbon was selectively etched. The results show that ohmic behavior of Ni-based and Pd contacts on n-type SiC originates from the formation of graphitic carbon at the interface with SiC.     

Characterization of Cr/6H-SiC(0 0 0 1) nano-contacts by current-sensing AFM

The electrical properties and interface chemistry of Cr/6H-SiC(0 0 0 1) contacts have been studied by current-sensing atomic force microscopy (CS-AFM) and X-ray photoelectron spectroscopy (XPS). Cr layers were vapor deposited under ultrahigh vacuum onto both ex situ etched in H₂ and in situ Ar⁺ ion-bombarded samples. The Cr/SiC contacts are electrically non-uniform. Both the measured I-V characteristics and the modeling calculations enabled to estimate changes of the Schottky barrier height caused by Ar⁺ bombardment. Formation of ohmic nano-contacts on Ar⁺-bombarded surfaces was observed.     

Pt interlayer effects on Ni germanosilicide formation and contact properties

Ni and Ni(Pt) germanosilicide formation and their contact properties on n-type epitaxial Si_0.84Ge_0.16 have been studied in this work. It is revealed that compared to NiSi, NiSiGe has enhanced phase stability but worse morphology stability. It is also found that Pt incorporation in germanosilicidation improves the morphology of the germanosilicide film. The Schottky contact characteristics of NiSiGe and Ni(Pt)SiGe on n-SiGe were evaluated by current–voltage (I–V) technique at room temperature. NiSiGe/n-SiGe contact shows a Schottky barrier height (SBH) of 0.65 eV with little difference from that of NiSi/n-Si contact. However, the contact shows a reduced SBH with a markedly increased ideality factor and leakage current when annealing temperature increases to 650 °C, indicating thermal degradation of the contact quality. Pt incorporation increases the SBH to 0.73 eV. In addition, its diode parameters such as SBH, ideality factor, and reverse leakage show better conformity during the whole annealing temperature range (from 450 to 650 °C). Therefore, it is concluded that Pt interlayer between Ni and SiGe can modulate the barrier height of Ni germanosilicide and improve its contact properties.