The in-situ solid-state NMR spectroscopy investigation of alcoholic lactose suspensions

The polymorphic forms of lactose in alcoholic suspensions have been determined by ¹³C CP-MAS NMR spectroscopy, employing hand-made glass inserts. Suspensions of alpha lactose monohydrate (Lα·H₂O) with particle size between 2 and 200 μm were prepared by 24 h reflux or by storage for 28 d in anhydrous ethanol without agitation. These suspensions were compared to an ethanolic sub-micron lactose suspension provided by a 3 M Health Care (Loughborough). The ¹³C CP-MAS NMR spectra indicated that Lα·H₂O dehydrated to stable anhydrous alpha lactose polymorph (Lα_S) whilst suspended in ethanol. In addition, strong ethanol ¹³C resonances were observed for some samples, indicating a liquid–solid interaction between the ethanol and lactose surface. Replacement of ethanol with anhydrous methanol, n-butanol and 3-methylbutan-2-ol implied that the solvent mediated dehydration of Lα·H₂O to Lα_S occurs as a result of sterically controlled interactions.     

High temperature properties of the n = 2 Ruddlesden–Popper phases (La,Sr)3(Fe,Ni)2O7−δ

The crystal chemistry and mixed conductor properties of the n = 2 member of the Ruddlesden–Popper (R–P) phases Sr_3−xLa_xFe_2−yNi_yO_7−δ with 0 ≤ x ≤ 0.3 and 0 ≤ y ≤ 1.0 have been studied at high temperature. High-temperature X-ray diffraction and thermogravimetric measurements of the equilibrium pO₂ (10^− 5 ≤ pO₂ ≤ 1 atm) in the temperature range 400 ≤ T ≤ 1000 °C indicate that the Sr₃FeNiO_7−δ phase is able to accommodate a large oxygen non-stoichiometry (δ ∼ 1.5) without structural transformations. The electrical conductivity and oxygen permeability increase with the substitution of Ni for Fe in the range 550 ≤ T ≤ 1000 °C. The electrical transport of the Sr₃FeNiO_7−δ phase is thermally activated and the activation energy decreases with the substitution of Ni for Fe for a given oxygen content. The increase in the oxygen permeation flux with increasing Ni content is due to an increasing oxygen non-stoichiometry and a lower activation energy for permeation.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Ultrasonic and DFT study of intermolecular association through hydrogen bonding in aqueous solutions of d(−)-arabinose

The experimental measurements of density, viscosity and ultrasonic velocity of aqueous d-arabinose solutions were carried out as functions of concentration (0.1 ≤ m [mol kg^? 1] ≤ 1.0) and temperature (303.15 ≤ T [K] ≤ 323.15). The isentropic compressibility (β_s), acoustic impedance (Z), hydration number (H_n), intermolecular free length (L_f), classical sound absorption (α/f²)_class and shear relaxation time (τ) were calculated by using the measured data. These parameters have been interpreted in terms of solute–solvent interactions. The quantum chemical calculations were performed to study the hydrogen bonding in interacting complex formed between α-D-arabinopyranose in ¹C₄ conformation and water molecules. Computations have been done by using Density Functional Theory (DFT) method at B3LYP/6-31+g(d) level of theory to study the equilibrium structure of α-d-arabinose, α-D-arabinopyranose–water interacting complex and vibrational frequencies. The solution phase study was carried out using Onsager's reaction field model in water solvent. The computed and scaled vibrational frequencies are in good agreement with the main features of the experimental spectrum when seven water molecules are considered explicitly with α-D-arabinopyranose in ¹C₄ conformation. The interaction energy (E_total), hydrogen bond lengths and dipole moment (μ_m) of the interacting complex are also presented and discussed with in the light of solute–solvent interactions.     

Defect equilibria and partial molar properties of (La,Sr)(Co,Fe)O3−δ

The oxygen nonstoichiometry δ of La_1−xSr_xCo_1−yFe_yO_3−δ (x = 0.6 and y = 0.2, 0.4) was investigated by thermogravimetry in the range 703 ≤ T/°C ≤ 903 and 1E−5 < pO₂/atm < 1. The oxygen deficit increases with increasing T and decreasing pO₂. Electronic conductivities σ were measured as a function of pO₂ in the range 1E−5 < pO₂/atm < 1 at 700 ≤ T/°C ≤ 900. At constant T, a p-type pO₂-dependence of σ is observed. Oxygen nonstoichiometry data are analyzed with regard to the enthalpy and entropy of oxidation ΔH_ox^θ and ΔS_ox^θ, as well as to the partial molar enthalpy and entropy of oxygen with respect to the standard state of oxygen (pO₂^θ = 1 atm), (h_O − H_O^θ) and (s_O − S_O^θ), respectively. For 2.67 ≤ (3 − δ) ≤ 2.79, (h_O − H_O^θ) decreases with increasing δ, while (s_O − S_O^θ) is constant within the limits of error. Defect chemical modelling was performed by an ideal solution model under consideration of three different valence states for B-site ions (Co or Fe). The dependence of σ on δ is modelled, using calculated defect concentrations as functions of δ. Deviations from the ideal behaviour suggest an immobilization of n-type charge carriers by oxygen vacancies.     

Synthesis and characterization of La4Ni3−xCoxO10±δ (0.0 ≤ x ≤ 3.0, Δx = 0.2) for solid oxide fuel cell cathodes

The cobalt-doped lanthanum–nickel oxide system, La₄Ni_(3−x)Co_xO_10±δ (0.0 ≤ x ≤ 3.0, Δx = 0.2), was investigated as possible cathode materials for intermediate-temperature solid-oxide fuel cells. X-ray diffraction shows the presence of two structural phases in the series belonging to Bmab for 0.0 ≤ x ≤ 0.2, 0.8 ≤ x ≤ 2.0 and 2.6 ≤ x ≤ 3.0 and Fmmm for 0.4 ≤ x ≤ 0.6 and 2.2 ≤ x ≤ 2.4. All compositions are oxygen-deficient (δ < 0). Electrical conductivity measurements show a systematic decrease in the conductivity as cobalt content increases from x = 0.0 to 2.0, and reverses for x > 2.0. AC impedance measurements of the x = 0.4 composition in symmetrical cells with LSGM as an electrolyte show improved electrode performance over the parent nickelate La₄Ni₃O_9.78. Long-term thermal stability studies show the x = 0.4 composition to be more stable than the x = 3.0 phase after annealing at 1173 K in air for 1 week making this material a viable candidate for cathodes in solid oxide fuel cells.     

Thermodynamics and kinetics of CO and benzene adsorption on Pt(111) studied with pulsed molecular beams and microcalorimetry

The adsorption and desorption of the system CO/Pt(111) and C₆H₆/Pt(111) at 300 K has been investigated with a pulsed molecular beam method in combination with a microcalorimeter. For benzene the sticking probability has been measured in dependence of the coverage θ. For coverages θ > 0.8 transient adsorption is observed. From an analysis of the time-dependence of the molecular beam pulses the rate constant for desorption is determined to be 5.6 s^? 1. With a precursor-mediated kinetic adsorption model this allows to obtain also the hopping rate constant of 95.5 s^? 1. The measured adsorption enthalpies could be best described by (199 ? 77θ ? 51θ²) kJ/mol, in good agreement with the literature values. For CO on Pt(111) also transient adsorption has been observed for θ > 0.95 at 300 K. The kinetic analysis yields rate constants for desorption and hopping of 20 s^?1 and 51 s^?1, respectively. The heats of adsorption show a linear dependence on coverage (131 ? 38θ) kJ/mol between 0 ≤ θ ≤ 0.3, which is consistent with the desorption data from the literature. For higher coverage (up to θ = 0.9ML) a slope of ?63 kJ/mol describes the decrease of the differential heat of adsorption best. This result is only compatible with desorption experiments, if the pre-exponential factor decreases strongly at higher coverage. We found good agreement with recent quantum chemical calculations made for (θ = 0.5ML).     

Effect of viscosity and surface tension on erythrocytes adhesion

Cell–cell adhesion is probably the best cell function to be considered for biophysical modeling from micrometer to the molecular level. The aim of this study is to find a relation between the bulk properties of erythrocytes suspension (like surface tension and viscosity) and erythrocytes adhesion. Our results showed that there is a strong correlation between surface tension and adhesion number (r² = 0.85) and moderate correlation between erythrocytes suspension viscosity and adhesion number (r² = 0.55). Our results were indicated that bulk properties of erythrocytes can affect directly on microscopic properties of erythrocytes.     

Influence of water on the surface structure of 1-hexyl-3-methylimidazolium chloride

The molecular surface structure of an ionic liquid (IL) with and without the presence of water was studied with the surface sensitive technique neutral impact collision ion scattering spectroscopy (NICISS). The IL chosen is 1-hexyl-3-methylimidazolium chloride, which is known to be hydrophilic. Binary mixtures were investigated within the water mole fraction range 0.43 ≤ χ_water ≤ 0.71 at 283 K. During approximately 3 h exposition time in vacuum, we have observed a very low water loss rate from sample. The NICISS measurements suggest that admixture of water to [HMIm]Cl leads to a layered surface structure. Three layers were identified (layer 1 — cations, layer 2 — cations and water, layer 3 — cations, water, and anions). While the first layer is unaffected by water, the thickness of the second layer depends on the water concentration. The thickness of layer 2 is relatively constant for water concentrations χ_water ≤ 0.61, but increases for water contents χ_water ≥ 0.68. The concentration range 0.61 ≤ χ_water ≤ 0.68 seems to play a key role in water network formation.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

Structural and electrochemical characterization of mesoporous thin films of Nb2xV2 − 2xO5 upon lithium intercalation

Nb_2xV_2 ? 2xO₅ (0 ≤ x ≤ 1) powders were prepared by a synthetic route based on the inorganic polymerization of alkoxy-choride precursors and characterized by a combination of X-ray diffraction, ⁵¹V and ⁹³Nb NMR and Raman spectroscopy. Amorphous mesoporous thin films of similar compositions were successfully prepared by a modified Evaporation Induced Self Assembly method using polystyrene-b-polyethyleneoxide diblock copolymer as structuring agent. The electrochemical properties of the mesoporous films upon lithium insertion–deinsertion are investigated by cyclic voltammetry. This study highlights the advantages of such nanoarchitecture in terms of increased capacity to insert lithium.     

Synthesis and electrical properties of nanocrystalline Ca1 − xEuxMnO3 ± δ (0.1 ≤ x ≤ 0.4) powders prepared at low temperature using citrate gel method

Nanopowders of Ca_1 − xEu_xMnO₃ (0.1 ≤ x ≤ 0.4) manganites were synthesized as a single phase using the auto gel-combustion method. The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation or contamination. The Ca_1 − xEu_xMnO₃ system has been synthesized at 800 °C during 18 h, against the conventional method of mixing oxides used to obtain these materials at higher temperatures of synthesis. The formation reaction was monitored by X-ray diffraction (XRD) analysis and an infrared absorption technique (FTIR). The polycrystalline powders are characterised by nanometric particle size, ∼ 48 nm as determined from X-ray line broadening analysis using the Scherrer equation. Morphological analysis of the powders, using the scanning electron microscope (SEM), revealed that all phases are homogeneous and the europium-substituted samples exhibit a significant decrease in the grain size when compared with the undoped samples. The structure refinement by using the Rietveld method indicates that the partial calcium substitution by europium (for x ≥ 0.3) modifies the orthorhombic structure of the CaMnO₃ perovskite towards a monoclinic phase. All manganites show two active IR vibrational modes around 400 and 600 cm^− 1. The high temperature dependence of electrical resistivity (between 25 and 600 °C) allows us to conclude that all the samples exhibit a semiconductor behaviour and the europium causes a decrease in the electrical resistivity by more than one order of magnitude. The results can be well attributed to the Mn⁴⁺/Mn³⁺ ratio.     

High resolution emission spectroscopy of the E2Π–X2Σ+ transition of SrH and SrD

Emission spectra of SrH and SrD have been studied at high resolution using a Fourier transform spectrometer. The molecules have been produced in a high temperature furnace from the reaction of strontium metal vapor with H₂/D₂ in the presence of a slow flow of Ar gas. The spectra observed in the 18 000–19 500 cm^?1 region consist of the 0–0 and 1–1 bands of the E²Π–X²Σ⁺ transition of the two isotopologues. A rotational analysis of these bands has been obtained by combining the present measurements with previously available pure rotation and vibration–rotation measurements for the ground state, and improved spectroscopic constants have been obtained for the E²Π state. The present analysis provides spectroscopic constants for the E²Π state as ΔG(½) = 1166.1011(15) cm^?1, B_e = 3.805503(32) cm^?1, α_e = 0.098880(47) cm^?1, r_e = 2.1083727(89) Å for SrH, and ΔG(½) = 839.1283(23) cm^?1, B_e = 1.918564(15) cm^?1, α_e = 0.034719(23) cm^?1, r_e = 2.1121943(83) Å for SrD.     

Structure,stability and electrical properties of the La(2−x)SrxMnO4±δ solid solution series

Single phase materials of the La_(2−x)Sr_xMnO_4±δ (0.6 ≤ x ≤ 2.0) solid solution series were prepared via solid state reaction. The structure of each material was examined at room temperature and determined to be tetragonal for all phases examined. An expansion in lattice volume was observed on increasing lanthanum content. The stability and thermal expansion of each member of the solid solution series was determined via the use of in situ high temperature X-ray diffraction. It was found that all materials remained stable up to a temperature of 800 °C. Thermal expansion coefficients were found to be in the region of 15 × 10^− 6 K^− 1 for La_(2−x)Sr_xMnO_4±δ compounds where x > 1.4. The electrical conductivity of each phase was also determined over a similar temperature range with a maximum value of ∼6 Scm^− 1 at 900 °C for the x = 1.8 phase.     

Kinetic studies of the electrochemical nitrogen reduction and incorporation into yttria stabilized zirconia

The kinetics of the electrochemical reduction of molecular nitrogen at gold micro electrodes on yttria stabilized zirconia (YSZ) solid oxide electrolyte is studied by steady state polarization measurements. From the η / lg i plot for both cathodic and anodic polarization the apparent transfer coefficients α_a and α_c are evaluated. The sum of α_a + α_c exceeds unity and thus a multistep electron transfer process is suggested. The concept of the stoichiometric number is applied to the electrode reaction N₂ + 6e⁻ = 2N³⁻ supposing that the overall process involves at least two intermediate species. On the basis of the evaluation of the experimental results the reaction N₂⁻ + e⁻ ⇌ N₂²⁻ is suggested as the rate determining reaction step for the cathodic nitrogen reduction and nitride formation.     

Synthesis and photoluminescence properties of YVO4:Eu3+, Al3+ phosphor

The Y_0.95?xAl_xVO₄:5%Eu³⁺ (0≤x≤0.1) phosphors were successfully synthesized by solid state reaction at 900 °C for 6 h, and their luminescence properties were investigated under UV and VUV excitation. Monitoring at 619 nm, a strong broad absorption was enhanced by co-doping of Al³⁺ into the YVO₄:Eu³⁺ lattices at 256 nm under UV excitation. The VUV excitation spectra also showed the enhanced excitation bands at about 156 and 200 nm. Under 254 or 147 nm excitation, it was found that Y_0.95?xAl_xVO₄:Eu³⁺(0≤x≤0.1) phosphors showed strong red emission at about 619 nm corresponding to the electric dipole ⁵D₀^–7F₂ transition of Eu³⁺. The improvement of luminescence intensity of YVO₄:Eu³⁺ was also observed after partial substituting Y³⁺ by Al³⁺ and the optimal luminescence intensity appeared with incorporation of 2.5 mol% Al³⁺.     

Atomic surface diffusion on Pt nanoparticles quantified by high-resolution transmission electron microscopy

Aberration-corrected high-resolution transmission electron microscopy allows for the delocalization-free observation of atomic motions on metallic surfaces and thus enables measurements of the diffusion of single atoms on the surfaces of nanoscopic objects such as nanoparticles. Using this recently introduced method, the diffusion coefficient for surface self-diffusion of Pt nanoparticles is determined through the fluctuating occupation of the particle's atomic columns. This diffusion coefficient is determined to lie in the range D ∼ (10⁻¹⁷ … 10⁻¹⁶) cm²/s.     

Preparation,characterization and electrical property of Mn-doped ceria-based oxides

Manganese-doped ceria-based oxides, Ce_1−xMn_xO_2−δ (0.05 ≤ x ≤ 0.3) and Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x≤ 0.2, 0.05 ≤ y ≤ 0.25) were synthesized, and crystal phase analysis by XRD and measurements of electrical properties were performed. Solubility limit of Mn in Ce_1−xMn_xO_2−δ˙ seemed to be between 5 mol% and 10 mol% and Mn₃O₄ was the main by-product above the solubility limit in the case of heat treatment at 1300 °C. Judging from the oxygen partial pressure dependence of total conductivity and emf measurements, Ce_1−xMn_xO_2−δ˙ is a single-phase mixed conductor within the composition below the solubility limit, and when the composition of Mn exceeds the solubility limit, it becomes the dual-phase mixed conductor of Ce_1−xMn_xO_2−δ˙ and Mn₃O₄. The doing of Mn in gadlia-doped ceria, Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x ≤ 0.2, 0.05 ≤ y ≤ 0.25), was more difficult than that in CeO₂ presumably due to the preferential reaction between Gd and Mn to give GdMnO₃ to the GDC solid solution formation, and the Mn doping seems not to be so effective in preparing the mixed ionic–electronic conductor based on GDC.     

The studies on structural and thermal properties of delithiated LixNi1/3Co1/3Mn1/3O2 (0 < x ≤ 1) as a cathode material in lithium ion batteries

The structural and thermal properties of the delithiated Li_xNi_1/3Co_1/3Mn_1/3O₂ (0 < x ≤ 1) material have been investigated by using diffraction and thermoanalytical techniques such as XRD and TG-DSC methods. XRD result shows that the delithiated materials maintain the O3-type structure with defined stoichiometric number at the range of 0.24 < x ≤ 1, exhibiting good crystal structural stability. The cobalt and nickel ions in the delithiated materials change their valence state (i.e. Co³⁺ to Co⁴⁺ and Ni³⁺ to Ni⁴⁺) when x < 0.49; the irreversible changes of the transformation may affect the first cycle of charge–discharge efficiency of the materials. A comparison of the results of TG-DSC with TPD-MS shows that the irreversible change of oxygen species during the delithiation process of Li_xNi_1/3Co_1/3Mn_1/3O₂ have great influence on the structural and thermal stability and reversibility of the materials.