Phase separation of gas–liquid and liquid–liquid microflows in microchips

Phase separation of gas–liquid and liquid–liquid microflows in microchannels were examined and characterized by interfacial pressure balance. We considered the conditions of the phase separation, where the phase separation requires a single phase flow in each output of the microchannel. As the interfacial pressure, we considered the pressure difference between the two phases due to pressure loss in each phase and the Laplace pressure generated by the interfacial tension at the interface between the separated phases. When the pressure difference between the two phases is balanced by the Laplace pressure, the contact line between the two phases is static. Since the contact angle characterizing the Laplace pressure is restricted to values between the advancing and receding contact angles, the Laplace pressure has a limit. When the pressure difference between the two phases exceeds the limiting Laplace pressure, one of the phases leaks into the output channel of the other phase, and the phase separation fails. In order to experimentally verify this physical picture, microchips were used having a width of 215 μm and a depth of 34 μm for the liquid–liquid microflows, a width of 100 μm and a depth of 45 μm for the gas–liquid microflows. The experimental results of the liquid–liquid microflows agreed well with the model whilst that of the gas–liquid microflows did not agree with the model because of the compressive properties of the gas phase and evaporation of the liquid phase. The model is useful for general liquid–liquid microflows in continuous flow chemical processing.     

Kinetic characteristics of gas–liquid ozone reactions

An experimental chemical method for determining the kinetic characteristics (volumetric mass transfer coefficient and rate constant of a second-order reaction) of gas–liquid ozone reactions in a bubble column reactor is described. The calculation formulas are substantiated, and the ranges of values of the experimental factors that determine the method’s limits of applicability are found. The conditions under which the boundary-value problem of a gas–liquid ozone reaction of the second order can be reduced to a problem of a pseudo-first order reaction allowing an analytical solution are revealed.     

Direct and indirect photoinduced gas–liquid phase transitions

The condensation of supersaturated vapors of various substances in air under UV irradiation in a cloud chamber has been studied. The irradiation and subsequent photodissociation greatly facilitate the condensation of vapors in comparison with unirradiated mixtures, wherein both a vapor that directly absorbs radiation (direct photoinduced phase transition) and, for example, water vapor in the presence of photodissociating impurities (indirect photoinduced transition) can be condensed.     

Hydrodynamic studies on inverse gas—liquid—solid fluidization

Downward (inverse) fluidization can be achieved when the density of the particles is less than that of the liquid and the liquid is the continuous phase. This technique is mainly used in biochemical engineering operations, e.g. for fermentation and waste water treatment. Experiments were conducted to study the hydrodynamics of inverse gas—liquid—solid fluidized beds using very light particles. The experimental data for the minimum liquid velocity at the onset of fluidization are correlated in terms of the physical properties of the fluids, particle characteristics and system variables. A correlation for the friction factor is also proposed.     

Adsorption of cationic multicharged surfactants at liquid–gas interface

We present the review of the existing methods for describing adsorption at fluid interfaces that may be applicable for multiple charge cationic surfactant structures of various architectures—multiheaded (e.g., dicephalic) structures and multimeric surfactants (e.g., dimeric (so-called gemini), trimeric, tetrameric, etc.). We discuss the role of the prefactor the in the Gibbs adsorption equation originating from the number of charges present in the adsorbed layer and the reasons for the deviation from its thermodynamic value. We present several models of adsorption that can be used to describe surface tension isotherms and appreciate the role of prof. Peter Kralchevski in their development. Application of molecular dynamics methods combined with the approach based on the thermodynamic models of multicharged surfactant adsorption may lead to an explanation of some experimentally observed phenomena and can provide the basis for the development of novel materials designated for a variety of applications.     

New innovations in ionic liquid–based miniaturised amperometric gas sensors

Gas detection is an essential part of everyday life; for some applications, using sensors for toxic and hazardous gases can literally mean the difference between life and death. In this minireview, recent progress in amperometric gas sensing using miniaturised electrodes and devices is described. The focus is on the use of nonvolatile room-temperature ionic liquids (RTILs) as electrolytes, which possess inherent advantages such as wide electrochemical windows, high thermal and chemical stability, intrinsic conductivity and good solvating properties. Various different gases, electrodes and RTILs have been investigated in the strive towards new materials for improved gas sensors. The most recent developments using porous membrane electrodes, planar devices (e.g. screen-printed, thin-film, microarray and interdigitated electrodes) and the modification of these surfaces for improved sensitivity are described. RTILs have great potential to be used as electrolytes in amperometric gas sensors, with improved lifespan of the sensor in hot/dry environments and allowing miniaturisation of devices. However, it is clear that more understanding of their long-term operation and utility in real environments (e.g. background air, varying temperatures and humidity levels) is needed before their realisation in successful commercial devices.     

Determination of pesticide residues in red wines with microporous membrane liquid–liquid extraction and gas chromatography

A sample pretreatment method based on microporous membrane liquid-liquid extraction (MMLLE) was developed for the subsequent gas chromatographic determination of pesticides in wine. MMLLE provided efficient and selective extraction with enrichment factors in the range 3-13. The gas chromatographic separation was carried out using on-column injection and flame ionization detection. The method was linear, repeatable and sensitive. The limits of quantification were better than 0.006 mg/L for all the analytes except for iprodione (0.37 mg/L). The method was applied to the determination of pesticides in several red wines of different origin.     

A new concept of hollow fiber liquid–liquid–liquid microextraction compatible with gas chromatography based on two immiscible organic solvents

A new concept of liquid–liquid–liquid microextraction (LLLME) was introduced based on applying two immiscible organic solvents in lumen and wall pores of hollow fiber (HF). With this methodology, analytes of interest can be extracted from aqueous sample, into a thin layer of organic solvent (dodecane) sustained in the pores of a porous hollow fiber, and further into a μL volume of organic acceptor (acetonitrile or methanol) located inside the lumen of the hollow fiber. Some chlorophenols (CPs) were selected as model compounds for developing and evaluating of the method performance. The analysis was performed by gas chromatography–electron capture detection (GC–ECD) without derivatization. The factors affecting the HF-LLLME of target compounds were investigated and the optimal extraction conditions were established. Under the optimum conditions, preconcentration factors in a range of 208–895 were obtained. The performance of the proposed method was studied in terms of linear dynamic ranges (LDRs from 0.02 to 100 ng mL⁻¹), linearity (R² ≥ 0.995), precision (RSD % ≤ 8.1) and limits of detection (LODs in the range of 0.006–0.2 ng mL⁻¹). In addition to preconcentration, HF-LLLME also served as a technique for sample clean-up.     

Bubble break-up in gas—liquid bioreactors: Break-up in turbulent flows

The breakage of gas bubbles in a turbulent flow field is explored. Break-up was found to occur by a dumbbell elongation of the bubble. The elongational     

Tilting operator for phospholipidic molecular domains at the liquid–gas interface

We derive a coordinate independent operator expression for the tilting operator of molecular domains at the liquid–gas interface. The domains are made up of phospholipidic molecules modeled as spherocylinders. The molecules of the domain are oriented parallel to each other. The centers of symmetry of the molecules form a lattice. The tilting operator keeps track of the deformations suffered by this lattice as the domain molecules are tilted relative to the normal to the interface. The results obtained are important for dynamic calculations of inclination dependent collective film characteristics, as in the simulation of surface density versus surface pressure curves in a Langmuir film. The tilting operation can be decomposed into three separate simple operations: a global rotation, a local oblique realignment, and a global vertical translation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of hormones in milk by hollow fiber-based stirring extraction bar liquid–liquid microextraction gas chromatography mass spectrometry

The hollow fiber-based stirring extraction bar liquid–liquid microextraction was applied to the extraction of hormones, including 17-α-ethinylestradiol, 17-α-estradiol, estriol, 17-β-estradiol, estrone, 17-α-hydroxyprogesterone, medroxyprogesterone, progesterone and norethisterone acetate, in milk. The present method has the advantages of both hollow fiber-liquid phase microextraction and stirring bar sorptive extraction. The stirring extraction bar was used as both the stirring bar of microextraction, and extractor of the analytes, which can make extraction, clean-up and concentration be carried out in one step. When the extraction was completed, the stirring extraction bar was easy isolated from the extraction system with the magnet. Several experimental parameters, including the type of extraction solvent, the number of hollow stirring extraction bar, extraction time, stirring speed, ionic strength, and desorption conditions were investigated and optimized. The analytes in the extract were derived and determined by gas chromatography mass spectrometry. Under optimal experimental conditions, good linearity was observed in the range of 0.20–20.00 ng mL⁻¹. The limits of detection and quantification were in the range of 0.02–0.06 ng mL⁻¹ and 0.07–0.19 ng mL⁻¹, respectively. The present method was applied to the analysis of milk samples, and the recoveries of analytes were in the range of 93.6–104.6% with the relative standard deviations ranging from 1.6% to 6.2% (n = 5). The results showed that the present method was a rapid and feasible method for the determination of hormones in milk samples.     

Mathematical modeling of gas–liquid membrane contactors using random distribution of fibers

This work presents a mathematical model for gas absorption in microporous hollow fiber membrane contactors by using a random distribution of fibers. The chemical absorption of carbon dioxide into aqueous amine solutions and sulfur dioxide into water were simulated by this model. The nonlinear mathematical expressions of the component material balance for the liquid, membrane, and gas were solved simultaneously by using a numerical method. The results from the model were compared with four sets of different experimental data in the literature. In addition, the contactors were modeled based on the assumption of regular arrangement of fibers in the shell side by using Happel's free surface as well as plug flow models. The plug flow model was employed to compare the various available equations in the literature for the shell side mass transfer coefficient. The results indicate that the channeling of gas in the shell side decreases the efficiency of contactor significantly. It was found that the random distribution of fibers is a suitable method to simulate the commercial modules. The results also indicate that, the regular Happel's free surface model and the plug flow model are more suitable for handmade modules. The influence of shell side channeling on the contactor performance were investigated in different fiber packing densities, and in various gas and liquid flow rates.     

Rapid automatic nucleic acid purification system based on gas–liquid immiscible phase

The continuous expansion of nucleic acid detection applications has resulted in constant developments in rapid, low-consumption, and highly automated nucleic acid extraction methods. Nucleic acid extraction using magnetic beads across an immiscible phase interface offers significant simplification and parallelization potential. The gas–liquid immiscible phase valve eliminates the requirement for complicated cassettes and is suitable for automation applications. By analyzing the process of magnetic beads crossing the gas-liquid interface, we utilized a low magnetic field strength to drive large magnetic bead packages to cross the gas-liquid interface, providing a solution of high magnetic bead recovery rate for solid-phase extraction with a low-surfactant system based on gas-liquid immiscible phase valve. The recovery rate of magnetic beads was further improved to 90%–95% and the carryover of the reagents was below 1%. Consequently, a chip and an automatic system were developed to verify the applicability of this method for nucleic acid extraction. The Hepatitis B virus serum standard was used for the extraction test. The extraction of four samples was performed within 7 minutes, with nucleic acid recovery maintained above 80% and good purity. Thus, through analysis and experiments, a fast, highly automated, and low-consumption nucleic acid recovery method was proposed in this study.     

Analysis of captan, folpet, and captafol in apples by dispersive liquid–liquid microextraction combined with gas chromatography

A novel method was developed for the determination of captan, folpet, and captafol in apples by dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD). Some experimental parameters that influence the extraction efficiency, such as the type and volume of the disperser solvents and extraction solvents, extraction time, and addition of salt, were studied and optimized to obtain the best extraction results. Under the optimum conditions, high enrichment factors for the compounds were achieved ranging from 824 to 912. The recoveries of fungicides in apples at spiking levels of 20.0 μg kg⁻¹ and 70.0 μg kg⁻¹ were 93.0–109.5% and 95.4–107.7%, respectively. The relative standard deviations (RSDs) for the apple samples at 30.0 μg kg⁻¹ of each fungicide were in the range from 3.8 to 4.9%. The limits of detection were between 3.0 and 8.0 μg kg⁻¹. The linearity of the method ranged from 10 to 100 μg kg⁻¹ for the three fungicides, with correlation coefficients (r ²) varying from 0.9982 to 0.9997. The obtained results show that the DLLME combined with GC–ECD can satisfy the requirements for the determination of fungicides in apple samples. Figure Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD) allows satisfactory determination of fungicides in apple samples     

Determination of organochlorine pesticides in river water using dispersive liquid–liquid microextraction and gas chromatography–electron capture detection

Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD), has been developed for the extraction and determination of 14 organochlorine pesticides (hexachlorocyclohexanes (α-HCH, β-HCH and δ-HCH), Lindane (γ-HCH), Aldrin, Dieldrin, Endrin, Heptachlor, Heptachlor epoxide, α-Chlordane, β-Chlordane and p,p′-DDT, p,p′-DDD, p,p′-DDE) in river water samples. Factors relevant to the microextraction efficiency, such as the kind of extraction and disperser solvent, their volume and the salt effect was investigated and optimised. In this method the appropriate mixture of extraction solvent (13.5 µL carbon disulphide) and disperser solvent (0.50 mL acetone) were rapidly injected into the aqueous sample by syringe. The values of the detection limit of the method were in the range of 0.05–0.001 µg L^?1, while the relative standard deviations for five replicates varied from 2.7 to 9.3%. A good linearity (0.9894 ≤ r ² ≤ 0.9998) and a broad linear range (0.01–200 µg L^?1) were obtained. The method exhibited enrichment factors ranging from 647 to 923, at room temperature. The relative standard deviations varied from 2.7 to 9.3% (n = 5). The relative recoveries of each pesticide from water samples at spiking levels of 2.00 and 10.0 µg L^?1 were 88.0–111.0% and 95.8–104.1%, respectively. Finally, the proposed method was successfully utilised for the preconcentration and determination of the organochlorine pesticides in the Jajrood River water samples.     

On-line coupling of microporous membrane liquid–liquid extraction and gas chromatography in the analysis of organic pollutants in water

A method for the determination of hydrophobic pollutants in surface waters was developed. The pretreatment was done with microporous membrane liquid–liquid extraction, the extract was eluted to a sample loop in the large-volume injector valve of the gas chromatograph and the extract was injected on-line to the gas chromatograph. The method was optimised using standard compounds and the linearity, the limits of detection and quantification of the method were studied. The method allowed the determination of hydrophobic pesticides and PAHs at the ng L^–1 level. The RSD values for the repeatability of the method varied from 4.2% to 25.6%, being on average 9.5%. Surface water samples from Finnish lakes and rivers were analysed.     

Determination of 2-ethylhexyl 4-(dimethylamino) benzoate using membrane-assisted liquid–liquid extraction and gas chromatography-mass spectrometric detection

A flow-cell for micro-porous membrane liquid–liquid extraction with a sheet membrane was used to extract 2-ethylhexyl 4-(dimethylamino) benzoate (EDB) from urine of solar-cream users and spiked wine samples. The cell enabled the target analyte to be extracted from 7.9 mL of donor solution into 200 μL of acceptor solution (decane). After extraction, the acceptor solution was transferred to a micro-vial for GC-MS analysis without derivation. In this work, variables affecting the enrichment factor were also studied, such as organic solvent, extraction time, recirculation flow of the donor solution through the donor chamber, presence of potassium chloride and ethanol in the donor solution and pH. The method has been evaluated in terms of linearity, sensitivity, precision, limits of detection and quantification and extraction efficiency. Limits of quantification were 1 and 3 μg L⁻¹ EDB for urine and wine, respectively. Quantitative analysis has been carried out by applying the method of standard additions. Within- and between-day relative standard deviations were lower than 12% and 20%, respectively. EDB was found in the urine of users of cream containing EDB in the concentration interval 1.2–7.2 μg L⁻¹. Therefore, this provides evidence of EDB dermal absorption and subsequent excretion through the urinary tract. EDB was not found in the analysed wine samples.