Delamination of organic coating on carbon steel studied by scanning Kelvin probe force microscopy

Corrosion‐induced delamination of an epoxy coating on the AISI/SAE 1045 carbon steel was studied under a humid atmospheric condition (temperature of 25 °C, 1 standard atmospheric pressure, relative humidity of 90%) by the technique of scanning Kelvin probe force microscopy (SKPFM). Surface‐polished 1045 samples were first cold‐coated with the epoxy and then subject to the atmospheric corrosion under the specified condition. At predetermined time intervals, surface Volta potential differences of the samples were measured using the SKPFM over the dry surface of epoxy coating. The map of Volta potential differences demonstrated high contrasts among three characteristic zones: intact steel‐epoxy interface, delaminated interface, and interface with active corrosion, which was then linked to the actual corrosion potential of the steel (measured using a potentiostat with respect to a saturated calomel electrode) based on a rigorous calibration procedure. It was found that the SKPFM was able to provide direct and nondestructive detection of early active corrosion and coating delamination on steels at a submicroscopic resolution, which outperformed the conventional electrochemical techniques for the same purposes. Copyright © 2012 John Wiley & Sons, Ltd.     

Compression-inhibited pore formation of polyelectrolyte multilayers containing weak polyanions: a scanning force microscopy study.

Morphological changes of poly(acrylic acid)/poly(diallyldimethylammonium chloride) multilayers induced by low pH were investigated by scanning force microscopy. The weakened interaction between the charged polymer chains in the protonation process is believed to be the reason for this variation. Kinetic studies have shown that during protonation phase separation and dissociation of the multilayers took place successively. The compression of the multilayers, however, caused a transition of the multilayers from a rubbery state to a glassy state. As a result, the closely compacted multilayers lost their sensitivity to pH change. An increase of electrostatic and hydrophobic interactions, can decrease the free energy of the multilayers, and stabilize the films. By compression of the multilayers with a rubber stamp having geometric patterns, films with spatially localized pores were produced.     

Friction force microscopy of self-assembled monolayers: probing molecular organisation at the nanometre scale

The basic principles behind friction force microscopy are described. Applications of friction force microscopy to self-assembled monolayers are reviewed. Work in the author’s laboratory on the frictional properties of self-assembled monolayers is described, and the findings applied in the characterisation of a much more complex material, plasma-treated polyester. Friction force microscopy is found to be a powerful tool for the analysis of the chemical composition and molecular organisation of molecular materials at the nanometre scale.     

Scanning force microscopy based rapid force curve acquisition on supported lipid bilayers: experiments and simulations using pulsed force mode.

In situ pulsed force mode scanning force microscopy (PFM-SFM) images of phase separated solid-supported lipid bilayers are discussed with the help of computer simulations. Simultaneous imaging of material properties and topography in a liquid environment by means of PFM-SFM is severely hampered by hydrodynamic damping of the cantilever. Stiffness and adhesion images of solid-supported membranes consisting of cholesterol, sphingomyelin, and 1,2-dioleyl-phosphatidylcholine obtained in aqueous solution exhibit contrast inversion of adhesion and stiff. ness images depending on parameters such as driving frequency, amplitude, and trigger setting. Simulations using a simple harmonic oscillator model explain experimental findings and give a deeper insight into the way PFM-SFM experiments have to be performed in order to obtain interpretable results and hence pave the way for reliable material contrast imaging at high speed.     

Ru(TAP)3]2+-photosensitized DNA cleavage studied by atomic force microscopy and gel electrophoresis: a comparative study

Topological modifications of plasmid DNA adsorbed on a variety of surfaces were investigated by using atomic force microscopy (AFM). On mica modified with 3-aminopropyltriethoxysilane (APS) or poly-L-lysine, the interaction between the plasmid DNA and the surface "freezes" the plasmid DNA conformation deposited from solution, and the AFM images resemble the projection of the three-dimensional conformation of the plasmid DNA in solution. Modified mica with low concentrations of Mg(2+) leads to a decrease in the interaction strength between plasmid DNA and the substrate, and the AFM images reflect the relaxed or equilibrium conformation of the adsorbed plasmid DNA. Under these optimized deposition conditions, topological modifications of plasmid DNA were produced under irradiation in the presence of [Ru(TAP)(3)](2+) (TAP = 1,4,5,8-tetraazaphenanthrene), which is a non-intercalating complex, and were followed as a function of illumination time. The observed structural changes correlate well with the conversion of the supercoiled covalently closed circular form (ccc form) into the open circular form (oc form), induced by a single-strand photocleavage. The AFM results obtained after fine-tuning of the plasmid DNA-substrate interaction compare well with those observed from gel electrophoresis, indicating that under the appropriate deposition conditions, AFM is a reliable technique to investigate irradiation-induced topological changes in plasmid DNA.     

Metal‐conducting polymer interface studied by Kelvin probe microscopy: Au and Al on poly(3‐octyl‐thiophene)

In this work, we report a Kelvin probe microscopy investigation on the structural and electronic properties of gold and aluminum thin films evaporated on poly(3‐octyl‐thiophene) films. Our experimental setup allows us to perform scanning force microscopy (SFM) studies of the same area even if the sample is taken out of the SFM system for different processes (Au and Al evaporation). This allows a detailed study of the effect of adsorbed metal particles on the morphology and electrical properties of polymer thin films at the nanoscale. We found different behavior for both metals in morphology and electrical properties at the interface. These results can contribute to explain what happens at the metal–polymer interface of the devices when the metal contacts are grown. Thereby the observed nanoscale structural changes can be correlated with the overall performance of the fabricated devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1083–1093     

Application of work function measurements to the characterization of thin films and solid surfaces

Two different methods of electron work function measurements, the diode and the onset method, which can easily be incorporated in existing analytical equipment are described. For the diode method the sample is used as the anode of a diode arrangement, and the work function changes of the specimen are obtained from the shift of the break points of characteristic retarding field lines. The onset method uses the shift of the onset of the secondary electron energy distribution due to work function changes.Both methods were applied to Ta₂O₅ layers of 500 Å thickness which were produced by electrochemical oxidation of polycrystalline tantalum substrates. In particular, bombardment induced work function changes during sputter removal of these layers have been investigated.The onset method was also applied to differently oriented grains of a polycrystalline Ta specimen. Work function differences of 0.1 eV between two different grain surfaces were safely detectable.In addition, a work function difference of 0.5 eV between Au and Mo was determined which agrees well with literature values.     

Imaging surfaces of nano‐scale roughness by atomic force microscopy with carbon nanotubes as tips: a comparative study

Accurate knowledge of the nanoroughness of surfaces is crucial for many applications related to optics, electronics or tribology. Although atomic force microscopy (AFM) can image surfaces with a nanometre spatial resolution, the finite size of standard tips means that pores, pits or grooves with dimensions similar to or smaller than the tip apex will not be accurately imaged. Furthermore, standard tips are made of silicon or silicon nitride and are prone to wear. Mitigation may arise from the availability of AFM tips with a carbon nanotube (CNT) at their foremost end. This study compares the imaging performance of ultrasharp Si tips, CNT AFM tips prepared by a Langmuir‐Blodgett (LB) technique, and of CNT AFM tips prepared by a chemical vapour deposition (CVD) technique. The free length of the CNT AFM tips is in the range 80–200 and 600–750 nm, respectively. A polycrystalline niobium film surface is imaged that shows nanoroughness. The measurements demonstrate that CNT AFM tips allow excellent imaging if the scan parameters are adjusted very carefully. Nevertheless, in some cases distortions are found. The measured average grain diameter is 19.9 ± 3.6 nm in the case of a CNT AFM tip made by the LB technique, and 18.0 ± 3.3 nm in the case of a CNT AFM tip made by CVD. In addition to cross‐sections of topography images, also the power spectral density (PSD) is analyzed. An empirical approach for the readout of the characteristic length is suggested that involves the first derivative of the decadic logarithm of the PSD. Copyright © 2011 John Wiley & Sons, Ltd.     

An atomic force microscopy study of asphaltenes on mica surfaces. Influence of added resins and demulsifiers

 Monolayers of asphaltene and resins on the water surface have been transferred at a surface pressure of 10 mN/m onto mica substrates using the Langmuir–Blodgett technique. Atomic force microscopy (AFM) has been used to examine the topography of these layers. Monolayers consisting of pure asphaltene fractions provide a rigid film with a close-packed structure, while the resins build up a continuous open network. Mixed films of these two fractions show that a gradual increase in resin concentration leads to an opening of the rigid asphaltene structure towards a more resin like configuration. Increased aggregation when the two heavy functions are present in one film is seen as larger individual units in the AFM pictures. Addition of high-molecular-weight demulsifiers/inhibitors results in the same kind of influence on the asphaltene film as seen with the resins. Received: 30 April 1999 Accepted: 29 November 1999     

A combined TEM and SKPFM investigation of the surface layers on rolled AA5050 aluminium alloy using ultra‐microtomy

This article studies the evolution of near‐surface morphology as a function of various thermo‐mechanical treatments along the fabrication line of rolled AA5050 aluminium alloy. Ultra‐microtomy has been used to prepare cross‐sectional thin foils for transmission electron microscopy (TEM) and proper surfaces for scanning Kelvin probe force microscopy (SKPFM) analysis. A slight increase in the Volta potential difference (between the inter‐metallics and the matrix) between the as‐cast surface and the surface obtained after the first hot‐mill pass, emphasized that the changes in surface micro‐structure, which in turn affect the corrosion and electrochemical properties of the finished product, had already occurred at that stage. The Volta potential difference during the subsequent hot‐mill pass remained relatively constant. As far as the near‐surface morphology was concerned, hot‐rolling resulted in the formation of a heavily deformed surface layer. Annealing of the hot‐rolled aluminium sheet resulted in partial re‐crystallization of the surface layer. Subsequent cold‐rolling re‐introduced deformation in the near‐surface region. Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of single-wall carbon nanotubes on Langmuir–Blodgett films of ferroelectric liquid crystals as studied by atomic force microscopy

Langmuir–Blodgett films of ferroelectric liquid crystal (LC) doped with low concentration of single-wall carbon nanotubes have been prepared and characterised. Pressure–area isotherms show that the films are stable and have good spreading properties. The interaction between nanotubes and LC molecules in the monolayer was increased during barrier compression, resulting in increased surface pressure. We observed phase change with increasing nanotube concentration in ferroelectric LC matrix. Atomic force microscopy profiles indicate uniform deposition of material on single crystal silicon wafer.     

Beyond the Planck–Benzinger thermal work function: New insights into the role of molecular switches in biology

The Planck‐Benzinger methodology provides a means of determining the innate temperature‐invariant enthalpy, ΔH°(T₀), thermal agitation energy, or the heat capacity integrals ∫ΔCp°(T)dT, and allows precise determination of 〈T_Cp〉, 〈T_h〉, 〈T_s〉, and 〈T_m〉. It is a method for evaluating [ΔH ? ΔH°(T₀)], the heat of reaction for biologic molecules at room temperature, and provides for a better understanding of cooperative thermodynamic compensation. The Planck‐Benzinger methodology demonstrates that macromolecular interactions will always exhibit a negative value of the Gibbs free energy change at a well‐defined temperature. It can be used for determination of the thermodynamic molecular switch, where there is a change of sign in ΔCp°(T)_reaction which determines the behavior patterns of the Gibbs free energy change. All interacting biologic systems that we have thus far examined using the Planck‐Benzinger approach point to the universality of this thermodynamic switch. © 2002 Wiley Periodicals, Inc. Int J Quantum Chem, 2002     

Latex film formation studied with the atomic force microscope: Influence of aging and annealing

The surface structure of latex dispersion films was examined with an atomic force microscope. All measurements were done in air on latex films having a minimum film formation temperature of 12°C and a glass transition temperature of 18°C. One aim of this study was to follow structural changes during film formation. Three minutes after spreading the film, its surface layer dried. Afterwards, the structure of the film did not change anymore. Only after 4 months could structural changes be observed: Though individual latex particles could be identified, the particles partly melted into one another.After annealing films at 50° or 60°C for 4 h, the latex particles partly melted into one another, but individual particles could still be identified. When annealing at or above 80°C, no individual latex particles were visible anymore. With increasing temperature the film roughness decreased from 3 nm without annealing to 0.8 nm at 100°C annealing temperature. In addition, islands of 2–4 nm thickness appeared on the film surface. These islands could be scraped off the film by increasing the force between tip and sample, indicating that they are composed of surfactant which was squeezed out of the film.     

Shear banding in strained semicrystalline polyamide 6 films as revealed by atomic force microscopy: Role of the amorphous phase

Atomic force microscopy (AFM) has been used to visualize the plastic deformation mechanisms that are responsible for the yielding of semicrystalline polymers of low degree of crystallinity (<50%). Indeed, AFM, if operated in suitable conditions, is able to image both the amorphous and the crystalline phases. Polyamide 6 films have been drawn at temperatures T < 160 °C. Postmortem AFM observations show that, at yield, shear bands nucleate and propagate in the amorphous phase. They cross the crystalline lamellae and run over the whole surface of the sample. By crossing the lamellae, they form nanoblocks of uniform size. Neither the size of the nanoblocks nor the angle between the tensile axis and the shear bands can be explained in terms of crystal plasticity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 687–701, 2004     

原子力显微镜研究高分子超薄膜结晶机理及功能化调控

近十年来,随着功能高分子单晶(含单层或寡层片晶)工程及应用研究的不断深入,除了纳米尺度结晶形貌的表征以外,多功能原子力显微镜还被用于研究分子结构、结晶条件和后处理条件对功能高分子晶体性能(电、热、光、磁等)的影响,进一步还可采用扫描探针加工技术(机械刻蚀、电致刻蚀和热致刻蚀等)对其性能进行调控以构筑功能化聚集态结构和微图案.另一方面,超薄膜中单层或寡层片晶可为研究高分子结晶提供合适的模型体系,与原子力显微镜相结合,不但可以原位、实空间、高分辨地研究高分子的成核与生长过程(生长形态演变和生长动力学),还可以用于研究亚稳态折叠链片晶厚度和形态随热处理温度与时间的演化,从而加深对片晶内有序差异、片晶增厚与熔融行为和自诱导成核的认识.     

Label-free detection of the aptamer binding on protein patterns using Kelvin probe force microscopy (KPFM)

Anti-lysozyme aptamers are found to preferentially bind to the edge of a tightly packed lysozyme pattern. Such edge-binding is due to the better accessibility and flexibility of the edge lysozyme molecules. Kelvin probe force microscopy (KPFM) was used to study the aptamer–lysozyme binding. Our results show that KPFM is capable of detecting the aptamer–protein binding down to the 30 nm scale. The surface potential of the aptamer–lysozyme complex is approximately 12 mV lower than that of the lysozyme. The surface potential images of the aptamer-bound lysozyme patterns have the characteristic shoulder steps around the pattern edge, which is much wider than that of a clean lysozyme pattern. These results demonstrate the potentials of KPFM as a label-free method for the detection of protein–DNA interactions. Figure Aptamers preferentially bind on the edge of a protein pattern as revealed by Kelvin force microscopy.

The effect of illumination on the depth profile of thermally annealed MEH‐PPV/dPS blends

Due to its simplicity and cost‐effectiveness, single solution casting of organic optoelectronics has grown in popularity for device fabrication to produce technologies such as organic photovoltaics and thin film transistors. In order to explore the structural evolution that occurs in the film formation of a blend composed of polystyrene and the benchmark conjugated polymer MEH‐PPV, we have performed a series of neutron reflectivity experiments focused on studying the film structure as it changes through the thermal annealing process both in the presence and absence of white light. Results indicate the formation of a nonhomogeneous blend upon casting, which becomes stratified with thermal annealing. More importantly, the extent of stratification varies with illumination, where exposure to white light increases stratification. This data suggests in situ illumination is a potential novel tool to manipulate device‐relevant morphologies of optoelectronic active layers throughout the fabrication process, offering a cheap nondestructive tool to effectively tune desired structural parameters. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1142–1149     

Supersonic molecular beam growth of thin films of organic materials: A novel approach to controlling the structure,morphology, and functional properties

Thin films of semiconducting molecular materials can be grown with a seeded supersonic molecular beam epitaxy (SuMBE), which provides unprecedented control over structural, morphological, and, therefore, functional properties. This novel technique of deposition takes full advantage of its ability to regulate the initial state of the molecular precursors in the beams and, in particular, the kinetic energy, to control the morphology, structure, and functional properties of growing films. This article reviews the state of the art of SuMBE, discussing the basic aspects of the technique and the major achievements so far. The major results obtained with respect to growth on dielectrics and metal substrates of films of oligothiophenes and pentacene and with respect to the codeposition of phthalocyanines and fullerenes are discussed and compared with the state of the art of more conventional organic molecular beam deposition. The potential impact of SuMBE in the field of π‐conjugated materials and devices is also examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2501–2521, 2003