掺杂Y2O3和BaCeO3提高MOD-YBCO超导性能的研究

本文通过在前驱液中添加过量钇盐和铈的有机盐,采用三氟乙酸盐-金属有机沉积法(TFA-MOD) 在铝酸镧单晶基体上制备了含有纳米氧化钇和纳米铈酸钡的YBCO薄膜. 与纯YBCO薄膜相比,掺杂Y₂O₃/BaCeO₃的YBCO膜的临界转变温度几乎保持不变,为91 K左右. 而掺杂Y₂O₃/BaCeO₃的YBCO膜的临界电流密度达到5.0 MA/cm² (77 K, 0T), 是纯YBCO膜临界电流密度的1.5倍.薄膜中的Y₂O₃和BaCeO₃可能在YBCO内部起到了 有效的钉扎磁通作用. 关键词： 钇钡铜氧薄膜 2O₃和纳米BaCeO₃')" href="#">纳米Y₂O₃和纳米BaCeO₃ 磁通钉扎 三氟乙酸盐-金属有机沉积     

钽掺杂对钛酸钡导热性能影响的研究

利用光热检测技术测量了钛酸钡材料的导热性能，得到了不同成型压力、烧结温度以及不同 掺杂量下的钛酸钡材料的热扩散率.研究了钽掺杂对钛酸钡材料导热性能的影响，发现了钽 元素掺杂量小于1.5mol%时，钛酸钡材料的热扩散率随掺杂量的增加而增大，当钽元素掺杂 量大于1.5mol%时，热扩散率随掺杂量的增加而减少.对钛酸钡材料的导热性能做了进一步的 分析. 关键词： 光热检测 钛酸钡 导热性能 钽掺杂     

Sr-doped LaInO3 and its possible application in a single layer SOFC

The effects of dopants on the electrical conductivity of the perovskite-type oxide LaInO₃ have been investigated. Replacement of La by Sr is the most effective way to enhance the conductivity of LaInO₃, whereas Ca substitution for In is rather difficult due to the large difference in the ion radii. The optimum composition is La_0.9Sr_0.1InO_3−δ whose maximum conductivity is 7.6×10⁻³ S cm⁻¹ at 900°C. The electrical conductivity of La_0.9Sr_0.1InO_3−δ has been measured over a wide range of oxygen partial pressure from pO₂=1 to 10⁻²⁵ atm. P-type and n-type behavior at high and low oxygen partial pressure have been observed, respectively, while at intermediate oxygen partial pressures, the electrical conductivity changes only slightly with the oxygen partial pressure. The concept of a single layer solid oxide fuel cell based on a La_0.9Sr_0.1InO_3−δ ceramic pellet has been tested. A maximum power density of 3 mW cm⁻² at 800°C was achieved when dilute H₂ and air were used as fuel and oxidizing agent, respectively.     

Investigation of the free volume and ionic conducting mechanism of poly（ethylene oxide）-LiClO_4 polymeric electrolyte by positron annihilating lifetime spectroscopy

The positron annihilation lifetime and ionic conductivity are each measured as a function of organophilic rectorite（OREC） content and temperature in a range from 160 K to 300 K.According to the variation of ortho-positronium（o-Ps） lifetime with temperature,the glassy transition temperature is determined.The continuous maximum entropy lifetime（MELT） analysis clearly shows that the OREC and temperature have important effects on o-Ps lifetime and free volume distribution.The experimental results show that the temperature dependence of ionic conductivity obeys the Vogel-Tammann-Fulcher（VTF） and Williams-Landel-Ferry（WLF） equations,implying a free-volume transport mechanism.A linear least-squares procedure is used to evaluate the apparent activation energy related to the ionic transport in the VTF equation and several important parameters in the WLF equation.It is worthwhile to notice that a direct linear relationship between the ionic conductivity and free volume fraction is established using the WLF equation based on the free volume theory for nanocomposite electrolyte,which indicates that the segmental chain migration and ionic migration and diffusion could be explained by the free volume theory.     

Effect of La doping in the multiferroic compound BiFeO3

We have performed magnetization and magnetocapacitance measurements on ceramic samples of the multiferroic series Bi_1−xLa_xFeO₃ for 0≤x≤.0.25. We show that doping with La reduces the transition magnetic field from the spatially modulated state to a homogenous one and increases the magnetocapacitance, these effects being the strongest for x=0.15, which is the highest concentration for maintaining the non-centrosymmetric rhomboedral structure (R3c) of BiFeO₃. For highest La content (x≥0.17), analysis of the XRD patterns shows that the lattice symmetry gradually changes to orthorhombic (C222), giving rise to an enhancement of the latent magnetization and to a drop of the magnetodielectric constant.     

Synthesis and ionic conduction of phases in the AgF-BiF3 system

Two types of phases have been prepared and characterized in the AgF-BiF₃ system at 400°C : AgBiF₄ which is isostructural with NaNdF₄ and a solid solution Ag_1-xBi_xF_1+2x (0.65 ?×?0.73) of the fluorite derived type. Ag_0.35Bi_0.65F_2.30 has the highest ionic conductivity (σ_100°C=3.5 10^-4ω^-1·cm^-1). The influenc of structural data on electrical properties is discussed.     

La2O3对Yb:Y2O3透明陶瓷光谱性能的影响

研究了La₂O₃对Yb：Y₂O₃透明陶瓷光谱性能的影响，添加适量La₂O₃以后，Yb：Y₂O₃透明陶瓷的吸收峰和发射峰的位置不变，但由于La³⁺的离子半径大于Y³⁺的离子半径，在Y₂O₃中引入La³⁺离子后，导致Y₂O₃晶格常数变大，晶场强度变弱，同时降低了Y₂O₃晶体的有序度，致使发射峰强度有所下降，发射截面变小.过量的La₂O₃（x=0.16）造成Yb³⁺激活离子发射强度明显下降；其荧光寿命在添加La₂O₃后总体增大45%—60%. 关键词： 氧化镧 氧化钇 透明陶瓷 光谱性能     

La$lt;sub$gt;0.4$lt;/sub$gt;Ca$lt;sub$gt;0.6$lt;/sub$gt;MnO$lt;sub$gt;3$lt;/sub$gt;中Mn-位Fe和Cr掺杂对磁性质的影响

研究了Fe和Cr掺杂对La_0.4Ca_0.6MnO₃ 中电荷有序反铁磁基态的调控作用. 磁性质的测量结果表明, 两种离子掺杂均能有效抑制原型样品中的长程电荷有序相, 但是Fe离子掺杂样品均具有反铁磁的基态, 而Cr掺杂样品中则出现了显著的铁磁性. 结合电输运测量结果显示, Cr掺杂引起的铁磁态同时具有金属性, 表明其中是电子双交换作用占主导. 对比两种掺杂离子的电子结构发现, Cr离子空的e_g电子轨道促进了电子双交换作用, 而Fe掺杂则只是引入了不同的自旋交换作用, 导致自旋无序. 关键词： 磁性氧化物 反铁磁     

Structural and DC conduction studies on vacuum evaporated BaTiO3 thin films prepared from BaTiO3 nano particles synthesised by wet chemical method

BaTiO₃ nanoparticles prepared by wet chemical method were thermally grown onto well cleaned glass substrates under the vacuum of 2 × 10⁻⁵ Torr, using 12A4 Hind Hivac coating unit. An Al–BaTiO₃–Al sandwich structure has been used for electrical conduction properties in the temperature range 303–423 K. The composition of nanoparticles and thin films were identified by EDS spectrum. The structural studies have been performed by the X-ray diffraction (XRD) technique. The X-ray analysis showed that the nano particle has a tetragonal structure and deposited films at a lower thickness amorphous in nature, whereas the crystallinity increases with increase of thickness. In the DC conduction studies, the current–voltage characteristics of the films showed ohmic conduction in the low voltage region. In the higher voltage region, a space charge limited conduction (SCLC) takes place due to the presence of the trapping level. The activation energy was estimated and the values found to decrease with increasing applied voltage. The zero field value of the activation energy is found to be 0.31 eV. The free carrier mobility, carrier density and trap density values were calculated and reported in this paper.     

聚合物纳米复合电解质(PEO)8-ZnO-LiClO4微结构及电导率研究

以聚氧化乙烯(PEO)为基质,成功制备出纳米ZnO掺杂的(PEO)₈-ZnO-LiClO₄离子导电聚合物电解质,并利用多种实验技术,包括扫描电子显微镜、X射线衍射(XRD)、傅里叶变换红外光谱和正电子湮没寿命谱(PALS),系统地研究了纳米ZnO与基质间相互作用及其对聚合物链段运动、纳米尺度自由体积、离子输运和复合电解质电导率的影响.实验结果发现,纳米ZnO的掺杂使聚合物电解质的离子电导率得到了大幅度提高,当ZnO与PEO质量比为6%时达到最大,(PEO)₈-ZnO-LiClO₄的电导率为1.82×10^-4 S ·cm^-1,比(PEO)₈-LiClO₄的电导率(6.58×10^-5 S ·cm^-1)提高了大约一个数量级.XRD结果显示,纳米ZnO的加入降低了PEO的结晶性,增加了锂离子传输的非晶相,从而提高了电导率.离散PALS测量结果表明,随着纳米ZnO的加入,复合电解质的自由体积、浓度和相对自由体积分数f_r均增加.连续PALS分析揭示了自由体积的分布由一个峰劈裂成两个峰,表明纳米ZnO的掺杂对聚合物的微结构有很大影响.基于实验测量的f_r和离子电导率,研究了离子导电机理.研究发现, f_r与电导率之间存在一个直接关系,即f_r越大,越有利于锂离子的传输,导致电导率越大.这个结果支持聚合物电解质导电的自由体积理论. 关键词： 正电子湮没寿命谱 聚合物纳米复合电解质 离子电导率 自由体积     

Calcium and oxygen doping in Y Ba2Cu3Oy

Both oxygen and calcium play important roles in inducing superconductivity in Y Ba₂Cu₃O_y (YBCO), which is an antiferromagnetic insulator at low O and Ca content. O induces superconductivity in Ca-free YBCO, while Ca does similarly in oxygen-deficient YBCO. For doping oxygen HgO was used as it decomposes at 476 ^°C into Hg, which escapes from the matrix leaving the crystal unaltered, and O, which provide a way to dope O in YBCO. Considering these facts, polycrystalline samples of Y _1−xCa_xBa₂Cu₃O_y with x=0, 0.1 and 0.2 with and without HgO addition were prepared through a solid-state reaction method. The samples were sintered at 950 ^°C in open atmosphere. These synthesized samples were characterized through using the X-ray diffraction technique (XRD) for phase evaluation, scanning electron microscopy (SEM) for grain morphology, energy dispersive X-ray analysis (EDX) for compositional analysis and the four-contact measurement technique for determining the superconducting transition temperature.     

ZnO-Bi2O3系压敏陶瓷的导电过程与等效势垒高度

研究了ZnO-Bi₂O₃系压敏陶瓷等效势垒高度_eff随着归一化电压的变化规律，发现等效势垒高度_eff随着归一化电压的增加先逐渐增大，达到最大值后持续下降.由于在外加电压作用下反偏势垒高度高于正偏势垒高度，等效势垒高度_eff主要取决于反偏势垒.因此，这种变化规律说明了ZnO压敏陶瓷晶界的导电过程可能存在三个阶段.在低归一化电压区，晶界区域中的电子从正偏势垒区注入到晶界无序层的速率低于电子从晶界无序 关键词： ZnO压敏陶瓷 归一化电压 等效势垒高度 导电过程     

Self-assembled 3D La(OH)3 and La2O3 nanostructures: Fast microwave synthesis and characterization

Self-assembled three-dimensional (3D) urchin-like and flower-like La(OH)₃ nanostructures were successfully prepared for the first time via a facile and fast microwave-assisted solution-phase chemical method in 15 min. The obtained products were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The SEM results reveal that the urchin-like and flower-like La(OH)₃ nanostructures are ca. 3 μm and 6 μm in diameter, respectively. The urchin-like La(OH)₃ nanostructures are constructed by nanorods with diameters of about 300 nm and lengths of about 500 nm. The flower-like La(OH)₃ nanostructures are built from nanopetals about 100 nm thick. The effects of reaction time, microwave power, amount of tetraethyl ammonium bromide (TEAB), and surfactants on the preparation were systematically investigated. The possible formation mechanism of the 3D La(OH)₃ nanostructures was preliminarily discussed. Urchin-like and flower-like La₂O₃ nanostructures were obtained after calcining the La(OH)₃ nanostructures at 800 °C for 4 h. Urchin-like and flower-like La₂O₃:Eu³⁺ nanostructures were also prepared and their photoluminescence (PL) properties were investigated.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

Effect of Mg and Ti doping on the luminescence of Y2O3:Eu

The Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV materials (x_Eu: 0.02, x_Mg: 0.08, x_Ti: 0.04) were prepared by solid state reaction. The purity and crystal structure of the material was studied with the X-ray powder diffraction. Luminescence properties were studied in the UV-VUV range with the aid of synchrotron radiation. The emission of Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV had a maximum at 612 nm (λ_exc: 250 nm) due to the ⁵D₀→⁷F₂ transition of Eu³⁺. The excitation spectra (λ_em: 612 nm) showed a broad band at 233 nm, due to the charge transfer transition between O²⁻ and Eu³⁺, and at 297 nm due to the Ti→Eu³⁺ energy transfer. Only very weak persistent luminescence was discovered. In the room and 10 K temperature excitation spectra, the line at 208 nm is due to the formation of a free exciton (FE) and a broad band at 199 nm was related to the valence-to-conduction band absorption of the Y₂O₃ host lattice. The absorption edge was ca. 205 nm giving 6.1 eV as the energy gap of Y₂O₃.     

Photoluminescence properties of Eu in Y(PO3)3 under VUV excitation

The photoluminescence properties of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) are investigated. The excitation spectrum of Y_0.85(PO₃)₃:0.15Eu₃⁺ shows that both the (PO₃)₃³⁻ groups and the CT bands of O²⁻-Y³⁺ can efficiently absorb the excitation energy in the region of 120-250 nm. Under 147 nm excitation, the optimal emissive intensity of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) is about 36% of the commercial phosphor (Y,Gd)BO₃:Eu³⁺, which hints that the absorbed energy by the host matrix could be efficiently transferred to Eu³⁺. We try to study the concentration quenching mechanism of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) under 147 and 172 nm excitation.     

Improvement of the superconducting properties of an infiltrated YBCO bulk superconductor by a BaCeO3 addition

Single grain YBa₂Cu₃O_7−x (Y123) bulk superconductors with Y₂BaCuO₅ (Y211) and various amounts of BaCeO₃ (5–45 wt.% by an increment of 10 wt.%) were fabricated by a seeded infiltration process. The addition of BaCeO₃ was found to be effective for a modification of the microstructure and an improvement of the superconducting properties. The refinement effect for Y211 particles within an entire superconducting YBa₂Cu₃O_7−x (Y123) matrix was achieved by BaCeO₃ additions. The critical current density (J_c) values were increased as the BaCeO₃ contents were increased (maximum J_c at 35 wt.% BaCeO₃ addition). The J_c improvement by BaCeO₃ additions might be due to the microstructure modifications associated with the finely distributed Y211 and BaCeO₃ particles. With the addition of BaCeO₃ the onset T_c values decreased slightly, indicating highly limited Ce substitution for Y site. It can be concluded that the BaCeO₃ addition has a beneficial effect on the morphology, the size and the distribution of the Y211 inclusions and the microstructure regarding pinning improvement.     

Ga掺杂对Cu_3SbSe_4热电性能的影响

采用熔融-淬火方法制备了Cu_(2.95)Ga_xSb_(1-x)Se_4(x=0,0.01,0.02和0.04)样品,系统地研究了Ga在Sb位掺杂对Cu_3SbSe_4热电性能的影响.研究结果表明,少量的Ga掺杂(x=0.01)可以有效提高空穴浓度,抑制本征激发,改善样品的电输运性能.掺Ga样品在625 K时功率因子达到最大值10μW/cm·K~2,比未掺Ga的Cu_(2.95)SbSe_4样品提高了约一倍.但是随着Ga掺杂浓度的进一步提高,缺陷对载流子的散射增强,同时载流子有效质量增大,导致载流子迁移率急剧下降.因此Ga含量增加反而使样品的电性能恶化.在热输运方面,Ga掺杂可以有效降低双极扩散对热导率的贡献,同时掺杂引入的点缺陷对高频声子有较强的散射作用,因此高温区的热导率明显降低.最终该体系在664 K时获得最大ZT值0.53,比未掺Ga的样品提高了近50%.     

On ionic conduction in the α-phase of PbSnF4

The structure re-refinement of tetragonal PbSnF₄ was executed using data reported earlier. The rms amplitude in M2(Sn) site is larger in (001) plane than along the c-axis and the thermal vibrations of F3 fluorine ions are very large, i.e. B_eq = 12.415(20) A². M2F₈ polyhedra form a distorted cube. The fluorine ions on the F3 site are present between the M2 ion layers. The fluorine ions on the F3 site are located between the M2 ion layers and their weak bonds to Sn ions play an important role in the conduction. The ionic conductivity in the (001) plane is higher than that in the 001 direction.     

Deuterium conductivity, diffusion and implantation in Sr-doped LaYO3

A study of deuterium conductivity and diffusion in the oxide perovskite La_0.9Sr_0.1YO_3−δ is presented in this work. Deuterium ions were implanted into La_0.9Sr_0.1YO_3−δ (50 keV, 1×10¹⁶ atoms/cm²) and the corresponding deuterium depth profile was determined by SIMS and compared with a Monte Carlo simulation (TRIM96). This implant was used as a standard for the determination of deuterium concentration in a La_0.9Sr_0.1YO_3−δ sample pre-treated in D₂O atmosphere. In this way, it was fully confirmed that La_0.9Sr_0.1YO_3−δ incorporates water at high temperatures. The conductivity of La_0.9Sr_0.1YO_3−δ was measured in D₂O atmosphere and compared with other proton (deuteron) conductors. Concentration and conductivity data were used in conjunction to estimate the deuterium diffusivity and the constant of reaction of (heavy) water incorporation into LaYO₃. Some comments on the catalytic activity of this oxide are made.