Synthesis of CeVO<Subscript>4</Subscript> Crystals with Different Sizes and Shapes

Tetragonal CeVO₄ was prepared through hydrothermal treatment and sonication method with the same precursor in the absence of any catalysts or templates, and the products were characterized by XRD, TEM and Raman. It is found that microrods, nanoparticles, nanorods and nanoplates have been obtained. The bigger nanorods produced through hydrothermal treatment have average diameters of 15–25 nm and lengths of 20–60 nm. The smaller nanorods prepared through ultrasound treatment have average diameters of 6–12 nm and lengths of 10–18 nm. Uniform nanoplates have been produced. The nanoplates produced through hydrothermal method are composed of CeVO₄ and CeO₂. The mechanism of shape changing has been discussed. And the existing vanadium which is sensitive to the pH value of synthesis solution may be a key factor for the resulted sizes and shapes of the obtained nanocrystals. The samples prepared through hydrothermal treatment and sonication method were used as the catalysts for the combustion of trichloroethylene to test their catalytic activity.     

Enhancement of electrochemical properties of MoO<Subscript>3</Subscript> nanobelts electrode using PEG as surfactant for lithium battery

Molybdenum trioxide (MoO₃) has attracted considerable attention due to their typical two-dimensional layered structure consisting of double layers of edge- and vertex-sharing MoO₆ octahedral being weakly held together by van der Waals bonds. These MoO₃ nanostructures and their polymer composites are currently drawing interest for the potential applications of Li batteries, supercapacitors, and other electrochemical as well as electrochromic display devices. In this paper, we report the synthesis of MoO₃ nanobelts and polyethylene glycol (PEG) surfactant MoO₃ nanobelts by hydrothermal method. Structure and morphology of the samples were investigated by X-ray diffraction, Fourier transform spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM). The pure MoO₃ nanobelts show an initial specific capacity of 275 mAh g⁻¹, whereas the 0.5 mol% PEG surfactant MoO₃ nanobelts show 307 mAh g⁻¹ at constant current density of 30.7 mA g⁻¹ with the 1.0–3.0 V vs. Li/Li⁺ potential range. It was found that PEG surfactant MoO₃ nanobelts show not only a high initial specific capacity but also show better cyclic performance compared with that of pure MoO₃ nanobelts. The PEG surfactant MoO₃ nanobelts show stability and improvement of the specific capacity due to decreasing the length, width, and thickness of the nanobelts by surface reaction. Electrochemical impedance spectroscopy reveals that the PEG surfactant MoO₃ nanobelts exhibit low electrode resistance compared with pure MoO₃ nanobelts.     

MoO3−δ nanorods: Synthesis,characterization and magnetic properties

A novel preparation method of MoO_2.987 nanorods and the thorough investigation of their structural and magnetic properties by means of X-ray diffraction and infrared spectroscopy as well as by scanning and transmission electron microscopy are reported. MoO_3−δ nanorods were prepared via hydrothermal treatment of a mixture made from molybdenum peroxide solution and oxalic acid. The presented synthesis approach is very simple, of low-cost and can be a perspective for industrial manufacturing. The resulting single crystalline nanorods exhibit diameters of 60–90 nm and lengths up to several micrometers. The crystal structure was found to be orthorhombic as in α-MoO₃. This agrees with our magnetization data which imply non-magnetic Mo⁶⁺ ions but show only a small amount of magnetic impurities giving rise to a weak paramagnetic response.     

Electrochromic properties of MoO<Subscript>3</Subscript> thin films derived by a sol–gel process

Molybdenum trioxide (MoO₃) films were deposited on ITO/Glass substrates by the sol–gel method using a spin-coating technique and heat treated at various temperatures under different ambient atmosphere. Effects of the process parameters on the electrochromic properties of MoO₃ films were studied using cyclic voltammetry (CV) in a propylene carbonate (PC) non-aqueous solution containing 1 M lithium perchlorate (LiClO₄). Electrochromic MoO₃ film on lithium intercalation was investigated by in-situ transmittance measurement during the CV process. The MoO₃ films showed reversible recharge ability on Li⁺/e⁻ intercalation/deintercalation. Experimental results revealed that the heat-treatment temperature, the ambient atmosphere, and the thickness will have the string influence on the electrochromic properties of MoO₃ thin films. X-ray diffraction (XRD) results show that the amorphous MoO₃ films can be obtained with the heat-treatment temperature below 300 °C in O₂ ambient atmosphere. The optimum electrochromic MoO₃ film, with a thickness of 130 nm, exhibits a maximum transmittance variation (ΔT%) of 30.9%, an optical density change (ΔOD) of 0.213, an intercalation charge (Q) of 8.47 mC/cm², an insertion coefficient x in Li _x MoO₃ was 0.21 and a coloration efficiency (η) of 25.1 cm²/C between the colored and bleached states at a wavelength (λ) of 550 nm.     

Synthesis, structural and transport properties of Li-doped molybdenum and vanadium oxide nanocrystalline films

The aim of this study was to determine an influence of lithium excess in nanocrystalline xLi₂O–(80 − x)V₂O₅–20MoO₃, nH₂O (0 ≤ x ≤ 15 mol.%) on their transport and structural properties. The obtained nanorods have width of 8–24 nm with lengths up to 200 nm. The density of the samples decreases with increasing Li content. The electrical conductivity shows that all samples are semiconductor and decreases with increasing Li content. From the best fits, reasonable values of various small polaron hopping parameters were obtained. The density of state N(E _F ) values were evaluated and found to vary from 2.76 to 11.14 × 10²¹ eV⁻¹ cm⁻³. The values of optical phonon frequency (ν _o ) were obtained to be 1.36–1.61 × 10¹³ Hz. The electrical conduction at T > θ_D/2 was due to non-adiabatic SPH.     

Core–Shell α‐Fe2O3@α‐MoO3 Nanorods as Lithium‐Ion Battery Anodes with Extremely High Capacity and Cyclability

α‐Fe₂O₃ nanoparticles are uniformly coated on the surface of α‐MoO₃ nanorods through a two‐step hydrothermal synthesis method. As the anode of a lithium‐ion battery, α‐Fe₂O₃@α‐MoO₃ core–shell nanorods exhibit extremely high lithium‐storage performance. At a rate of 0.1 C (10 h per half cycle), the reversible capacity of α‐Fe₂O₃@α‐MoO₃ core–shell nanorods is 1481 mA h g^?1 and a value of 1281 mA h g^?1 is retained after 50 cycles, which is much higher than that retained by bare α‐MoO₃ and α‐Fe₂O₃ and higher than traditional theoretical results. Such a good performance can be attributed to the synergistic effect between α‐Fe₂O₃ and α‐MoO₃, the small size effect, one‐dimensional nanostructures, short paths for lithium diffusion, and interface spaces. Our results reveal that core–shell nanocomposites have potential applications as high‐performance lithium‐ion batteries.     

One-dimensional MoO2 nanorods for supercapacitor applications

One-dimensional (1D) MoO₂ nanorods were prepared by thermal decomposition of tetrabutylammonium hexamolybdate (((C₄H₉)₄N)₂Mo₆O₁₉) in an inert atmosphere. The synthesized nanorods have been characterized by XRD, TEM and HRTEM. The capacitive behaviour of 1D MoO₂ nanorods was studied by galvanostatic charge–discharge studies in 1 M H₂SO₄ solution at different current densities. The results indicate that the MoO₂ nanorods show good capacitive behaviour with a specific capacitance of 140 Fg^?1.     

Catalytic dehydrogenation of cyclohexene over MoO<Subscript>3</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

A series of MoO₃/γ-Al₂O₃ catalysts with different Mo surface densities (Mo atoms/nm²) has been prepared by incipient wetness impregnation method. Structural characteristics of the prepared catalysts were investigated by atomic absorption spectroscopy, X-ray diffraction, Fourier Transform Infrared spectroscopy, N₂ adsorption at −196 °C, and temperature-programmed reduction (TPR). The catalytic activities of the prepared catalysts were tested by cyclohexene conversion between 200 and 400 °C. XRD results indicated that molybdenum oxide species were dispersed as a monolayer on the support up to 4.04 Mo atoms/nm², and the formation of crystalline MoO₃ was observed above this loading. FTIR and TPR results showed that molybdenum oxide species were present predominantly in tetrahedral form at lower loading, and polymeric octahedral forms were dominant at higher loading. Cyclohexene conversion reaction proceeded mainly through the simple dehydrogenation pathway in the studied temperature range 200–400 °C and was found to be highly dependent on MoO₃ dispersion.     

Electrochemical performance of new α-MoO3 nanobelt cathode materials for rechargeable Li-ion batteries

The orthorhombic molybdenum trioxide (α-MoO₃) nanobelts and polyvinyl pyrrolidone (PVP) surfactant MoO₃ nanobelts with high quality were prepared through hydrothermal synthesis. The morphology and microstructure of the samples were investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The nanobelts with rectangular cross-section have an orthorhombic phase structure, preferentially grow in [001] direction. The results showed that the H atoms in polyvinyl pyrrolidone are H-bonded with the O atoms in the MoO bonds of MoO₃ nanobelts. When MoO₃ is modified by the intercalation of PVP, it is effectively shielded against electrostatic interaction between the MoO₃ interlayer and Li⁺ ions. The specific capacity of pure MoO₃ nanobelts battery and (PVP)_0.2MoO₃ nanobelts exhibit as 195 mAh g⁻¹ and 237 mAh g⁻¹, respectively after 14 cycles, suggests that the stability of surfactant material is worthy.     

Magnesium ion-conducting gel polymer electrolytes dispersed with fumed silica for rechargeable magnesium battery application

Effect of fumed silica dispersion on poly(vinylidene fluoride-co-hexafluoropropylene)-based magnesium ion-conducting gel polymer electrolyte has been studied using various physical and electrochemical techniques. The composite gel electrolytes are free-standing and flexible films with enough mechanical strength. The optimized composition with 3 wt.% filler offers a maximum ionic conductivity of ∼1.1 × 10⁻² S cm⁻¹ at ∼25 °C with good thermal and electrochemical stabilities. The Mg²⁺ ion conduction in the gel nanocomposite film is confirmed from the cyclic voltammetry, impedance spectroscopy, and transport number measurements. The space-charge layers formed between filler particles and gel electrolyte are responsible for the enhancement in ionic conductivity. The applicability of the gel nanocomposite to a rechargeable battery is examined by fabricating a prototype cell consisting of Mg [or Mg-multiwalled carbon nanotube (MWCNT) composite] and MoO₃ as negative and positive electrodes, respectively. The discharge capacity and the rechargeability of the cell have been improved when Mg metal is substituted by Mg-MWCNT composite. The discharge capacity of the optimized cell has found to be ∼175 mAh g⁻¹ of MoO₃ for an initial ten charge–discharge cycles.     

Synthesis and supercapacitance of flower-like Co(OH)<Subscript>2</Subscript> hierarchical superstructures self-assembled by mesoporous nanobelts

A facile hydrothermal strategy was first proposed to synthesize flower-like Co(OH)₂ hierarchical microspheres. Further physical characterizations revealed that the flower-like Co(OH)₂ microspherical superstructures were self-assembled by one-dimension nanobelts with rich mesopores. Electrochemical performance of the flower-like Co(OH)₂ hierarchical superstructures were investigated by cyclic voltammgoram, galvanostatic charge–discharge and electrochemical impedance spectroscopy in 3 M KOH aqueous electrolyte. Electrochemical data indicated that the flower-like Co(OH)₂ superstructures delivered a specific capacitance of 434 F g⁻¹ at 10 mA cm⁻² (about 1.33 A g⁻¹), and even kept it as high as 365 F g⁻¹ at about 5.33 A g⁻¹. Furthermore, the SC degradation of about 8% after 1,500 continuous charge–discharge cycles at 5.33 A g⁻¹ demonstrates their good electrochemical stability at large current densities.     

On the sol–gel preparation of different tungstates and molybdates

The preparation and characterization of the M′–M′′–O nitrate–tartrate (M′ = Ca, Ba, Gd and M′ = W, Mo) precursor gels synthesized by simple, inexpensive, and environmentally benign aqueous sol–gel method is reported. The obtained gels were studied by thermal (TG/DSC) analysis. TG/DSC measurements revealed the possible decomposition pathway of synthesized M′–M′′–O nitrate–tartrate gels. For the synthesis of different metal tungstates and molybdates, the precursor gels were calcined at different temperatures (650, 800, and 900 °C). According to the X-ray diffraction (XRD) analysis data, the crystalline compounds CaMo_1-x W _x O₄ doped with Ce³⁺ ions, BaMo_1-x W _x O₄ doped with Eu³⁺ ions and Gd₂Mo₃O₁₂ were obtained from nitrate–tartrate gels annealed at 650–900 °C temperatures. The XRD data confirmed that the fully crystalline single-phase powellite, scheelite, or Gd₂(MoO₄)₃ structures were formed already at 650 °C. Therefore, the suggested sol–gel method based on the complexation of metal ions with tartaric acid is suitable for the preparation of mixed tungstates–molybdates at relatively low temperature in comparison with solid-state synthesis.     

Effect of MoO<Subscript>3</Subscript> additions on the thermal stability and crystallization kinetics of PbO–Sb<Subscript>2</Subscript>O<Subscript>3</Subscript>–As<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

The present paper reports on the effect of MoO₃ on the glass transition, thermal stability and crystallization kinetics for (40PbO–20Sb₂O₃–40As₂O₃)_100−x –(MoO₃) _x (x = 0, 0.25, 0.5, 0.75 and 1 mol%) glasses. Differential scanning calorimetry (DSC) results under non-isothermal conditions for the studied glasses were reported and discussed. The values of the glass transition temperature (T _g) and the peak temperature of crystallization (T _p) are found to be dependent on heating rate and MoO₃ content. From the compositional dependence and the heating rate dependence of T _g and T _p, the values of the activation energy for glass transition (E _g) and the activation energy for crystallization (E _c) were evaluated and discussed. Thermal stability for (40PbO–20Sb₂O₃–40As₂O₃)_100−x –(MoO₃) _x glasses has been evaluated using various thermal stability criteria such as ΔT, H _r , H _g and S. Moreover, in the present work, the K _r(T) criterion has been considered for the evaluation of glass stability from DSC data. The stability criteria increases with increasing MoO₃ content up to x = 0.5 mol%, and decreases beyond this limit.     

Determination of thermodynamic stability of CdMoO4 by knudsen effusion vapor pressure measurement method

Thermodynamic stability of CdMoO₄ was determined by measuring the vapor pressures of Cd and MoO₃ bearing gaseous species. Th vaporization reaction could be described as CdMoO₄(s)+MoO₂(s) =Cd(g)+2/n(MoO₃)_n (n=3, 4 and 5). The vapor pressures of the cadmium (p _Cd) and trimer (p _(MoO3)3) measured in the temperature range 987≤T/K≤1111 could be expressed, respectively, as ln (p _Cd/Pa) = –32643.9/T+29.46±0.08 and ln(p _(MoO3)3/Pa) = –32289.6/T+29.28±0.08. The standard molar Gibbs free energy of formation of CdMoO₄(s), derived from the vaporization results could be expressed by the equations: °_f G _{CdMoO4 (s)} ⁰= –1002.0+0.267T±14.5 kJ mol^–1 (987≤T/K≤1033) and °_f G _{CdMoO4 (s)} ⁰ = –1101.9+0.363T±14.4 kJ mol^–1 (1044≤T/K≤1111). The standard enthalpy of formation of CdMoO₄(s) was found to be –1015.4±14.5 kJ mol^–1 .     

核壳结构MoOx/C微球的制备及储锂性能

采用水热法合成了MoO_3/酚醛树脂前驱体,然后在空气中进行煅烧处理,成功制备了一种新型核壳MoOx/C微球。对材料的晶体结构、形貌和元素价态进行分析表明,该材料的主要成分是单斜相MoO_2、正交晶系MoO_3和碳。树脂在空气中的煅烧碳化将MoO_3/酚醛树脂前驱体中的六方晶系的MoO_3还原为单斜相MoO_2。其中少量的MoO_2会在空气中重新被氧化成正交晶系的MoO_3,形成了MoO_2/MoO_3异质结构。在这一系列反应的综合作用下,形成这种表面有裂纹的核壳MoOx/C微球复合材料。将该材料用作锂离子电池负极材料,表现出了循环稳定性高、倍率性能好等优异的电化学性能。在100 mA·g-1的电流密度下充放电循环100次之后,可逆容量达640.6 mAh·g-1。     

Optical,structural and electrochromic studies of molybdenum oxide thin films with nanorod structure

The MoO₃ thin films were prepared via sol–gel dip coating method on glass and FTO glass substrate. The optical and other properties of multilayered MoO₃ films with 2–10 layers were investigated. The MoO₃ films were studied using UV–Visible transmission, XRD, SEM, FTIR and Cyclic Voltammetry (CV) measurements. The band gap value for MoO₃ films was evaluated and in the range of 3.2 eV–3.72 eV. The XRD spectrum reveals that the crystallinity increases along the (020) and (040) planes with the increase in thickness. The SEM images showed the formation of nanorods upto six layers. The FTIR spectrum confirms the formation of MoO₃. The 6 layered films show the maximum anodic (spike)/cathodic (peak) diffusion coefficient of 18.84/1.701 × 10^?11 cm²/s. The same film exhibits the change in optical transmission of 49% with the bleached/coloured state transmission of 62/13%.     

Tremella-like molybdenum dioxide consisting of nanosheets as an anode material for lithium ion battery

Tremella-like structured MoO₂ consisting of nanosheets was obtained via a Fe₂O₃-assisted hydrothermal reduction of MoO₃ in ethylenediamine aqueous solution. The as-prepared product was characterized and tested with scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and capacity measurement as anode material for lithium ion batteries. This structured MoO₂ shows very high reversible capacity (>600 mA h g⁻¹), good rate capability and cycling performance, presenting potential application as anode material for lithium ion batteries with high rate capability and high capacity.     

Synthesis,crystal structures,and magnetic properties of two manganese(II) coordination polymers bearing 1,1′-biphenyl-3,3′-dicarboxylate ligands

Two Mn(II) coordination polymers, namely [Mn(bpda)] _n (1) and [Mn(bpda)(bpy)_0.5] _n (2) (H₂bpda = 1,1′-biphenyl-3,3′-dicarboxylic acid and bpy = 4,4′-bipyridine), have been synthesized from H₂bpdc, bpy, and MnSO₄·2H₂O under hydrothermal conditions. The complexes were characterized by physicochemical and spectroscopic methods, as well as by X-ray crystallography. Compound 1 possesses a 3D structure consisting of carboxylate-bridged edge-sharing Mn–O–Mn double chains. Compound 2 features a 3D open structure with a dinuclear Mn(II) secondary building unit. Magnetic susceptibility measurements of compounds 1 and 2 exhibit antiferromagnetic interactions between the nearest Mn(II), with J = –11.3 cm⁻¹ and g = 2.12 for 1, and J = –13.5 cm⁻¹ and g = 2.12 for 2.     

New cadmium and rare-earth metal molybdato–tungstates with scheelite-type structure

A new group of cadmium and rare-earth metal molybdato–tungstates with the formula Cd_0.25 RE _0.50□_0.25(MoO₄)_0.25(WO₄)_0.75 (RE = Pr, Nd, Sm–Dy, □—vacancies in cation sublattice) were synthesized by a high-temperature solid-state reaction between RE ₂MoO₆ and CdWO₄ mixed at the molar ratio of 1:3. Powder X-ray diffraction measurements showed that obtained phases adopt the scheelite-type structure. The phases melt congruently in the temperature range of 1382–1458 K.     

An electrochemical investigation on (MoO<Subscript>3</Subscript>+PVP+PVA) nanobelts for lithium batteries

Molybdenum trioxide (MoO₃) xerogel films modified with poly(vinyl alcohol)+poly(vinyl pyrrolidone) (PVP+PVA) polyblends were obtained by ion-exchange method with sol-gel technique. Investigations were conducted using X-ray “diffractometry”, Fourier transform infrared spectroscopy, and cyclic voltammetry. The results show that the H atoms in polyblend are H-bonded with the O atoms in the Mo=O bonds of MoO₃ xerogel, which effectively shield the electrostatic interaction between MoO₃ interlayer and Li⁺ ions when MoO₃ xerogel is modified by the intercalation of (PVP+PVA). The reversibility of the insertion/extraction of Li⁺ ions is greatly improved by the modification with polyblend of MoO₃ nanocomposite films. MoO₃ and (PVP+PVA) _x MoO₃ (x = 0, 0.5) nanobelts were obtained by a simple hydrothermal process from MoO₃ sol. The electrochemical cells with configuration Li/(LiPF₆+EC+DMC)/MoO₃ modified by (PVP+PVA) were fabricated and their discharge profiles studied.