共查询到15条相似文献,搜索用时 486 毫秒
1.
2.
3.
中心螺管是超导托卡马克装置磁体系统的重要组成部分 ,在 HT- 7U中 ,中心螺管采用管装超导电缆绕制 ,线圈以脉冲方式运行。文中介绍了 HT- 7U中心螺管模型线圈实验中 ,失超信号检测系统的工作原理及失超信号特点。当磁体以脉冲方式运行时 ,失超信号检测系统为装置提供可靠的失超保护动作信号 ;还给出了有关的实验数据和检测系统记录的失超信号变化曲线。 相似文献
4.
《低温物理学报》2016,(2)
高温超导储能磁体(HTS-SMES)是电力系统中的重要应用.文中设计了一种0.5MJ级SMES装置,采用YBCO高温超导带材绕制为14组线圈饼,每组线圈饼由四个单饼线圈组成,设计工作温度为20K,工作电流100A.SMES装置在运行时,中心磁场接近3T,保证高磁场下YBCO带材的临界电流是SMES装置正常运行的必要条件.文中通过有限元的方法分析了运行工况下SMES装置的漏磁场,线圈内磁感应强度的分布,在该磁场条件下带材性能满足运行条件.通过电磁,结构耦合计算与冷却过程的应力分析,得到了线圈上的米塞斯应力与形变,满足储能磁体运行的条件,可以为SMES装置的设计和运行提供参考. 相似文献
5.
6.
7.
8.
9.
10.
高温超导电缆、线圈和磁体的失超探测一直都是一个难点。利用基于光纤光栅传感技术的多光栅串温度监测系统,通过检测温度的实时变化为快速探测失超并准确找到失超点提供了一种新的方法。通过多次对高温超导带材失超探测实验,结果表明,在超导带材失超时,多光栅串会同时发生中心波长位移,表明带材温度变化可以被光栅串实时监测。通过理论计算和实验测定,验证了基于多光栅串探测高温超导失超的可行性,为后续的高温超导磁体和超导电缆的失超探测提供了一种新方法。 相似文献
11.
介绍了FAIR项目Super-FRS超导二极磁铁样机的基于FPGA的失超探测系统。该失超探测系统采用平衡桥路法, 并通过两组独立桥路以消除失超探测死区。 通过NI PXI 7830R FPGA模块实现平滑滤波和失超判断算法,并给出失超触发信号。失超数据采集模块采用预采样技术, 将失超前后一段时间内的数据采集下来,以便进行后续分析。 通过测试,失超探测模块准确检测到了失超的发生, 并触发失超保护电路和失超数据采集模块工作,有效地保护了超导二极磁铁。 : The quench detection system for Super FRS super ferric dipole prototype magnet of FAIR has been designed and built. The balance bridge was used to detect quench signal. In order to avoid blind zone of quench detection, two independent bridges were used. NI PXI 7830R FPGA was used to implement filter to quench signal and algorithm of quench decision and to produce quench trigger signal. Pre sample technique was used in quench data acquisition. The data before and after quench could be recorded for analysis later. The test result indicated that the quench of the dipole’s superconducting coil could be reliably detected by the quench detection module. 相似文献
12.
13.
A NbTi 7 T superconducting magnet with a 338 mm bore system was rebuilt and the first expe-riment was carried out in Jan. 2009. The balancing-bridge method used for the quench detection system is analyzed and an improvement of the principle of balancing-bridge conformation is given. The inductances of the coils are calculated to estimate the proportion of the bridge arms. The appropriate parameters are selected for the balancing-bridge. 相似文献
14.
A NbTi 7 T superconducting magnet with a 338 mm bore system was rebuilt and the first experiment was carried out in Jan. 2009. The balancing-bridge method used for the quench detection system is analyzed and an improvement of the principle of balancing-bridge conformation is given. The inductances of the coils axe calculated to estimate the proportion of the bridge arms. The appropriate parameters axe selected for the balancing-bridge. 相似文献
15.
A superconducting solenoid prototype magnet for Accelerator Driven Subcritical System (ADS) Injection Ⅰ has been designed and fabricated, which has also been tested in a liquid Helium state inside a vertical Dewar in the Haerbin institute of Technology in November 2012. The design current was 210 A, when the test current reached 400 A no quench occurred so the solenoid magnet was forced to quench by the embedded heaters. The integral field strength, leakage field at the nearby upstream and downstream superconducting spoke cavities all meet the design requirements. At the same time, it also checked the reliability of the vertical test Dewar and the quenched detection system. The superconducting prototype magnet has accumulated valuable experiences for the coming batch magnets production and cryogenic test. 相似文献