Preparation and Characterization of Head-to-Head Polymers. II. Head-to-Head Poly(methyl Acrylate)

Head-to-head poly(methyl acrylate) was prepared by esterification of the known alternating copolymer of ethylene and maleic anhydride. Some of the chemical,physical, and mechanical properties and the thermal degradation behavior of head-to-head poly(methyl acrylate) were studied and compared with those of head-to-tail poly(methyl acrylate). The T_g of the head-to-head polymer was higher than that of the head-to-tail polymer, but the solubilities of both types of polymers of comparable molecular weight were similar. Head-to-head poly(methyl acrylate) degraded thermally at approximately the same temperature and with a rate similar to head-to-tail poly(methyl acrylate). Unlike poly(methyl cinnamates) which cleanly degraded to monomers, poly(methyl acrylates), head-to-head and head-to-tail, degrade to very small molecules, such as CO₂, methanol, but also larger polymer fragments and char. Trace amounts of monomers (methyl acrylate) were also observed.     

Thermal stability of copolymers of vinyl acetate and methyl acrylate

The thermal degradation of a series of copolymers of vinyl acetate and methyl acrylate and the two homopolymers poly(vinyl acetate) and poly(methyl acrylate) obtained using Ce(IV) as initiator has been investigated using differential thermal analysis (DTA) and thermogravimetry (TGA) in dynamic nitrogen. The kinetic parameters E, n, and A have been obtained following several methods of thermogravimetric analyses. The stability increases as the methyl acrylate content in the copolymer composition increases. The incorporation of 5 mol % of vinyl acetate in the copolymer produces a marked decrease in stability compared to the homopolymer poly(methyl acrylate). There is evidence for an intramolecular lactonization process in vinyl acetate—methyl acrylate copolymers.     

Photolysis of polymers using the medium pressure mercury lamp: Part 1—Photolysis and product analysis apparatus and the effect of some experimental variables

A photolysis cell, designed for irradiation of a polymer film deposited on a stainless steel support under closely controlled temperature conditions, is described. Using an evacuated system, detection and estimation of small amounts of volatile products may be carried out by subambient thermal volatilisation analysis (SATVA). Illustrative SATVA results are presented for the photolyses of poly(methyl acrylate) and poly(2-ethylhexyl acrylate). Each product appears as a peak on the SATVA trace, which is a record of rate of transfer of volatile material as a function of time, as products are allowed to warm up slowly from ?196°C to ambient temperature. The area under a given SATVA peak measures the amount of substance volatilised. Calibration data are given, relating peak area to moles of material for each of the various products.The effect of lamp to sample distance, film thickness and irradiation time on the yield of condensable volatile products has been tested for poly(methyl acrylate) in order to establish optimum conditions for use of the apparatus.     

Photooxidative and pyrolytic degradation of methyl methacrylate-alkyl acrylate copolymers

Different compositions of poly(methyl methacrylate-co-methyl acrylate) (PMMAMA), poly(methyl methacrylate-co-ethyl acrylate) (PMMAEA) and poly(methyl methacrylate-co-butyl acrylate) (PMMABA) copolymers were synthesized and characterized. The photocatalytic oxidative degradation of all these copolymers were studied in presence of two different catalysts namely Degussa P-25 and combustion synthesized titania using azobis-iso-butyronitrile and benzoyl peroxide as oxidizers. Gel permeation chromatography (GPC) was used to determine the molecular weight distribution of the samples as a function of time. The GPC chromatogram indicated that the photocatalytic oxidative degradation of all these copolymers proceeds by both random and chain end scission. Continuous distribution kinetics was used to develop a model for photocatalytic oxidative degradation considering both random and specific end scission. The degradation rate coefficients were determined by fitting the experimental data with the model. The degradation rate coefficients of the copolymers decreased with increase in the percentage of alkyl acrylate in the copolymer. This indicates that the photocatalytic oxidative stability of the copolymers increased with increasing percentage of alkyl acrylate. From the degradation rate coefficients, it was observed that the photocatalytic oxidative stability follows the order PMMABA > PMMAEA > PMMAMA. The thermal degradation of the copolymers was studied by using thermogravimetric analysis (TGA). The normalized weight loss and differential fractional weight loss profiles indicated that the thermal stability of the copolymer increases with an increase in the percentage of alkyl acrylate and the thermal stability of poly(methyl methacrylate-co-alkyl acrylate)s follows the order PMMAMA > PMMAEA > PMMABA. The observed contrast in the order of photostability and thermal stability of the copolymers was attributed to different mechanisms involved for the scission of polymer chain and formation of different products in both the processes.     

A theory-based approach to thermal field-flow fractionation of polyacrylates

A theory-based approach is presented for the development of thermal field-flow fractionation (ThFFF) of polyacrylates. The use of ThFFF for polymer analysis has been limited by an incomplete understanding of the thermal diffusion which plays an important role in retention and separation. Hence, a tedious trial-and-error approach to method development has been the normal practice when analyzing new materials. In this work, thermal diffusion theories based on temperature dependent osmotic pressure gradient and polymer-solvent interaction parameters were used to estimate thermal diffusion coefficients (D(T)) and retention times (t(r)) for different polymer-solvent pairs. These calculations identified methyl ethyl ketone as a solvent that would cause significant retention of poly(n-butyl acrylate) (PBA) and poly(methyl acrylate) (PMA). Experiments confirmed retention of these two polymers that have not been previously analyzed by ThFFF. Theoretical and experimental D(T)s and t(r)s for PBA, PMA, and polystyrene in different solvents agreed to within 20% and demonstrate the feasibility of this theory-based approach.     

Thermal degradation of bromine-containing polymers. Part 3—Blends of poly(2-bromoethyl methacrylate) and poly(methyl acrylate)

Films of a blend of equal weights of poly(2-bromoethyl methacrylate) (P2BEM) and poly(methyl acrylate) (PMA) were prepared by evaporation of a solution in acetone. The principal characteristics and products of the thermal degradation of the blend were established by the application of thermal analysis and infra-red and mass spectrometric techniques. Similarities to the degradation behaviour of copolymers of 2-bromoethyl methacrylate (2BEM) and methyl acrylate (MA) were noted.     

Development of hydrogenated ring‐opening metathesis polymers

New hydrogenated ring‐opening metathesis polymers with excellent thermal and optical properties were developed. These polymers were prepared by the ring‐opening metathesis polymerization of ester‐substituted tetracyclododecene monomers followed by the hydrogenation of the main‐chain double bond. The degree of hydrogenation was an important factor for the thermal stability of the polymers, and as complete hydrogenation as possible was necessary to obtain a thermally stable polymer. The completely hydrogenated ring‐opening polymer derived from 8‐methyl‐8‐methoxycarbonyl‐substituted monomer has a glass‐transition temperature of 171 °C and a 5% weight‐loss temperature of 446 °C. This polymer has excellent thermal and optical properties because of its bulky and unsymmetrical polycyclic structure in the main chain and is an alternative to glass or other transparent polymers such as poly(methyl methacrylate) and polycarbonate resin. This polymer has also been used in a wide variety of applications, such as optical lenses, optical disks, optical films, and optical fiber. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4661–4668, 2000     

N‐Bromosuccinimide as a thermal iniferter for radical polymerization

N‐Bromosuccinimide (NBS) was used as a thermal iniferter for the initiation of the bulk polymerizations of methyl methacrylate, methyl acrylate, and styrene. The polymerizations showed the characteristics of a living polymerization: both the yields and the molecular weights of the resultant polymers increased linearly as the reaction time increased. The molecular weight distributions of the polymers were 1.42–1.95 under the studied conditions. The resultant polymers could be used as macroiniferters to reinitiate the polymerization of the second monomer. The copolymers poly(methyl methacrylate)‐b‐polystyrene and polystyrene‐b‐poly(methyl methacrylate) were obtained and characterized. End‐group analysis of the resultant poly(methyl methacrylate), poly(methyl acrylate), and polystyrene confirmed that NBS behaved as a thermal iniferter. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2567–2573, 2005     

Interfacial behavior of composites of recycled poly(ethyelene terephthalate) and sugarcane bagasse fiber

This paper reports on a study of composites of recycled poly(ethylene terephthalate) (PETr) and sugarcane bagasse fiber with and without compatibilizing agents. The interfacial behavior of these composites was investigated by torque rheometry, tensile tests, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). A comparison of the torque values resulting from the use of ethylene/n-butyl acrylate/glycidyl methacrylate (EBGMA) and ethylene–methyl acrylate (EMA) copolymer compatibilizing agents indicated that EBGMA increased the interaction between the constituents more effectively than EMA. The addition of bagasse sugarcane fiber did not affect the tensile modulus and reduced the tensile strength and elongation of PETr, as is normally observed in these types of composites. Consistent with the results of torque rheometry and DMA, the SEM analyses indicated that EBGMA improved adhesion between the constituents. All the composites showed promise as good alternatives for the production of environmentally friendly products.     

单电子转移活性自由基聚合制备支化聚丙烯酸甲酯的研究

以丙烯酸2-(2-溴异丁酰氧基)乙酯(BIEA)为引发剂单体(inimer),丙烯酸甲酯(MA)为单体,Cu0/CuBr2和N,N,N',N″,N″-五甲基二亚乙基三胺(PMDETA)为催化体系,二甲亚砜(DMSO)为溶剂,在常温(25℃)下通过单电子转移活性自由基聚合(SET-LRP)合成支化聚丙烯酸甲酯.聚合反应过程中,采用气相色谱(GC)、核磁共振(1H-NMR)和三检测体积排除色谱(TD-SEC)等测试手段跟踪分析和表征支化聚合物的结构.研究结果表明,采用SET-LRP方法,铜粉作为催化剂,常温下聚合反应就能快速进行,130 min之内MA的转化率已达99%以上,制备出高分子量支化聚合物.随着反应的不断进行,聚合物支化程度不断提高,相比较同分子量下的线型聚合物其黏度不断下降,Mark-Houwink特征常数α最小可达0.290.此外,低分子量聚合物组分随着反应不断减少,在高单体转化率下,聚合体系中以高支化度的聚丙烯酸甲酯为主.     

Poly（acrylonitrile-co-3-aminocarbonyl-3-butenoic acid methyl ester）： A better precursor material for carbon fiber than acrylonitrile terpolymer

In order to improve the stabilization and spinnability of polyacrylonitrile, a bifunctional comonomer containing both ester and amide groups was synthesized to prepare poly（acrylonitrile-co-3- aminocarbonyl-3-butenoic acid methyl ester） [P（AN-co-ABM）] copolymers used as the carbon fiber precursor instead of poly（acrylonitrile-acrylamide-methyl acrylate） [P（AN-AM-MA）] terpolymer. The differential scanning calorimetry and thermogravimetry results show that the stabilization of P（AN-co- ABM） have been remarkably improved by ABM compared with P（AN-AM-MA） terpolymer, such as lower initiation temperature, broadened exothermic peak and smaller activation energy. Moreover, the spinnability of P（AN-co-ABM） is also improved by ABM due to the lubrication of ester groups in ABM. This study clearly shows that P（AN-co-ABM） copolymer is a better material for use as a carbon fiber precursor than P（AN-AM-MA） terpolymer.     

Stereoregularity of radically polymerized poly(alkyl acrylates) and poly(trimethylsilyl acrylates) and the preparation of syndiotactic poly(methyl acrylate)

Nuclear magnetic resonance (NMR) spectroscopy was used to determine the stereoregularity of radically polymerized poly(ethyl acrylates), poly(trimethylsilyl acrylates), and poly(isopropyl acrylate-α,β-d₂). The ethyl acrylate polymers consisted of a random configuration having about 50% of isotactic diads, and their stereoregularities were independent of the polymerization temperature (40 to ?78°C). Poly(trimethylsilyl acrylates) and poly(isopropyl acrylate-α,β-d₂) prepared at low temperatures had a syndiotactic configuration. Syndiotactic poly(methyl acrylate) was derived from syndiotactic poly(trimethylsilyl acrylate). For poly(methyl acrylate), an approximate estimation of the stereoregularity by infrared spectroscopy was proposed.     

Upper critical solution temperature switchable micelles based on polystyrene‐block‐poly(methyl acrylate) block copolymers

The solubility behavior of well‐defined poly(methyl acrylate) homopolymers as well as polystyrene‐block‐poly (methyl acrylate) block copolymers is discussed in this contribution. A solubility screening in ethanol–water solvent mixtures was performed in a high‐throughput manner using parallel turbidimetry revealing upper critical solution temperature behavior for poly(methyl acrylate). Moreover, the self‐assembly behavior of the block copolymers into micellar structures was investigated by dynamic light scattering (DLS), transmission electron microscopy (TEM), and cryo‐TEM revealing upper critical solution temperature switchability of the micelles, which was evaluated by DLS at different temperatures. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Design,synthesis, and characterization of a partially chlorinated acrylic copolymer for low‐loss and thermally stable graded index plastic optical fibers

As a novel material of low loss and high thermal stability, a graded index plastic optical fiber (GI POF) comprised of a copolymer of methyl α‐chloro acrylate (MCA) and 2,2,2‐trichloroethyl methacrylate (TCEMA) was prepared and the thermal, mechanical, and optical characteristics were investigated. Although each homopolymer had low loss and desirable high thermal stability, they had crucial disadvantages for the fiber fabrication process. To draw a MCA polymer (PMCA) fiber, it has to be heated above 270 °C. However, the polymer started to decompose at a lower temperature and produced numerous bubbles. In contrast, TCEMA polymer (PTCEMA) is too brittle to roll up during heat drawing. In this study, we succeeded to improve the strong viscoelasticity and the low decomposition temperature of PMCA and the brittleness of PTCEMA by copolymerizing MCA and TCEMA. In addition, the glass transition temperatures (T_g) of the copolymers were in the range of 133–147 °C and the transmittances of the copolymers were much higher than that of PMMA which has been commonly used as a base material of POF. A suitable GI POF was obtained using the MCA and TCEMA copolymer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3352–3361, 2009     

Stereoregularity of poly(methyl acrylate)

The stereoregularity of poly(methyl acrylate) and poly(methyl acrylate-αd) was determined from the NMR spectra. A method of quantitative determination of stereoregularity of poly(methyl acrylate) proposed in this paper is based on the fact that in the 100 Mc./sec. NMR spectrum the absorption peaks due to methylene protons in syndiotactic configurations overlap absorptions due to only one of two methylene protons in isotactic configurations. The stereostructure of poly(methy1 acrylates) polymerized with anionic catalysts such as Grignard reagents, n-butyllithium, and LiAlH₄ is generally richer in isotactic diads than in syndiotactic diads. For example, poly(methyl acrylate) polymerized with phenylmagnesium bromide as catalyst at ?20°C. consists of 99% isotactic and 1% syndiotactic diads. In radical polymerization, the isotacticity of poly(methyl acrylate) is independent of polymerization temperature. Poly(methyl acrylates) polymerized with a Ziegler-Natta catalyst consisting of Al(C₂H₅)₂Cl and VCl₄ have configurations similar to those polymerized by radical initiators. The stereoregularity of poly(methyl acrylate-α-d) resembled that of poly(methyl acrylate) polymerized under the same conditions.     

Patterning on nonplanar substrates: flexible honeycomb films from a range of self-assembling star copolymers

The effect of glass transition temperature, Tg, on the self-assembly of "honeycomb" microstructures on nonplanar substrates was probed by the synthesis of a library of core cross-linked star polymers with different arm compositions. Star polymers based on poly(dimethyl siloxane), poly(ethyl acrylate), poly(methyl acrylate), poly(tert-butyl acrylate), and poly(methyl methacrylate) were synthesized by the "arm first" strategy using atom-transfer radical polymerization. Reaction conditions were optimized, and a series of high molecular weight star polymers were prepared in high yield. The glass transition temperature of the star polymers ranged from -123 to 100 degrees C which allowed the suitability for the formation of porous honeycomb-like films via the "breath figure" technique on nonplanar surfaces to be investigated. All star compositions successfully formed ordered films on flat surfaces. However, only star polymer compositions with a Tg below 48 degrees C could form homogeneous honeycomb coatings on the surface of nonplanar substrates.     

电极界面缓冲层对P3HT:PC61BM太阳能电池热稳定性的影响

基于溶液法加工制备的聚合物太阳能电池的高温热稳定性是决定器件能否兼容后续高温热封装工艺, 如热压封装、高温原子层沉积(ALD)等的一个关键. 本文分别利用聚(3, 4-乙烯二氧噻吩)-聚苯乙烯磺酸(PEDOT:PSS)和MoO₃作为阳极缓冲层, 以及ZnO和LiF 作为阴极缓冲层, 制备了结构为氧化铟锡(ITO)/阳极缓冲层/3-己基取代聚噻吩:(6, 6)-苯基C₆₁-丁酸甲酯(P3HT:PC₆₁BM)/阴极缓冲层/Al 的太阳能电池, 系统地比较研究了不同界面缓冲材料对器件光电转换性能及稳定性的影响, 特别是在高温煺火条件下器件的性能稳定性差异. 结果表明, 聚合物太阳能电池的热稳定性同器件的结构以及所用的缓冲层材料有密切的相关性. 其中, 利用MoO₃及ZnO分别作为阳极与阴极界面修饰层的P3HT:PC₆₁BM器件在120-150 ℃的温度范围内能够较好地保持器件的光电转换性能. 这一结果为后续需要高温封装工艺的器件提供了有意义的结构优化指导. 此外, 研究结果还表明利用ZnO作为阴极缓冲层能够改善器件的长时间稳定性.     

Miscibility of Halogen-containing Polymethacrylates with Various Poly(alkyl acrylate)s

The miscibility behavior of a series of halogen-containing polymethacrylates with poly(methyl acrylate), poly(ethyl acrylate), poly(n-propyl acrylate) and poly(n-butyl acrylate) was investigated by differential scanning calorimetry and for lower critical solution temperature (LCST) behavior. Poly(chloromethyl methacrylate), poly(1-chloroethyl methacrylate), poly(2-chloroethyl methacrylate), poly(2,2-dichloroethyl methacrylate), poly(2,2,2-trichloroethyl methacrylate), poly(2-fluoroethyl methacrylate) and poly(1,3-difluoroisopropyl methacrylate) are miscible with some of the poly(alkyl acrylate)s. Most of the miscible blends show LCST behavior. However, poly(3-choloropropyl methacrylate), poly(3-fluoropropyl methacrylate), poly(4-fluorobutyl methacrylate), poly(1,1,1,3,3,3-hexafluoroisopropyl methacrylate), poly(2-bromoethyl methacrylate) and poly(2-iodoethyl methacrylate) are immiscible with any of the poly(alkyl acrylate)s studied. © 1997 John Wiley & Sons, Ltd.     

Thermal degradation of copolymers of methyl methacrylate and methyl acrylate. I. Products and general characteristics of the reaction

The technique of thermal volatilization analysis (TVA), applied to methyl methacrylate–methyl acrylate copolymers having molar composition ratios 112/1, 26/1, 7.7/1, and 2/1, has demonstrated that the stabilization of poly(methyl methacrylate) by copolymerized methyl acrylate is due to inhibition of the depolymerization initiated at terminally unsaturated structures, probably by direct blockage by methyl acrylate units. The molecular weight of the copolymers decreases rapidly during degradation, suggesting that a random scission process is involved. The products of degradation consist of the monomers, carbon dioxide, chain fragments larger than monomer, and a permanent gas fraction which is principally hydrogen. Infrared and ultraviolet spectral measurements suggest that the residual polymer, which is colored, incorporates carbon–carbon unsaturation. The complete absence of methanol among the products is surprising in view of its abundance among the products of degradation of poly(methyl acrylate). These observations have been accounted for qualitatively in terms of acceptable polymer behavior.     

Pyrolysis of poly(2-propylheptyl acrylate)

The thermal destruction processes of poly(2-propylheptyl acrylate) take place at the range of temperature 250–950 °C was investigated using pyrolysis–gas chromatography. Knowledge of the types and amounts of pyrolysis products will provide important information about the thermal degradation of homopolymer poly(2-propylheptyl acrylate) and the mechanisms involved. Unsaturated monomers 2-propylheptyl acrylate and 2-propylheptyl methacrylate, according to by-product alkyl alcohol 2-propylheptylalcohol, alkene 2-propylheptene-1, carbon dioxide, carbon monoxide, methane, and ethane were formed during thermal degradation of poly(2-propylheptyl acrylate).