Efficient iodine-free dye-sensitized solar cells employing truxene-based organic dyes

Two new truxene-based organic sensitizers (M15 and M16) featuring high extinction coefficients were synthesized for dye-sensitized solar cells employing cobalt electrolyte. The M16-sensitized device displays a 7.6% efficiency at an irradiation of AM1.5 full sunlight.     

Improved charge transport in dye-sensitized solar cells employing viscous non-volatile electrolytes

Dye-sensitized solar cells (DSSCs) employing a viscous non-volatile electrolyte were prepared by utilizing anatase TiO₂ nanorods (synthesized via oriented attachment) as a photoanode material. One promising way to enhance the photovoltaic performance of DSSCs employing viscous electrolytes is to increase ion conductivity by increasing the salt concentration. This is accompanied by an acceleration of the charge recombination reaction and the limiting of the overall conversion efficiency. The results showed that a TiO₂ nanorod electrode enables more favorable electron transport than a conventional nanoparticle-based electrode due to the improved electron diffusion length and the large intrinsic surface area.     

Dye-sensitized solar cells employing amphiphilic poly(ethylene glycol) electrolytes

Poly(ethylene glycol) (PEG) was modified with a long alkyl acid to produce a self-organized amphiphilic polymer (amPEG). FT-IR and NMR spectroscopies confirmed the amPEG synthesis. This polymer was complexed with lithium iodide (LiI) and 1-methyl-3-propylimidazolium iodide (MPII) to prepare polymer electrolytes to be applied to dye-sensitized solar cells (DSSC). FT-IR studies showed that upon the addition of litium salt the free ether and ester carbonyl bands shifted towards lower wavenumbers, indicating the complexation of Li ions with oxygens on the amPEG. Alkylation and salt introduction reduced PEG crystallinity, as characterized by wide angle X-ray scattering (WAXS) and differential scanning calorimetry (DSC). The ionic conductivities of the polymer electrolytes increased with increasing salt concentrations, and the energy conversion efficiency of DSSC reached 2.6% at 100 mW cm^?2 for amPEG/MPII system which is higher than amPEG/LiI. This may be due to the higher mobility of MPII ion than the lithium ion in the polymer electrolyte. The interfacial properties between electrolytes and electrodes were investigated using field-emission scanning electron microscopy (FE-SEM) and electrochemical impedance spectroscopy (EIS).     

Spark source mass spectrometry of silicon for solar cells

Summary Spark source mass spectrometry (SSMS) is used to analyze metallurgical grade silicon powder which has been submitted to different purification steps. The principal advantage of this method in comparison to other analytical methods is the broad range of impurity elements detected simultaneously in each analysis. The silicon powder is mixed with gallium in a weight-ratio of 51 and pressed in a moulding die to solid rods. Detection limits are in the range of 0.02–1 ppma with the exception of some few elements contained in the gallium or introduced during sample preparation. By using self-prepared standards relative sensitivity factors for 35 impurity elements have been determined to enhance the accuracy of the results. Concentration values for most elements are expected to be accurate within a factor of 2. As an example the results of SSMS-measurements referring to one special purification step (acid-treatment) are shown.This paper was originally presented at the 1980 Spring Meeting of The Electrochemical Society, held in St. Louis, Missouri     

Quantum dot-sensitized solar cells employing Pt/C60 counter electrode provide an efficiency exceeding 2%

A microporous platinum/fullerenes (Pt/C 60) counter electrode was prepared by using a facile rapid thermal decomposition method,and the quantum-dot sensitized solar cell (QDSSC) of Pt/C 60-TiO 2-CdS-ZnS and Pt/C 60-TiO 2-CdTe-ZnS was fabrication.The technique forms a good contact between QDs and TiO 2 films.The photovoltaic performances of the as-prepared cells were investigated.The QDSSCs with Pt/C 60 counter electrode show high power conversion efficiency of 1.90% and 2.06%,respectively (under irradiation of a simulated solar light with an intensity of 100 mW cm 2),which is comparable to the one fabricated using conventional Pt electrode.     

Kinetic competition in flexible dye sensitised solar cells employing a series of polymer electrolytes

Transient absorption spectroscopy is employed to study electron transfer dynamics in dye sensitised solar cells employing a series of polymer electrolytes, and correlated with device current-voltage characteristics.     

Chemical etching of zinc oxide for thin-film silicon solar cells

Chemical etching is widely applied to texture the surface of sputter-deposited zinc oxide for light scattering in thin-film silicon solar cells. Based on experimental findings from the literature and our own results we propose a model that explains the etching behavior of ZnO depending on the structural material properties and etching agent. All grain boundaries are prone to be etched to a certain threshold, that is defined by the deposition conditions and etching solution. Additionally, several approaches to modify the etching behavior through special preparation and etching steps are provided.     

Controlled microparticle manipulation employing low frequency alternating electric fields in an array of insulators

Low frequency alternating current insulator-based dielectrophoresis is a novel technique that allows for highly controlled manipulation of particles. By varying the shape of an AC voltage applied across a microchannel containing an array of insulating cylindrical structures it was possible to concentrate and immobilize microparticles in bands; and then, move the bands of particles to a different location. Mathematical modeling was performed to analyze the distribution of the electric field and electric field gradient as function of the shape of the AC applied potential, employing frequencies in the 0.2-1.25 Hz range. Three different signals were tested: sinusoidal, half sinusoidal and sawtooth. Experimental results demonstrated that this novel dielectrophoretic mode allows highly controlled particle manipulation.     

Improved performance in dye-sensitized solar cells employing TiO2 photoelectrodes coated with metal hydroxides

The performance of dye-sensitized solar cells (DSCs) was compared before and after processing the TiO(2) electrodes by minute-order electrochemical reactions with metal nitrates, where the metals were Mg, Zn, Al, and La, in 2-propanol. An overcoating of metal hydroxide was formed without the need for a sintering process, and magnesium hydroxide was found to give the largest improvement in photovoltage, fill factor, and eventually overall conversion efficiency of the DSCs. To analyze the nature of the improvement, the diffusion coefficient (D) and electron lifetime (tau) were determined. While little influence of overcoating on D was seen, a correlation between the increase in tau and V(oc) was observed for the metals examined here. The remarkable improvement in the electron lifetime of the DSCs suggests that an overcoating with magnesium hydroxide species function as the blocking layers at the fluorine-doped tin oxide and TiO(2) interfaces, thus contributing to the suppression of electron leakage, i.e., recombination processes between unidirectional transporting electrons and poly-iodides such as tri-iodide in the processed TiO(2) photoelectrode systems. The increase in V(oc) can be explained by the increased electron density caused by the increase in electron lifetime.     

Calculation of the Helmholtz potential of an elastic strand in an external electric field

We derive from statistical mechanics the Gibbs free energy of an elastic random-walk chain affected by the presence of an external electric field. Intrachain charge interactions are ignored. In addition, we find two approximations of the Helmholtz potential for this system analogous to the gaussian and Cohen-Pade? approximations for an elastic strand without the presence of an electric field. Our expressions agree well with exact numerical calculations of the potential in a wide range of conditions. Our analog of the gaussian approximation exhibits distortion of the monomer density due to the presence of the electric field, and our analog of the Cohen-Pade? approximation additionally includes finite chain extensibility effects. The Helmholtz potential may be used in modeling the dynamics of electrophoresis experiments.     

Modifying the morphology via employing rigid phenyl side chains achieves efficient nonfullerene polymer solar cells

As a promising electron-deficient (acceptor) unit, fluorinated benzotriazole (TAZ) was used widely to construct wide bandgap polymers for nonfullerene polymer solar cells (NF-PSCs). However, due to the S…F noncovalent interaction, the unit show good planarity and strong aggregation, which was not beneficial for the blend with the elongated nonfullerene acceptors. Here, we tried to choose new donor polymers to match with TAZ unit, which was expected to destroy the interchain aggregation of polymer and form favorable morphology of blends. Two new wide-bandgap polymers PBDTsPhPh-T1 and PBDTsThPh-T1 based on the unsymmetrical benzodithiophene (BDT) units with a benzene ring as lever arms were synthesized. As a result, these two polymers blend well with nonfullerene acceptor (ITIC). And then, PBDTsPhPh-T1 and PBDTsThPh-T1-based devices exhibit the decent photovoltaic properties with high power conversion efficiencies of 8.85 and 9.34%, respectively. The work demonstrates that the unsymmetrical BDT units could be outstanding for building donor materials toward high-performance NF-PSCs. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2762–2770     

Efficient perovskite solar cells employing a solution-processable copper phthalocyanine as a hole-transporting material

The development of alternative low-cost and high-performing hole-transporting materials(HTMs) is of great significance for the potential large-scale application of perovskite solar cells(PSCs) in the future.Here,a facilely synthesized solution-processable copper tetra-(2,4-dimethyl-3-pentoxy) phthalocyanine(CuPc-DMP) via only two simple steps,has been incorporated as a hole-transporting material(HTM) in mesoscopic perovskite solar cells(PSCs).The optimized devices based on such a HTM afford a very competitive power conversion efficiency(PCE) of up to 17.1%measured at 100 mW cm~(-2) AM 1.5G irradiation,which is on par with that of the well-known 2,2',7,7'-tetrakis(N'N'-di-p-methoxyphenylamine)-9,9'-spirobifluorene(spiro-OMeTAD)(16.7%) under equivalent conditions.This is,to the best of our knowledge,the highest value reported so far for metal organic complex-based HTMs in PSCs.The advantages of this HTM observed,such as facile synthetic procedure,superior hole transport characteristic,high photovoltaic performance together with the feasibility of tailoring the molecular structure would make solution-processable copper phthalocyanines as a class of promising HTM that can be further explored in PSCs.The present finding highlights the potential application of solution processed metal organic complexes as HTMs for cost-effective and high-performing PSCs.     

Problems in the melt- and vapor growth of silicon for integrated circuits and solar cells

Since the invention of the transistor in 1948 silicon has emerged as the most versatile semiconductor material, and the resulting devices have caused a revolution in the electronics industry. The crystal growth of silicon from the melt is the basis for the nearly perfect crystalline quality needed for the devices. Problems in the melt growth, the elimination of dislocations, and the prevention of the precipitation of point defects are still under study and are discussed. In addition, the growth of thin monocrystalline layers of Si on a monocrystalline substrate has become of great importance. In sharp contrast to this type of approach are the recent activities aimed at obtaining cheap silicon photovoltaic solar cells. Examples of methods based on melt or vapor growth for producing thin, almost monocrystalline layers on a cheap substrate are given. The new discovery that amorphous silicon may be a suitable candidate for this type of cells is discussed.     

Personal solar UV exposure measurements employing modified polysulphone with an extended dynamic range

Polysulphone dosimeters using a simple to use filter have been developed and tested to provide an extended dynamic measurement range of personal solar UV exposures over an extended period (3 to 6 days). At a Southern Hemisphere subtropical site (27.6 degrees S, 151.9 degrees E), the dynamic range of the filtered polysulphone allowed measurements of erythemal exposures to approximately 100 minimum erythemal dose (MED) for a change in optical absorbance at 330 nm (deltaA330) of 0.35. In comparison, unfiltered polysulphone dosimeters were exposed to approximately 8 MED for the same deltaA330. The error associated with the use of the filtered polysulphone dosimeters is of the order of +/-15%, compared with +/-10% of the unfiltered variety. The developed filtered polysulphone dosimeter system allowed the measurement of erythemal UV exposures over 3 to 6 days at a subtropical site without the need to replace the dosimeters because of saturation. The results show that longer-term measurement programs of personal solar UV have been made more feasible with the use of these polysulphone dosimeters with an extended dynamic range compared with unfiltered polysulphone dosimeters.     

Comparison of solar silicon feedstock

One of the major factors in reducing a cost of commercial solar cells is the lifetime of the photovoltaic material. In this work, a deterioration of Si generated by solvent metal gathering method (SMG) and Si removed from damaged solar cells is analyzed and compared with electronic grade Si. The differences in heating and cooling cycles on the DTA curves of different solar grade Si and Cu–Si mixtures are compared. A nonequilibrium exothermic reaction in Si generated by SMG method is recorded in samples aged in room atmosphere for 1 year. The outcomes of the cooling cycles after the DTA analyses for various solar grades Si were not significantly differentiated from the referred electronic grade Si indicating that recrystallization of aged Si diminishes the problem related to agglomeration of Cu and oxygen on the surface of Si solar grade particles. The DTA tests showed that recrystallized Si from the deteriorated solar cells can be recycled as feedstock materials for solar cells applications while Si generated by SMG method can be used for blending in order to achieve a long lifetime of Si solar cells.     

SnSe2 quantum dot sensitized solar cells prepared employing molecular metal chalcogenide as precursors

A kind of molecular metal chalcogenide, (N(2)H(4))(3)(N(2)H(5))(4)Sn(2)Se(6) complex, was synthesized in the hydrazine solution and employed as the precursors for SnSe(2) deposition on TiO(2) nanocrystalline porous films. A power conversion efficiency of 0.12% under AM 1.5, 1 sun was obtained for the SnSe(2) sensitized TiO(2) solar cells.     

Charge transport versus recombination in dye-sensitized solar cells employing nanocrystalline TiO2 and SnO2 films

We report a comparison of charge transport and recombination dynamics in dye-sensitized solar cells (DSSCs) employing nanocrystalline TiO(2) and SnO(2) films and address the impact of these dynamics upon photovoltaic device efficiency. Transient photovoltage studies of electron transport in the metal oxide film are correlated with transient absorption studies of electron recombination with both oxidized sensitizer dyes and the redox couple. For all three processes, the dynamics are observed to be 2-3 orders of magnitude faster for the SnO(2) electrode. The origins of these faster dynamics are addressed by studies correlating the electron recombination dynamics to dye cations with chronoamperometric studies of film electron density. These studies indicate that the faster recombination dynamics for the SnO(2) electrodes result both from a 100-fold higher electron diffusion constant at matched electron densities, consistent with a lower trap density for this metal oxide relative to TiO(2), and from a 300 mV positive shift of the SnO(2) conduction band/trap states density of states relative to TiO(2). The faster recombination to the redox couple results in an increased dark current for DSSCs employing SnO(2) films, limiting the device open-circuit voltage. The faster recombination dynamics to the dye cation result in a significant reduction in the efficiency of regeneration of the dye ground state by the redox couple, as confirmed by transient absorption studies of this reaction, and in a loss of device short-circuit current and fill factor. The importance of this loss pathway was confirmed by nonideal diode equation analyses of device current-voltage data. The addition of MgO blocking layers is shown to be effective at reducing recombination losses to the redox electrolyte but is found to be unable to retard recombination dynamics to the dye cation sufficiently to allow efficient dye regeneration without resulting in concomitant losses of electron injection efficiency. We conclude that such a large acceleration of electron dynamics within the metal oxide films of DSSCs may in general be detrimental to device efficiency due to the limited rate of dye regeneration by the redox couple and discuss the implications of this conclusion for strategies to optimize device performance.     

Water soluble amino grafted silicon nanoparticles and their use in polymer solar cells

Stable aqueous amino-grafted silicon nanoparticles(SiNPs-NH2) were prepared via one-pot solution method. By grafting amino groups on the particle surface, the dispersion of SiNPs in water became very stable and clear aqueous solutions could be obtained. By incorporating SiNPs-NH2 into the hole transport layer of poly(3,4-ethylenedioxythiophene)/polystyrene sulfonic acid(PEDOT:PSS), the performance of polymer solar cells composed of poly[2-methoxy,5-(2'-ethylhexyloxy)-1,4-phenylene vinylene](MEH-PPV):[6,6]-phenyl-C61-butyric acid methyl ester(PCBM) as active layer can be improved. SiNPs-NH2 are dispersed uniformly in the PEDOT:PSS solution and help form morphologies with small-sized domains in the PEDOT:PSS film. SiNPs-NH2 serve as screens between conducting polymer PEDOT and ionomer PSS to improve the phase separation and charge transport of the hole transport layer. As a result, the sheet resistance of PEDOT:PSS thin films is decreased from(93 ± 5) × 105 to(13 ± 3) × 105 ?/□. The power conversion efficiency(PCE) of polymer solar cells was thus improved by 9.8% for devices fabricated with PEDOT:PSS containing 1 wt% of SiNPs-NH2, compared with the devices fabricated by original PEDOT:PSS.