Solid phase extraction and spectrophotometric determination of mercury by adsorption of its diphenylthiocarbazone complex on an alumina column

A simple method has been developed for the preconcentration of mercury based on the adsorption of its diphenylthiocarbazone complex on a neutral alumina column. The influence of acidity, eluting agents, stability of the column, sample volume and interfering ions has been investigated in detail. The adsorbed complex could be eluted using environmentally benign polyethylene glycol (PEG 400) and the concentration of mercury was determined by visible spectrophotometry at a wavelength maximum of 520nm. A detection limit of 4microgL(-1) could be achieved and the developed procedure was successfully applied for the determination of mercury in spiked water samples and city waste incineration ash (CRM176). The preconcentration factor attainable for quantitative recovery (>95%) of mercury(II) was 100 for a 1000mL sample volume.     

Efficient adsorption of uranium (VI) from aqueous solution by a novel modified steel slag adsorbent

Journal of Radioanalytical and Nuclear Chemistry - Using steel slag as a raw material, a new type of adsorption material has been prepared by acid modification method. The preparation conditions of...     

Selective solid phase extraction of palladium by adsorption of its 5(p-dimethylaminobenzylidene)rhodanine complex on silica-PEG as a new adsorbent

The nickel(II) complex of a deoxyribonucleic acid (DNA-Ni²⁺) was directly electrodeposited on the surface of a glassy carbon electrode (GCE) to give a DNA-Ni/GCE electrode. It was investigated in terms of its capability of electro-oxidizing methanol in alkaline medium. It exhibits stable redox behavior of the Ni²⁺/Ni³⁺ couple by cyclic voltammetry. The DNA-Ni²⁺ membrane showed excellent electrocatalytic suitability for the electro-oxidation of methanol, is stable and responds reproducibly. The linear range for the detection of methanol in alkaline medium is from 8.0 µM to 2.4 mM, and the limit of detection is 2.0 µM (at a signal-to-noise ratio of 3).     

The extraction of chromium(VI) from sulphuric acid solutions by 4-(5-nonyl)pyridine and its separation from fission products

4-(5-Nonyl)pyridine, a new liquid anion exchanger, has been studied for the extraction of chromium(VI) from sulphuric acid solutions. The optimal acidity is 0.1–1 M, depending on the concentration of chromium. Common anions have little effect on extraction in concentrations up to 0.1 M. Reducing agents such as ascorbic acid and thiosulphate prevent extraction at concentrations above 0.1 M. Separation of chromium(VI) from fission products was achieved.     

Kinetics of chromium(VI) adsorption from model solutions on iron oxide

Adsorption of Cr(VI) on Fe₂O₃ from model solutions with various Cr(VI) concentrations was studied. The adsorption capacity was determined, the constants of chromium(VI) adsorption on iron(III) oxide for the pseudo-second-order model were calculated, and the diffusion coefficients for the process were evaluated.     

Indirect spectrophotometric determination of traces of antimony(III) based on its oxidation by chromium(VI) and reaction of chromium(VI) with diphenylcarbazide

An indirect method for the determination of antimony(III) is described. Antimony(III) is oxidized to antimony(V) by chromium(VI) and the excess of chromium(VI) is then determined spectrophotometrically with diphenylcarbazide. Optimal conditions were established for both the determination of antimony(III) and the elimination or reduction of interferences. Antimony(III) can be determined quickly and easily in the range 0.05–5 mg l^?1; the relative standard deviation is 2% for 1.0 mg l^?1 antimony(III). The method is applicable to marine sediments and geothermal waters.     

Removal of copper from aqueous solutions by adsorption on activated carbons

The adsorption isotherms of Cu(II) ions from aqueous solutions in the concentration range 40–1000 mg l⁻¹ on two samples of granulated and two samples of activated carbon fibres containing varying amounts of associated oxygen have been reported. The adsorption isotherms are type I of BET classification showing initially a rapid adsorption tending to be asymptotic at higher concentrations. The amounts of oxygen associated with the carbon surface has been enhanced by oxidation with nitric acid and ammonium persulphate in the solution phase and with oxygen gas at 350°C and decreased by degassing of the oxidized carbon samples at 400, 650 and 950°C. The adsorption of Cu(II) ions increases on oxidation and decreases on degassing. The increase in adsorption on oxidation depends on the nature of the oxidative treatment while the decrease in adsorption on degassing depends on the temperature of degassing. This has been attributed to the increase in the carbon–oxygen acidic surface groups on oxidation and their decrease on degassing. Suitable mechanisms consistent with the results have been proposed.     

Ion exchange recovery of chromium (VI) and manganese (II) from aqueous solutions

Sorption recovery of toxic ions – chromium (VI) and manganese (II) – from aqueous solutions with different acidity (0.001–0.5 M HCl) was investigated on cation and anion exchangers synthesized with long-chained cross-linking agents (LCA). The initial concentrations of Cr(VI) and Mn(II) were 1 g/L and 5 g/L, respectively. It was shown that the resins with LCA possess high ionic permeability due to the elasticity of polymeric skeleton. High selectivity and good kinetic properties of these sorbents allowed to achieve quantitative (∼100%) recovery and separation of manganese (II) and chromium (VI) in counter-current columns, which results in the complete purification of solutions from toxicants (below the maximum permissible limits), whereas the valuable components (chromium and manganese) can be returned back to industrial process.     

Hydrogen peroxide interference in the determination of chromium(VI) by the diphenylcarbazide method

Hydrogen peroxide at concentrations ?10^?5 mol l^?1 interferes in the spectrophotometric determination of chromium(VI) with dephenylcarbazide, because Cr(VI) is reduced to Cr(III) in acidic conditions. The interference depends on the H₂O₂ concentration and on the standing time between the additions of acid and diphenylcarbazide, and can be avoided (for ?0.4 mmol l^?1 H₂O₂) by adding a larger amount of reagent before the acid. The latter observation suggests that storage of samples under acidic conditions could cause a decrease in Cr(VI) concentration.     

Methanol and ethanol oxidation by chromium(VI) in aqueous perchloric acid

Summary Oxidation of short-chain alcohols (MeOH and EtOH) by Cr^VI in concentrated aqueous HClO₄ does not fit pseudo-first order rate equations, but results can be expressed in a two-exponential equation. A reaction mechanism based upon a chromate ester intermediate in equilibrium with the protonated alcohol and the chromic acid, suitable for a longer chain alcohol, does not account for kinetic results. A new mechanism is considered involving an intermediate reaction between chromic and perchloric acids.     

Uranium(VI) removal from aqueous solutions by a chelating fiber

Journal of Radioanalytical and Nuclear Chemistry - A chelating fiber (CF), containing amine and hydroxyl groups, has been characterized and used as an adsorbent for the removal of U(VI) from...     

Solid phase extraction of chromium(VI) using Aliquat336 immobilized on a thin film of multiwall carbon nanotubes

We report on a novel and selective method for the preconcentration and determination of Cr(VI) in aqueous samples. Cr(VI) is adsorbed - in a “batch mode” - on multiwalled carbon nanotubes covered with Aliquat 336 and then determined directly, i.e., on the solid, by X-ray fluorescence spectrometry. This reduces the number of reagents and minimizes sample handling. The method combines the advantages of solid-phase extraction with the benefits of the XRF method in that the large areas required by the carbon nanotubes make them a promising solid sorbent for preconcentration. The enrichment factor was calculated after considering that the thin film obtained from the 10?mL solution of 1?mg?L^?1 of Cr(VI) has a real thickness of 0.04?mm and a final diameter of 16.7?mm, so that the volume deposited on the pellet is 0.0088 cm³ and the preconcentration factor is 1000.

Preparation of new modified silica gel terminated with phenylphosphonic acid-amide moieties for adsorption of uranium(VI) from aqueous solutions

Journal of Radioanalytical and Nuclear Chemistry - PAMAM dendrimers modified silica gel terminated phenylphosphonic acid-amide moieties (Si-6G PAMAM-PPAAM) was prepared for uranium(VI) adsorption...     

Solid phase extraction using silica gel functionalized with Sulfasalazine for preconcentration of uranium(VI) ions from water samples

Silica gel surface was chemically functionalized by reaction the silanol from the silica surface with 3-chloropropyltrimethoxysilane followed by reaction with Sulfasalazine. This new sorbent has been used for the preconcentration of low levels of U(VI) ions from an aqueous phase. Parameters involved in extraction efficiency such as pH, weight of the sorbent, volume of sample and eluent were optimized in batch and column methods prior to determination by spectrophotometry using arsenazo(III) reagent. The results showed that U(VI) ions can be sorbed at pH range of 5.0–6.0 in a minicolumn and quantitative recovery of U(VI) (>98.0?±?1.6%) was achieved by stripping with 2.5 mL of 0.1 mol L^?1 HCl. The sorption capacity of the functionalized silica gel was 1.15 mmol g^?1 of U(VI). A linear calibration graph was obtained over the concentration range of 0.02–27.0 μg mL^?1 with a limit of detection of 1 μg L^?1 in treatment with 1000 mL of the U(VI) solution in which the preconcentration factor was as high as 400. The method was employed to the preconcentration of U(VI) ions from spiked ground water and synthetic sea water samples.     

Ultrasound-assisted adsorption of Pb ions by carbonized/activated date stones from singles/mixed aqueous solutions

This work aims to assess the adsorption efficiency of date stones biowaste subjected to carbonization and activation processes for the removal of Pb ions from single and mixed solutions. Several techniques have been used for characterization of adsorbents such as scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), methylene blue index and point of zero charge (pHpzc). An excellent adsorption capacity of 97.43% is achieved at an initial concentration of 300 ?mg/L, solution volume 75 ?mL of Pb nitrate, adsorbent mass of 0.7 ?g, temperature of 30 ?°C, a stirring speed of 500 ?rpm/min, a contact time of 180 ?min and pH 6. Specifically, a comparison has been conducted between carbonized/activated date stones “CADS” and commercial activated carbon “CAC” besides investigating the influence of the presence of Co ions and the utilization of ultrasound radiation. A higher adsorption rate of 98.16% is reached under ultrasound radiation at Pb(II) initial concentration of 100 ?mg/L for a contact time of 3 ?h. Nevertheless, the temperature has shown a negative effect; the adsorption rate decreases from 98.31% at 18 ?°C to 92.70% at 60 ?°C. The modeling of the experimental adsorption data manifests a type-L isotherm characteristic of Langmuir and Freundlich models. The kinetic study has shown that the experimental data are well described by a pseudo-second-order rate model and controlled by the internal diffusion, a limiting-step that controls the transfer rate of Pb(II) to the adsorbent surface. The calculated thermodynamic parameters (ΔG⁰, ΔH⁰, ΔS⁰) indicate that the adsorption of Pb(II) is spontaneous and exothermic process.     

Novel chromium(III)/(VI) adducts of XPS-determined mixed valence,from electroreduced chromium(VI)

Summary Conditions of chromium(VI) and acidity have been found at which a novel brown deposit from electroreduction. Its 11 chromium(III):chromium(VI) composition, and the 21 ratio of the alkali-leached product, were established by XPS. The composition bounds for electrodeposition of the 11 solid and the competing insulative chromium(III) film were established electrochemically. Earlier reported chromium(III) and chromium(VI) solid or gels, some deposited from alkali, differ in colour and composition properties.     

Preconcentrative separation of chromium(VI) species from chromium(III) by coprecipitation of its ethyl xanthate complex onto naphthalene

A rapid, sensitive and selective method is described for the determination of chromium(VI) in presence of 100-fold amounts of chromium(III) by flame atomic absorption spectrometry (FAAS) in conjunction with coprecipitative preconcentration of its ethyl xanthate complex onto naphthalene. The solid mixture consisting of the chromium(VI) complex together with naphthalene is dissolved in 8.0 ml of dimethyl formamide (DMF) and chromium(VI) content was established by FAAS. Calibration graphs were rectilinear over the chromium(VI) concentration in the range 0-200 μg l⁻¹. Five replicate determinations of 20 μg of chromium(VI) present in 1.0 l of sample solution gave a relative standard deviation of 3.1%. The detection limit corresponding to three times the standard deviation of the blank was found to be 0.5 μg l⁻¹. The developed procedure has been successfully utilized for the estimation of chromium(VI), chromium(total) (after oxidation with bromate) and chromium(III) (by subtracting chromium(VI) content from chromium(total) value contents of several tannery industries.     

Preparation of Fe-loaded activated carbon and its adsorption property of U(VI) in aqueous solution

Three kinds of method were employed to prepare Fe loaded activated carbon (Fe-AC), liquid reduction method, carbonthermal method, incipient wetness method, respectively. Before and after adsorption, the adsorption property of Fe-AC had been analysed. Results indicated that the removal mechanisms were mainly redox reaction, adsorption and precipitation. In addition, the adsorption models fitted with the kinetic model and adsorption isotherm model. Based on the analysis of six influencing factors, we obtain some actual information to deal with the humic acid and the “back to acid”.     

Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection.

A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both species were detected by use of the luminol-hydrogen peroxide chemiluminescence system. Linear calibration for both species was established over the concentration range 1-1000 micrograms l-1. The precision at the 20 micrograms l-1 level was 3.5% for chromium(iii) and 3.3% for chromium(vi), respectively. The detection limit was 0.5 micrograms l-1 for both species. Data were in agreement with Zeeman-effect background corrected atomic absorption spectrometry measurements.