Surface‐Plasmon‐Coupled Emission of Rhodamine 110 in a Silica Nanolayer

The first observation of strong directional surface‐plasmon‐coupled emission (SPCE) of Rhodamine 110 in silica nanofilms deposited on silver nanolayers is reported. The preparation of the material is described in detail. The intensity of SPCE exceeds 10 times that of free space fluorescence and total linear light polarization in the SPCE ring is observed. A new experimental setup and an original data collection method is presented. Our material completely preserves its fluorescence properties for at least eight months.     

银膜表面等离子体耦合辐射特性的仿真分析

表面等离子体耦合辐射(SPCE)是传统表面等离子体共振(SPR)的逆过程:当分子足够靠近金属薄膜表面时( < 200 nm),其受激辐射的能量可以耦合成SPR模式并定向辐射到棱镜中.由于具有场增强特性、高收集效率和优异的表面选择性, SPCE作为一种新的表面分析技术已经在荧光和拉曼光谱领域得到了有效的应用.本文采用光学互易定理简化传统SPCE的计算方法.通过计算,我们得到了SPCE一维和二维辐射功率密度分布,表面选择性,辐射角的波长色散特性,辐射角半峰宽与银膜厚度的关系.仿真结果与已报到的实验结果吻合良好,验证了该方法的有效性.     

Ag‐CNT Architectures for Attomolar Dopamine Detection and 100‐Fold Fluorescence Enhancements with Cellphone‐Based Surface Plasmon‐Coupled Emission Platform

We report cellphone‐based detection of dopamine with attomolar sensitivity in clinical samples with the use of a surface plasmon‐coupled emission (SPCE) platform. To this end, silver‐coated carbon nanotubes were used as spacer and cavity materials on SPCE substrates to obtain up to 100‐fold fluorescence enhancements. The presence of silver on the carbon nanotubes helped to overcome fluorescence quenching arising due to π–π interactions between the carbon nanotube and rhodamine 6G. The competing adsorption of dopamine versus rhodamine 6G on graphene oxide was utilized to develop this sensing platform.     

Analysis of immunoarrays using a gold grating-based dual mode surface plasmon-coupled emission (SPCE) sensor chip

We have developed a novel dual mode immunoassay platform that combines the advantages of real-time, label free measurement of surface plasmon resonance (SPR) and the highly directional surface plasmon-coupled emission (SPCE) using a gold grating-based sensor chip. Since only fluorophore-labeled analyte molecules that are close to the metal surface of the sensor chip will couple to the surface plasmon, SPCE detection is highly surface-specific leading to background suppression and increased sensitivity. Theoretical calculations were done to find SPR and SPCE angles for a sensor chip optimized for Alexa Fluor 647. We have confirmed the SPR and SPCE responses on the dual mode sensor chip using Alexa Fluor 647 labeled anti-mouse IgG. Signal fluctuation of the dual mode sensor chip reader was below 1.2% and 0.8% for SPR and SPCE, respectively. The SPR response in this configuration showed a minimum detection level of 1 μg ml(-1), and the SPCE response showed a minimum detection level of 1 ng ml(-1) for the same sample. A range of human IgG concentrations in human serum was also analyzed with the dual mode sensor chip. The SPCE measurement is more sensitive than the SPR real-time measurement, and substantially extends the dynamic range of the assay platform, as well as enabling independent measurements of co-localized analytes on the same sensor chip region of interest. Since this assay platform is capable of measuring more than 1000 spatially encoded regions of interest on a 1 cm(2) sensor chip, it has the potential for high-content analyses of biological samples with both research and clinical applications.     

Capillary array isoelectric focusing with laser-induced fluorescence detection: milli-pH unit resolution and yoctomole mass detection limits in a 32-channel system

We report a multiplexed capillary electrophoresis system employing an array of 32 capillaries with a micromachined sheath-flow cuvette as the detection chamber. The sample streams were simultaneously excited with a 473-nm laser beam, and the fluorescence emission was imaged on a CCD camera with a pair of doublet achromat lens. The instrument produced mass detection limits of 380 ± 120 yoctomoles for fluorescein in zone electrophoresis. Capillary isoelectric focusing of fluorescent standards produced peaks with an average width of 0.0029 ± 0.0008 pH. Capillary coating stability limits the reproducibility of the analysis.     

Surface plasmon-coupled polarized emission of N-acetyl-l-tryptophanamide

We report an observation of ultraviolet (UV) surface plasmon-coupled emission (SPCE) of N-acetyl-l-tryptophanamide (NATA). The sample was spin coated from poly(vinyl alcohol) (PVA) solution on 20 nm aluminum film deposited on a quartz substrate. The directional UV SPCE occurs within a well-defined narrow angle at 52 degrees from the normal to the coupling hemicylinder quartz prism. The NATA directional emission is highly p polarized as expected for surface plasmon-coupled radiation. The 10 nm protective SiO2 layer deposited on top of the aluminum film significantly neutralized the fluorophore quenching by the metal surface. SPCE of NATA demonstrates a remarkable intrinsic dispersive property-the maximum of the emission spectrum depends on the observation angle. The efficient spectral resolution of SPCE can be used in the construction of miniaturized spectrofluorometers. The observation of SPCE of tryptophan opens a new possibility for the study of many unlabeled proteins with the technique complementary to surface plasmon resonance analysis.     

Enhanced modulation of magnetic field on surface plasmon coupled emission (SPCE) by magnetic nanoparticles

This article demonstrates the enhancement of magnetic nanoparticles on magnetic field modulation of surface plasmon coupled emission (SPCE), and this method is designed as a biosensor to prove the feasibility of magnetic field modulated SPCE to be employed in the field of biosensing and biodetection.     

Enhanced modulation of magnetic field on surface plasmon coupled emission (SPCE) by magnetic nanoparticles

The obvious enhancement effect of magnetic nanoparticles (MNPs) introduced in Cr/Co/Cr/Au substrate on the pulsed magnetic field-modulated surface plasmon coupled emission (SPCE) was investigated, and the observed enhancement factor was 4 comparing with the magnetic field modulated SPCE without MNPs. This is the new observation for the magnetic field modulated SPCE, and this method was designed as a biosensor, which to our knowledge, is the first application of magnetic field-modulated SPCE in biosensing and detection field. This strategy is a universal approach to increase the fluorescence signal and helps to build the new SPCE based stimulus-response system.     

A reusable liposome array and its application to assay of growth-hormone-related peptides

We describe a reusable liposome array based on the formation of cleavable disulfide cross-links between liposomes and the surface of a glass slip. The N-succinimidyl 3-(2-pyridyldithio)-propionate (SPDP)-modified liposomes encapsulating a pH-sensitive fluorescence dye were immobilized on a 3-mercaptopropyltrimethoxysilane (MTS)-modified glass slip through the formation of disulfide bonds. The regeneration of a used slip was performed by the lysis of immobilized liposomes with Triton X-100 and the cleavage of disulfide bonds by reduction with TCEP, followed by immobilization of SPDP-modified liposomes. The regeneration steps did not affect the fluorescence intensity of re-immobilized liposomes. The liposome array was applied to simultaneous quantification of growth hormone related peptides, i.e., GHRF and somatostatin, in a mixture. After optimizing the assay condition, the method allowed quantification of GHRF and somatostatin in concentration ranges from 0.5 × 10⁻⁹ to 0.5 × 10⁻⁷ g/mL with detection limits of 2 × 10⁻¹⁰ and 3 × 10⁻¹⁰ g/mL, respectively.     

Donor–acceptor nonradiative energy transfer mediated by surface plasmons on ultrathin metallic films

Selected properties of donor–acceptor energy transfer in the presence of surface plasmon coupled emission (SPCE) on metallic nanofilms are demonstrated. These properties of surface plasmon mediated energy transfer (SPMET) are for the first time compared to those of traditional energy transfer (ET) based on the same donor–acceptor system. The presence of plasmons significantly accelerates energy transfer as revealed by the results of fluorescence intensity decay. In particular, the rise time of acceptor fluorescence intensity upon donor excitation is 10 times shorter in the presence of SPCE. It is also observed that contrary to ET the sensibilized acceptor emission in SPMET is totally linearly polarized.     

Surface-plasmon-coupled emission of quantum dots

We studied surface plasmon-coupled emission (SPCE) of semiconductor quantum dots (QDs). These QDs are water-soluble ZnS-capped CdSe nanoparticles stabilized using lysine cross-linked mercaptoundecanoic acid. The QDs were spin-coated from 0.75% PVA solution on a glass slide covered with 50 nm of silver and a 5-nm protective SiO(2) layer. Excited QDs induced surface plasmons in a thin silver layer. Surface plasmons emitted a hollow cone of radiation into an attached hemispherical glass prism at a narrow angle of 48.5 degrees. This directional radiation (SPCE) preserves the spectral properties of QD emission and is highly p-polarized irrespective of the excitation polarization. The SPCE spectrum depends on the observation angle because of the intrinsic dispersive properties of SPCE phenomenon. The remarkable photostability can make QDs superior to organic fluorophores when long exposure to the intense excitation is needed. The nanosize QDs also introduce a roughness near the metal layer, which results in a many-fold increase of the coupling of the incident light to the surface plasmons. This scattered incident illumination transformed into directional, polarized radiation can be used simultaneously with SPCE to develop devices based on both quantum dot emission and light scattered from surface plasmons on a rough surface.     

Red blood cells do not attenuate the SPCE fluorescence in surface assays

We describe the positive effect of surface plasmon-coupled fluorescence emission (SPCE) on the detection of a signal from a surface immunoassay in highly absorbing or/and scattering samples. A model immunoassay using fluorescently labeled anti-rabbit antibodies that bind to rabbit immunoglobulin on a silver surface was performed, and the signal was detected in the presence of various highly absorbing and/or scattering solutions or suspensions, such as hemoglobin solution, plastic beads, and red blood cells. The results showed that a highly absorbing solution consisting of small molecules (dye, hemoglobin) attenuates the SPCE signal approximately 2-3-fold. In contrast, suspensions with the same absorption containing large particles (large beads, red blood cell suspension) attenuate the SPCE signal only slightly, approximately 5-10%. Also, a suspension of large undyed, highly scattering beads does not reduce the SPCE signal. The effects on the immunoassay signal of the sample background absorption and scattering, the size of the background particles, and the geometry of the experimental set-up are discussed. We believe that SPCE is a promising technique in the development of biosensors utilized for surface-based assays, as well as any assays performed directly in highly absorbing and/or scattering solutions without washing or separation procedures. Figure Red blood cells (unlike hemoglobin) do not attenuate the SPCE fluorescence in surface assays.     

Surface plasmon fluorescence investigation of energy-transfer-controllable organic thin films

Thin functional organic films on a gold substrate were fabricated by adsorbing tetrakis(carboxyphenyl)porphyrin (TCPP) on a spacer layer, which was prepared by the layer-by-layer adsorption of a dendrimer and a linear polymer. The thickness and photoluminescence of the films were investigated by surface plasmon resonance and surface plasmon fluorescence techniques, respectively. TCPP adsorbed on the spacer layer in aqueous solutions of different ionic strengths resulted in a thick TCPP adlayer at high ionic strength and a shrunk spacer layer at low ionic strength. The fluorescence was quenched at high ionic strength but could be observed at low ionic strength. The effects are explained by the states of dye aggregation. This study shows the control of energy transfer from a metal surface to a dye layer by changing the dye adlayer. It can contribute to the development of molecular devices involving energy-transfer systems.     

Binding properties of a monoclonal antibody against the Cry1Ab from <Emphasis Type="Italic">Bacillus Thuringensis</Emphasis> for the development of a capillary electrophoresis competitive immunoassay

Experimental work performed was aimed at the assessment of a competitive capillary electrophoresis immunoassay with laser-induced fluorescence (CEIA-LIF) detection for the determination of the Cry1Ab endotoxin from Bacillus thuringensis. The binding constant of a monoclonal antibody, raised against the insecticide protein Cry1Ab, was determined on a microplate by indirect enzyme-linked immunosorbent assay (ELISA) and compared with that obtained in-capillary under nonequilibrium separation conditions. The two binding constants appear comparable—(5.0 ± 1.2) × 10⁶ M⁻¹ and (9.06 ± 5.7) × 10⁶ M⁻¹—reflecting good preservation of the antibody binding behavior in the capillary electrophoresis format. These results allow use of a calibration curve possible between 0.2 and 150 nM of endotoxin protein, with a limit of detection of 0.5 nM (33 μg L⁻¹). Preliminary recovery experiments on maize extracts spiked with known amounts of Cry1Ab endotoxin also showed promising results in detecting the toxin in complex real matrices.     

Part per trillion determination of atrazine in natural water samples by a surface plasmon resonance immunosensor

A new immunoassay for continuously monitoring atrazine in water has been developed. It uses a portable biosensor platform based on surface plasmon resonance (SPR) technology. This immunoassay is based on the binding inhibition format with purified polyclonal antibodies, with the analyte derivative covalently immobilized on a gold sensor surface. An alkanethiol self-assembled monolayer (SAM) was formed on the gold-coated sensor surface in order to obtain a reusable sensing surface. The low detection limit for the optimized assay, calculated as the concentration that produces a 10% decrease in the blank signal, is 20 ng/L. A complete assay cycle, including regeneration, is accomplished in 25 min. Additionally, a study of the matrix effects of different types of wastewater was performed. All measurements were carried out with the SPR sensor system (β-SPR) commercialised by the company Sensia, S.L. (Spain). The small size and low response time of the β-SPR platform would allow it to be used in real contaminated locations. The immunosensor was evaluated and validated by measuring the atrazine content of 26 natural samples collected from Ebro River. Solid-phase extraction followed by gas chromatography coupled to mass spectrometric detection (SPE–GC–MS) was used to validate the new immunoassay.     

Fluorescence polarization immunoassay for rapid screening of ochratoxin A in red wine

A fluorescence polarization (FP) immunoassay, based on a monoclonal antibody and an ochratoxin A (OTA)-fluorescein tracer, has been developed for rapid screening of OTA in red wine. Wine samples were diluted with methanol and passed through aminopropyl solid-phase extraction columns prior to the FP assay. Average recoveries from samples spiked with OTA at levels of 2.0 and 5.0 ng/mL were 79% with RDS of 11% (n = 6). The limit of detection of the FP immunoassay was 0.7 ng/mL OTA, and the whole analysis was performed in less than 10 min. The assay was tested on 154 red wine samples (naturally contaminated or spiked at level ranging from 0.1 to 5.0 ng/mL) and compared with an high-performance liquid chromatography/immunoaffinity column clean-up method, showing a good correlation (r = 0.9222). Their compliance with the European regulation (2.0 ng/mL OTA maximum permitted level) was correctly assessed for 70% of the analyzed samples of red wine, whereas confirmatory analyses were required for the remaining ones with OTA levels close to the regulatory limit. No false-negative or positive results were observed using the FP immunoassay. The proposed FP assay is a useful screening method for OTA in red wines, when high throughput is required, that could also be used for white and rosé wines, which are known to contain less interfering compounds such as polyphenols.     

Prism‐Based Surface Plasmon Coupled Emission Imaging

A prism‐based surface plasmon coupled emission (SPCE) imaging apparatus with a reverse Kretschmann (RK) configuration was developed and applied to dye‐doped polymer films. Highly polarized, directional and enhanced fluorescence images were obtained. The angular distribution of the SPCE images was in accordance with the validated theoretical calculation performed using Fresnel equation. Prism‐based SPCE imaging combined with microarray technology appears to be a promising platform for rapid and high‐throughput analysis, especially for high‐density arrays. We believe that prism‐based SPCE imaging has potential applications in biochemical research.     

Simultaneous monitoring of the fluorescence and refractive index by surface plasmon coupled emission: A proof-of-concept study

Simultaneous acquisition of fluorescence property and refractive index using a single surface plasmon coupled emission (SPCE) measurement has been achieved, thus achieving synchronicity in real time. The SPCE sensor was employed for monitoring the adsorption of volatile organic compounds (VOCs) by dye-encapsulated metal-organic frameworks (Dye@MOFs). Refractive index can reveal surface molecular adsorption and the fluorescence with information on refractive index can provide a comprehensive analysis of the adsorption events of VOCs on the interface. Meantime, the signal intensity can be amplified by combining the responses caused by changes in refractive index and the fluorescence property in parallel. This all-in-one method opens up a route to monitoring multiple processes simultaneously occurring on the interface.     

A rapid fluorescence polarization immunoassay for the determination of T-2 and HT-2 toxins in wheat

A rapid fluorescence polarization (FP) immunoassay has been developed for the simultaneous determination of T-2 and HT-2 toxins in naturally contaminated wheat samples. Syntheses of four fluorescein-labelled T-2 or HT-2 toxin tracers were carried out and their binding response with seven monoclonal antibodies was evaluated. The most sensitive antibody-tracer combination was obtained by using an HT-2-specific antibody and a fluorescein-HT-2 tracer. The developed competitive FP immunoassay in solution showed high cross-reactivity for T-2 toxin (CR% = 100%) while a very low CR% for neosolaniol (0.12%) and no cross-reactivity with other mycotoxins frequently occurring in wheat. A rapid extraction procedure using 90% methanol was applied to wheat samples prior to FP immunoassay. The average recovery from spiked wheat samples (50 to 200 μg kg⁻¹) was 96% with relative standard deviation generally lower than 8%. A limit of detection of 8 μg kg⁻¹ for the combined toxins was determined. Comparative analyses of 45 naturally contaminated and spiked wheat samples by both the FP immunoassay and high-performance liquid chromatography/immunoaffinity clean-up showed a good correlation (r = 0.964). These results, combined with the rapidity (10 min) and simplicity of the assay, show that this method is suitable for high throughput screening as well as for quantitative determination of T-2 and HT-2 toxins in wheat.     

Intensified biochip system using chemiluminescence for the detection of Bacillus globigii spores

This paper reports the first intensified biochip system for chemiluminescence detection and the feasibility of using this system for the analysis of biological warfare agents is demonstrated. An enzyme-linked immunosorbent assay targeting Bacillus globigii spores, a surrogate species for Bacillus anthracis, using a chemiluminescent alkaline phosphatase substrate is combined with a compact intensified biochip detection system. The enzymatic amplification was found to be an attractive method for detection of low spore concentrations when combined with the intensified biochip device. This system was capable of detecting approximately 1 × 10⁵ Bacillus globigii spores. Moreover, the chemiluminescence method, combined with the self-contained biochip design, allows for a simple, compact system that does not require laser excitation and is readily adaptable to field use. Figure Schematic diagram of the miniature biochip detection system