Superhydrophobicity on two-tier rough surfaces fabricated by controlled growth of aligned carbon nanotube arrays coated with fluorocarbon

Considerable effort has been expended on theoretical studies of superhydrophobic surfaces with two-tier (micro and nano) roughness, but experimental studies are few due to the difficulties in fabricating such surfaces in a controllable way. The objective of this work is to experimentally study the wetting and hydrophobicity of water droplets on two-tier rough surfaces for comparison with theoretical analyses. To compare wetting on micropatterned silicon surfaces with wetting on nanoscale roughness surfaces, two model systems are fabricated: carbon nanotube arrays on silicon wafers and carbon nanotube arrays on carbon nanotube films. All surfaces are coated with 20 nm thick fluorocarbon films to obtain low surface energies. The results show that the microstructural characteristics must be optimized to achieve stable superhydrophobicity on microscale rough surfaces. However, the presence of nanoscale roughness allows a much broader range of surface design criteria, decreases the contact angle hysteresis to less than 1 degrees , and establishes stable and robust superhydrophobicity, although nanoscale roughness could not increase the apparent contact angle significantly if the microscale roughness dominates.     

可控阵列微纳结构超疏水铜表面冰霜传质特性

金属表面粗糙结构及其润湿性对其露、霜、冰的相变及传质现象有重要影响.通过电火花微加工和化学氧化法,本文首先实现了铜片表面微米、纳米阵列结构的可控制备.针对条纹,方柱和四棱锥三种典型微米结构特征,对比研究了单级粗糙结构和二级复合结构超疏水表面的润湿性、结露、结霜、结冰及其融化过程.微纳复合结构可有效增强超疏水性,减少霜晶形核和生长速度,同时还能大幅度延缓结冰的时间,多次冷热循环处理后,表面仍能保持较好的防霜抗冰性能.通过经典形核理论,Brown凝并,一维传热及传质理论,综合分析了冰霜在这种表面的传质特性.     

可控阵列微纳结构超疏水铜表面冰霜传质特性

金属表面粗糙结构及其润湿性对其露、霜、冰的相变及传质现象有重要影响. 通过电火花微加工和化学氧化法,本文首先实现了铜片表面微米、纳米阵列结构的可控制备. 针对条纹,方柱和四棱锥三种典型微米结构特征,对比研究了单级粗糙结构和二级复合结构超疏水表面的润湿性、结露、结霜、结冰及其融化过程. 微纳复合结构可有效增强超疏水性,减少霜晶形核和生长速度,同时还能大幅度延缓结冰的时间,多次冷热循环处理后,表面仍能保持较好的防霜抗冰性能. 通过经典形核理论,Brown 凝并,一维传热及传质理论,综合分析了冰霜在这种表面的传质特性.     

Dynamic (de)wetting properties of superhydrophobic plasma‐treated polyethylene surfaces

Superhydrophobic surfaces present properties of self‐cleaning and unwetting that could be applied in the optics field. The wetting and dewetting of these superhydrophobic surfaces are compared to that of only hydrophobic polyethylene. The contact angle of such a surface varies from 170° to 130–140°. The dewetting is studied using two techniques of dynamic dewetting measurements. The behaviors of surfaces, dried or prewetted with water vapor, are different. The dewetting of the dried surface previously prewetted is discontinuous, and slower than that of the dry one. This specific behavior is interpreted as a roughness effect on trapped water. However, its dewetting is still faster than a corresponding hydrophobic surface like polytetrafluoroethylene (PTFE). Copyright © 2006 John Wiley & Sons, Ltd.     

Extreme resistance of superhydrophobic surfaces to impalement: reversible electrowetting related to the impacting/bouncing drop test

The paper reports on the comparison of the wetting properties of superhydrophobic silicon nanowires (NWs), using drop impact impalement and electrowetting (EW) experiments. A correlation between the resistance to impalement on both EW and drop impact is shown. From the results, it is evident that when increasing the length and density of NWs (i) the thresholds for drop impact and EW irreversibility increase and (ii) the contact-angle hysteresis after impalement decreases. This suggests that the structure of the NW network could allow for partial impalement, hence preserving the reversibility, and that EW acts the same way as an external pressure. The most robust of our surfaces shows a threshold to impalement higher than 35 kPa, while most of the superhydrophobic surfaces tested so far have impalement thresholds smaller than 10 kPa.     

Mimicking natural superhydrophobic surfaces and grasping the wetting process: a review on recent progress in preparing superhydrophobic surfaces

A typical superhydrophobic (ultrahydrophobic) surface can repel water droplets from wetting itself, and the contact angle of a water droplet resting on a superhydrophobic surface is greater than 150°, which means extremely low wettability is achievable on superhydrophobic surfaces. Many superhydrophobic surfaces (both manmade and natural) normally exhibit micro- or nanosized roughness as well as hierarchical structure, which somehow can influence the surface's water repellence. As the research into superhydrophobic surfaces goes deeper and wider, it is becoming more important to both academic fields and industrial applications. In this work, the most recent progress in preparing manmade superhydrophobic surfaces through a variety of methodologies, particularly within the past several years, and the fundamental theories of wetting phenomena related to superhydrophobic surfaces are reviewed. We also discuss the perspective of natural superhydrophobic surfaces utilized as mimicking models. The discussion focuses on how the superhydrophobic property is promoted on solid surfaces and emphasizes the effect of surface roughness and structure in particular. This review aims to enable researchers to perceive the inner principles of wetting phenomena and employ suitable methods for creation and modification of superhydrophobic surfaces.     

Fabrication of superhydrophobic surfaces of n-hexatriacontane

Superhydrophobic surfaces of n-hexatriacontane were fabricated in a single-step process. The low surface energy of n-hexatriacontane together with the randomly distributed micro- and nanoscale roughness features guarantees very large contact angles and a small roll-off angle for water drops. The advantage of n-hexatriacontane superhydrophobic surfaces is their stability in the sense that they are impervious to chemical reactions and retain their wetting characteristics over a long period of time, as confirmed by XPS analysis and contact angle measurements.     

UVO-tunable superhydrophobic to superhydrophilic wetting transition on biomimetic nanostructured surfaces

A novel strategy for a tunable sigmoidal wetting transition from superhydrophobicity to superhydrophilicity on a continuous nanostructured hybrid film via gradient UV-ozone (UVO) exposure is presented. Along a single wetting gradient surface (40 mm), we could visualize the superhydrophobic (thetaH2O > 165 degrees and low contact angle hysteresis) transition (165 degrees > thetaH2O > 10 degrees ) and superhydrophilic (thetaH2O < 10 degrees within 1 s) regions simply through the optical images of water droplets on the surface. The film is prepared through layer-by-layer assembly of negatively charged silica nanoparticles (11 nm) and positively charged poly(allylamine hydrochloride) with an initial deposition in a fractal manner. The extraordinary wetting transition on chemically modified nanoparticle layered surfaces with submicrometer- to micrometer-scale pores represents a competition between the chemical wettability and hierarchical roughness of surfaces as often occurs in nature (e.g., lotus leaves, insect wings, etc).     

High- and low-adhesive superhydrophobicity on the liquid flame spray-coated board and paper: structural effects on surface wetting and transition between the low- and high-adhesive states

Surface wetting is an important and relevant phenomenon in several different fields. Scientists have introduced a large number of applications where special surface wetting could be exploited. Here, we study wetting phenomena on high- and low-adhesive superhydrophobic liquid flame spray (LFS)-generated TiO₂ coatings on paper and pigment-coated board substrates using water–ethanol solution as a probe liquid. Submicrometer-scale air gaps, which exist on superhydrophobic surfaces below the liquid droplets, were more stable with the ethanol increment than the larger-scale micrometric air gaps. With the droplet ethanol concentration of 15 wt%, static contact angle as high as 155?±?2° was measured on the LFS–TiO₂-coated board. Transition from the low-adhesive wetting state to the high-adhesive state was demonstrated on the LFS–TiO₂-coated paper. The LFS method enables efficient roll-to-roll production of surfaces with special wetting properties on economically viable board and paper substrate materials.     

Contact line and contact angle dynamics in superhydrophobic channels

The dynamics of the wetting and movement of a three-phase contact line confined between two superhydrophobic surfaces were studied using a mean-field free-energy lattice Boltzmann model. Principle features of superhydrophobic surfaces, such as trapped vapor/air between rough microstructures, high contact angles, reduced contact angle hysteresis, and low resistance to fluid flow, were all observed. Movement of the three-phase contact line over a well-patterned superhydrophobic surface displays a periodic stick-jump-slip behavior, while the dynamic contact angle changes accordingly from maximum to minimum. Two regimes were found for the flow velocity as a function of surface roughness and can be related directly to the balance between driving force and flow resistance. This work provides a better understanding of dynamic wetting and fluid flow behaviors over superhydrophobic surfaces and hence could be useful in related applications.     

Patterned nonadhesive surfaces: superhydrophobicity and wetting regime transitions

Nonadhesive and water-repellent surfaces are required for many tribological applications. We study mechanisms of wetting of patterned superhydrophobic Si surfaces, including the transition between various wetting regimes during microdroplet evaporation in environmental scanning electron microscopy (ESEM) and for contact angle and contact angle hysteresis measurements. Wetting involves interactions at different scale levels: macroscale (water droplet size), microscale (surface texture size), and nanoscale (molecular size). We propose a generalized formulation of the Wenzel and Cassie equations that is consistent with the broad range of experimental data. We show that the contact angle hysteresis involves two different mechanisms and how the transition from the metastable partially wetted (Cassie) state to the homogeneously wetted (Wenzel) state depends upon droplet size and surface pattern parameters.     

Condensation and wetting transitions on microstructured ultra-hydrophobic surfaces

On rough surfaces, two distinct wetting modes can appear. These two states are usually described by the theories of Cassie (drops suspended on top of roughness features) and Wenzel (drops impaled on roughness features). Whereas the wetting transition from the Cassie to the Wenzel state has been relatively well studied both experimentally and theoretically, the question of whether metastable Wenzel drops exist and how they transition to the Cassie state has remained open. In this work, we study the wetting behavior of microstructured post surfaces coated with a hydrophobic fluoropolymer. Through condensation, the formation of metastable Wenzel droplets is induced. We show that under certain conditions drops can transition from the Wenzel to the Cassie state.     

Laser-induced nanoscale superhydrophobic structures on metal surfaces

The combination of a dual-scale (nano and micro) roughness with an inherent low-surface energy coating material is an essential factor for the development of superhydrophobic surfaces. Ultrashort pulse laser (USPL) machining/structuring is a promising technique for obtaining the dual-scale roughness. Sheets of stainless steel (AISI 304 L SS) and Ti-6Al-4V alloys were laser-machined with ultraviolet laser pulses of 6.7 ps, with different numbers of pulses per irradiated area. The surface energy of the laser-machined samples was reduced via application of a layer of perfluorinated octyltrichlorosilane (FOTS). The influence of the number of pulses per irradiated area on the geometry of the nanostructure and the wetting properties of the laser-machined structures has been studied. The results show that with an increasing number of pulses per irradiated area, the nanoscale structures tend to become predominantly microscale. The top surface of the microscale structures is seen covered with nanoscale protrusions that are most pronounced in Ti-6Al-4V. The laser-machined Ti-6Al-4V surface attained superhydrophobicity, and the improvement in the contact angle was >27% when compared to that of a nontextured surface.     

Growth dynamics of water drops on a square-pattern rough hydrophobic surface

Condensation on rough or superhydrophobic substrates can induce wetting behavior that is quite different from that of deposited or impinging drops. We investigate the growth dynamics of water drops in a well-controlled condensation chamber on a model rough hydrophobic surface made of square pillars. After having followed growth laws similar to those observed on flat surfaces, a transition to an air-pocket-like state occurred because of the bridging of the drops between the pillars. Another transition to the more stable Wenzel state is later ensured by a noticeable pillar self-drying process. Condensation ends up in a few large drops in a mixed Wenzel penetration regime. The drops are fed by neighboring channels and the adjacent pillars stay almost dry, a remarkable and seemingly general property of rough hydrophobic substrates.     

Mimicking the lotus effect: influence of double roughness structures and slender pillars

Surface roughness is known to amplify hydrophobicity. The apparent contact angle of a drop on a rough surface is often modeled using either Wenzel's or Cassie's formulas. These formulas, along with an appropriate energy analysis, are critical in designing superhydrophobic substrates for applications in microscale devices. In this paper we propose that double (or multiple) roughness structures or slender pillars are appropriate surface geometries to develop "self-cleaning" surfaces. The key motivation behind the double structured roughness is to mimic the microstructure of superhydrophobic leaves (such as lotus). Theoretical analysis similar to that presented in the paper can be used to obtain optimal geometric parameters for the rough surface. The calculation procedure should result in surface geometries with excellent water repellent properties.     

Nanostructures increase water droplet adhesion on hierarchically rough superhydrophobic surfaces

Hierarchical roughness is known to effectively reduce the liquid-solid contact area and water droplet adhesion on superhydrophobic surfaces, which can be seen for example in the combination of submicrometer and micrometer scale structures on the lotus leaf. The submicrometer scale fine structures, which are often referred to as nanostructures in the literature, have an important role in the phenomenon of superhydrophobicity and low water droplet adhesion. Although the fine structures are generally termed as nanostructures, their actual dimensions are often at the submicrometer scale of hundreds of nanometers. Here we demonstrate that small nanometric structures can have very different effect on surface wetting compared to the large submicrometer scale structures. Hierarchically rough superhydrophobic TiO(2) nanoparticle surfaces generated by the liquid flame spray (LFS) on board and paper substrates revealed that the nanoscale surface structures have the opposite effect on the droplet adhesion compared to the larger submicrometer and micrometer scale structures. Variation in the hierarchical structure of the nanoparticle surfaces contributed to varying droplet adhesion between the high- and low-adhesive superhydrophobic states. Nanoscale structures did not contribute to superhydrophobicity, and there was no evidence of the formation of the liquid-solid-air composite interface around the nanostructures. Therefore, larger submicrometer and micrometer scale structures were needed to decrease the liquid-solid contact area and to cause the superhydrophobicity. Our study suggests that a drastic wetting transition occurs on superhydrophobic surfaces at the nanometre scale; i.e., the transition between the Cassie-Baxter and Wenzel wetting states will occur as the liquid-solid-air composite interface collapses around nanoscale structures. Consequently, water adheres tightly to the surface by penetrating into the nanostructure. The droplet adhesion mechanism presented in this paper gives valuable insight into a phenomenon of simultaneous superhydrophobicity and high water droplet adhesion and contributes to a more detailed comprehension of superhydrophobicity overall.     

Controlling the wettability of hierarchically structured thermoplastics

Surfaces play an important role in defining the properties of materials, controlling wetting, adsorption, or desorption of biomolecules, and sealing/bonding of different materials. We have combined microscale features with plasma-etched nanoscale roughness and chemical modification to tailor the wettability of the substrates. Cyclic olefin polymers and copolymers (COPs/COCs) were processed to make a range of surfaces with controlled superhydrophobic or -hydrophilic properties. The hydrophobic properties of the polymers were increased by the introduction of microstructures of varying geometry and spacing through hot embossing. The COC/COP substrates were functionalized by plasma activation in O(2), CF(4), and a mixture of both gases. The plasma etching introduces nanoscale roughness and also chemically modifies the surface, creating either highly hydrophilic or highly hydrophobic (contact angle >150°) surfaces depending on the gas mixture. The influence of geometry and chemistries was characterized by atomic force microscopy, contact angle measurements, and X-ray photoelectron spectroscopy. Measurements of the contact angle and contact angle hysteresis demonstrated long-term stability of the superhydrophobic/superhydrophilic characteristics (>6 months).     

Facile method to fabricate raspberry-like particulate films for superhydrophobic surfaces

A facile method using layer-by-layer assembly of silica particles is proposed to prepare raspberry-like particulate films for the fabrication of superhydrophobic surfaces. Silica particles 0.5 microm in diameter were used to prepare a surface with a microscale roughness. Nanosized silica particles were then assembled on the particulate film to construct a finer structure on top of the coarse one. After surface modification with dodecyltrichlorosilane, the advancing and receding contact angles of water on the dual-sized structured surface were 169 and 165 degrees , respectively. The scale ratio of the micro/nano surface structure and the regularity of the particulate films on the superhydrophobic surface performance are discussed.     

From rolling ball to complete wetting: the dynamic tuning of liquids on nanostructured surfaces

In this work, for the first time, a dynamic electrical control of the wetting behavior of liquids on nanostructured surfaces, which spans the entire possible range from the superhydrophobic behavior to nearly complete wetting, has been demonstrated. Moreover, this kind of dynamic control was obtained at voltages as low as 22 V. We have demonstrated that the liquid droplet on a nanostructured surface exhibits sharp transitions between three possible wetting states as a function of applied voltage and liquid surface tension. We have examined experimentally and theoretically the nature of these transitions. The reported results provide novel methods of manipulating liquids at the microscale.