A CRL–IRMM joint proficiency test for trace elements in fish tissue

The Community Reference Laboratory (CRL) for residues and contaminants in food of animal origin at the Istituto Superiore di Sanità (ISS) plans and undertakes on a regular basis Proficiency Tests Schemes (PTSs) focused on the residues under its responsibility, as prescribed by the Council Directive 96/23/EC of April 29, 1996. In consideration of the benefits ensuing from a constant monitoring of the daily activities of the National Reference Laboratories (NRLs) for residues in the Member States, the ISS–CRL frequently prepares test materials to promote comparability of data and support harmonisation of routine analytical procedures. When target values for the analytes are set, the PTSs also provide objective assessment and improvement of the analytical trueness in the daily work.In this context, an interlaboratory comparison for trace elements in tuna fish matrix was organised in cooperation with the Institute for Reference Materials and Measurements (IRMM), Joint Research Centre, European Commission. Freeze-dried tuna fish samples were sent out to the NRLs for chemical elements in the Member States. Participants were requested to carry out at least three independent measurements of the elements As, Cd, Cr, Cu, Fe, Hg, Pb and Zn. The assessment of the proficiency was based on the z-score approach and a relative bias better than or equal to 10% of the target value was deemed to be an acceptable performance for this kind of measurements. On this basis, more than 50% of the laboratories returned accurate results for As, Cu, Fe, Hg and Zn, whereas the analysis of Cd, Cr and Pb appeared to be more problematic.     

Recent developments in assessment of bio-accessible trace metal fractions in airborne particulate matter: A review

In the last years a great deal of research has been focused on the determination of harmful trace metals such as Cd, Co, Cr, Cu, Ni or Pb in airborne particulate matter (APM). However, the commonly applied determination of total element concentrations in APM provides only an upper-end estimate of potential metal toxicity. For improved risk assessment it is important to determine bio-accessible concentrations instead of total metal contents. The present review gives an overview of analytical procedures reported for measurement of bio-accessible trace metal fractions in APM. The different approaches developed for extraction of soluble trace metals in APM are summarized. Furthermore the analytical techniques applied for accurate determination of dissolved trace metals in the presence of complex sample matrix are presented. Finally a compilation of published results for bio-accessible trace metals in APM is included.     

Determination of heavy metals by inductively coupled plasma-optical emission spectrometry in fish from the Piracicaba River in Southern Brazil

A total of 202 fish, representing 16 species, were collected during 2008 (March–October) in the Tanquan region of the Piracicaba River using nets. Flesh samples were collected and analyzed, using inductively coupled plasma-optical emission spectroscopy for Al, As, Cd, Co Cr, Cu, Mn, Mo, Ni, Pb, Se, Sn, Sr, and Zn. The results showed that the flesh of these fish all contained extremely high levels of Al and Sr, and moderately high levels of Cr, As, Zn, Ni, Mn and Pb. The metals were higher in these fish during rainy season, with fish collected during the months of March and October being the highest. In addition, the accumulation of metals was species-dependent. Cascudos (Hypostomus punctatus) and piranhas (Serrasalmus spilopleura) exhibited high levels of almost all of the metals, while curimbata (Prochilodus lineatus) had moderate levels. A few species, including pacu (Piaractus mesopotamicus) and dourado (Salminus maxillosus), had very low levels of most metals. The results show that the Piracicaba River Basin is widely contaminated with high levels of many toxic heavy metals, and that human consumption of some fish species is a human health concern.     

Evaluation of 10-years French NRL proficiency tests for lead, cadmium and mercury analysis in foodstuff of animal origin

The French National Reference Laboratory (NRL) for heavy metals in foodstuffs of animal origin at the French Food Safety Agency (AFSSA) regularly organises proficiency tests schemes (PTS) focused on the quantification of the three elements lead (Pb), cadmium (Cd) and mercury (Hg), for the 23 departmental laboratories of the network of laboratories, under its responsibility. The NRL prepares test materials to promote comparability of data and support harmonisation of official analytical procedures in the case of routine analysis. When target values for the analytes are set, the PTS also provide an objective assessment and improvement of the analytical trueness in the daily work of the laboratories.The long-term performance of the network was examined using results of 10 years of PTS in various matrices from different foodstuffs of animal origin (fish, meat and milk products), with 3 different official methods, using Flame- and Electro-Thermal-AAS techniques. In all cases, participants were requested to carry out 3 independent measurements of Pb, Cd and Hg. Moreover, the assessment of the PTS was based on the Z-score approach. From 1998 to 2008, this evaluation applied to 690 results obtained in 41 PTS indicated a frequency distribution of the Z-score value for the three elements Pb, Cd and Hg of 89.2%, 94.5% and 97.7% of acceptable results, respectively. The results of this balance sheet indicated the homogeneity and ability of the laboratories network to provide comparable results of similar quality. Comparison with results obtained by a primary method were presented as complementary information to determine the interest to organize, in the future, PTS based on a certified value.     

Neutron activation analysis of some of the biologically active trace elements in fish

Highly specific neutron activation analysis procedures involving post irradiation chemical separations were developed for the determination of Cu, Hg, Zn, Cd, As, Se and Cr in fish tissues. The procedures developed were used to determine the levels of these biologically active elements in some of the commercially important fish species of Lake Erie. The nuclear analytical procedures developed generally involved the irradiation of fish tissues followed by wet-ashing in the presence of nonradioactive carriers From the homogeneous solution of the tissue digest, the elements of interest were chemically isolated and the radio-activities were measured by scintillation gamma ray spectrometry. The results reported include both the determination of the precision and accuracies of each of these elemental analyses and a survey of these seven elements in nine major fish species of Lake Erie.     

Method validation for determination of arsenic, cadmium, chromium and lead in milk by means of dynamic reaction cell inductively coupled plasma mass spectrometry

With Regulation No. 1881/2006 the European Union fixed a maximum level for lead in milk. Consequently, there is the need to determine very low concentration of elements that may be present in milk in trace and ultratrace levels.Quadrupole inductively coupled plasma mass spectrometry (Q-ICP-MS) combined with dynamic reaction cell (DRC) has been widely employed in order to reach very low concentration, requested for this product. Furthermore, the DRC technology can help in removing polyatomic and argon-based interferences.In the present study, a method for the determination of arsenic, cadmium, chromium and lead in bovine milk was validated according to the EU common standards by means of DRC-ICP-MS. The main parameters evaluated in the validation were: recovery, repeatability and within-laboratory reproducibility, detection and quantification limits, linearity range and measurement uncertainty. Additionally, stability studies of the analyte in solution and ruggedness studies were carried out.The results obtained for limit of detection (LoD) and limit of quantification (LoQ) in μg kg⁻¹ were respectively: As, 3.1 and 9.5; Cd, 0.08 and 0.24; Cr, 0.229 and 0.693; Pb, 0.5 and 1.5. While for the recovery: As, 91%; Cd 96%; Cr 99%; Pb, 95%. As for the repeatability: As, 7%; Cd, 3%; Cr, 6%; Pb, 4%.     

An international interlaboratory study for the production of a sewage sludge certified reference material for routine use in inorganic quality control

Two existing interlaboratory schemes are used to certify a sewage sludge reference material. Data from the analysis (As, Cd, Cr, Cu, Pb, Hg, Ni and Zn) of the material using routine procedures, US EPA and Netherlands NEN, plus INAA and IDMS and an interlaboratory comparison in Eastern Europe have been examined. The Dutch results show significantly lower analytical results for As for the graphite furnace technique compared to HG-AAS, probably due to matrix-effects. The differences between the Dutch and USA results for Cr and Ni suggest that the USEPA 3050A digestion method for dissolution of the metals is less aggressive for this material compared to aqua regia destruction. For international comparability of analytical data it is essential to harmonize method dependent dissolution/extraction techniques. The preparation of reference materials which mimic real samples and certification by ILS result in useful materials for quality control.     

Evaluation of serum metal profile in relation to biri smoking using ICP-MS

The metals intake through tobacco smoking is associated with adverse effects for human health. The present study was aimed to understand the effects of biri smoking on smoker’s serum metal profile. Seven metals, cadmium (Cd), nickel (Ni), lead (Pb), chromium (Cr), copper (Cu), iron (Fe) and zinc (Zn), were analysed in serum samples of 20 biri smokers and 20 non-smokers from North India. The Cd, Ni, Pb, Cr and Cu concentrations were higher while Fe and Zn concentrations were lower in smokers compared to non-smokers. The Fe concentrations, the highest among all metals, seemed to be unassociated with the smoking activity. This study indicated that biri smoking is a contributor to the body burden of Cd, Ni, Cu and Cr in the smoker’s body. The Cd, Ni, Cu and Fe concentrations are non-significantly associated with the age of smokers at p < 0.01 significance level, whereas Pb and Cr concentrations increase and Zn concentrations decrease with the increase in the age of smokers. Serum metal concentrations in the smoker subjects of North India are higher compared to the results of other similar studies. This could be linked to the poor quality of tobacco used in biri. We recommend conducting more detailed and controlled studies in this regard as a smoker is also subjected to other sources of exposure to metals.     

Metals in water and surface sediments from Henan reaches of the Yellow River, China

The concentrations of Cd, Cr, Cu, Ni, Pb and Zn were determined in the water and surface sediments from the Henan reaches of the Yellow River. Twenty-three sampling sites along the Yellow River and its tributaries were selected. Generally, metal concentrations were found to decrease in sequences of Zn > Cu > Pb > Cr > Ni > Cd in water and Zn > Cr > Pb > Ni > Cu > Cd in sediments. High levels of metal concentration were determined at a few stations of the river and its tributaries, such as Yiluo River, Si River and Qin River. The pollution of the Yellow River by Cd, Cr, Cu, Ni, Pb and Zn can be regarded as much higher compared to the background values, US EPA criteria (1999) and China water quality criteria (2002). For sediments, metal levels except Pb did not significantly exceed the average shale levels and backgrounds in several countries including China. Data analysis manifests that positive correlations were found between Cu, Ni and Zn in water, and Pb, Ni, Zn and Cr in sediments. The Pearson correlation coefficient analysis and Cluster analysis were provided to assess the possible contamination sources. The results indicate a general appearance of serious pollution along the banks of the Yellow River. The wastewaters discharged by the mine plants, smelter plants, power plants, battery plants, tannery plants, etc., and sewage inputs from the cities along the river banks may be the sources of metals.     

INAA and PIXE for the determination of the contents of extractable sediment

The three-stage BCR sequential step reference extraction procedure was applied to the reference material BCR CRM 601, especially developed for fractionation studies. Extracted fractions were analyzed for Cr, Ni, Zn, Cd, and Pb, by k ₀-standardized instrumental neutron activation (k ₀ INAA) and proton induced X-ray emission (PIXE), and flame atomic absorption spectrometry (FAAS). Sample preparation procedures were developed for both k ₀ INAA and PIXE techniques, related to the evaporation of the solutions in order to get solid samples for neutron and proton irradiation. Quality control was assessed by intercomparison of the analytical results obtained by the applied techniques, which included results for a few certified reference materials. In the extracted fractions, chromium concentration was not determined accurately by both nuclear techniques. Concerning Cd, Ni, Pb, and Zn, the results were in general in good agreement with the certified values and FAAS. Some incomplete separation of the residue might have occurred.     

Trace element analysis in CRM of plant origin by inductively coupled plasma mass spectrometry

Three CRMs of plant origin (SRM 1515 Apple Leaves, SRM 1570a Trace Elements in Spinach Leaves, and SRM 1575 Pine Needles) were used for analytical quality assurance of Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Mo, Cd, and Pb determination by ICP-MS. The samples were decomposed using microwave assisted pressurized digestion by HNO₃ and HNO₃ + H₂O₂ mixture and temperature programmed dry ashing. Concentrations of elements in samples were evaluated by external calibration. All samples, blanks, and standards were spiked to 100 μg/L concentration of In and Bi as internal standards. During the measurement, signals of ⁵²Cr, ⁵³Cr, ⁵⁴Fe, ⁵⁵Mn, ⁵⁹Co, ⁶⁰Ni, ⁶²Ni, ⁶³Cu, ⁶⁵Cu, ⁶⁶Zn, ⁹⁵Mo, ¹¹¹Cd, ¹¹²Cd, ¹¹⁵In, ²⁰⁶Pb, ²⁰⁷Pb, ²⁰⁸Pb and ²⁰⁹Bi were monitored. Results of Pb, Cd, Cu, Zn, Mo and Co determination were in good agreement with certified values. In order to obtain accurate results for As at low levels, it was necessary to mathematically correct the analytical signal. This correction effectively eliminates the influence of interfering ArCl⁺ ions. For Cr analysis it is advisable to use as powerful oxidizing conditions during sample decomposition as possible.     

Lichen based biomonitoring of air quality in Havana City west side

Summary An epiphytic lichen (Physcia alba sp.) grown over Roystonea regia tree was used as biomonitor of air quality in the Havana City west side. During the survey, 81 sampling sites were selected according to traffic and industry conditions. The concentration for 14 elements (Mg, Al, Ca, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Sr, Cd and Pb) was determined by flame atomic absorption spectrometry (FAAS) and anodic stripping voltammetry (ASV). Contents of Cu, Zn, Cd and Pb obtained by both techniques were compared. Several biological reference materials (RM's) were analyzed in order to assure the quality of analytical results. Some pollution sources were identified using principal component analysis. A total of 5 factors were achieved, of which 4 could be interpreted in terms of anthropogenic pollution sources. However, the expected correlation between traffic influence and lead concentration in lichen could not be demonstrated. The factor values patterns are presented.     

Quality assurance program for the chemical characterization of soils

A quality assurance program has been developed both to assess and to demonstrate the quality of the results produced by an analytical diagram applied to the chemical characterization of soils. The composition of several soils was determined following procedures based on the methods that are applied to silicate materials. A combination of acid decomposition followed by fusion allows the determination of SiO₂, Al, Fe, Ca, Mg, Ti, P, Mn, Cd, Co, Cr, Cu, Ni, Pb and Zn; a specific acid attack was used for Hg analysis and an acid mixture decomposition to analyse Na, K, Li and Sr. Several quality control parameters, namely calibration function characteristics, limits of detection, limits of quantification, quality control standards, duplicate analysis, spike recoveries and certified reference materials analysis, are introduced, evaluated and discussed. The results obtained for the certified reference materials show that the analytical diagram gave acceptable accurate values for the elements applying the quality assurance program proposed.     

Effects of processing on five selected metals in the durum wheat food chain

The concentration levels of five metals, namely Cd, Cr, Fe, Ni and Pb, were investigated along the durum wheat processing chain, from grain to the final product. Cadmium and Pb are well-known toxic elements and their levels in wheat grain are regulated by the European legislation. Chromium, Fe and Ni were included in the study as markers of metal release from equipment during processing. Durum wheat grain, semolina and pasta were sampled at an industrial plant for milling and pasta making. Samples were taken at different stages along processing in order to elucidate the influence of each stage on the element content. Samples of the water used for grain tempering and dough preparation were also collected. The whole analytical procedure, from sampling to final analytical determinations, was carried out according to a pre-established quality assurance protocol. Analyses were performed by inductively coupled plasma mass spectrometry (ICP-MS) and inductively coupled plasma atomic emission spectrometry (ICP-AES).Milling was the key process influencing the concentrations of the studied elements and reduced the metal levels according to a definite element-specific pattern. Purity of the water used as ingredient, element deposition from plant air and metal release from equipment were identified as critical issues in contamination control during processing. In the conditions of this study, it was found that a simple relationship can be established between the original concentrations in durum wheat grain and those in pasta for Cd and Fe, while for Pb, Cr and Ni, a greater uncertainty in the estimation of the levels in the final product is expected.     

Planning and certification of new multielemental reference materials for research in antarctica

The adoption of the principles of Good Laboratory Practice (GLP) and the implementation of the ensuing procedures for quality assurance (QA) and quality control (QC) of analytical determinations are nowadays deemed essential to the achievement of sound, credible and comparable experimental information. This is certainly also applicable to research projects currently being carried out in the antarctic continent, in particular as regards investigations on global change phenomena. Worldwide investments made so far in this field do require in fact that reliability of data be optimized so as to allow for a harmonized assessment of ongoing trends. In this context the Italian National Programme for Research in Antarctica has recently launched a project for the preparation of new multielemental certified reference materials (CRMs) to be used for QC of analyses performed on environmentally significant materials. The suitability of CRMs to verify the accuracy of experimental measurements acknowledgedly depends, among others, on the degree of similarity of their matrix composition and analyte levels to those expected for real samples. From this standpoint three CRMs are planned, namely: i) marine sediment certified for Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn and Zn; ii) ocean water certified for Cd, Cr, Cu, Fe, Hg, Mn, Ni and Pb; iii) krill certified for As, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn and Zn. Regarding the first two matrices, amounts of ca. 100 kg and ca. 1001, respectively, have been collected during the IX (1993–1994) antarctic expedition, while krill was taken in the course of the X (1994–1995) campaign. The pretreatment of sediment has been accomplished in terms of homogenization, stabilization and characterization of the preliminary ground mass. Approximately 500 bottles, each containing 75 g of material are now ready for distribution to interested laboratories involved in chemical measurements of antarctic matrices, whereas ocean water and krill will follow at a later stage. Finally, depending on circumstances, also the certification of organochlorine compounds in the same materials will be attempted.     

Elemental Analysis of Edible Mountain Nettle (Obetia tenax) and the Influence of Soil on Its Chemical Composition

In developing countries, the dietary intake of essential elements is largely dependent on the consumption of edible fruits and leafy vegetables. The distribution of elements in the indigenous edible plant, Obetia tenax (mountain nettle), was investigated as a function of soil quality from eight sites in KwaZulu-Natal, South Africa. The results show concentrations of elements in the leaves to be in decreasing order of Ca?>?Mg?>?Fe?>?Mn?>?Zn?>?Cr?>?Cu?>?Ni?>?Pb?>?Co?>?As?>?Cd?>?Se, and in the stems and roots to be in decreasing order of Ca?>?Mg?>?Fe?>?Mn?>?Zn?>?Cu?>?Ni?>?As?>?Pb?>?Co?>?Cd?>?Cr?>?Se. The quality and pollution status of soil was evaluated by geoaccumulation indices and enrichment factors, which indicated moderate cadmium contamination at the Msinga location that was confirmed by the pollution index and ecological risk levels of single-factor pollution. An assessment of overall contamination of soil using Nemerow pollution index showed moderate pollution by cadmium, while the potential toxicity index indicated low-grade risk for all elements at all sites. Principal component and cluster analysis revealed two groups of elements with similarities, As, Cd, Co, Cr, Cu, Mn, Ni, and Fe, suggesting a lithogenic source and an anthropogenic source for Pb and Zn. Correlation analysis showed significantly positive correlations between As, Co, Cr, Cu, Fe, and Ni/Cd in the soil, confirming the elements’ common origin.     

A review of heavy metal contaminations in urban soils, urban road dusts and agricultural soils from China

This paper reviews quite a few heavy metal contamination related studies in several cities from China over the past 10 years. The concentrations, sources, contamination levels, sample collection and analytical tools of heavy metals in urban soils, urban road dusts and agricultural soils were widely compared and discussed in this study. The results indicate that nearly all the concentrations of Cr, Ni, Cu, Pb, Zn, As, Hg and Cd are higher than their background values of soil in China. Among the cities, the contamination levels of the heavy metals vary in a large range. The geoaccumulation index shows that the contamination of Cr, Ni, Cu, Pb, Zn and Cd is widespread in urban soils and urban road dusts of the cities. Generally, the contamination levels of Cu, Pb, Zn and Cd are higher than that of Ni and Cr. Agricultural soils are also significantly influenced by Cd, Hg and Pb derived from anthropogenic activities. The integrated pollution index (IPI) indicates that the urban soils and urban road dusts of the developed cities and the industrial cities have higher contamination levels of the heavy metals. The comparison of the IPIs of heavy metals in urban soils and urban road dusts of Shanghai, Hangzhou, Guangzhou and Hongkong reveals that the contamination levels of the metals in urban road dusts are higher than that in urban soils in the cities. Moreover, the main sources of the metals in urban soils, urban road dusts and agricultural soils are also different.     

Evaluation of the bioaccumulation of trace elements in tuna species by correlation analysis between their concentrations in muscle and first dorsal spine using microwave-assisted digestion and ICP-MS

Environmental pollution by metals is a recognized problem worldwide. As a result of the exposure to this pollution, marine species may bioaccumulate metals in both muscle and fishbone, as has been demonstrated in some species of tuna. The objective of this study has been the development and optimization of an inductively coupled plasma-mass spectrometry (ICP-MS) based method, which allows the quantification of 21 elements including priority pollutants and biologically essential elements (B, Mg, Al, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Pd, Cd, Ba, La, Hg and Pb) in muscle and in the first spine of the first dorsal fin of albacore (Thunnus alalunga) and bluefin tuna (Thunnus thynnus). A microwave-assisted digestion has been developed for sample treatment, which has been evaluated using isotope dilution analysis (IDA) of Cr, Se, Cd, Ba and Pb. Evaluation of the analytical method in terms of sensitivity (LOQ between 0.002 and 1?mg?kg^?1), accuracy and precision within and between days (CV?<?11.3%) has also been conducted. The developed method has allowed information to be obtained on levels of these metals in both matrices. The correlation analyses performed for each of the metals in both matrices shows a positive linear relationship between the concentrations in muscle and fishbone for Zn, Se, Rb, Cd, As and Hg, which could be due to a higher bioaccumulation of these elements in muscle as it is concluded from the low spine/muscle ratios observed for these elements. The 34 specimens of tuna analyzed show that while the levels of Pb, Cd, Ni, Zn, Cu and Cr in muscle are below the limits set by the WHO/FAO, EC and the US-EPA, Hg shows higher concentration than the limits set by the EC in four samples, indicating a potential risk to human health.     

Comparative study of heavy metal and trace element accumulation in edible tissues of farmed and wild rainbow trout (Oncorhynchus mykiss) using ICP-OES technique

The objective of this research was to determine the differences between farmed and wild rainbow trout in terms of heavy metal and trace element accumulation in edible tissues. The samples were analyzed for As, Ba, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Se, Sr and Zn by inductively coupled plasma-optical emission spectrometry (ICP-OES); and for Hg by cold vapor atomic absorption spectrometry (CVAAS). The results were expressed as μg/g of dry weight. With the exception of Ba and Sr, liver had significantly higher heavy metal and trace element concentrations compared to the muscle in farmed or wild fish. Higher levels of Ba, Cr, Fe, Mn and Zn, as well as lower levels of Cu and Sr were found in tissues of wild rainbow trout compared to its farmed relative. Levels of Cd in 41.6% of farmed fish samples and 45.8% of wild fish samples exceeded the European Commission regulation. Regarding the Pb, concentrations in 50% of farmed fish samples and 62.5% of wild ones were above the European Commission limit. However, levels of Hg and As in all of the examined samples were lower than the legislated limits. The differences in heavy metal and trace element accumulation observed between farmed and wild fish were probably related to the differences in their environmental conditions and dietary element concentrations.     

Producing SI-traceable reference values for Cd, Cr and Pb amount contents in polyethylene samples from the Polymer Elemental Reference Material (PERM) project using isotope dilution mass spectrometry

 The present paper describes the certification of the amount content of Cd, Cr and Pb in two different polyethylene materials within the third phase of the Polyethylene Elemental Reference Material (PERM) project. The analytical procedure to establish the reference values for Cd, Cr and Pb amount contents in these materials is based on isotope dilution mass spectrometry used as a primary method of measurement. Cd and Pb were measured with inductively coupled plasma-mass spectrometry and Cr with positive thermal ionization-mass spectrometry. The decomposition of the polymer matrix was carried out using a high pressure asher. Reference values for amount content, traceable to the SI-system, have been obtained for these three elements in both of the polyethylene samples of PERM. For each of the certified amount content values an uncertainty budget was calculated using the method of propagation of uncertainties according to ISO and EURACHEM guidelines. The measurement procedures, as well as the uncertainty calculations, are described for all three elements. In order to keep the whole certification process as transparent as possible, the preparations of various reagents and materials as well as the sample treatment and blending are described in detail. The mass spectrometry measurements and the data treatment are also explained carefully. The various sources of uncertainty present in the procedure are displayed in the uncertainty budgets. The obtained combined uncertainties for the amount content values were less than 2% relative (k=1) for all investigated elements. The amount contents were in the μmol/kg range, corresponding to mg/kg levels. Received: 21 October 1999 / Accepted: 29 January 2000