铜镍合金丝电爆炸放电特性与时空演化行为

脉冲电流驱动金属丝电爆炸可产生具有较高能量密度的等离子体,并伴随脉冲电磁辐射、强冲击波等效应,广泛应用于Z箍缩、电热化学武器、油气助采等领域;与纯金属相比,合金具备电阻率高、成分可调、相变复杂等特点,在电爆炸效应参数的调控方面具有很大潜力。开展了大气空气介质中铜、镍、铜镍（康铜）丝在微秒时间尺度电脉冲作用下电爆炸实验研究,通过放电参数与自辐射图像诊断,获取电爆炸过程放电参数与时空演变的特性规律,得到脉冲电流作用下合金电爆炸在相变与等离子体方面的特征。实验发现,在电爆炸早期,铜镍合金的高电阻率能够提高能量沉积效率:铜52%、镍74%、铜镍合金78%;而相爆开始后,合金丝负载则更接近纯镍丝负载性能。等离子体通道早期膨胀速率在5 mm/μs量级,随后迅速衰减;合金丝等离子体膨胀时间更久,击穿后平均电阻率上升缓慢,且等离子体辐射与金属爆炸产物在空间尺度上存在关联性。特别地,铜镍合金气溶胶分层同时具有横向和纵向特征（特征尺度10?1 mm）,但整体较铜气溶胶更为均匀。     

Characterization of brush type discharge electrodes and impact of enhanced corona discharge on operation of electrostatic precipitators

This project presents the results of investigation of current/voltage characteristics of brush type discharge electrodes (BTDE) in tube type electrostatic precipitators and the effect on operation. Experimental investigations were conducted with discharge electrodes of different wire diameter and different brush diameter. The effect of electrode geometry on current/voltage behavior was recorded. Corona current with brush type discharge electrodes was modeled and compared with experimental data. Brush type discharge electrodes produce an enhanced corona current compared with wire type discharge electrodes. Limited enhanced corona has improving effect on collection efficiency. An adjusted correlation was therefore deduced from experimentally obtained current/voltage data with BTDE.     

Prolonged microbial resistance of water treated by a pulsed electrical discharge

The main characteristics of pulsed discharges in water are studied, such as the discharge current, voltage drop across the discharge gap, temperature of the discharge column, and plasma conductivity, as well as compression waves and ultraviolet radiation, which are induced by the discharge. The physicochemical properties of water treated by pulsed discharges are considered in the context of the effect produced on microorganisms. The mechanism underlying the prolonged microbial resistance of water—its capability of retaining a high activity against virtually all known pathogenic microorganisms and human-opportunistic fungi for many months after the discharge treatment—is explained.     

丝电爆过程的电流导入机理

丝电爆制备纳米粉时, 电流从电极导入金属丝的过程直接影响电极烧损和粉末中微米级大颗粒产生. 分别通过接触和气体放电两种方式导入电流进行电爆试验. 结果表明, 光测量装置检测到的丝端部光电流几乎与回路放电电流同时产生, 而中间位置的光电流则要滞后一段时间; 由探针收集的产物确定, 金属丝端部主要形成熔融粒子, 中间部分主要形成气相粒子. 分析可知, 接触方式导入电流时, 丝端部也存在气体放电现象, 大电流主要通过气体放电形成的等离子体导入. 等离子体对电流的旁路作用会阻碍能量向金属丝沉积, 这是产生微米级大颗粒和"积瘤"主要原因. 通过气体放电方式导入电流时, 电极烧损明显减轻, 并可以避免"积瘤"产生.     

Charging effects in biased molecular devices

The influence of charging effects on the transport characteristics of a molecular wire bridging two metallic electrodes in the limit of weak contacts is studied by the generalized Breit–Wigner formula. Molecule is modeled as a quantum dot with discrete energy levels, while the coupling to the electrodes is treated within a broad-band theory. Owing to this model we find self-consistent occupation of particular energy levels and orbital energies of the wire in the presence of transport. The nonlinear conductance and current–voltage characteristics are investigated as a function of bias voltage in the case of symmetric and asymmetric coupling to the electrodes. It is shown that the shape of those curves are determined by the combined effect of the electronic structure of the molecule and by electron–electron repulsion.     

双路大电流源模块水中放电实验研究

高压电脉冲压裂技术是基于液电效应,通过水中脉冲放电产生强大的冲击波使岩石产生裂缝,近年来成为了岩石压裂领域的热点研究对象。搭建了两路电流源模块应用于水中放电,采用铜材料的针针电极,电极间距1 mm;研究了在不同放电电压下,单路和两路电流源模块电极间的电压、电流波形。实验结果表明,空载时在同一放电电压下,双路模块产生更大的放电电流,从而在放电时获得更高的瞬时功率;而在水中针针放电时,单路和双路模块水间隙的预击穿时间与放电电压之间具有很大的随机性。单路模块预击穿时间的标准差最小为0.285 ms,最大为1.481 ms;而双路模块最小为0.369 ms,最大为0.703 ms。并且随着放电电压的增加,预击穿时间减小,双路模块的预击穿平均时间从放电电压为1300 V时的2.686 ms降到1800 V时的1.036 ms。     

Analysis of Plasmadynamic Nanosecond-Range Processes in the Formation of Shock Waves from Pulsed Discharges

We have studied the dynamics of the plasma glow of pulsed discharges (sliding surface discharge and combined volume discharge with plasma electrodes) in the nanosecond range (100–12 000 ns) in stationary air and in the flow behind the front of a plane shock wave with Mach numbers 1.7–5.0 in the shock tube channel. The temporal characteristics of the flow, the radiation spectra, and the discharge currents in air are compared in the pressure range 5–150 Torr, a pulsed voltage of 20–30 kV, and a current of about 1 kA. It is shown that the time of current under various conditions does not exceed 400 ns, and the duration of the glow can reach a few microseconds. It is shown that as a result of energy supply near the planar shock wave front, the decay of discontinuities occurs with the formation of shock waves and contact surfaces. The positions of the plasma glow regions are compared with the positions of discontinuity surfaces of numerically calculated gasdynamic parameters in the flow.     

Study on both discharge and charging of the earthed atomizing corona discharge and the influence of magnetic fields on them

In the paper, the influences of water flux on both discharge current and onset voltage were studied. Both charging and capturing particles of atomizing corona discharges were investigated when the magnetic field was used or not. The charge number of droplets and their sizes were calculated after some parameters were measured by Millikan oil drop instrument. In addition, the capturing ability of atomizing corona discharge pre-charger with magnetic field was compared with the traditional pre-charger. Eventually, the charging mechanism of atomizing corona discharge with magnetic field was analyzed through the above-mentioned experimentation and comparison. The result shows that the smallest onset voltage will appear with water flow increase in the atomizing corona discharge, and that the ion concentration between electrodes is the highest in the atomizing corona discharge charger with magnetic field than any other pre-charger, which is conducive for charging dust particles. Hence the new pre-charging technique is promising for capturing fine aerosol particles in electrostatic precipitators.     

Modeling of pulsed spark discharge in water and its application to well cleaning

This paper presents a simulation model for the generation of strong pressure wave by means of pulsed spark discharge in water and its application to well cleaning. In the simulation model, one-dimensional time-dependent magnetohydrodynamic equations are coupled to a capacitive discharge circuit equation. A cylindrical conducting spark channel formed by electrical breakdown of water gap between a pair of electrodes is treated as a load of which resistance and inductance are allowed to change with time. For describing the spark channel properties accurately, precise calculations on thermodynamic properties and electrical conductivity are included in the simulation model. The simulation results show an excellent agreement with the experimentally measured shock pressure as well as the current and voltage waveforms. The simulation reveals that Joule heating of the spark channel during the very early phase of electrical discharge plays a key role in the formation of shock wave in water. The voltage on a capacitor at breakdown, the circuit inductance, and the resistance of the spark channel are found to be the most important parameters for the shock wave formation. With this technique, a pilot test for the cleaning of a clogged well has been performed in a water well which was constructed as a test-bed for riverbank filtration near the Anseong-cheon (river) in Korea. Well treatments have been carried out with an electrical energy of 510 J stored on a pulsed power system, at which the maximum shock pressure is measured to be around 7 MPa at the position of the well screen, i.e. 0.1 m away from the spark gap. A slug test shows 2.9 times improvement in the hydraulic conductivity of the well, which, combined with a visual inspection inside the well using an underwater camera, clearly demonstrates that the strong pressure wave generated by underwater spark discharge can effectively remove almost all incrustations formed in the well screen and thus improve well performance. Operating parameters for controlling the strength of shock pressure are discussed using the simulation model for extensive applications of the present technique to various types of water wells.     

铝单丝Z箍缩形成无核冕结构的物理分析

针对铝单丝Z箍缩负载,计算其可形成金属蒸气而不形成核冕等离子体的电路和负载参数范围。提出了铝丝电爆炸形成金属蒸气的能量沉积判据和击穿电压判据;建立了热动力学模型,选取电路参数使得金属丝气化时放电回路电流恰好迅速下降,从而避免发生电压击穿。计算了典型电路下的负载电流、电压、电阻及沉积能量的变化曲线,并分析了回路总电感、充电电压以及负载丝长度、直径对其的影响规律。计算结果表明:当储能电容为150pF、充电电压为65kV、回路电感为300nH时,可驱动直径20μm、长2cm的铝丝电爆炸形成铝丝蒸气。快电流前沿、小丝直径和较短的丝长度有助于提高负载中的单位质量沉积能量,容易电爆炸形成金属蒸气负载。     

Experimental study of V–I characteristics of wire–plate electrostatic precipitators under clean air conditions

In this paper a laboratory-scale model for prediction of the voltage–current characteristics of wire–plate electrostatic precipitators under clean air conditions is presented and experimentally validated. The model investigates the effect of electrode configurations, wire diameter, spacing between wire electrodes, number of discharge wires and distance between collecting plates that on voltage–current characteristic of wire–plate electrostatic precipitators. Also, this paper presents a simulation model, based on the Finite Difference Method (FDM), to simulate electric conditions of wire–plate electrostatic precipitators under clean air conditions. The experimental results of some models are compared with those obtained from the simulation models.     

Analysis of a hollow-cathode reflex discharge in a hydrocarbon flow

Variation of parameters of a reflex discharge with a hollow cathode operating continuously in propane with a flow rate of 1.3–5.6 (m³ mPa)/s and a discharge current of 0.1–0.4 A is analyzed. It is shown that for a hydrocarbon flow rate of 2.4 (m³ mPa)/s and higher, an increase in the discharge voltage takes place after a time interval depending on the discharge current and gas pressure; this is explained by the formation of coating of the dissociation products of hydrocarbon molecules on the electrodes of the discharge chamber. An increase in the thickness of the carbon coating of the cathodes with time and their charging with ions lead to electric breakdown of coatings and the formation of cathode spots. The oscillograms of the discharge current and voltage indicate a short-term transformation of the glow discharge into the arc discharge. The energy spectra of ions emerging from the discharge are measured, and the effect of the discharge current and the gas flow rate on the energy spread of ions is analyzed. The operation time of the discharge in hydrocarbon after which the cleaning of the discharge chamber is required is determined. The possibility of using an ion source based on the reflex discharge with a hollow cathode for technological purposes is established.     

真空及空气中金属丝电爆炸特性研究

开展了铝丝在真空和空气环境中的电爆炸特性研究.从金属丝电爆炸的电压、电流波形得到了金属丝内的沉积能量,并基于以上电参数特征分析了电爆炸产物的状态,获得了空气中铝丝电爆炸电流暂停时间随初级储能电容充电电压的变化规律.真空和空气中铝丝电爆炸在电压击穿时刻的沉积能量分别为2.8和6 eV/atom.采用波长为532 nm、亚纳秒激光探针对金属丝电爆炸物理过程开展了高时空分辨率的阴影和纹影诊断.阴影图像清晰地展示了不同气氛环境中高密度电爆炸产物的膨胀过程,根据光学诊断图像分析了高密度丝核沉积能量的结构和空气中铝丝电爆炸产生的激波的膨胀轨迹.真空和空气环境中高密度电爆炸产物的平均膨胀速度分别为1.9和3 km/s.基于实验数据和输运参数模型,估算了金属丝在电压击穿时刻的温度.     

Stability and energy efficiency of pulsed corona discharge in treatment of dispersed high-conductivity aqueous solutions

Pulsed corona discharge (PCD) is an energy-efficient method of water treatment, although its instability in treatment of conductive solutions showered onto the electrodes presents a problem. The impact of conductivity and gaseous ozone concentration on the discharge stability and the energy transfer efficiency was established. The discharge was stabilized by adjusting the voltage pulse shape. Energy dissipation increases with the treated solution conductivity due to ohmic losses reaching 30% of the energy delivered to the reactor at 45 mS cm⁻¹. The PCD energy efficiency and safety was improved by the modified electrode system design reducing the losses.     

基于Kriging模型的水中放电沉积能量优化分析

水中脉冲放电过程较为复杂,放电参数与放电沉积能量之间没有明确的函数关系。为了获得最佳沉积能量,明晰不同放电参数相互作用对沉积能量的影响,获得最佳放电参数组合,本文搭建了水中高压脉冲放电实验平台,结合Kriging代理模型探究了电压、电极间距和电导率三种放电参数对水中放电沉积能量的影响;利用遗传算法进行全局寻优,确定了最佳放电参数组合。研究结果表明：通过交叉验证评估该模型的均方根误差为6.95%,满足精度要求;外加电压一定时,在电极间距和电导率的协同作用下,沉积能量的变化呈现多峰值特性;在电压、电极间距和电导率分别为17 kV、2.28 mm和0.8 mS/cm的条件下产生的沉积能量最大,为最佳参数组合;通过实验验证了在最佳点的预测值和实际值相对偏差在8%以内。     

丝阵负载Z箍缩早期过程的研究

利用X箍缩等离子体产生的μm级、亚ns脉冲X射线点源对双丝电爆炸过程进行了X射线背光照相,结果表明:真空环境下爆炸丝通常形成“核冕”结构,即高密度丝核表面围绕着低密度冕等离子体;随后在全局磁场驱动下,冕层将被连续剥离并向轴线汇聚,形成“先驱等离子体”,大大降低丝阵的内爆品质。针对上述问题,进一步对实现“无核丝爆”(提高丝核沉积能量实现金属丝的均匀汽化)的方法进行了研究。实验结果表明:提高驱动电流上升率以及在金属丝表面构造正向径向电场均有利于丝核沉积能量的提高。结合上述两种方法,提出了阴极串联闪络开关的电极构型,大幅度提高了丝核沉积能量:正负极性驱动电流下比能量分别提高到原来的2倍(从5.7 eV/atom到13 eV/atom)和3.5倍(3.4 eV/atom到12 eV/atom),均超过了钨丝汽化能(8.8 eV/atom),且激光干涉图像表明爆炸产物具有很高的汽化率,即实现了“无核丝爆”。     

Research on the influence of conductivity to pulsed arc electrohydraulic discharge in water

Pulsed arc electrohydraulic discharge (PAED) is a kind of thermal plasma arc discharge phenomenon which can generate strong pressure wave, ultraviolet ray and active groups. Therefore, PAED can act as a significant role applying on the technology of water treatment and it has broad application prospects. Compared with the existing water treatment mechanism, the technology of PAED possesses the most sterilization efficient and no secondary pollution. There are a huge number of plasma, active groups and gas liquid mixtures generated between the two arc electrodes in the water medium when the streamer discharge voltage is 3∼5 kV. In addition, water conductivity is also changed with the development of pulse arc electrohydraulic discharge which should be the prime importance in the process of PAED. In this article, firstly we analyzed the discharge mechanism on the process of pulsed arc electrohydraulic discharge. After that how the conductivity had played a major role in the process of pre-breakdown discharge and the main discharge processes will be discussed in detail. Experiments were conducted to research the relation among the conductivity, the pressure wave, active groups, ultraviolet light, discharge current and voltage generated from PAED. In finally the result can become a basis for using the water treatment tech of pulsed arc electrohydraulic discharge on different conductivity.     

一种自放电双锥天线激励电压的测量方法

采用一种通过测量脉冲源对天线的充电电流,来间接测量天线放电激励电压的方法。首先建立了实际电路的理论仿真模型,通过理论仿真证明了该方法的可行性。然后在双锥天线的不同绝缘工作气压下,对其充电电流进行了测量。由天线的充电电流推导出了在不同工作气压下天线的电压波形和放电激励电压。该种方法无需对天线进行改造,不会引进寄生参数,不会影响被试对象的工作状态,且在工程上易于实现。     

Glow discharge cleaning of vacuum switch tubes

To clean the surfaces of parts inside a vacuum-switch tube (VST) the authors propose a technique which generates a glow discharge between the inner electrodes and the copper grid surrounding it. Photographic observation reveals that the glow discharge spreads out and cleans the whole surface inside the VST. A breakdown test between the inner electrodes shows the effect of the cleaning with this technique. Higher breakdown voltage between the inner electrodes is attained by performing this glow discharge cleaning in argon rather than hydrogen gas. The difference of the cleaning effect seems to be attributed to that of the energy transfer from ion species to the adsorbed molecules and microprotrusions on the surfaces     

The binding of CO molecule with small Wn(n = 2−9) clusters: a DFT investigation

The effect of water conductivity on electrospraying of water was studied in combination with positive DC corona discharge generated in air. We used a point-to-plane geometry of electrodes with a hollow syringe needle anode opposite to the metal mesh cathode. We employed total average current measurements and high-speed camera fast time-resolved imaging. We visualized the formation of a water jet (filament) and investigated corona discharge behavior for various water conductivities. Depending on the conductivity, various jet properties were observed: pointy, prolonged, and fast spreading water filaments for lower conductivity; in contrast to rounder, broader, and shorter quickly disintegrating filaments for higher conductivity. The large acceleration values (4060 m/s² and 520 m/s² for 2 μS/cm and 400 μS/cm, respectively) indicate that the process is mainly governed by the electrostatic force. In addition, with increasing conductivity, the breakdown voltage for corona-to-spark transition was decreasing.