复合材料夹层板的振动及阻尼分析

本文对复合材料夹层板的动态问题提出了一种新的位移修正模式，该位移模式包括了面板的横向剪切变形及夹芯的剪切变形，以此位移模式进行了有限元分析，给出了形成阻尼矩阵的方法。文中还分析了夹层板的阻尼比ψ与夹芯厚度ｈｃ，夹芯材料的阻尼损耗因子β以及夹芯剪切模量Ｇ之间的关系；算例与实验结果的对比表明：本文提出的计算方法可以给出满意的数值结果。     

基于双曲面蜂窝夹层结构等效模型的研究及数值分析

蜂窝夹层结构在轻量化设计领域一直备受关注,相关的理论研究也日趋完善.然而,很多研究主要集中在平面蜂窝夹层结构上,而对于曲面结构的相关研究甚少.本文对双曲面蜂窝夹芯进行了力学分析,建立了曲面蜂窝夹层板的等效力学模型,同时建立了双曲面蜂窝夹层板详细模型和基于三明治夹层板理论以及曲面夹层板理论的等效模型,最后通过有限元方法对...     

用于多种夹层板等效的有限元分析法

针对夹层板力学性能解析法难于计算复杂结构的夹层板且通用性差的问题,本文采用有限元分析法研究了夹层板性能的等效方法。对夹层板的代表体单元模型施加位移约束,模拟弯曲变形时线性独立的应变分量和弯曲内力;根据夹层板内力与应变的本构关系,求出刚度矩阵;最后由刚度矩阵得出宏观等效弹性常数,从而把夹层板等效成连续材料的单层板单元。将该方法与解析法计算结果进行比较得到的夹层板单元四个主要弹性常数误差在0.2%以内,验证了该方法的有效性;另外采用该方法等效三种典型结构夹层板,比较实际模型和等效模型的弯曲响应,得到的误差均在1.4%以内,表明该方法在不考虑复杂多变的夹芯结构时具有通用性。     

四边简支硬夹芯夹层板的弯曲问题研究

现有的夹层结构理论都是将夹芯视为软夹芯,忽略了其面内应力分量和弯曲刚度.该理论不能满足近年来出现的硬夹芯夹层结构.对此,考虑了以上被忽略的因素,修正了Reissner理论的软夹芯假设,提出了考虑夹芯面内应力分量和弯曲刚度的硬夹芯夹层板基本假设.根据最小势能原理得到了硬夹芯夹层板弯曲的基本方程和边界条件,给出了四边简支硬夹芯夹层板在横向载荷下弯曲的解析解.另外本文还研究了硬夹芯夹层板弯曲问题的有限元法,推导了四节点四边形等参单元的有限元列式,并用MATLAB编程求解了具体算例.     

正交复合材料面层夹层板非线性理论及应用

针对复合材料面层夹层板的构造和变形特点，考虑横向剪应力在面层和芯层粘结处的连续条件，应用Ｈａｍｉｌｔｏｎ原理建立了基于五个未知函数的正交铺设复合材料面层夹层板的非线性精化理论。对静力学问题，控制方程化简为由四个基本未知函数表述。文中还分析了简支正交铺设复合材料面层夹层板的非线性弯曲，给出了载荷—挠度特征关系和板中应力的分布状况。数值计算表明，夹层板面层和芯层粘结处的层间剪应力在工程设计中是十分重要的。     

曲壁蜂窝夹层板的振动特性研究

曲壁蜂窝具有负刚度特性,可以在大变形过程中吸收能量、抗冲击,并且在冲击过后可以自我恢复而不像传统蜂窝被压溃。本文将曲梁构成的负刚度蜂窝作为芯层,建立夹层板的动力学模型;推导出了曲壁负刚度蜂窝胞元的等效弹性参数,将其周期性排列为蜂窝芯,应用Reddy高阶剪切变形理论、Von-Karman大变形关系和Hamilton原理推导了负刚度蜂窝夹层板的非线性动力学方程;应用Navier法计算了四边简支边界条件下的固有频率。并利用有限元软件ABAQUS建立模型,计算固有频率,与理论计算结果进行比较,结果显示二者的计算结果具有较好的一致性,验证了芯层等效弹性参数及模型的有效性。探讨了在蜂窝胞元具有较高吸能情形下,夹层板在不同芯层厚度、不同芯厚比以及不同胞元曲壁厚度时的固有频率的变化特性。     

复合材料夹芯壳的振动分析

提出一种改进的一阶剪切变形理论，用于分析复合材料夹芯壳的动力问题，通过有限元分析，得到了夹芯壳振动的动力方程，给出了处理阻尼矩阵的方法，数值分析与实验结果的对比表明计算具有较好的精度，本文的最后给出了减振效果受夹芯剪切模量Ｇ、阻尼损耗因子β和夹芯厚度ｈｃ等因素的影响曲线，可作为优化设计的参考。     

类桁架夹层板的等效弹性常数研究

从应变能等效出发,将具有周期性分布的夹层板的类桁架夹芯与各向异性连续材料等效,给出了相应的宏观等效弹性常数,进而用有限元方法计算了实际夹层板和等效夹层板的结构响应,用一个算例证明了该文方法的有效性.通过对类桁架夹芯的等效弹性常数的计算,结果表明该文方法可以得到较为准确的等效弹性常数,且较其它类型的均匀化方法大大降低了计算量.     

基于Layerwise离散层理论的复合材料夹层板屈曲分析

复合材料夹层结构由于面板和芯层力学特性差异较大,屈曲分析时要分层考虑各层的剪切变形。基于Reddy的Layerwise离散层理论,假设每一层变形服从一阶剪切变形理论,在统一的位移场描述下,推导建立了一种用于复合材料夹层结构屈曲分析的四节点四边形板单元,并采用混合插值方法对单元的剪切锁定进行了修正。分别对三种典型的夹层板结构进行线性屈曲有限元分析,并将计算结果与文献中已有结果进行了对比。结果表明：本文的分析方法能离散考虑各层的力学特性,将结构离散为多层时,计算结果与三维弹性理论或高阶板理论吻合;将结构等效为单层时,计算结果与基于一阶剪切变形理论的文献结构吻合,验证了单元的有效性。     

基于高阶变形理论的夹层板的弯曲与振动

考虑面板和夹芯的面内刚度和横向剪切刚度以及抗弯刚度,考虑了高阶剪切变形,根据横向剪应变分布情况给出横向剪切转角的位移函数,基于哈密尔顿原理,推导了基于高阶变形理论、适用于软、硬夹芯情况夹层板的基本方程。作为算例,以四边简支条件下的夹层板的弯曲与振动,在不同的面板与芯层的弹性模量比和厚度比下进行了计算,并与Reissner理论、Hoff理论以及邓宗白基于Reissner理论的修正模型的计算结果进行了对比。与前述理论与方法相比,本文方法考虑因素更为全面,对夹层板的适用范围更为广泛,计算结果更为精确。针对Nastran软件计算夹层板的振动问题,对其适用范围作了简要分析。     

孔结构金属复合夹芯板抗爆炸冲击响应及吸能特性研究

采用有限元方法研究爆炸载荷下四边固支孔结构金属复合夹芯板的动力响应及吸能特性,给出了孔结构金属复合夹芯板的动力响应过程,得到夹芯板的变形模式,比较了孔结构金属复合夹芯板与非孔结构金属复合夹芯板的抗爆炸冲击性能,同时讨论了孔大小、间距、排布方式和面板质量分布等因素对孔结构金属复合夹芯板抗爆炸冲击性能的影响。研究结果表明,迎爆面外面板的孔设计使爆炸冲击波穿过孔洞直接作用在芯材上,增强了芯材的压缩,从而提高了夹芯板的能量吸收能力。同等面密度情况下,内外面板厚度比大于1的孔结构金属复合夹芯板变形挠度小于内外面板厚度比小于1的孔结构金属复合夹芯板。进一步研究发现,通过合理设计内外面板的质量分布,可以使孔结构金属复合夹芯板的抗爆炸冲击性能最优。     

撞击载荷下泡沫铝夹层板的动力响应

应用泡沫金属子弹撞击加载的方式研究了固支方形夹层板和等质量实体板的动力响应,分别应用激光测速装置和位移传感器测量了泡沫子弹的撞击速度和后面板中心点的位移历史,给出了夹层板的变形与失效模式,研究了子弹冲量、面板厚度、泡沫芯层厚度及芯层密度对夹层板抗撞击性能的影响。结果表明,后面板中心点挠度最大,周边最小,整体变形为穹形,且伴有花瓣形的变形。参数研究表明,通过增加面板厚度或芯层厚度均能有效控制后面板的挠度,改善夹层板的能量吸收能力,结构响应对子弹冲量和芯层密度比较敏感。实验结果对多孔金属夹层结构的优化设计具有一定的参考价值。 更多还原     

Point-wise impulse (blast) response of a composite sandwich plate including core compressibility effects

This work analyzes the nonlinear impulse response of a composite sandwich plate exposed to a sudden point-wise transverse loading on the top face sheet. The nonlinearity arising from the core compressibility in the thickness direction is modeled and incorporated into the constitutive relations explicitly. As such, one can have a deep insight regarding the stress, strain and displacement profiles into the sandwich plate. The sandwich plate is assumed to be perfectly bonded at the face sheet/core interfaces. The equations of motion are formulated using Hamilton’s principle. The simply supported case is used to illustrate the procedure for solving the nonlinear equations. Numerical results are presented to demonstrate the response in terms of the transverse deformation and stresses in the composite sandwich plate. The effects of the variation of the geometrical parameters of the structure on the blast impulse response are also studied. Some conclusions are suggested regarding the associated optimal design of sandwich plates.     

Buckling analysis of sandwich plates with FGM face sheets resting on elastic foundation with various boundary conditions: an analytical approach

This paper presents an analytical investigation on the buckling analysis of symmetric sandwich plates with functionally graded material (FGM) face sheets resting on an elastic foundation based on the first-order shear deformation plate theory (FSDT) and subjected to mechanical, thermal and thermo-mechanical loads. The material properties of FGM face sheets are assumed to be graded in the thickness direction according to a simple power law distribution in terms of the volume fractions of the constituents. The core layer is still homogeneous and made of an isotropic material. An analytical approach is used to reduce the governing equations of stability and then solved using an analytical solution which is named as power series Frobenius method for symmetric sandwich plates with six different boundary conditions. A detailed numerical study is carried out to examine the influence of the plate aspect ratio, side-to-thickness ratio, loading type, sandwich plate type, volume fraction index, elastic foundation coefficients and boundary conditions on the buckling response of FGM sandwich plates. This has not been done before and serves to fill the gap of knowledge in this area.     

Static and free vibration analysis of four-parameter continuous grading elliptical sandwich plates

In the present study, the static and dynamic analyses of elliptical functionally graded sandwich(FGS) plates are investigated. The constituent materials of the sandwich plates are ceramic and metal so that the core is made of pure metal, while the face sheets consist of a combination of metal and ceramic according to a four-parameter power-law distribution. Different material profiles such as classic, symmetric, and asymmetric can be obtained using the applied generalized power-law distribution ...     

Elasto-plastic buckling and post-buckling analysis of sandwich plates with functionally graded metal-metal face sheets and interfacial damage简

Based on the elasto-plastic theory, considering the effect of spherical stress tensor on the elasto-plastic deformation and using the slicing treatment to deal with the plasticity of functionally graded coatings, the elasto-plastic increment constitutive equations of the sandwich plates with functionally graded metal-metal face sheets can be derived. Applying the weak bonded theory to the interfacial constitutive relation and taking into account the geometric nonlinearity, the nonlinear increment differential equilibrium equations of the sandwich plates with functionally graded metal-metal face sheets are obtained by the minimum potential energy principle. The finite difference method and the iterative method are used to obtain the post-buckling path. When the effect of geometrical nonlinearity of the plate is ignored, the elasto-plastic critical buckling load of the sandwich plates with functionally graded metal-metal face sheets can be solved by the Galerkin method and the iterative method. In the numerical examples, the effects of the interface damages, the induced load ratio, the functionally graded index, and the geometry parameters on the elasto-plastic post-buckling path and the elasto-plastic critical buckling load are investigated.     

Dynamic response of composite sandwich plates subjected to time-dependent pressure pulses

The dynamic response of orthotropic sandwich composite plates impacted by time-dependent external blast pulses is studied by use of numerical techniques. The theory is based on classical sandwich plate theory including the large deformation effects, such as geometric non-linearities, in-plane stiffness and inertias, and shear deformation. The equations of motion for the plate are derived by the use of the virtual work principle. Approximate solutions are assumed for the space domain and substituted into the equations of motion. Then the Galerkin Method is used to obtain the non-linear differential equations in the time domain. The finite difference method is applied to solve the system of coupled non-linear equations. The results of theoretical analyses are obtained and compared with ANSYS results. Effects of the face sheet number, as well as those related to the ply-thickness, core thickness, geometrical non-linearities, and of the aspect ratio are investigated. Detailed analyses of the influence of different type of pressure pulses on dynamic response are carried out.     

Analysis and active control of nonlinear vibration of composite lattice sandwich plates

This paper is devoted to investigate the nonlinear vibration characteristics and active control of composite lattice sandwich plates using piezoelectric actuator and sensor. Three types of the sandwich plates with pyramidal, tetrahedral and Kagome cores are considered. In the structural modeling, the von Kármán large deflection theory is applied to establish the strain–displacement relations. The nonlinear equations of motion of the structures are derived by Hamilton’s principle with the assumed mode method. The nonlinear free and forced vibration responses of the lattice sandwich plates are calculated. The velocity feedback control (VFC) and H_∞ control methods are applied to design the controller. The nonlinear vibration responses of the sandwich plates with pyramidal, tetrahedral and Kagome cores are compared. The influences of the ply angle of the laminated face sheets, the thicknesses of the lattice core and face sheets and the excitation amplitude on the nonlinear vibration behaviors of the sandwich plates are investigated. The correctness of the H_∞ control algorithm is verified by comparing with the experiment results reported in the literature. The controlled nonlinear vibration response of the sandwich plate is computed and compared with that of the uncontrolled structural system. Numerical results indicate that the VFC and H_∞ control methods can effectively suppress the large amplitude vibration of the composite lattice sandwich plates.

     

A lattice deformation based model of metallic lattice sandwich plates subjected to impulsive loading

A lattice structure deformation mechanism based theoretical model is developed to predict the dynamic response of square lattice sandwich plates under impulsive loading. The analytical model is established on the basis of the three-stage framework proposed by Fleck and Deshpande (2004). In the first stage, the impulse transmitted from air shock loading to the sandwich plates by fluid-structure interaction is analytically calculated. The lattice core suffers non-uniform compression in the second stage due to the clamped boundary conditions. The structure deformation mechanism is introduced in the lattice core compression and the analytical nominal stress–strain curve of core compression accords well with previous experimental results. In the final stage, the sandwich plate is analyzed as a continuum plate with non-uniform thickness deduced by inconsistent deformation of the front and back sheets.The experiment results of square metallic sandwich plates with tetrahedral lattice core are presented and compared with analytical prediction to validate the theoretical model. Good agreements are found between the predicted and testing results for both the impulse transmitted to the sandwich plates and the maximum deflection of the back face sheet.     

PVC夹芯板在冲击载荷下的动态响应与失效模式

通过开展对泡沫金属子弹撞击加载聚氯乙烯(polyvinyl chloride, PVC)夹芯板的实验,结合三维数字图像相关性(three dimensional digital image correlation, DIC-3D)技术,研究固支夹芯板在撞击加载条件下的动态响应,获得夹芯板受撞击及响应的变形过程,并结合图像分别分析夹芯板整体及三层结构的变形和失效模式;研究子弹冲量与背板最终变形之间的关系和相似冲量下等面密度不同芯层密度的夹芯结构的抗撞击性能。结果表明:夹芯板的破坏和失效主要集中在泡沫金属子弹直接作用区域,背板挠度由中间向固定端逐渐减小,子弹冲量与背板变形近似成线性关系。在等质量的条件下,降低芯层密度、增加芯层厚度可以有效降低背板的变形,实验结果对聚合物夹芯结构的工程优化设计具有一定的参考意义。