Effect of Pt,Pd, and Cs<Superscript>+</Superscript> Additives on the Surface State and Catalytic Activity of WO<Subscript>3</Subscript> in Oxidation of Hydrogen

We have shown that additions of Pt(Pd) and Cs⁺ to WO₃ significantly increase its specific surface area and catalytic activity in H₂ oxidation. After reduction, the promoted specimens contain the phases WO₃, WO_2.9, H_xWO₃; and in the case of Cs⁺ additions, Cs_xWO₃. According to X-ray photoelectron spectroscopy (XPS), the Pt and Pd have an oxidation state close to 0, while tungsten has a +5 oxidation state. The W:O ratio indicates the content of oxygen vacancies in the surface layer. The data are explained taking into account hydrogen spillover from Pt(Pd) to the support.__________Translated from Teoreticheskaya i Eksperimental’naya Khimiya, Vol. 41, No. 2, pp. 126–129, March– April, 2005.     

Catalytic Activity of WO<Subscript>3</Subscript> and MoO<Subscript>3</Subscript> with Pt and Pd Additives in Oxidation of Hydrogen

We have shown that WO₃ and MoO₃ with Pt or Pd additives exhibit high catalytic activity in the reaction of H₂ oxidation. In the temperature range 313 K to 353 K, we have studied the kinetic behavior of the reaction on 0.1 mass % Pt(Pd)/WO₃ and Pt(Pd)/MoO₃ samples. We have established that the kinetics of H₂ oxidation on these catalysts correspond to an Eley - Rideal mechanism. __________ Translated from Teoreticheskaya i Eksperimental'naya Khimiya, Vol. 41, No. 5, pp. 313–316, September–October, 2005.     

Detection of liquid petroleum gas using mixed nanosized tungsten oxide-based thick-film semiconductor sensor

The thick-film semiconductor sensor for liquid petroleum gas (LPG) detection was fabricated using a mixed WO₃-based sensor. We present the characterization of both their structural properties by means of XRD measurements and the electrical characteristics by using gas-sensing properties. The sensing characteristics such as sensitivity, working range, cross-sensitivity and response time were studied by using nanosized WO₃-based mixed with different metal oxides (SnO₂, TiO₂ and In₂O₃) and doped with noble metals (Au, Pd and Pt). The WO₃-based mixed with 5 wt.% In₂O₃ and 0.5 wt.% Pd showed the higher sensing characteristic at low concentration of LPG sensor at an operating temperature 225 °C.     

球状MoS2/WO3复合半导体制备及其对RhB的光催化性能

采用水热法成功制备了MoS₂/WO₃复合半导体光催化剂,分别通过SEM、TEM、EDS、XRD、Raman和DRS对催化剂的形貌,组成及结构进行表征,并用BET模型计算比表面积。对比发现球状MoS₂/WO₃对罗丹明B（RhB）的光降解效率明显高于纯WO₃、片状MoS₂/WO₃复合半导体。针对球状MoS₂/WO₃复合半导体,分别研究了MoS₂不同负载量（0.5%,1%,2%,5%,10%）对RhB光催化降解性能的影响,结果表明MoS₂含量为2%时催化效果最佳。同时,研究了溶液的pH值（pH=1,3,6,7,11）对光催化降解反应活性的影响,结果显示pH=6时降解率最高。当催化剂量增加到1 g·L^-1时,30min后RhB降解率达到96.6%。球状MoS₂/WO₃的瞬态光电流为0.050 6 mA·cm^-2,比纯WO₃提高了2.4倍。经过5次循环实验,球状MoS₂/WO₃复合半导体催化剂仍能保持90%的高降解率。     

球状MoS_2/WO_3复合半导体制备及其对RhB的光催化性能

采用水热法成功制备了MoS_2/WO3复合半导体光催化剂,分别通过SEM、TEM、EDS、XRD、Raman和DRS对催化剂的形貌,组成及结构进行表征,并用BET模型计算比表面积。对比发现球状MoS_2/WO3对罗丹明B(Rh B)的光降解效率明显高于纯WO3、片状MoS_2/WO3复合半导体。针对球状MoS_2/WO3复合半导体,分别研究了MoS_2不同负载量(0.5%,1%,2%,5%,10%)对Rh B光催化降解性能的影响,结果表明MoS_2含量为2%时催化效果最佳。同时,研究了溶液的p H值(p H=1,3,6,7,11)对光催化降解反应活性的影响,结果显示p H=6时降解率最高。当催化剂量增加到1 g·L-1时,30 min后Rh B降解率达到96.6%。球状MoS_2/WO3的瞬态光电流为0.050 6 m A·cm-2,比纯WO3提高了2.4倍。经过5次循环实验,球状MoS_2/WO3复合半导体催化剂仍能保持90%的高降解率。     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

磁性纳米Pd/Fe3O4催化剂的制备及其在Heck反应中的应用

通过使用聚乙烯吡咯烷酮作为稳定剂,合成了磁性Pd/Fe₃O₄纳米颗粒催化剂。对该催化剂进行粉末X射线衍射、透射电子显微镜、感应耦合等离子体和磁性表征。将Pd/Fe₃O₄催化剂用于Heck反应,检测其催化性能。测试结果表明Pd纳米颗粒负载在Fe₃O₄纳米颗粒上,而且催化剂的尺寸<20 nm,并在Heck反应中表现了极好的催化性能。此外,催化剂可以通过磁场回收利用, 且催化活性没有显著的降低。     

Nox reduction with CO over supported Pd catalysts under simulated post Euro-IV diesel exhaust conditions

The catalytic reduction of NO_x with CO over Pd/Al₂O₃ and Pd/TiO₂/Al₂O₃ under simulated post Euro-IV diesel exhaust conditions was studied. The catalytic activities obtained by using various Pd and TiO₂ loadings and total amounts of reductant and the influence of H₂ and H₂O was investigated.     

Pd@GO/Fe3O4/PAA/DCA: a novel magnetic heterogeneous catalyst for promoting the Sonogashira cross-coupling reaction

Abstract

A hybrid system involving graphene oxide (GO), magnetic oxide (Fe₃O₄), acrylamide and dicyandiamide was prepared via amine functionalization of GO/Fe₃O₄ by means of covalent bonding with acrylamide and subsequent reaction with dicyandiamide to provide a multinitrogen containing polymer on the surface of GO. This hybrid system was utilized as a heterogeneous catalyst support for immobilizing Pd nanoparticles to provide the hybrid, Pd@GO/Fe₃O₄/PAA/DCA. This nano-Pd composite was characterized using Fourier transform infrared, transmission electron microscopy, scanning electron microscopy, vibrating sample magnetometer, thermogravimetric analysis, X-ray diffraction, and ICP techniques and used for promoting Sonogashira cross-coupling under mild reaction conditions. This heterogeneous and magnetic catalyst was easily separated by external magnet and was reused in a model reaction, efficiently up to six times with slight loss of catalytic activity and Pd leaching, showing the suitability of GO/Fe₃O₄/PAA/DCA for embedding Pd nanoparticles. To check the effect of the number of surface nitrogens of the polymeric chain on the catalytic performance, the activity of the catalyst was compared with Pd@GO/Fe₃O₄/PAA; increased number of the surface nitrogens on the chain polymer leads to higher loading of Pd and lower the Pd leaching.     

Br-掺杂Bi2WO6的水热法合成及其可见光催化性能

以Bi（NO₃）₃·5H₂O和Na₂WO₄·2H₂O为主要原料,采用水热法合成了纯相Bi₂WO₆,并对其进行非金属离子Br^-掺杂改性。采用XRD、SEM、TEM、XPS、Raman、PL和DRS研究了Br^-掺杂对Bi₂WO₆的物相结构、形貌和可见光催化性能的影响。结果表明,Br^-掺杂可有效提高Bi₂WO₆的可见光催化性能,当掺杂量（物质的量百分数）为8%时,溴掺杂Bi₂WO₆的光催化性能最好,可见光照射40 min后,可降解96.73%的罗丹明-B,与未掺杂Bi₂WO₆相比,其降解率提高了36.32%。     

Br~-掺杂Bi_2WO_6的水热法合成及其可见光催化性能

以Bi(NO_3)_3·5H_2O和Na_2WO_4·2H_2O为主要原料,采用水热法合成了纯相Bi_2WO_6,并对其进行非金属离子Br-掺杂改性。采用XRD、SEM、TEM、XPS、Raman、PL和DRS研究了Br~-掺杂对Bi_2WO_6的物相结构、形貌和可见光催化性能的影响。结果表明,Br-掺杂可有效提高Bi_2WO_6的可见光催化性能,当掺杂量(物质的量百分数)为8%时,溴掺杂Bi_2WO_6的光催化性能最好,可见光照射40 min后,可降解96.73%的罗丹明-B,与未掺杂Bi_2WO_6相比,其降解率提高了36.32%。     

Preparation and visible light photocatalytic activity of Bi2O3/Bi2WO6 heterojunction photocatalysts

The Bi₂O₃/Bi₂WO₆ heterojunction photocatalysts were prepared by a two-step solvothermal process using Bi(NO₃)₃-ethylene glycol solution as Bi source. The catalysts were characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis diffuse reflection spectroscopy. The heterostructure catalysts are composed of Bi₂O₃ nanoparticles as modifier and 3D Bi₂WO₆ microspheres as substrate. Bi₂O₃ nanoparticles with diameters of about 10-15 nm are tightly grown on the lateral surface of the Bi₂WO₆ microspheres. The hierarchical Bi₂O₃/Bi₂WO₆ microspheres exhibit higher photocatalytic activity than the single phase Bi₂WO₆ or Bi₂O₃ for the degradation of rhodamine B under visible light illumination (λ>420 nm). The enhancement of the photocatalytic activity of the Bi₂O₃/Bi₂WO₆ heterojunction catalysts can be ascribed to their improved light absorption property and the reduced recombination of the photoexcited electrons and holes during the photocatalytic reaction. The effect of loading amount of Bi₂O₃ on the catalytic performance of the heterojunction catalysts was also investigated and the optimal content of Bi₂O₃ is 3 wt%. The Bi₂O₃/Bi₂WO₆ heterojunction photocatalysts are essentially stable during the photocatalytic process.     

Subsolidus phase relations and crystal structures of the mixed-oxide phases in the In2O3-WO3 system

Subsolidus phase relationships in the In₂O₃-WO₃ system at 800-1400°C were investigated using X-ray diffraction. Two binary-oxide phases—In₆WO₁₂ and In₂(WO₄)₃—were found to be stable over the range 800-1200°C. Heating the binary-oxide phases above 1200°C resulted in the preferential volatilization of WO₃. Rietveld refinement was performed on three structures using X-ray diffraction data from nominally phase-pure In₆WO₁₂ at room temperature and from nominally phase-pure In₂(WO₄)₃ at 225°C and 310°C. The indium-rich phase, In₆WO₁₂, is rhombohedral, space group (rhombohedral), with Z=1, a=6.22390(4) Å, α=99.0338(2)° [hexagonal axes: a_H=9.48298(6) Å, c=8.94276(6) Å, a_H/c=0.9430(9)]. In₆WO₁₂ can be viewed as an anion-deficient fluorite structure in which 1/7 of the fluorite anion sites are vacant. Indium tungstate, In₂(WO₄)₃, undergoes a monoclinic-orthorhombic transition around 250°C. The high-temperature polymorph is orthorhombic, space group Pnca, with a=9.7126(5) Å, b=13.3824(7) Å, c=9.6141(5) Å, and Z=4. The low-temperature polymorph is monoclinic, space group P2₁/a, with a=16.406(2) Å, b=9.9663(1) Å, c=19.099(2) Å, β=125.411(2)°, and Z=8. The structures of the two In₂(WO₄)₃ polymorphs are similar, consisting of a network of corner sharing InO₆ octahedra and WO₄ tetrahedra.     

Catalytic methanol decomposition to carbon monoxide and hydrogen over Pd/CeO2-ZrO2-La2O3 with different Ce/Zr molar ratios

The catalytic behaviors of Pd (1.4 wt%) catalysts supported on CeO₂-ZrO₂-La₂O₃ mixed oxides with different Ce/Zr molar ratios were investigated for methanol decomposition. Nitrogen adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS), H₂ temperature-programmed reduction (H₂-TPR), X-ray diffraction (XRD) and Pd dispersion analysis were used for their characterization. Pd/Ce_0.76Zr_0.18 La_0.06O_1.97 catalyst showed the highest BET surface area, best Pd dispersion capability and strongest metal-support interaction. Moreover, XPS showed that there was lattice defect oxygen or mobile oxygen. According to the result of O 1s measurements the lattice defect oxygen or mobile oxygen helped to maintain Pd in a partly oxidized state and increased the activity for methanol decomposition. The Pd/Ce_0.76Zr_0.18La_0.06O_1.97 catalyst exhibited the best activity. A 100% conversion of methanol was achieved at around 260 °C, which was about 20-40 °C lower than other catalysts     

Influence of Pd precursors on the catalytic performance of Pd–H4SiW12O40/SiO2 in the direct oxidation of ethylene to acetic acid

The effects of palladium precursors (PdCl₂, (NH₄)₂PdCl₄, Pd(NH₃)₂Cl₂, Pd(NO₃)₂ and Pd(CH₃COO)₂) on the catalytic properties in the selective oxidation of ethylene to acetic acid have been investigated for 1.0 wt% Pd–30 wt% H₄SiW₁₂O₄₀/SiO₂. The structures of the catalysts were characterized using X-ray diffraction, N₂ adsorption, H₂-pulse chemical adsorption, infrared spectrometry of the adsorbed pyridine, H₂ temperature-programmed reduction and X-ray photoelectron spectroscopy. The present study demonstrates that the different palladium precursors can lead to the significant changes in the dispersion of palladium. It is found that Pd dispersion decreases as follows: PdCl₂ > (NH₄)₂PdCl₄ > Pd(NO₃)₂ > Pd(NH₃)₂Cl₂ > Pd(C₂H₃O₂)₂, which is nearly identical to the catalytic activity. This indicates that the dispersion of palladium plays an important role in the catalytic activity. Furthermore, density of Lewis (L) and Brönsted (B) acid sites are also strongly dependent on the palladium precursors. It is also demonstrated that an effective catalyst should possess a well combination of Brönsted acid sites with dispersion of palladium.     

Ag/Bi2WO6复合材料的制备及光催化性能

采用一步水热合成法制得花球状Bi_2WO_6和Ag/Bi_2WO_6光催化剂,借助X射线衍射(XRD)、场发射扫描电子显微镜(FES-EM)、透射电子显微镜(TEM)、X射线光电子能谱分析(XPS)、紫外-可见分光光度法(UV-Vis)等手段对样品进行结构性能表征。模拟日光的条件下,以甲基橙(MO)为降解物,对Bi_2WO_6和Ag/Bi_2WO_6的催化活性和机理进行研究。结果表明,相对Bi_2WO_6,相同条件下Ag/Bi_2WO_6对MO具有更佳的降解效果,当Ag掺杂量为1%(n/n)时,其降解率(180 min)可达到91.4%,同时一次回收样降解率也达到81%。此外,也对Ag/Bi_2WO_6复合材料的降解机理做了初步探究。     

粉煤灰漂珠负载Bi2WO6复合材料的制备及光催化性能研究

以工业固体废弃物粉煤灰漂珠(fly ash cenospheres,FACs)为载体,采用水热法制备了新颖的漂珠负载Bi2WO6复合材料(Bi2WO6/FACs),通过X射线衍射(XRD),扫描电子显微镜(SEM),X-射线光电子能谱(XPS),和紫外-可见漫反射光谱(DRS)技术对其进行了表征。XRD数据显示了正交相Bi2WO6的特征衍射峰。DRS结果证实了引入FACs后Bi2WO6对可见光的吸收增强。在可见光的照射下,以亚甲基蓝溶液的光催化降解评价了Bi2WO6/FACs复合材料的光催化性能。结果表明:Bi2WO6/FACs的光催化性能优于纯Bi2WO6的,其一级反应速率常数(k)为后者的2.4倍。尤其是由于漂珠质轻中空的特性,Bi2WO6/FACS复合光催化剂可长时间漂浮于水面,既能充分吸收光能,又有利于催化剂的回收和重复利用。     

粉煤灰漂珠负载Bi2WO6复合材料的制备及光催化性能研究

以工业固体废弃物粉煤灰漂珠(fly ash cenospheres, FACs)为载体, 采用水热法制备了新颖的漂珠负载Bi₂WO₆复合材料(Bi₂WO₆/FACs), 通过X射线衍射(XRD), 扫描电子显微镜(SEM), X-射线光电子能谱(XPS), 和紫外-可见漫反射光谱(DRS)技术对其进行了表征。XRD数据显示了正交相Bi₂WO₆的特征衍射峰。DRS结果证实了引入FACs后Bi₂WO₆对可见光的吸收增强。在可见光的照射下, 以亚甲基蓝溶液的光催化降解评价了Bi₂WO₆/FACs复合材料的光催化性能。结果表明：Bi₂WO₆/FACs的光催化性能优于纯Bi₂WO₆的, 其一级反应速率常数(k)为后者的2.4倍。尤其是由于漂珠质轻中空的特性, Bi₂WO₆/FACS复合光催化剂可长时间漂浮于水面, 既能充分吸收光能, 又有利于催化剂的回收和重复利用。     

Selective catalytic reduction of NO with CO on Pt/W–Ce–Zr catalysts

Various Pt catalysts (Pt/ZrO₂, Pt/CeO₂, Pt/CeZrO, Pt/WO₃/ZrO₂ and Pt/WO₃/CeZrO) were prepared and characterized, and their catalytic reduction reactions of NO by CO, with or without the presence of excess oxygen, were investigated. The results of temperature-programmed experiments showed that CO could be easily oxidized over Pt/CeO₂ and Pt/CeZrO while the introduction of WO₃ into the catalyst (Pt/WO₃/CeZrO) inhibited the reduction of catalyst surface; NO could not dissociate over those catalysts in oxidized state but after CO reduction at a low temperature, NO dissociation took place only over Pt/CeO₂ and Pt/CeZrO catalysts. For NO + CO reaction, those easily reduced catalysts Pt/CeO₂ and Pt/CeZrO exhibited better catalytic performances, and NO could be rapidly converted below 350 °C. For the reaction with the presence of excess O₂, the NO conversions were significantly inhibited, but better NO conversions were obtained over the tungstate-contained catalysts when compared with Pt/CeO₂ and Pt/CeZrO. The higher activities of Pt/W–Ce–Zr catalysts were attributed to their high acidities.     

Microwave effects on the oxidative coupling of methane over Bi2O3-WO3 oxygen ion conductive oxides

The oxidative coupling of methane over (Bi₂O₃)_1-x(WO₃)_x (x=0.2, 0.3, 0.4) oxygen ion conductive oxide catalysts irradiated by microwave has been studied. Compared with a conventional heating mode, the temperature of the catalytic bed is much lower with microwave irradiation and there is a change in selectivity favoring the production of C₂ products.