Morphology and crystallinity of particles formed from dilute solutions of poly(vinyl alcohol-b-acrylonitrile), poly(vinyl alcohol) and polyacrylonitrile

The morphology of agglomerates and particles of poly(vinyl alcohol-b-acrylonitrile), poly(vinyl alcohol) (PVA) and polyacrylonitrile (PAN) formed from their dilute solutions and the variation of the morphology with the composition of the block copolymers were examined using transmission electron microscopy. The crystalline nature of these particles was studied by an electron diffraction method. Electron diffraction for copolymers containing AN lower than 30 wt% mainly showed a single-crystal diffraction pattern of the PVA component. With the copolymer containing 38.90 wt% AN, a mixed pattern of a blend of PVA polycrystal and PAN polycrystal as well as a PVA single-crystal pattern were simultaneously observed.     

Dilute solutions of poly(vinyl alcohol) derived from vinyl trifluoroacetate

The dilute-solution behavior of poly(vinyl alcohol) (PVA_VTFA), derived from vinyl trifluoroacetate, in water-dimethylsulfoxide (DMSO) mixtures was investigated. With solvent mixtures ranging from 10 to 20 vol % DMSO, the relation between the reduced viscosity η_sp/C and the polymer concentration C was linear for polymer concentrations above 0.2 g/dL, whereas in solutions in mixed solvents of other compositions the dependence was linear for polymer concentrations above 0.1 g/dL. The relation between the intrinsic viscosity [η] obtained for aqueous solutions of PVA_VTFA and the molecular weight M estimated from viscosity measurements in solutions of poly(vinyl acetate) (PVA_VTFA), obtained by acetylation of PVA_VTFA, was given by [η] = 7.34 × 10^?4 M^0.63. The value of [η] was greatest for the solvent mixture with 10 vol % DMSO and smallest for about 50 vol % DMSO, and Huggins constants k were smallest and greatest for these two cases, respectively. The turbidity of the solutions of low-molecular-weight PVA_VTFA, was higher than that of high-molecular-weight PVA_VTFA up to 30 vol % DMSO, and the reverse relation held for 40-70 vol % DMSO.     

Multilayer poly(vinyl alcohol)-adsorbed coating on poly(dimethylsiloxane) microfluidic chips for biopolymer separation

A poly(dimethylsiloxane) (PDMS) microfluidic chip surface was modified by multilayer-adsorbed and heat-immobilized poly(vinyl alcohol) (PVA) after oxygen plasma treatment. The reflection absorption infrared spectrum (RAIRS) showed that 88% hydrolyzed PVA adsorbed more strongly than 100% hydrolyzed one on the oxygen plasma-pretreated PDMS surface, and they all had little adsorption on original PDMS surface. Repeating the coating procedure three times was found to produce the most robust and effective coating. PVA coating converted the original PDMS surface from a hydrophobic one into a hydrophilic surface, and suppressed electroosmotic flow (EOF) in the range of pH 3-11. More than 1,000,000 plates/m and baseline resolution were obtained for separation of fluorescently labeled basic proteins (lysozyme, ribonuclease B). Fluorescently labeled acidic proteins (bovine serum albumin, beta-lactoglobulin) and fragments of dsDNA phiX174 RF/HaeIII were also separated satisfactorily in the three-layer 88% PVA-coated PDMS microchip. Good separation of basic proteins was obtained for about 70 consecutive runs.     

The solvation of poly(vinyl alcohol)

The possible incorporation of water molecules within the crystal structure of poly(vinyl alcohol) is discussed. Modelling of the crystal structure suggested that water could be incorporated without severe disruption, and the effect on the X-ray powder diffraction trace was simulated. The effect of variation in tacticity is discussed in terms of the nature of the hydrogen bonding. Simulated traces are compared with experimental data from atactic samples in which a change in the diffraction peak intensities is observed for samples crystallised with water present. This is compared with samples produced from nonaqueous solutions.     

Phase behavior and gelation of solutions of poly (vinyl alcohol)

The phase behavior of poly (vinyl alcohol) dissolved in ethylene glycol and propylene glycol was studied. On cooling a solution in the low concentration range, solidification results from a combination of a liquid-liquid demixing and a crystallization or liquid-solid demixing. This conclusion is based on the results obtained from optical and calorimetric observations and is further supported by the influence of the molecular weight and the solvent quality. It also explains the melting point-crystallization relationship observed after isothermal crystallization of the polymer in presence of the solvent. The mechanism proposed for the thermoreversible gelation of these solution is confirmed.     

Heterotactic poly(vinyl alcohol)

Bulky substituents in vinyl trialkylsilyl ethers and vinyl trialkylcarbinyl ethers led to heterotactic polymers (H = 66%). The polymers were converted into poly(vinyl alcohol) (PVA) and further to poly(vinyl acetate), and tacticity was determined as poly(vinyl acetate). Vinyl triisopropylsilyl ether in nonpolar solvents yielded a heterotactic polymer with a higher percentage of isotactic triads than syndiotactic triads (Hetero-I). Vinyl trialkylcarbinyl ethers in polar solvents gave a heterotactic polymer with more syndiotactic triads than isotactic (Hetero-II). Heterotactic PVA was soluble in water and showed characteristics infrared absorptions. Interestingly, Hetero-I PVA showed no iodine color reaction, but Hetero-II showed a much more intense color reaction than a commercial PVA. The mechanism of heterotactic propagation was discussed in terms of the Markóv chain model.     

Chromatography of inorganic anions on poly(vinyl alcohol) gel columns with acidic eluents

Summary Poly(vinyl alcohol) (PVA) gel shows ionic retention properties for common inorganic anions when an acidic eluent is used. The ionic property of the PVA gel is due to the proton-acceptable nitrogen atoms of the cross-linking agent and the carboxylic residues being comprised in the gel matrix. The extent of the net charge on the gel surface depends on the pH of the eluent. At a pH ranging from 2.3 to 5.3, the PVA gel behaves as a weak anion exchanger with very low ion-exchange capacity. At these conditions four UV-absorbing inorganic anions (bromate, bromide, nitrate, and nitrite) are separated by eluting with aqueous sulfuric acid. Alkyl groups introduced on the gel surface hinder the ionized solute molecules from accessing to the positively charged functional groups on the gel surface. A neutral solute (HNO₂) is retained with non-ionic interactions.     

Steric stabilization of thermally responsive N-isopropylacrylamide particles by poly(vinyl alcohol)

Poly(vinyl alcohol) (PVA) was used as a steric stabilizer for the dispersion polymerization of cross-linked poly(N-isopropylacrylamide) (PNIPAM) in water. A series of reactions were carried out using PVA of varying molecular weight and degree of hydrolysis. Under appropriate conditions, PNIPAM particles of uniform and controllable size were produced using PVA as the stabilizer. The colloidal stability was investigated by measuring changes in particle size with temperature in aqueous suspensions of varying ionic strength. For comparison, parallel colloidal stability measurements were conducted on PNIPAM particles synthesized with low-molecular-weight ionic surfactants. PVA provides colloidal stability over a wide range of temperature and ionic strength, whereas particles produced with ionic surfactants flocculate in moderate ionic strength solutions upon collapse of the hydrogel as the temperature is increased. Experimental results and theoretical consideration indicate that sterically stabilized PNIPAM particles resulted from the grafting of PVA to the PNIPAM particle surface. The enhanced colloidal stability afforded by PVA allows the temperature-responsive PNIPAM particles to be used under physiological conditions where electrostatic stability is ineffective.     

The degree of dispersion of poly(vinyl alcohol) in water/n-propanol solutions

It is demonstrated that, although addition of n-propanol to aqueous poly(vinyl alcohol) solutions prevents their aging, the polymer is not present in a molecularly dispersed form. Further, it is shown that viscometry is not a suitable method to study the degree of dispersion of poly(vinyl alcohol) in water or water/n-propanol solution. The results of turbidity measurements as a function of poly(vinyl alcohol) concentration, n-propanol concentration and time suggest that it is a change of solvent quality rather than a specific interaction between polymer and n-propanol that is responsible for the suppression of aging effects.     

The effect of different surfactants on the electrospinning poly(vinyl alcohol) (PVA) nanofibers

The surface tension of the spinning solution is an important parameter in the electrospinning process. Surfactants can change the surface tension of the solution. In this paper, four different kinds of surfactants were added into 10 wt% polyvinyl alcohol/water solution. The effect of different surfactants on the solution properties, the morphology of the resulting mats, the thermal performance, and the inner structure of nanofibers were investigated. The results showed that the surface tension of the spinning solution decreased significantly when the surfactant content was less than 1 %. The viscosity and electric conductivity of the solution increased with the increasing of cationic and anionic surfactant content. The fiber diameter of poly(vinyl alcohol) mats remarkably decreased from 405 to 100 nm as the non-ionic surfactant content within the range of 1 % (v/v) increased. Besides that, the surfactant content also had some influence on the thermal performance and inner structure of nanofibers. With the surfactant content increasing, both the heat of fusions and crystallinity increased significantly.     

Rheological investigation of aqueous solutions of poly(vinyl alcohol) during ageing

The changes in viscosity and normal stress difference during the ageing of concentrated aqueous solutions of poly(vinyl alcohol) prepared at 80 °C and the effect of the procedure used in the preparation of solutions on the course of these changes are described. The results are interpreted by means of shear complianceJ _e and relaxation time ₀.     

The miscibility of poly(vinyl alcohol)/poly(N-vinylpyrrolidone) blends investigated in dilute solutions and solids

Poly(vinyl alcohol) (PVA) (polymer A) and poly(N-vinylpyrrolidone) (PVP) (polymer B) are known to form a thermodynamically miscible pair. In the present study the conclusion on miscibility of PVA/PVP solid blends, confirmed qualitatively (DMTA, FTIR) and quantitatively (DSC, χ_AB = − 0.69 at 503 K) is compared with the miscibility investigations of PVA/PVP solution blends by the technique of dilute solution viscometry. The miscibility of the ternary (polymer A/ polymer B/ solvent) system is estimated on the basis of experimental and ideal values of the viscosity parameters k, b and [η]. It is found that the conclusions on miscibility or nonmiscibility drawn from viscosity measurements in dilute solution blends depend: (i) on the applied extrapolation method used for the determination of the viscosity interaction parameters, (ii) on the assumed definition of the ideal values and (iii) on the thermodynamic quality of the solvent, which in the case of PVA depends on its degree of hydrolysis. Hence, viscometric investigations of dilute PVA/PVP solution blends have revealed that viscometry, widely used in the literature for estimation of polymer-polymer miscibility can not be recommended as a sole method to presume the miscibility of a polymer pair.     

Stabilization of electrospun poly(vinyl alcohol) nanofibrous mats in aqueous solutions

<正>The stability ofpoly(vinyl alcohol)(PVA) nanofibrous mats in water media was improved by post-electrospinning treatments.Bifunctional glutaraldehyde(GA) in methanol was used as a crosslinking agent to stabilize PVA nanofiber,but fiber twinning was observed frequently,and the highly porous structure of PVA nanofibrous mats was destroyed when the crosslinked fiber was soaked in water.To overcome this shortcoming,chitosan(CS) was introduced into the PVA spinning solution to prepare PVA/CS composite nanofibers.Their treatment in GA/methanol solution could retain the fiber morphology of PVA/CS nanofibers and porous structure of PVA/CS nanofibrous mats even if they were soaked in aqueous solutions for 1 month.Scanning electron microscopy(SEM),X-ray diffraction(XRD),thermal gravimetric analysis(TGA) and differential scanning calorimetry(DSC) were applied to characterize the physicochemical structure and thermal properties of PVA nanofibers.It was found that the water resistance of PVA nanofibrous mats was enhanced because of the improvement of the degree of crosslinking and crystallinity in the electrospun PVA fibers after soaking in GA/methanol solution.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

The properties and behavior of supermolecular formations in aging aqueous poly (vinyl alcohol) solutions

The structure of supermolecular formations and the interparticle interaction in aqueous poly(vinyl alcohol) solutions aging at different concentrations were investigated. Integral light scattering was used to determine the single particle scattering functionP(K), the structure functionS(K), and hence the radial distribution functiong(r). Nonrandom arrangement of the supermolecular formations in solutions under study is much less intensive than that of particles in polymer latices.     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

The effect of structural organization on the mechanical strength of poly(vinyl alcohol) gels

Ultimate mechanical properties of poly(vinyl alcohol) adhesive layers prepared from fresh aqueous solution, aged solution and water-swollen PVA particles are compared. Tensile strength and toughness of dry adhesive layers significantly increase in the cited order. These differences may be attributed to the formation of heterogeneous thermoreversible network upon ageing and to the presence of heterogeneities in PVA gel which act as barriers against crack propagation.     

Neighbouring group effect on the kinetics of acetalisation of poly(vinyl alcohol)

A kinetic model for acetalisation of poly(vinyl alcohol) (PVOH) involving a neighbouring group effect has been developed using a statistical approach. Assuming that the acetalisation proceeds irreversibly, an effectiveness factor (defined as the ratio of the concentration of reactable hydroxyl groups to the total concentration of hydroxyl groups of the polymer) has been obtained as a function of conversion. When the effect of neighbouring groups on the reactivity of OH groups is neglected, the model predicts a maximum attainable conversion of 87% which compares well with that postulated by Flory for irreversible acetalisation. Possibilities of conversions > 87%, as reported by some investigators, are discussed. Flory accounted for such higher conversions by postulating reversibility of the acetalisation. Experimental studies reported in the literature, however, indicate the acetalisation to be essentially irreversible. It is shown here that the present model, with the inclusion of the neighbouring group effect, can account for such higher conversions even for irreversible acetalisation of PVOH.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). II. Polymerization of vinyl acetate in the presence of crosslinked poly(vinyl alcohol)

It is a common view that poly(vinyl acetate) has many branches at the acetyl side group, but that the corresponding poly(vinyl alcohol) has little branching. In order to study the branching in poly(vinyl acetate) and poly(vinyl alcohol) which is formed by chain transfer to polymer, the polymerization of ¹⁴C-labeled vinyl acetate in the presence of crosslinked poly(vinyl acetate), which was able to be decrosslinked to give soluble polymers, was investigated at 60°C and 0°C. This system made it possible to separate as well as to distinguish the graft polymer from the newly polymerized homopolymer. Furthermore, the degree of grafting onto the acetoxymethyl group and onto the main chain were estimated. It became clear that, in the polymerization of vinyl acetate, chain transfer to the polymer main chain takes place about 2.4 times as frequently at 60°C as that to the acetoxy group and about 4.8 times as frequently at 0°C.