Synthesis and characterization of Co(OH)<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> nanotube composites as supercapacitor materials

A novel composite of Co(OH)₂ and TiO₂ nanotubes was synthesized by a chemical precipitation method. Co(OH)₂/TiO₂ nanotube composites and its microstructure were characterized by transmission electron microscopy (TEM), X-ray diffraction pattern (XRD). The electrochemical capacitance performance of this composite was investigated by cyclic voltammetry and charge–discharge tests with a three-electrode system in 6 M KOH solution. We synthesized different weight ratios of Co(OH)₂/TiO₂ nanotubes, a maximum specific capacitance of 229 F/g was obtained for the composite. Based on these tests, we propose that TiO₂ nanotubes provide the three-dimensional nanotube network structure for the composite and make the Co(OH)₂ dispersed. For these reasons, the TiO₂ nanotubes used as a framework for Co(OH)₂ improve the utilization of Co(OH)₂ greatly.     

Mesoporous amorphous MnO<Subscript>2</Subscript> as electrode material for supercapacitor

A kind of novel mesoporous, electrochemical active material, amorphous MnO₂ has been synthesized by an improved reduction reaction and using supramolecular as template. The synthesized sample was characterized physically by thermogravimetric analysis, X-ray diffraction, transmission electron microscope (TEM), and Brunauer–Emmett–Teller (BET) surface area measurement, respectively. Electrochemical characterization was performed using cyclic voltammetry and chronopotentiometry in 2 mol/l KOH aqueous solution electrolyte. The results of BET and TEM analysis indicated that supramolecular template plays an important role in the process of big specific surface area mesoporous material forming. After sintering at 200 °C, the sample still remained an amorphous structure, and its specific capacitance reached 298.7 F/g and presented a very stable capacitance after 500 cycles. In addition, the electrochemical process, such as ion transfer and electrical condition, was also investigated with electrochemical impedance spectroscopy.     

Electrochromic properties of WO<Subscript>3</Subscript> and WO<Subscript>3</Subscript>:P thin films

WO₃ and WO₃:P (5 mol% H₃PO₄) thin films were prepared using the sol-gel route and the electrochromic properties of the films were investigated using in situ spectroelectrochemical methods. The measurements were performed in propylene carbonate solution with 0.1 M LiClO₄ as electrolyte. During the cathodic polarization at –0.8 V a blue coloration is observed with a reversible variation between 14% and 84% of the transmittance at λ=633 nm. The kinetics for the bleaching process is faster for the WO₃:P film than for the undoped WO₃ film. Electronic Publication     

Comparison of electrocatalytic characterization of Ti/Sb-SnO<Subscript>2</Subscript> and Ti/F-PbO<Subscript>2</Subscript> electrodes

Electrocatalytic oxidation is a promising process for degrading toxic and biorefractory organic pollutants in wastewater treatment. Selection of electrode materials is crucial for electrochemical oxidation process. In this study, Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes were chosen to compare their electrocatalytic characterization, which were prepared by electrodeposition and thermal decomposition method, respectively. The surface morphology and crystal structure of two electrodes were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The linear polarization curves show that Ti/Sb-SnO₂ electrodes possess higher oxygen evolution overpotential than Ti/F-PbO₂ electrodes. But the stability and corrosion resistance ability of Ti/F-PbO₂ electrode was higher than that of Ti/Sb-SnO₂ electrode. The electrocatalytic activity of Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes was examined for the electrochemical oxidation of malachite green (MG). The bulk electrolysis shows that the Ti/Sb-SnO₂ electrodes exhibit the higher electrocatalytic activity for the degradation of MG than Ti/F-PbO₂ electrodes, and the degradation process is good fitting for the pseudo-first order reaction. The higher electrocatalytic activity of Ti/Sb-SnO₂ electrodes can be attributed to the higher oxygen evolution overpotential.     

Preparation and Characterisation of Nano-Structured WO<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Layers for Photoelectrochromic Devices

Nano-structured WO₃-TiO₂ layers were prepared by the sol-gel route. To obtain transparent, porous and crack free layers up to 0.8 μ m with a single dipping cycle a templating strategy was used. As a template three-dimensionally network based on organically modified silane was introduced to the WO₃ and TiO₂ sols. The WO₃ layers were dip-coated onto the conductive glass substrate (TCO) and the TiO₂ layers on the top of the WO₃ layer. The morphology and the structure of the layers were determined by Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HR-TEM), Energy Dispersive X-Ray Spectroscopy (EDXS), Auger and Infrared spectroscopy. SEM image of the WO₃-TiO₂ layer confirmed the nano-porosity of the layers and give the size of the particles of about 10 nm for TiO₂ and 30 nm for WO₃ layer. Further analysis indicated that the titanium sol penetrates the WO₃ layer. Particles in the WO₃ layer consist of a crystalline monoclinic WO₃ core surrounded by a 5–10 nm amorphous phase consisting of WO₃, TiO₂ and SiO₂. The WO₃-TiO₂ layers were used to assemble all solid state photoelectrochromic (PE) devices. Under 1 sun irradiation (1000 W/m²) the visible transmittance of the PE device changes from 62% to 1.6%. The colouring and bleaching processes last about 10 minutes.     

Synthesis and characterization of macroporous Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C composites as cathode materials for Li-ion batteries

The macroporous Li₃V₂(PO₄)₃/C composite was synthesized by oxalic acid-assisted carbon thermal reaction, and the common Li₃V₂(PO₄)₃/C composite was also prepared for comparison. These samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical performance tests. Based on XRD and SEM results, the sample has monoclinic structure and macroporous morphology when oxalic acid is introduced. Electrochemical tests show that the macroporous Li₃V₂(PO₄)₃/C sample has a high initial discharge capacity (130 mAh g⁻¹ at 0.1 C) and a reversible discharge capacity of 124.9 mAh g⁻¹ over 20 cycles. Moreover, the discharge capacity of the sample is still 91.5 mAh g⁻¹, even at a high rate of 2 C, which is better than that of the sample with common morphology. The improvement in electrochemical performance should be attributed to its improved lithium ion diffusion coefficient for the macroporous morphology, which was verfied by cyclic voltammetry and electrochemical impedance spectroscopy.     

Mutual spontaneous and electrosurface processes at heterophase interfaces WO<Subscript>3</Subscript>|Me<Subscript>2</Subscript>(WO<Subscript>4</Subscript>)<Subscript>3</Subscript> (Me = In,Eu, Sc)

For the first time ever it is demonstrated in this work that, in spontaneous conditions and following the imposition of an electric field, mutual penetration of components of WO₃ and Me₂(WO₄)₃ occurs at heterophase interfaces WO₃|Me₂(WO₄)₃ where Me = In, Eu, or Sc. Tungstic oxide WO₃ is pulled onto the inner surface of ceramic Me₂(WO₄)₃ and, in turn, components of Me₂(WO₄)₃ penetrate onto the surface of grains of ceramic WO₃, which is confirmed by the method of x-ray—fluorescence analysis. Data concerning the conductivity and transport numbers of Eu₂(WO₄)₃ and a composite on its basis, which was manufactured as a result the electrosurface transport of WO₃, are obtained for the first time ever. With allowance made for the data on the O_2? character of the ionic conduction in MeWO₄ and Eu₂(WO₄)₃ it is concluded that the type of ionic carriers in tungstates (Me ⁿ⁺)_2/n [WO₄] makes no impact on the mechanism of spontaneous and field-induced processes that are developing at the (Me ⁿ⁺)_2/n [WO₄]|WO₃ interfaces.     

Thermo-programmed reduction study of Pt/WO<Subscript>x</Subscript>–ZrO<Subscript>2</Subscript> materials by thermogravimetry

The thermo-programmed reduction study of Pt/WO_x–ZrO₂ materials prepared with different tungsten loading were performed by thermogravimetry. The samples were synthesized by impregnation method and calcined at 600, 700 and 800°C. The characterizations of both un-calcined and calcined materials were carried out using different techniques: thermal analysis (TG and DTA), X-ray diffraction (XRD) and thermo-programmed reduction (TPR). TG and DTA analysis of un-calcined were used to determination of calcination temperatures of the samples. XRD diffractograms were useful to help us in the determination of phase presents. TPR profiles showed between three and four events at different temperatures attributed to platinum reduction and the different stages of tungsten specie reduction.     

Tantalum oxide effect on the surface structure and morphology of the IrO<Subscript>2</Subscript> and IrO<Subscript>2</Subscript> + RuO<Subscript>2</Subscript> + TiO<Subscript>2</Subscript> coatings and on the corrosion and electrochemical properties of anodes prepared from these

Alterations in the phase composition, porosity, and surface morphology of coatings are examined following the insertion of a quantity of Ta₂O₅ into active coatings prepared from IrO₂ or IrO₂ + RuO₂ + TiO₂ (OIRTA). It is shown that even an insignificant concentration of Ta₂O₅ in a coating renders it substantially amorphous and leads to the appearance of a large number of wide protracted cracks in the coating. The latter extends the surface of anodes and boosts their apparent catalytic activity in the chlorine evolution reaction. In addition, this accelerates the diffusion of chloride ions toward the front surface of anodes, which noticeably reduces the overvoltage of the chlorine evolution reaction when manufacturing sodium chlorate. The coatings’ amorphization and the development of their surface substantially reduce the corrosion resistance of these anodes as compared with OIRTA.     

NaBO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-Na<Subscript>2</Subscript>WO<Subscript>4</Subscript> quaternary system

This is the first study of the NaBO₂-Na₂CO₃-Na₂MoO₄-Na₂WO₄ quaternary system by differential thermal analysis. Na₂[MoO_4(x)WO_{4(1 − x)}] solid solutions in the quaternary system are found to not decompose.     

Effect of oxygen activity in the gaseous phase on the mechanism of reactions in the solid-state synthesis of In<Subscript>2</Subscript>(WO<Subscript>4</Subscript>)<Subscript>3</Subscript> and In<Subscript>6</Subscript>WO<Subscript>12</Subscript>

The effect of oxygen’s activity on the rate of In₂(WO₄)₃ and In₆WO₁₂ formation reactions was studied to determine the reaction mass transfer mechanism. It was established that the formation of In₂(WO₄)₃ in a model reaction cell is due to the transfer of WO ₄ ^2? components and electrons moving in opposite directions through the reaction product. The relation between the diffusion coefficients of the carriers was found. The rate of electron diffusion and the reaction rate were shown to vary according to the law \(K_p \approx D_{\lim } = D_e \sim a_{O_2 }^{ - 1/4} \). We conclude that the formation of electronic conductor In₆WO₁₂ is a two-region process: at the In₂(WO₄)₃ | In₆WO₁₂ interface, the product is formed on the In₂(WO₄)₃ surface due to {WO₃} escaping toward In₂O₃, and at the In₆WO₁₂ | In₂O₃ interface, the product is formed on the In₂O₃ surface via the reaction of diffuse {WO₃} with In₂O₃. The probable relationship between the diffusion coefficients of the In₆WO₁₂ components was obtained. A relation was developed for the process rate. The diffusion coefficients for the limiting component were calculated using the data on the estimated thickness of the product layers.     

Four-component system LiF-K<Subscript>2</Subscript>WO<Subscript>4</Subscript>-CaF<Subscript>2</Subscript>-BaWO<Subscript>4</Subscript>

The four-component system LiF-K₂WO₄-CaF₂-BaWO₄ has been studied for the first time using physicochemical methods. The a priori prediction of the phase complex revealed the phase tree and crystallization path of the system. The prediction was verified experimentally, by construction of a topologic model of the phase diagram, and the solution of the equations of the general law of liquidus-surface formation. The density has been measured, and the heat-storage properties of eutectic mixtures have been estimated.     

Fabrication and the electrochemical activation of network-like MnO<Subscript>2</Subscript> nanoflakes as a flexible and large-area supercapacitor electrode

Porous network-like MnO₂ thick films are successfully synthesized on a flexible stainless steel (SS) mesh using a simple and low-cost electrodeposition method followed by an electrochemical activation process. Morphology, chemical composition, and crystal structure of the prepared electrodes before and after the activation process are determined and compared by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) analyses. The results show that the implementation of the electrochemical activation process does not change the chemical composition and crystal structure of the films, but it influences the surface morphology of the MnO₂ thick layer to a flaky nanostructure. Based on the electrochemical data analysis, the maximum specific capacitance of 1400 mF (381 F g^?1) and 3700 mF (352 F g^?1) are measured for small (2.6 cm²) and large (10 cm²) surface area electrodes, respectively. In addition, a flexible symmetric MnO₂//MnO₂ solid-state supercapacitor shows a capacitance of 0.3 F with about 98% retention at different bending angles from 0 to 360°.     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Electrochemical characterization of MWCNT/Ni(OH)<Subscript>2</Subscript> composites as cathode materials

The hydrothermal method was used to synthesize multi-walled carbon nanotube/nickel hydroxide composites (MWCNT/Ni(OH)₂). The structure and morphology of the prepared materials were characterized by X-ray diffraction and transmission electron microscopy. The electrochemical performance of cathodes prepared with multi-walled carbon nanotubes (MWCNT) loaded into the β-nickel hydroxide materials was investigated employing cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopic measurements. It is shown that the cathode active material utilization increases for MWCNT/Ni(OH)₂ obtained after 24 h of hydrothermal synthesis. These composites exhibit a fairly good electrochemical performance as cathode materials. Based on the results, this fact could be associated with the formation of a continuous conductive network structure in the hydroxide matrix. The analyses of impedance data, according to a physicochemical model, allow the improvement of a better understanding of the main structural and physicochemical parameters that control the electrochemical performance of these systems.     

Facile synthesis of Fe@Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanowires as O<Subscript>2</Subscript> electrode for high-energy Li-O<Subscript>2</Subscript> batteries

Fe@Fe₂O₃ core-shell nanowires were synthesized via the reduction of Fe³⁺ ions by sodium borohydride in an aqueous solution with a subsequent heat treatment to form Fe₂O₃ shell and employed as a cathode catalyst for non aqueous Li-air batteries. The synthesized core-shell nanowires with an average diameter of 50–100 nm manifest superior catalytic activity for oxygen evolution reaction (OER) in Li-O₂ batteries with the charge voltage plateau reduced to ～3.8 V. An outstanding performance of cycling stability was also achieved with a cutoff specific capacity of 1000 milliampere hour per gram over 40 cycles at a current density of 100 mA g^?1. The excellent electrochemical properties of Fe@Fe₂O₃ as an O₂ electrode are ascribed to the high surface area of the nanowires’ structure and high electron conductivity. This study indicates that the resulting iron-containing nanostructures are promising catalyst in Li-O₂ batteries.     

Preparation and optical characterization of catalyst free SiO<Subscript>2</Subscript> sonogel hybrid materials

The synthesis of sol-gel materials induced by ultrasonic irradiation (sonolysis) is implemented as an alternative method for the fabrication of highly pure organic-inorganic composites with good monolithic, mechanical and optical properties. Ultrasonic irradiation, instead of commonly used basic- or acidic-catalyst was used to produce acoustical cavitation within the liquid H₂O/tetraethyl-ortosilicate (TEOS) reactants. This procedure forms a hydrolyzed-TEOS colloidal dispersion (sol) which produces, after drying, a highly pure SiO₂ network. The resulting SiO₂ glass exhibits high porosity and allows the inclusion of several organic compounds in the colloidal sol-state. Novel, optical active synthesized liquid crystalline (LC)-azo-compounds, bent shaped mesogens, cis- and trans-poly(1-ethynylpyrene)s, as well as fullerene (C₆₀) spheres and classical organic dyes were successfully incorporated as dopant agents within the novel catalyst free (CF) SiO₂-sonogel host matrix. Absorption and fluorescence spectroscopy studies were carried out in order to characterize the optical performance of both the CF-sonogel and several hybrid composites The pulsed laser photoacoustic technique (LPAT) was implemented to determine thermodynamic phase transitions of LC-based hybrids and laser induced damage (photo-degradation) in dye-based composites. Finally, comparative morphology studies between undoped reference samples and some doped composites were performed by Atomic Force Microscopy (AFM), where an optimal TEOS/dopant concentration ratio, to obtain good mechanical properties among the studied samples, has been found.     

Chemical composition optimization and characterization of the NiO/B<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system as a catalyst for ethylene oligomerization

The samples of the NiO/B₂O₃-Al₂O₃ system with NiO contents from 0.48 to 38.30 wt % were synthesized by the impregnation of borate-containing alumina (20 wt % B₂O₃). It was found that nickel oxide occurred in an X-ray amorphous state in the samples containing to 23.20 wt % NiO. At a NiO content of 4.86 wt % or higher, the support was blocked by the modifier to cause a decrease in the specific surface area from 234 to 176 m²/g and in the amount of acid sites from 409–424 to 333 μmol/g. An extremal character of the dependence of catalyst activity in ethylene oligomerization on NiO content was found with a maximum in the range of 4.86–9.31 wt %. Based on spectroscopic data, it was found that ethylene activation on the NiO/B₂O₃-Al₂O₃ catalyst can be associated with the presence of Ni²⁺ cations, which chemically interact with the support. The catalyst containing 4.86 wt % NiO at 200°C, a pressure of 4 MPa, and an ethylene supply rate of 1.1 h⁻¹ provided almost complete ethylene conversion at the yield of liquid oligomerization products to 90.0 wt %; the total concentration of C⁸⁺ alkenes in these products was 89.0 wt %.