用等离子体辅助分子束外延生长氧化锌单晶薄膜

利用等离子体辅助分子束外延(P-MBE)方法,通过优化生长条件,在c平面蓝宝石(Al_2O_3)上生长出氧化锌(ZnO)单晶薄膜。使用反射式高能衍射仪(RHEED)原位监测到样品表面十分平整,X射线摇摆曲线(XRC)测得ZnO薄膜的<002>取向半峰全宽为0.20°,证实为ZnO单晶薄膜。室温下吸收谱(ABS)和光致发光(PL)谱显示了较强的激子吸收和发射,且无深能级(DL)发光。电学性能测量表明,生长的ZnO为n型半导体,室温下载流于浓度为7×10~(16) cm~(-3),与体单晶ZnO中的载流子浓度相当。     

低温缓冲层对氧化锌薄膜质量的影响

利用金属有机化学气相沉积(MOCVD)法,在Si衬底上外延生长ZnO薄膜。为了改善氧化锌薄膜的质量,首先在Si衬底上生长低温ZnO缓冲层,然后再生长高质量的ZnO薄膜。通过XRD、SEM、光致发光(PL)光谱的实验研究,发现低温ZnO缓冲层可有效降低ZnO薄膜和Si衬底之间的晶格失配以及因热膨胀系数不同引起的晶格畸变。利用低温缓冲层生长的ZnO薄膜的(002)面衍射峰的强度要比直接在Si上生长的ZnO薄膜样品的高,并且衍射峰的半高宽也由0.21°减小到0.18°,同时有低温缓冲层的样品室温下的光致发光峰也有了明显的增高。这说明利用低温缓冲层生长的ZnO薄膜的结晶质量和光学性质都得到了明显改善。     

以Au为缓冲层在Si衬底上生长ZnO薄膜

采用化学气相沉积(CVD)方法在Si(001)衬底上分别制备了有金属Au缓冲层以及无Au缓冲层的ZnO薄膜。其中Au缓冲层在物理气相沉积(PVD)设备中蒸发,厚度大约为300nm。有Au缓冲层的ZnO薄膜晶体质量比直接在Si衬底上生长有了显著提高。利用X射线衍射(XRD)研究了所生长ZnO薄膜的结晶质量,有Au缓冲层的ZnO薄膜虽然仍为多晶,但显示出明显的择优取向。用光学显微镜研究了ZnO薄膜的表面特征,金属Au缓冲层显著地提高了在Si衬底上生长的ZnO薄膜的晶粒尺寸及平整度。同时利用室温光致发光(PL)谱研究了ZnO薄膜的光学性质,并分析了有Au缓冲层的ZnO薄膜NEB发光峰强度反而弱的可能原因。     

MgxZn1-xO薄膜的光致发光性能研究

用溶胶-凝胶旋涂的方法在Si(100)衬底上成功制备了MgxZn1-xO薄膜.通过对样品的X射线衍射花样进行分析,发现制得的样品都有明显的C轴取向.掺入Mg后C轴参数逐渐变小,这表明Mg离子进入了ZnO晶格.随着镁的掺入,其光致发光谱中的紫外发射峰的峰位发生明显蓝移,从3.28eV线性地变化到3.45eV.值得注意的是,掺入镁离子后,薄膜的紫外发光和可见发光的强度都显著高于ZnO.     

m面蓝宝石上ZnO/ZnMgO多量子阱的制备及发光特性研究

利用等离子体辅助分子束外延设备(P-MBE)在m面的蓝宝石(m-Al₂O₃)衬底上制备了ZnO/Zn_0.85Mg_0.15O多量子阱.反射式高能电子衍射谱(RHEED)图样的原位观察表明,多量子阱结构是以二维模式生长的.从光致发光谱中可以看到ZnO/Zn_0.85Mg_0.15O多量子阱在室温仍具有明显的量子限域效应.在290 K时阱宽为3 nm的ZnO/Zn_{0.85关键词： 等离子体辅助分子束外延 ZnO多量子阱 光致发光}     

富锌条件下生长氮掺杂氧化锌薄膜的光学和电学性质

报道了采用等离子体辅助分子束外延方法(P-MBE),利用NO作为N源和O源,在c-面蓝宝石(c-Al₂O₃)衬底上外延生长了N掺杂ZnO薄膜。X射线衍射谱(XRD)和吸收谱中都出现了不同于未掺杂样品的特性,X射线光电子谱(XPS)中也发现了N的受主信号。但是在霍尔效应(Hall-effect)测量中,发现该样品并没有出现预期的p型导电特性,而是出现载流子浓度很高(2.15×10²⁰cm^-3)的n型导电特性。结合XPS结果和理论分析,认为在富Zn条件下生长会导致过量的填隙Zn原子,补偿了全部的受主后,又促使其出现了从半导体-金属的Mott转变。     

衬底温度对ZnO薄膜的结构和光学特性的影响

利用等离子体辅助分子束外延(P-MBE)设备在蓝宝石衬底上通过改变生长温度,制备了不同的ZnO样品.研究了衬底温度对ZnO的结构、光学和电学性质的影响.样品的晶体结构利用X射线衍射谱进行表征.X射线衍射谱表明,所有的ZnO样品都是(002)取向的六角纤锌矿结构.随着生长温度的升高,X射线的(002)衍射峰的半峰全宽逐渐...     

MBE生长ZnO薄膜的结构和光学特性的研究

用等离子体源辅助分子束外延(P-MBE)方法在蓝宝石(0001)面上生长出了高质量的ZnO薄膜,并对其结构和发光特性进行了研究。在XRD中只观察到ZnO薄膜的(0002)衍射峰,其半高宽(FWHM)值为0.18°;而在共振Raman散射光谱中观测到1LO(579 cm-1 )和2LO(1 152 cm-1 )两个峰位,这些结果表明ZnO薄膜具有单一c轴取向和高质量的纤维锌矿晶体结构。在吸收光谱中观测到自由激子吸收和激子-LO声子吸收峰,这表明在ZnO薄膜中激子稳定的存在于室温,并且两峰之间能量间隔为71.2 meV,与文献上报道的ZnO纵向光学声子能量(71 meV)相符。室温下在光致发光光谱(PL)中仅观测到位于376 nm处的自由激子发光峰,而没有观测到与缺陷相关的深能级发射峰,表明ZnO薄膜具有较高的质量和低的缺陷密度。     

LP-MOCVD异质外延ZnO薄膜中的应力及对缺陷的影响

利用低压金属有机化学气相淀积(LP-MOCVD)在Si基片上外延生长ZnO薄膜，制备了两类样品 ：一类是在Si上直接外延ZnO，另一类是在Si上通过SiC过渡层来外延ZnO.根据两类样品的拉 曼光谱、x射线衍射、原子力显微图和光致发光的结果，表明ZnO外延薄膜中的张应力对薄膜 的结晶状况有着重要的影响，使用SiC过渡层能够有效缓解ZnO薄膜中的张应力，减小缺陷浓 度，提高ZnO外延层的质量；然后根据缺陷的形成机制进一步提出，对于ZnO/Si，其中较大 的张应力导致了高浓度的非辐射复合缺陷的形成，使得样品的紫外和绿峰的发射强度均大大 降低；对于ZnO/SiC/Si，其中较小的张应力导致ZnO薄膜中主要形成氧替位缺陷O_{Zn，从而使发光中的绿峰增强. 关键词： ZnO薄膜 应力 缺陷 拉曼光谱}     

气相输运法制备ZnO薄膜(英文)

运用气相输运技术在不同的衬底上制备ZnO薄膜,同时对这些ZnO薄膜的表面形貌、晶体结构和光学特性进行表征。在扫描电子显微镜图像上可以看到,相比没有镀金的Si衬底,ZnO纳米颗粒在镀金的Si衬底上的生长尺寸较大。X射线衍射测试结果表明,在Si(111)和Si(100)衬底上生长的ZnO薄膜显示出不同的六角纤锌矿结构的衍射峰,但没有出现立方闪锌矿ZnO结构的衍射峰。在镀金的Si衬底上,ZnO薄膜生长取向主要为c轴方向。此外,所有ZnO样品的光致发光谱上均只出现一个狭窄且强的紫外峰,约在389 nm(3.19 eV)波长处。     

Speckle characteristics of a broad-area VCSEL in the incoherent emission regime

We present a technique to reduce the speckle contrast of a NIR broad-area VCSEL based on the spatially incoherent emission regime that can be obtained when using the proper driving conditions. We evaluate the efficiency of this technique to reduce the speckle contrast by comparing it with the speckle characteristics in multimode emission under cw operation. Depending on the illumination setup, the incoherent emission regime can lead to a strongly reduced speckle contrast down to 1.3%. This is in agreement with estimates of the expected speckle contrast reduction when three contrast reducing effects are taken into account. These low contrast values make the investigated sources attractive for several applications that suffer from speckle noise.     

Structural characterization of ultrathin Cr and Sc films for soft X-ray mirrors

The structure of multilayers of ultrathin scandium (Sc) and chromium (Cr) films has been characterized by means of transmission electron microscopy (TEM). Face centered cubic Sc was found both in magnetron sputtered thin Sc layers on Si(0 0 1) and in Cr/Sc multilayers for soft X-ray mirrors. The single Sc and Cr layers are polycrystalline with randomly oriented grains, while Sc and Cr within the Cr/Sc multilayer show a strong [0 0 1] texture in the deposition direction. From high-resolution images the orientation-relationship at the Cr/Sc interfaces could be deduced as: Sc_[110]//Cr_[100] and Sc_[010]//Cr_[110], which was confirmed by image simulations.     

Optical transmission through an interface between subwavelength slits

This paper studies optical transmission through an interface between two slits with different widths in a sheet composed of an ideal conductor. Such a structure is of potential use in fabricating optical diode and may be the simplest one compared to other designs. Our calculations show that there is a critical wavelength. When the light wavelength is below the critical wavelength, the transmissivity is unidirectional. The expression of the stable transmissivity as a function of the ratio of the widths of the two slits was obtained analytically. Particularly, at the critical wavelength, the transmissivities are zero. This phenomenon has great potential for application in the manufacture of wavelength blockers.     

Effect of Ir(pq)2acac doping on CBP in phosphorescence organic light-emitting diodes

Doping is one of the most powerful methods amongst the various performance improvement ways. Doping affects the energy levels of the host layer by the energy level of the dopant. This allows the energy bandgap to be adjusted to a desired level and thus generates light corresponding to that energy level. Alternatively, it can act as an energy barrier between the interfaces to change the flow of carriers. In this study, the voltage dependences of undoped and doped devices were observed. Bis(2-phenylquinoline) iridium(III) (acetylacetonate) (Ir(pq)₂acac) was doped in 4,4′-N, N′-dicarbazole-biphenyl (CBP) as the emission layer. The light intensity changes with the doping concentration, and the efficiency was also studied. When a high voltage was applied, the effect of triplet-triplet annihilation (TTA) adversely affected the electron-hole recombination. We analyzed the optimal operating conditions and the effect of doping concentration on OLEDs.     

Grain boundary potential and charge density at grain boundaries of chemically prepared thin silver sulfide films

The grain boundary potential and interface state charge density at the grain boundaries of silver sulfide (Ag₂S) thin films prepared by chemical conversion of cadmium sulfide (CdS) films have been determined from the dc resistance of the material and are found to be sensitive to annealing. A reduction in the grain boundary potential and the grain boundary charge density of the film has been noticed when the source CdS film is annealed at different temperatures prior to chemical conversion. The variation in the grain boundary charge density of the grown Ag₂S film with source annealing temperature has been found to be similar to that of thin cadmium sulfide film, reported earlier. An additional low temperature heat treatment of the sample results in an enhancement in the charge density at the grain boundaries. The change in the silver vacancy and/or oxygen and sulfur content of the films as revealed from the energy dispersive spectra of the films suggests possible role of film composition on the grain boundary charge density.     

三螺旋DNA分子Poly(dT)·Poly(dA)·Poly(dT)碱基振动模式

利用晶格动力学方法计算了三螺旋 DNA分子 poly(d T)· poly(d A)· poly(d T)碱基振动模式 ,并根据势能分布矩阵对碱基振动模式进行了指定。计算的模式频率同拉曼光谱实验相符合     

Belle实验观测到新类粲偶素结构

利用在Υ(nS)(n=1,2,4,5)共振态及其附近采集的大量数据,Belle实验测量了末态中含两个矢量粒子的双光子过程γγ→J/ψ和ωJ/ψ.在这两个过程中,发现了两个窄共振结构X(4350)和X(3915).这两个新结构的性质目前尚不清楚,可能是普通粲偶素粒子,也可能是含一对粲夸克和一对轻夸克的四夸克态,或含一对粲夸克和一个激发胶子的混杂态,或是由其他未知的动力学原因造成的奇特结构.Belle同时发现在γγ→J/ψ过程中,不存在显著的Y(4140)的信号,实验结果与将Y(4140)解释为四夸克态的部分理论预期有较大差异.     

XYZ particles at Belle

In this paper, I review recent progress in the study of the XYZ particles at Belle. I only focus on studies with charmonium and one or more light mesons in the final states. This covers the X(3872), X(3915),Y(4140), X(4350), and the charged Z states.     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

The effect of phonon anisotropic scattering on the thermal conductivity of silicon thin films at 300K and 400K

Previous studies have shown that anisotropy in phonon transport exist because of the difference in phonon dispersion relation due to different lattice directions, as observed by a difference in in-plane and cross-plane thermal conductivities. Our current work intends to study the effect of anisotropy scattering on silicon thermal conductivity at 300 K and 400 K. We adopt the Henyey and Greenstein probability density function in our phonon Monte Carlo simulation to investigate the effect of highly forward and backward scattering events. The impact of applying the anisotropy scattering using this approach is discussed in detail. While the forward and backward scattering will increase and decrease thermal conductivity respectively, the extent of the effect is non-linear such that forward scattering has a more obvious effect on thermal conductivity than backward scattering.