Preconcentration and voltammetric determination of palladium (II) at sodium humate modified carbon paste electrodes

A chemically modified carbon paste electrode was prepared by incorporating appropriate amounts of sodium humate(NaA). Palladium(II) was selectively accumulated in a solution of Britton-Robinson(B-R) buffer (pH 2.8) onto the electrode surface in open circuit mode. The subsequent electrochemical measurement was carried out by cyclic voltammetry (CV) and linear sweep anodic stripping voltammetry (LSASV) in a supporting electrolyte of 1.0 M HCl. The obtained oxidation currents (I_pa1 and L_pa2) were proportional to the Pd(II) concentration in the range of 4.7 × 10^–6 - 9.4 × 10^–8 M. The developed method was applied to the quantitative determination of palladium in real samples.     

Voltammetric behavior and determination of bismuth on sodium humate modified carbon paste electrode

The preconcentration and voltammetric behavior of Bi^III on a sodium humate modified carbon paste electrode was studied by means of cyclic voltammetry (CV) and differential pulse stripping voltammetry (DPSV). The proposed measurement involves an initial nonelectrolytic preconcentration step in which Bi^III is complexed by the surface modifier in a solution of 0.05 M KNO₃-0.0106 M HNO₃ (pH 2.0) and a subsequent electrochemical scan step in which the preconcentrated Bi^III was reduced and then oxidized promptly in supporting electrolyte of 0.5 M HNO₃. The resulting DPSV anodic current was proportional to the concentration of Bi^III ion over the range of 4.78 × 10⁻⁸–1.44 × 10⁻⁵ M. The detection limit was 4.78 × 10⁻⁸ M. The proposed method was used to determine bismuth in various samples. Various factors affecting the electrode behavior were also investigated at the same time.     

Stripping voltammetric determination of mercury(II) at antimony-coated carbon paste electrode

A new procedure was elaborated to determine mercury(II) using an anodic stripping square-wave voltammetry at the antimony film carbon paste electrode (SbF-CPE). In highly acidic medium of 1 M hydrochloric acid, voltammetric measurements can be realized in a wide potential window. Presence of cadmium(II) allows to separate peaks of Hg(II) and Sb(III) and apparently catalyses reoxidation of electrolytically accumulated mercury, thus allowing its determination at ppb levels. Calibration dependence was linear up to 100 ppb Hg with a detection limit of 1.3 ppb. Applicability of the method was tested on the real river water sample.     

Preconcentration and determination of bentazepam at C18-modified carbon paste electrodes

Summary A method for the determination of bentazepam by the oxidation wave which originates from the 1 N, using a 50% C18 carbon paste electrode is described. A preconcentration cell at open circuit and a measuring cell have been used. The electroanalytical technique employed was the differential pulse voltammetry. The interferences with different psychotropic drugs have been applied to the determination of bentazepam directly in urine and with previous extraction in ethyl ether.     

Electrode reactions of palladium(II) in chloride solution at carbon paste electrodes modified with derivatives of N-benzoylthiourea

The study of the electrode reactions of palladium(II) at non-modified carbon paste electrodes (CPEs) in chloride solution has revealed the existence of a chloropalladate(II) complex at the electrode surface. The complex is formed during the application of anodic potentials after preceding palladium deposition. In the present paper the electrode reactions of Pd^II at CPEs modified with some N′,N′-disubstituted derivatives of N-benzoylthiourea [as selective ligands for palladium(II)] are studied in chloride solution by cyclic voltammetry. Two reduction peaks are observed in the cathodic scans recorded after deposition of palladium and anodization of the electrode. From the results it is concluded that [in addition to the chloropalladate(II) complex, observed at the non-modified electrode] a second palladium complex is formed at positive potentials. The formation of the palladium(II) complex of the N-benzoylthiourea derivatives by ligand exchange at the electrode surface is assumed. The ligand exchange itself occurs without charge transfer across the electrode|solution interface; therefore, it cannot be detected electrochemically. After palladium deposition and anodic treatment a pronounced "inverse" peak (i.e., an anodic peak in the cathodic scan) with peak currents up to 100 μA is observed at about +0.8 V. Its peak current increases with the amount of deposited palladium and the number of cycles. The reactions at the electrode surface are discussed. The results of the study reveal the existence of two different surface complexes of palladium(II) at ligand-modified CPEs, but the surface reactions could not be elucidated in detail. Electronic Publication     

Sensitive voltammetric determination of rutin at an ionic liquid modified carbon paste electrode

An ionic liquid modified carbon paste electrode (IL/CPE) had been fabricated by using hydrophilic ionic liquid 1-amyl-3-methylimidazolium bromide ([AMIM]Br) as a modifier. The IL/CPE was characterized by scanning electron microscope and voltammetry. Electrochemical behavior of rutin at the IL/CPE had been investigated in pH 3.29 Britton-Robinson (B-R) buffer solution by cyclic voltammetry (CV) and square wave voltammetry (SWV). The experimental results suggested that the modified electrode exhibited an electrocatalytic activity toward the redox of rutin. The electron transfer coefficient (α) and the standard rate constant (k_s) of rutin at the modified electrode were calculated. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 4.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol L⁻¹ (r = 0.9998), with a detection limit of 1.0 × 10⁻⁸ mol L⁻¹ (S/N = 3). The relative standard deviation (R.S.D.) for six times successful determination of 8.0 × 10⁻⁷ mol L⁻¹ rutin was 1.2%. The proposed method was applied to determine rutin in tablet and urine sample. In addition, the IL/CPE exhibited a distinct advantage of simple preparation, surface renewal, good reproducibility and good stability.     

Stripping voltammetric determination of silymarin in formulations and human blood utilizing bare and modified carbon paste electrodes

Silymarin is one of the most powerful natural substances that have the ability to protect and rebuild the liver cells damaged by alcohol and other toxic substances. Silymarin showed two irreversible anodic peaks in buffered solutions (pH 2.5-8.0) at either the bare carbon paste electrode or the montmorillonite-Ca modified carbon paste one. These two peaks have been attributed to oxidation of the two phenolic OH groups at positions C-20 and C-7 of silymarin molecule. A square-wave adsorptive anodic stripping voltammetry method was optimized for determination of silymarin utilizing the bare and the modified carbon paste electrodes. The method was fully validated and successfully applied for the determination of silymarin in commercial formulations and human serum without prior extraction utilizing both carbon paste electrodes. Limits of quantitation of 1 × 10⁻⁷ and 7 × 10⁻⁹ mol L⁻¹ silymarin have been achieved in bulk form or in formulations while 2 × 10⁻⁷ and 8 × 10⁻⁹ mol L⁻¹ silymarin were achieved in spiked human serum utilizing the bare carbon paste electrode and the modified one, respectively. The two electrodes exhibited excellent selectivity towards silymarin even in the presence of 10²to 10³-fold excess of its co-formulated drugs, common excipients, and common metal ions. The pharmacokinetic parameters of silymarin in plasma of healthy human volunteers were estimated following the administration of a single oral dose of 120 mg silymarin utilizing the modified carbon paste electrode. The estimated pharmacokinetic parameters were favorably compared with those reported in literature.     

Preconcentration and voltammetric determination of the herbicide metamitron with a silica-modified carbon paste electrode

A carbon paste electrode incorporating silica (Si-MCPE) was fabricated to accumulate Metamitron at the electrode surface. Several electroanalytical techniques were used to explore its reductive behaviour. The results indicate that the system is irreversible and fundamentally controlled by adsorption. The adsorptive stripping response has been evaluated with respect to accumulation time, deposition potential, scan rate, pH and other variables, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. In both cases a voltammetric peak is obtained, at –0.542 V (DPV) and –0.421 V (SWV) in Britton-Robinson buffer (pH 1.9). The detection limits were 3.66 × 10^–1 M and 4.22 × 10^–9 M for AdS-DPV and AdS-SWV, respectively. Under optimum conditions the Metamitron reduction peak gave two linear regions in the range from 4.0 × 10^–9 M to 8.0 × 10^–8 M by means of AdS-DPV, with a coefficient of variation of 2.19% (n = 10) for 1 × 10^–8 M herbicide solution. A method was developed for determination of Metamitron in soils, with a recovery of 98.8% and a coefficient of variation of 5.26% (0.01 g/g of soil).     

Copper(II) modified carbon paste electrodes based on self-assembled mercapto compounds-gold-nanoparticle

Three mercapto compounds [2-mercapto-5-(1-methyl-5-nitroimidazole-2-yl)-1,3,4-thiadiazole] (MMNIT), [2-mercapto-5-(5-nitrofuran-2-yl)-1,3,4-thiadiazole] (MNFT) and [2-mercapto-5-(5-nitrothiophen-2-yl)-1,3,4-thidiazole] (MNTT) were used for self-assembled-gold nanoparticle (SAGNP) modified carbon paste electrodes. The electrodes were applied as indicator electrodes for potentiometric determination of Cu(II) ion. The prepared electrodes exhibit a Nernstian slope of 31.0+/-0.5 mV per decade for Cu(II) ion over a wide concentration range of 7.9x10(-9)-3.2x10(-2), 7.9x10(-9)-7.9x10(-4), and 2.8x10(-8)-7.9x10(-3) mol L(-1) for MMNIT, MNFT and, MNTT, respectively. The detection limits of electrodes were 3.5 (+/-0.2)x10(-9), 4.1x10(-9), and 4.1x10(-8) mol L(-1) of copper ion, respectively. The potentiometric responses of electrodes based on MMNIT, MNFT, and MNTT are independent of the pH of test solution in the pH range 2.0-5.5, 2.5-7.0, and 2.0-6.5, respectively. They have quick response with response time of about 5 s. The proposed electrodes show fairly good selectivity over some alkali, alkaline earth, transition and heavy metal ions. Finally, the proposed electrodes were successfully employed to detect Cu(II) ion in hair and water samples.     

Chemical accumulation and voltammetric determination of traces of nickel(II) at glassy carbon electrodes modified with dimethyl glyoxime containing polymer coatings

The objective of the present study was to develop a solid mercury free electrode for the voltammetric determination of traces of nickel(II) in solution. For this purpose chemically modified electrodes (CME's) were constructed from glassy carbon coated with dimethylglyoxime-containing polymers. CME's based on a composite matrix, which contained polyvinyl chloride, polyaniline, and dimethylglyoxime were shown to possess the ability to accumulate traces of nickel(II) from ammonia buffered aquatic solutions by a purely chemical attachment. Moreover the nickel(II) contents of such solutions could be determined using voltammetric quantitation of the nickel(II) dimethylglyoximate deposits on the CME surfaces and the standard addition technique. The CME surfaces could subsequently be regenerated by acid treatment. The limit of detection for Ni(II) following a 240 s chemical deposition was estimated as 18 mug Ni l(-1), and the CME results for traces of Ni(II) in fresh water compared well with the results obtained by atomic absorption spectroscopy. Moreover the CME's retained their sensitivity for more than two days, i.e. significantly longer than the 3 h, during which analogous carbon paste electrodes completely lost their affinity to nickel(II).     

Anodic stripping voltammetric determination of silver ion at a carbon paste electrode modified with carbon nanotubes

A carbon paste electrode (CPE) was modified with multi-wall carbon nanotubes and successfully applied to the determination of silver ion by differential pulse anodic stripping voltammetry. Compared to a conventional CPE, a remarkably improved peak current response and sensitivity is observed. The analytical procedure consisted of an open circuit accumulation step for 2?min in ?0.4?V, this followed by an anodic potential scan between +0.2 and?+?0.6?V to obtain the voltammetric peak. The oxidation peak current is proportional to the concentration of silver ion in the range from 1.0?×?10^?8 to 1.0?×?10^?5?mol?L^?1, with a detection limit of 1.8?×?10^?9?mol?L^?1 after an accumulation time of 120?s. The relative standard deviation for 7 successive determinations of Ag(I) at 0.1???M concentration is 1.99%. The procedure was validated by determining Ag(I) in natural waters.

A new method for the voltammetric determination of molybdenum(VI) using carbon paste electrodes modified in situ with cetyltrimethylammonium bromide

Molybdenum(VI) is determined by anodic stripping voltammetry using a carbon paste electrode modified in situ with cetyltrimethylammonium bromide (CTAB). The preconcentration of molybdenum is performed by adsorption and reduction of ion-pairs of cetyltrimethylammonium and molybdenum(VI) oxalate at a potential of −0.4 V vs. the saturated calomel electrode (SCE). The supporting electrolyte contains 0.01 M oxalic acid and 0.075 mM CTAB. Differential pulse anodic stripping voltammetry exploiting the reoxidation signal is used for the determination of trace levels of molybdenum(VI). Linearity between current and concentration exists for a range of 0.5–500 μg 1⁻¹ Mo with proper preconcentration times; the limit of detection (calculated as 3σ) is 0.04 μg 1⁻¹ with an accumulation period of 10 min.     

Catalytic adsorptive stripping voltammetric determination of copper(II) on a carbon paste electrode

A catalytic adsorptive stripping voltammetric method for the determination of copper(II) on a carbon paste electrode (PCE) in an alizarin red S (ARS)-K₂S₂O₈ system is proposed. In this method, copper(II) is effectively enriched by both the formation and adsorption of a copper(II)-ARS complex on the PCE, and is determined by catalytic stripping voltammetry. The catalytic enhancement of the cathodic stripping current of the Cu(II) in the complex results from a redox cycle consisting of electrochemical reduction of Cu(II) ion in the complex and subsequent chemical oxidation of the Cu(II) reduction product by persulfate, which reduces the contamination of the working electrode from Cu deposition and also improves analytical sensitivity. In Britton-Robinson buffer (pH 4.56±0.1) containing 3.6×10⁻⁵ mol L⁻¹ ARS and 1.6×10⁻³ mol L⁻¹ K₂S₂O₈, with 180 s of accumulation at −0.2 V, the second-order derivative peak current of the catalytic stripping wave was proportional to the copper(II) concentration in the range of 8.0×10⁻¹⁰ to ∼3.0×10⁻⁸ mol L⁻¹. The detection limit was 1.6×10⁻¹⁰ mol L⁻¹. The proposed method was evaluated by analyzing copper in water and soil.     

A carbon paste electrode modified with a cobalt(II) coordination polymer for the direct voltammetric determination of tryptophan

We have synthesized a cobalt(II) coordination polymer and have characterized it by various methods including X-ray single crystal structural analysis. The polymer was used as modifier to fabricate a carbon paste electrode that displays electrochemical activity towards tryptophan (Trp). Trp is oxidized at the surface of the electrode in buffer solution of pH 4.2, yielding a single peak at 814 mV. The experimental conditions such as the concentration, the composition and the pH values of the supporting electrolyte, accumulation time, and the scan rate were optimized. Under the optimized conditions, the current of peak is linearly related to the concentration of Trp in the range from 0.2 to 8.0 μM, and from 8.0 to 80.0 μM. The detection limit (at S/N?=?3) is 0.1 μM at an accumulation time of 60 s. The determination of Trp in amino acid injection solutions was evaluated and the results were satisfactory. The recoveries were in the range of 97.5% to 103.0%.

Stripping voltammetric determination of platinum metals at a carbon paste electrode modified with cationic surfactants

In this contribution, a novel method is described for the determination of platinum metals. The procedure developed employs a carbon paste electrode modified in situ with cationic surfactants of the quaternary ammonium salt type. The pre-concentration step is based on a specific accumulation mechanism involving ion-pair formation; the detection being performed by cathodic scanning in the differential pulse voltammetric mode. Regarding the individual forms of platinum metals, the method has been found convenient for the determination of three heavy platinum metals in the form of Pt(IV), Ir(III) and Os(IV), whereas for the remaining elements (Ru, Rh, and Pd) was almost inapplicable. Platinum metals of the former group can be pre-concentrated in chloride-containing supporting media via PtCl₆²⁻, IrCl₆³⁻ and OsCl₆²⁻ complex anions, the central atom of each species being fairly reducible during the voltammetric scan. Stripping signals for both platinum and iridium were proportional to the concentration in a range of 1-10 × 10⁻⁶ M Pt(IV) and Ir(III); the response for osmium being linear within 0.1-6 × 10⁻⁷ M Os(IV) with a detection limit of about 5 × 10⁻⁹ mol l⁻¹. During optimisation, special attention was paid to the accumulation mechanism, choice of key experimental conditions, and to interference effects from foreign ions with potentially ion-pairing capabilities (AuCl₄⁻, TlCl₄⁻, CrO₄²⁻, MnO₄⁻, SCN⁻, and I⁻). The method elaborated has been tested on both model solutions and real samples of industrial waste water, showing in both cases satisfactory analytical performance.     

A selective voltammetric method for uric acid detection at Nafion(R)-coated carbon paste electrodes

A square-wave voltammetric method together with Nafion®-coated carbon paste electrodes were used for the selective determination of uric acid in the presence of a high concentration of ascorbic acid. Since the oxidation potential of uric acid is about 200 mV more positive than that of ascorbic acid at the Nafion®-coated carbon paste electrode, the selectivity can be greatly improved simply by applying an electrolysis potential of +0.4 V vs. Ag/AgCl where only ascorbic acid is oxidised. The acceptable tolerance of ascorbic acid concentration for the determination of uric acid is as high as 1.5 mM. With 30 s of electrolysis time, a linear calibration curve is obtained over the 0–50 μM range in 0.05 M citrate buffer solution, pH 4.0, with slope (μA/μM) and correlation coefficient of 0.34 and 0.9984, respectively. The detection limit (3σ) is 0.25 μM. The practical analytical utility is illustrated by selective measurements of uric acid in human urine without any preliminary treatment.     

依诺沙星在碳糊电极上的阳极吸附伏安法研究

在0.40 mol/L的NaAc-HAc(pH 4.5)缓冲液中,使用JP-303极谱分析仪,依诺沙星在碳糊电极(CPE)上有一灵敏的吸附伏安氧化峰,峰电位为1.17 V(vs.SCE).该氧化峰的二阶导数峰电流与依诺沙星的浓度在4.0×10-9～4.0×10-7 mol/L(富集90 s)范围内呈良好的线性关系,相关系数为0.995,检出限为2.0×10-9 mol/L(S/N=3,富集110 s).探讨了依诺沙星在碳糊电极上的伏安性质和电极反应机理,并且用于诺佳胶囊中依诺沙星的测定.     

Adsorptive stripping voltammetric determination of ketoconazole in pharmaceutical preparations and urine using carbon paste electrodes

The oxidation of ketoconazole on a bare carbon paste electrode was studied voltammetrically. The results indicated that the process is irreversible and controlled by an adsorption-extraction process which allows the accumulation of the drug at the electrode surface. After the optimization of solution pH, accumulation variables and instrumental parameters, sensitive differential pulse and linear sweep voltammetric peaks were obtained whose peak currents were linearly proportional to the ketoconazole concentration over the ranges 2.4 x 10(-8)-4.8 x 10(-7) and 9.1 x 10(-7)-1.0 x 10(-5) M, respectively. Based on these findings, a simple procedure was developed for the determination of ketoconazole in human urine and formulations.     

Electrochemical behaviour of drugs at lipid modified carbon paste electrodes

Mixing carbon paste with a charged lipid, in an appropriate ratio, permitted us to prepare a modified electrode whose surface exhibits interesting characteristics of the constituting lipid. Two negatively charged phospholipids have been selected, namely: asolectin and cardiolipin. By investigating the electrooxidation of several drugs which are known to interact strongly with the lipid component of cellular membranes (adriamycin, epirubicin and promethazine) it was possible to demonstrate markedly different behaviour at the lipid modified carbon paste electrode (LMPCE) depending on the pH of the solution. By analysing the results of linear scan, ac and adsorptive voltammetry and by taking into account literature data on drug-membrane interactions, it was possible to postulate a model of the LMCPE interface with thin layers of lipids covering the graphite particles. The differential capacity measurements as a function of time (fixed potential) and in the presence of increasing amounts of drugs enabled us to point out profound increases in the capacity of the LMCPE in the presence of adriamycin and epirubicin. In addition, the more negatively charged the lipids were, the higher was the capacity increase.