高效毛细管区带电泳法快速测定尿液中的肌酐

建立了一种快速测定尿中肌酐浓度的高效毛细管电泳方法。利用非涂层石英毛细管(64.5 cm×50μm i.d),以pH 2.5,0.1 mmol/L H3PO4作为电泳缓冲液,检测波长191 nm,用0.05 Pa压力进样4 s,在电压16 kV快速分离尿液中的肌酐,采用外标法定量。肌酐的迁移时间约为5.5 min,肌酐浓度在34.5~8840μmol/L范围内呈良好的线性(r2=0.999)。平均日内精密度为2.5%,日间精密度为3.0%。回收率94.1%~99.0%。与全自动生化分析仪碱性苦味酸速率法相比有良好的相关性(r=0.990,n=56)。高效毛细管电泳法测定尿肌酐可应用于临床样品的检测。     

Creatinine determination in urine samples by batchwise kinetic procedure and flow injection analysis using the Jaffé reaction: chemometric study

The classical Jaffé reaction for the determination of creatinine in urine samples is tested. A comparative study of the main analytical characteristics focussed to minimize the bias error and improve the precision, for the batchwise and flow injection (FI) methods is realized. Also, the effect of the albumin concentration in the determination of creatinine has been studied. Different analytical signals were studied. Absorbance increments at different times permit to estimate the creatinine concentration free from bias error in urine by the batchwise method using the calibration graph obtained with creatinine standards and no measurement of the blank solution is needed. The lineal interval was 0.92–50 mg l⁻¹ and seven samples can be processed per hour by an operator. No previous treatment of the urine sample is necessary. The FI method provides also good results. The lineal interval was 30–100 mg l⁻¹ and the sample rate was around 20 samples per hour. If increased albumin levels are detected in the urine, standard addition method or the calibration graphs with standards in presence of albumin are needed in order to obtain accurate results when FI method is employed. The obtained accuracy of the both methods allows its application as diagnostic tool to establish the urinary creatinine levels.     

Kinetic-enzymatic determination of oxalate in urine by flow-injection analysis with double stopped flow

An enzymatic stopped-flow injection method for the determination of oxalate is proposed. Two sequential haltings of the flow are made, the first while the sample plug is in a reactor packed with controlled-pore glass and immobilized oxalate decarboxylase, and the second on merging of the sample plug with a stream containing an auxiliary enzyme (formate dehydrogenase) as the plug reaches the flow cell, where absorbance-time data are collected. The linear range of the calibration graphs is between 0.1 and 3.0 mM oxalate and their sensitivity depends on the interval over which measurements are made. The proposed method was applied to the determination of oxalate in urine without separation of the analyte by precipitation, with excellent results.     

Chemiluminometric photo-induced determination of Strychnine in a Multicommutation flow assembly

This paper deals on the determination of Strychnine, a potent and dangerous pesticide and the analytical procedure is based on the photo-induced chemiluminescence of the pesticide by means of the Multicommutation continuous-flow methodology. Small segments of the pesticide solution were sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. The required time of UV irradiation was obtained by stopped-flow during 150 s; then, the resulting solution formed alternated segments with the oxidizing solution containing 5 × 10⁻³ mol l⁻¹ Ce(IV) in 0.6 mol l⁻¹ nitric acid. The calibration range, from 2 μg l⁻¹ to 50 mg l⁻¹, resulted in a linear behaviour over the range 25 μg l⁻¹ to 20 mg l⁻¹ and fitting the equation: I = 4706x + 624 with a correlation coefficient of 0.9955. The limit of detection was 2 μg l⁻¹ and the sample throughput 15 h⁻¹. After testing the influence of a large series of potential interferents, the method was applied to different kinds of samples.     

Spectrophotometric determination of catecholamines with metaperiodate by flow-injection analysis

A flow-injection Spectrophotometric method for the determination of adrenaline and isoprenaline, based on the reaction with metaperiodate, is described. The calibration graphs are linear up to 2 × 10⁻⁴ M. Flow injection allows the measurement of 120 samples per hour. The method was successfully applied to the determination of both catecholamines in pharmaceuticals.     

A clean method for flow injection spectrophotometric determination of cyclamate in table sweeteners

A flow system based on the multicommutation is proposed for fast and clean determination of cyclamate. The procedure exploits the reaction of cyclamate with nitrite in acidic medium and the spectrophotometric determination of the excess of nitrite by iodometry. The flow system was designed with a set of solenoid micro-pumps to minimize reagent consumption and waste generation. The detection limit was estimated as 30 μmol L⁻¹ (99.7% confidence level) with linear response ranging up to 3.0 mmol L⁻¹. The coefficient of variation was estimated as 1.7% for a solution containing 2.0 mmol L⁻¹ cyclamate (n = 20). About 60 samples can be analyzed per hour, consuming only 3 mg KI and 1.3 μg NaNO₂, and generating 2.0 mL of effluent per determination, thus providing an environmentally friendly alternative to previously proposed procedures. Common artificial and natural sweeteners did not interfere when present in concentrations 10-times higher than cyclamate. The procedure was successfully applied for determination of cyclamate in artificial table sweeteners with results in agreement with the reference method at the 95% confidence level.     

Spectrophotometric simultaneous determination of nitrite, nitrate and ammonium in soils by flow injection analysis

A new rapid flow injection procedure for the simultaneous determination of nitrate, nitrite and ammonium in single flow injection analysis system is proposed. The procedure combines on-line reduction of nitrate to nitrite and oxidation of ammonium to nitrite with spectrophotometric detection of nitrite by using the Griess-llosvay reaction. The formed azo dye was measured at 543 nm. The influence of reagent concentration and manifold parameters were studied. Nitrite, nitrate and ammonium can be determined within the range of 0.02–1.60 μg mL⁻¹, 0.02–1.60 μg mL⁻¹ and 0.05–1.40 μg mL⁻¹, respectively. R.S.D. values (n = 10) were 2.66; 1.41 and 3.58 for nitrate, nitrite and ammonium, respectively. This procedure allows the determination and speciation of inorganic nitrogen species in soils with a single injection in a simple way, and high sampling rate (18 h⁻¹). Detection limits of 0.013, 0.046 and 0.047 μg mL⁻¹were achieved for nitrate, nitrite and ammonium, respectively. In comparison with others methods, the proposed one is more simple, it uses as single chromogenic reagent less injection volume (250 mL in stead of 350 mL) and it has a higher sampling rate.     

Exploiting kinetic spectrophotometric determination of captopril, an angiotensin-converting enzyme inhibitor, in a multi-pumping flow system

The implementation of a differential kinetic spectrophotometric method for the determination of angiotensin-converting-enzyme inhibitors in pharmaceutical formulations is described. The determination method was based on the monitoring (350 nm) of the reaction between captopril and iodate, in the presence of iodide, versus time and was fully automated by exploiting the multi-pumping flow concept. The developed multi-pumping flow system included four discretely actuated solenoid micro-pumps as unique flow manifold active components. The automatic control of the solenoid micro-pumps, under time-based and pulse-counting routines, allowed the implementation of a reliable and versatile analytical determination, with the additional advantage of permitting a runtime access to important analytical parameters, such as flow rate, sample insertion and reagent addition synchronisation, facilitating this way the establishment of an approach for kinetic measurements, directly due to the efficient solution handling and accurate timing control.

A linear range of determination was verified for captopril concentrations between 10.0 and 60.0 μg mL⁻¹ with a sample throughput of about 100 determinations per hour. The results were in agreement with those obtained by the reference procedure with relative deviations between 1.81 and 4.48%.     

Spectrophotometric determination of total phenolics by solvent extraction and sorbent extraction optosensing using flow injection methodology

Flow injection analysis (FIA) procedures for the Spectrophotometric determination of phenol involving in-line concentration by solvent and sorbent extraction have been developed. The imine product formed in the reaction between phenol and 4-aminoantipyrine (4-AAP) is either extracted into chloroform (solvent extraction) or is temporarily retained on C₁₈-modified silica material contained in a microcolumn (sorbent extraction). In the latter case two variants of detection have been used namely the Spectrophotometric measurement of the methanolic eluent containing the concentrated dye and at-column optosensing of the retained reaction product followed by methanol elution to maintain reversibility of the process. In the solvent extraction procedure a 10-fold increase of sensitivity compared to the common FIA method without extraction is achieved but no corresponding improvement in detectability is observed. Under optimized conditions the detection limit amounts to 8 μg l⁻¹. Using sorbent extraction methodology, high concentration factors can be obtained when large sample volumes are used. The only limitation in getting correspondingly lower detection limits are an increasingly high and variable blank value with sampling volume. The detection limits obtained for measurement of the absorbance in the eluent and on-column optosensing are 11 μg l⁻¹ and 0.4 μg l⁻¹, respectively. A study of the extractability of various phenol derivates using both solvent and sorbent extraction revealed lower relative response rates compared to the FIA method without extraction. Phenolics that possess an additional acidic group are present in ionized form at the high pH of the assay and are not extractable at all.     

Spectrophotometric determination of iron and boron in soil extracts using a multi-syringe flow injection system

In the last decade, significant advances in flow analysis have been reported, namely the extensive use of computer-controlled devices to enhance the autonomy and performance of analysers. In the present work, computer-controlled multi-syringe flow injection systems are proposed to perform the spectrophotometric determination of available iron and boron in soil extracts. The methodologies were based on the formation of ferroin complex (determination of iron) and azomethine-H reaction (determination of boron). Both determinations were performed in manifolds with similar configurations by changing the reagents present in the different syringes. In the determination of iron, elimination of Schlieren effect in the detection system was achieved through the binary sampling approach, where a three-way valve was actuated to intercalate small slugs of sample and reagent, promoting better mixing conditions for solutions with different values of refractive index. In the determination of boron, in-line sample blank measurement was attained by omitting the introduction of reagent through software control, without manifold reconfiguration. Linear calibration curves were established between 0.50 and 10.0 mg Fe l⁻¹ and between 0.20 and 4.0 mg B l⁻¹. No systematic difference was found when soil extracts were analysed by the proposed methodologies and compared to the respective reference procedures.     

A flow-based procedure with solenoid micro-pumps for the spectrophotometric determination of uric acid in urine

The determination of uric acid in urine shows clinical importance, once it can be related to human organism dysfunctions, such as gout. An analytical procedure employing a multicommuted flow system was developed for the determination of uric acid in urine samples. Cu(II) ions are reduced by uric acid to Cu(I) that can be quantified by spectrophotometry in the presence of 2,2′-biquinoline 4,4′-dicarboxylic acid (BCA). The analytical response was linear between 10 and 100 μmol L^− 1 uric acid with a detection limit of 3.0 μmol L^− 1 (99.7% confidence level). Coefficient of variation of 1.2% and sampling rate of 150 determinations per hour were achieved. Per determination, 32 μg of CuSO₄ and 200 μg of BCA were consumed, generating 2.0 mL of waste. Recoveries from 91 to 112% were estimated and the results for 7 urine samples agreed with those obtained by the commercially available enzymatic kit for determination of uric acid. The procedure required 100-fold dilution of urine samples, minimizing sample consumption and interfering effects. In order to avoid the manual dilution step, on-line sample dilution was achieved by a simple system reconfiguration attaining a sampling rate of 95 h^− 1.     

流动注射光度法直接测定海水中的微量苯胺

基于苯胺与亚硝酸盐的重氮化反应及反应产物与甲萘酚的显色,借助流动分析技术,实现了海水中苯胺含量的分析测定。体系以30.9g/L的NaCl做载液、人工海水配制标准样品,对各个影响因素进行了优化。苯胺浓度在0.01～1.0mg/L范围内与相对峰高呈线性关系,线性方程ΔH(mV)=200.53ρ+1.0728(n=8,ρ为苯胺浓度mg/L),相关系数R2=0.9982。方法的检出限(3σ)为0.005mg/L,相对标准偏差(RSD)为4.8%(n=11)。考察了共存离子、不同盐度样品对分析测定的影响。用于实际海水样品的分析,回收率为95.8%～106.6%。     

Liquid-liquid extraction procedure exploiting multicommutation in flow system for the determination of molybdenum in plants

A liquid-liquid extraction flow analysis procedure for the spectrophotometric determination of molybdenum in plants at μg l⁻¹ level is described. The flow network comprised a set of solenoid valves assembled to implement the multicommutation approach under microcomputer control. Radiation source (LED, 475 nm), detector (photodiode) and separation chamber were nested together with the flow cell comprising a compact unit. The consumption of reagents (potassium thiocyanate and stannous chloride) and also extracting solvent (isoamyl alcohol) were optimized to 32 mg and 200 μl per determination, respectively. Accuracy was assessed by comparing results with those obtained with ICP-OES and no significant difference at 95% confidence level was observed. Other favorable characteristics such as a linear response ranging from 25 to 150 μg l⁻¹ molybdenum (r=0.999); detection limit of 4.6 μg l⁻¹ sample throughput of 25 determinations per hour and relative standard deviation of 2.5% (n=10) were also achieved.     

Spectrophotometric flow-injection determination of copper and nickel in plant digests exploiting differential kinetic analysis and multi-site detection

A novel strategy for implementing differential reaction-rate methods in flow-injection analysis is proposed and applied to the determination of copper and nickel in plant digests using 2-(5-brom-2-pyridylazo)-5-(diethylamino)-phenol (Br-PADAP) as the color-forming reagent. Multi-site detection is involved, therefore the flow cell is displaced between two monitoring sites, and the analytical signals refer to different conditions of sample dispersion, reaction development and timing.The system handles 20 samples h⁻¹ and requires 0.32 mg Br-PADAP per determination. Signal additivity was evaluated within 98 and 102%, and linear responses (r > 0.999; n = 6) were verified for both copper and nickel up to 0.80 mg l⁻¹. Detection limits of 0.01 and 0.04 mg l⁻¹ Cu and Ni were estimated by considering the highest concentration of the counter analyte. Results are precise (R.S.D. < 2%) and in agreement with ICP-OES (95% confidence level). Potentialities and limitations of the approach are discussed.     

Flow-injection Spectrophotometric Determination of Uric Acid in Urine via Prussian Blue Reaction

A simple and sensitive flow injection(FI) spectrophotometric method was reported for the determination of uric acid based on the reduction of Fe(III)/ferricyanide in the presence of uric acid. The in situ reduced ions reacted with unreduced portion of ferricyanide/Fe(III) to form soluble Prussian blue, which was monitored at an absorption wavelength of 735 nm. The optimized conditions allow a linear calibration graph in a concentration range of 1―100 μmol/L. The relative standard deviation was in a range of 0.5%―2.5%, with a detection limit(3σ blank) of 0.3 μmol/L and a sampling frequency of 60 injection/h was obtained. The effect of common substances present in human physiological fluids on the determination of uric acid was examined. The method was applied to determining uric acid in human urine samples with the recoveries in a range of 96%―105%. The results agree well with those by spectrophotometric reference method at a confidence level of 95%. Spectrophotometric procedures for uric acid determination in clinical samples were reviewed briefly.     

流动注射化学发光法快速测定尿液中左亚叶酸钙

在碱性介质中, 左亚叶酸钙对鲁米诺-K3Fe(CN)6体系有显著的增敏作用, 据此, 建立了一种简单、快速测定左亚叶酸钙的流动注射化学发光新方法. 在优化的实验条件下, 该法测定左亚叶酸钙的线性范围为5.0×10-8～1.0×10-5 g/mL; 检出限(3σ)为2.0×10-8 g/mL; 对浓度为1.0×10-6 g/mL的样品进行11次平行测定, 相对标准偏差为1.3%. 将此法用于尿液中左亚叶酸钙的测定, 同时进行回收率实验.     

Multicommutated flow analysis system for determination of creatinine in physiological fluids by Jaffe method

For the needs of photometric determination of creatinine according to Jaffe protocol a dedicated paired emitter detector diode (PEDD) detector has been developed. This PEDD device has been constructed in the compact form of flow-through cell (30 μL total volume and 7 mm optical pathlength) integrated with 505 nm LED-based emitter and 525 nm LED-based detector compatible with multicommutated flow analysis (MCFA) system. This fully mechanized MCFA system configured of microsolenoid valves and pumps is operating under microprocessor control. The developed analytical system offers determination of creatinine in the submillimolar range of concentrations with detection limit at ppm level. The throughput offered by the system operating according to multi-point fixed-time procedure for kinetic measurements is 15–40 samples per hour depending on the mode of measurements. The developed PEDD-based MCFA system has been successfully applied for the determination of creatinine in real samples of human urine as well as serum. The developed sampling unit used the system is free from effects caused by differences in sample viscosity.     

Simultaneous determination of serotonin and creatinine in urine by combining two ultrasound-assisted emulsification microextractions with on-column stacking in capillary electrophoresis

This article describes the development of a rapid, simple, and sensitive analytical approach for the simultaneous determination of serotonin (5‐hydroxytryptamine) and creatinine in urine samples by combining two ultrasound‐assisted emulsification microextractions (USAEMEs) in series with on‐column stacking in CE. This serial USAEME procedure comprises analytes extraction from the donor solution (urine with K₂CO₃ additive) to an organic solvent followed by a back‐extraction from the organic phase into a small volume of hydrochloric acid. After 15 min of sample pretreatment, the acidic acceptor solution was analyzed directly on CE in the mode of capillary zone electrophoresis. The adoption of HCl as the acceptor phase not only provided effective back‐extraction but also facilitated pH‐mediated on‐column stacking in CE analysis. About 360‐fold sensitivity enhancement was achieved for serotonin detection. The limits of detection were 7.9 nM for serotonin and 13.3 μM for creatinine, respectively. Satisfactory results were obtained with respect to precision and recovery. The proposed method has been demonstrated to be convenient and effective for the analysis of real urine samples. We believe that two USAEMEs in series will find wide applications in simplified sample pretreatment prior to CE analysis.     

Automatic flow procedure for the determination of glycerol in wine using enzymatic reaction and spectrophotometry

An automatic flow procedure for the determination of glycerol in wines by employing a flow system based on multicommutation and enzymatic reaction is described. Glycerol dehydrogenase was immobilized on aminopropyl glass beads and packed into a column that was coupled to the flow system. The NADH produced by the enzymatic reaction was monitored by spectrophotometry at 340 nm and its radiation absorption presented a relationship with glycerol concentration. The system manifold comprised a set of three-way solenoid valves controlled by a microcomputer, which was furnished with electronic interfaces and runs a software that was designed to carry out on-line sample dilution, reagent addition, and data acquisition. The procedure allows the determination of glycerol in wine samples without any prior pretreatment. The procedure presented as profitable features a linear response range between 2.0 and 10.0 g l⁻¹ glycerol (R=0.998), a detection limit of 0.006 g l⁻¹ glycerol, a relative standard deviation of 1.8% (n=14) for a typical wine sample presenting 5.3 g l⁻¹ glycerol, a sampling throughput of 33 determinations per hour, and a NAD⁺ consumption of 0.8 mg per determination. The results were compared with those obtained using a reference method and no significant difference at 90% confidence level was observed.     

Flow injection kinetic spectrophotometric determination of trace amounts of Se(IV) in seawater

A simple, accurate, sensitive and selective flow injection catalytic kinetic spectrophotometric method for rapid determination of trace amounts of selenium is proposed in this paper. The proposed method is based on the accelerating effect of Se(IV) on the reaction of ethexlenediamine tetrecetic acid disodium salt (EDTA) and sodium nitrate with ammonium iron(II) sulfate hexahydrate in acidic media. The absorbance intensity was registered in this reaction solution at 440 nm. The calibration graph is linear in the range of 5 × 10⁻⁹-2 × 10⁻⁷ and 2 × 10⁻⁷-2 × 10⁻⁶ g ml⁻¹. The detection limit is 2 × 10⁻⁹ g ml⁻¹. The relative standard deviation was 3.4% for 5 × 10⁻⁸ g ml⁻¹ Se(IV) (n = 11), 2.7% for 5 × 10⁻⁷ g ml⁻¹ Se(IV) (n = 11). This method is very simple, rapid and suitable for automatic and continuous analysis. The presented system has been applied successfully to determination of Se(IV) of seawater samples.