Silica‐bonded S‐sulfonic Acid as a Recyclable Catalyst for Synthesis of 2,3‐Dihydroquinazolin‐4(1H)‐ones

2,3‐Dihydroquinazolin‐4(1H)‐one derivatives were synthesized via a one‐pot, three component reaction of isatoic anhydride and an aromatic aldehyde with ammonium acetate or primary amine catalyzed by silica‐bonded S‐sulfonic acid in ethanol at 80°C. The reaction work‐up is simple and the catalyst is easily separated from the products by filtration. The heterogeneous catalyst was recycled for ten runs upon the condensation reaction of isatoic anhydride and 4‐chlorobenzaldehyde with ammonium acetate without losing its catalytic activity.     

Arborescent polypeptides from γ‐benzyl l‐glutamic acid

The synthesis of arborescent polymers with poly(γ‐benzyl L‐glutamate) (PBG) side chains was achieved through successive grafting reactions. The linear PBG building blocks were produced by the ring‐opening polymerization of γ‐benzyl L‐glutamic acid N‐carboxyanhydride initiated with n‐hexylamine. The polymerization conditions were optimized to minimize the loss of amino chain termini in the reaction. Acidolysis of a fraction of the benzyl groups on a linear PBG substrate and coupling with linear PBG using a carbodiimide/hydroxybenzotriazole promoter system yielded a comb‐branched or generation zero (G0) arborescent PBG. Further partial deprotection and grafting cycles led to arborescent PBG of generations G1 to G3. The solvent used in the coupling reaction had a dramatic influence on the yield of graft polymers of generations G1 and above, dimethylsulfoxide being preferable to N,N‐dimethylformamide. This grafting onto scheme yielded well‐defined (M_w/M_n ≤ 1.06), high molecular weight arborescent PBG in a few reaction cycles, with number‐average molecular weights and branching functionalities reaching over 10⁶ and 290, respectively, for the G3 polymer. α‐Helix to coiled conformation transitions were observed from N,N‐dimethylformamide to dimethyl sulfoxide solutions, even for the highly branched polymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5270–5279     

Newborn screening for 3‐hydroxy‐3‐methylglutaric aciduria using direct analysis in real‐time mass spectrometry

A novel method utilizing ambient thermal desorption ionization with a direct analysis in real‐time source integrated with mass spectrometry (DART‐MS) was established and applied to the rapid analysis of 3‐hydroxy‐3‐methylglutaric (3‐HMG) acid in the neonatal urine. Instrument parameter settings were optimized to obtain high sensitive and accurate determination of 3‐HMG acid. The use of helium gas heated to temperature of 400°C was observed to permit deprotonation, 3‐HMG acid producing an abundant (M‐H)^? (m/z 161) in the negative ion mode. The calibration curve was determined to be linear over the range of 0.05‐5 mg/L, with the correlation coefficient r = 0.9988 and the relative standard deviations (n = 6) in the range of 1.5‐11.8%. The limit of detection was 0.002 mg/L, and the limit of quantitation was 0.007 mg/L. The recoveries ranged from 88.0% to 123.1%. Four urine samples from patients and four simulated urine samples were investigated. The results of DART‐MS were in agreement with the values determined using established methods at the hospitals. The proposed method demonstrated significant potential in the application of the high‐throughput screening in newborn screening.     

Application of two‐dimensional near‐infrared (2D‐NIR) correlation spectroscopy to the discrimination of three species of Dendrobium

The objective of this paper was to apply two‐dimensional (2D) near‐infrared (NIR) correlation spectroscopy to the discrimination of three species of Dendrobium. Generalized 2D‐NIR correlation spectroscopy was able to enhance spectral resolution, simplify the spectrum with overlapped bands and provide information about temperature‐induced spectral intensity variations that was hard to obtain from one‐dimensional NIR spectroscopy. The FT‐NIR spectra were measured over a temperature range of 30–140°C. The 2D synchronous and asynchronous spectra showed remarkable differences within the range of 5600–4750 cm⁻¹ between different species of Dendrobium. Copyright © 2009 John Wiley & Sons, Ltd.     

Microwave‐induced Stereoselectivity in Synthesis of trans‐4‐Aryl‐3‐methyl‐6‐oxo‐4,5,6,7‐tetrahydro‐2H‐pyrazolo[3,4‐b]pyridine‐5‐carbonitriles

A facile synthesis of trans isomers of 4‐aryl‐3‐methyl‐6‐oxo‐4,5,6,7‐tetrahydro ‐ 2H ‐ pyrazolo[3,4‐b]pyridine‐5‐carbonitriles via three‐component condensation reaction of an aldehyde, 3‐amino‐5‐methylpyrazole and ethyl cyanoacetate in acetonitrile has been developed under microwave irradiation. This one‐pot reaction proceeds without any catalyst in short times and gives the product in high selectivities and high yields.     

Facile and Selective Synthesis of 4‐Methyl‐ and 4‐Phenylthiosemicarbazide (=N‐Methyl‐ and N‐Phenylhydrazinecarbothioamide) Derivatives of Benzil (=1,2‐Diphenylethane‐1,2‐dione)

A selective synthesis of 4‐methylthiosemicarbazide (=N‐methylhydrazinecarbothioamide; 4a ) derivatives by reaction with benzil (=1,2‐diphenylethane‐1,2‐dione; 3 ) is described. The reaction conditions determined the condensation product formed. The most important factor was the acid used: in the presence of conc. HCl solution, the open‐chain 2 : 1 compound 1a was exclusively obtained, whereas in the presence of 2M HCl, the cyclic 1 : 1 condensation product 2a was formed. The alcohol used, the presence of H₂O, and the time of heating were additional crucial factors. The new cyclic compound 2a with a MeO group was exclusively formed when working under high‐dilution conditions. The reaction with the 4‐phenyl derivative 4b gave new cyclic compounds as the major products under all conditions used (Scheme).     

Synthesis of a New Library of Pyrano‐phenazine Derivatives via a Novel Three‐Component Protocol

The pyrano‐phenazine derivatives 6 were synthesized by an efficient procedure using the reaction between benzo[a]phenacin‐5‐ols with the condensation product of an aldehyde with Meldrum's acid in the presence of a catalytic amount of Et₃N at ambient temperature. The procedure is very simple, and products could be separated from the reaction media by simple filtration. High functional‐group tolerance both in the benzo[a]phenazin‐5‐ol and aldehyde moieties, facile reaction procedure, medium‐to‐high yields, and simple separation of the products from the reaction media are the advantages of this route.     

Synthesis and characterization of novel poly(ester‐carbonate)s by copolymerization of trans‐4‐hydroxy‐L‐proline with cyclic carbonate

The melt ring‐opening/condensation reaction of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline (N‐CBz‐Hpr) with cyclic carbonate [trimethylene carbonate (tri‐MC) or tetramethylene carbonate (tetra‐MC)] at a wide range of molar fractions in the feed produced new degradable poly(ester‐carbonate)s. The influence of reaction conditions such as polymerization time and temperature on the yield and inherent viscosity of the copolymers was investigated. The polymerizations were carried out in bulk at 140 °C with 1.5 wt % stannous octoate as a catalyst for 30 h. The poly(ester‐carbonate)s obtained were characterized by Fourier transform infrared spectroscopy, ¹H NMR, differential scanning calorimetry, gel permeation chromatography, and Ubbelohde viscometry. The copolymers synthesized exhibited moderate molecular weights with rather narrow molecular weight distributions. The values of the glass‐transition temperature (T_g) of the copolymers depend on the molar fractions of cyclic carbonate. For the poly(N‐CBz‐Hpr‐co‐tri‐MC) system, with a decreased tri‐MC content from 93 to 16 mol %, the T_g increased from ?10 to 60 °C. Similarly, for the poly(N‐CBz‐Hpr‐co‐tetra‐MC) system, when the tetra‐MC content decreased from 80 to 8 mol %, the T_g increased from ?18 to 52 °C. The relationship between the poly(N‐CBz‐Hpr‐co‐tri‐MC) T_g and the compositions was in approximation with the Fox equation. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐tri‐MC)s was evaluated from weight‐loss measurements. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1435–1443, 2003     

Synthesis and Characterisation of Polyamides Containing 1,4‐Dithiin‐2,3 : 5,6‐tetrayl Diimide Structures

Polyamides containing 1,4‐dithiin‐2,3 : 5,6‐tetrayl diimide structures were synthesised by condensation reaction of bis[N,N′‐(4‐chlorocarbonylphenyl)‐1,4‐dithiin‐2,3 : 5,6‐tetrayl diimide] ( 3 ) with various aromatic diamines. Monomer 3 was synthesised by nucleophilic substitution of N‐(4‐carboxyphenyl)‐3,4‐dichloromaleimide ( 1 ) with sodium sulfide nonahydrate. Their structures were confirmed by IR and UV spectroscopy, as well as elemental analysis. The polymers were characterised by viscometric measurements, softening points and thermogravimetric data. They showed good solubility in aprotic solvents and high thermal stability with the decomposition temperature being in the range 392–415°C.     

Photoinduced and thermal reactions of α‐cyano‐β‐bromomethylcinnamide with 1‐benzyl‐1,4‐dihydronicotinamide

The photoinduced reaction of a mixture of (Z)‐α‐cyano‐β‐bromomethylcinnamide (1) and (E)‐α‐cyano‐β‐bromomethylcinnamide (2) with 1‐benzyl‐1, 4‐dihydronicotinamide produces a mixture of the (E)‐ and (Z)‐ isomers of α‐cyano‐β‐methylcinnamide (3 and 4). Using spin‐trapping technique for monitoring reactive intermediate, it is shown that the reaction proceeds via electron transfer‐debromination‐H abstraction mechanism. The thermal reaction of the same substrate with BNAH at 60°C in the dark gives three products: the (E)‐ and (Z)‐isomers of α‐cyano‐β‐methylcinnamide and a dehydrodimeric product; 2, 7‐dicyano‐3, 6‐diphenylocta‐2, 4, 6‐trien‐1, 8‐dioic amide (7). Based on product analysis, scavenger experiment and cyclic voltammetry, an electron transfer‐debromination‐disproportionation mechanism is proposed.     

Acid‐promoted double ring‐opening reaction of bicyclobis (γ‐butyrolactone) with alcohol and its application to polyester synthesis

Bicyclobis(γ‐butyrolactone) (BBL) bearing methyl group 1a reacted with benzyl alcohol (BnOH) in the presence of p‐toluenesulfonic acid (p‐TsOH) through the double ring‐opening of the bislactone structure to afford the corresponding adduct 2a bearing carboxyl group. The resulting carboxyl group underwent condensation with BnOH to afford the corresponding diester 3a . The second step was quite slow at ambient temperature; however, it was efficiently accelerated by elevating temperature to 120 °C or performing under reduced pressure at 80 °C to afford 3a in an excellent yield. Based on these results, the reaction of 1a with xylene‐α,α‐diol (XyD) was carried out in chlorobenzene at 120 °C to obtain the corresponding polyester bearing ketone group in the side chain. The condensation reaction in the second step was effectively promoted by simultaneous removal of water under reduced pressure. BBLs 1b and 1c bearing reactive groups, isopropenyl and chloromethyl, respectively, were also employed as monomers efficiently. Their reactions with XyD gave the corresponding reactive polyesters bearing methacryloyl and chloroacetyl moieties, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and Solid‐state Reaction of 1‐[3′‐(Benzotriazol‐2″‐yl)‐4′ ‐hydroxybenzoyl]‐3‐methyl‐5‐pyrazolones

A new kind of UV stabilizers, 1‐(3′‐(benzotriazol‐2″‐yl)‐4′‐hydroxy‐benzoyl)‐3‐methyl‐5‐pyrazolones (1a‐d), was synthesized with the aim to bind them chemically to certain polymers. The reaction of 1d with substituted benzaldehydes 4 in the molten state at 150°C and in the solid state at room temperature produced the condensation products l‐(3′‐(5″‐chlorobenzotriazol‐2″‐yl)‐4′‐hydroxyl‐5′‐chlorobenzoyl)‐3‐methyl‐4‐arylmethylene‐5‐pyrazolones (2) and 4,4′‐arylmethylene‐bis [1‐(3′‐(5″‐chloro‐benzotriazol‐2″‐yl)‐4′‐hydroxy‐5′‐chloro‐benzoyl)‐3‐methyl‐5‐pyrazolone] s (3), respectively, as the major product. On the other hand, the reaction of 1d with 4 at 50°C in chloroform solution proceeded non‐selectively to give a mixture of 2 and 3.     

Synthesis and characterization of novel polyamide‐imides containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide‐dicarboxylic acid, 2,2′‐dimethyl‐4,4′‐bis(4‐trimellitimidophenoxy)biphenyl (DBTPB), containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by the condensation reaction of 2,2′‐dimethyl‐4,4′‐bis(4‐minophenoxy)biphenyl (DBAPB) with trimellitic anhydride in glacial acetic acid. A series of new polyamide‐imides were prepared by direct polycondensation of DBAPB and various aromatic diamines in N‐methyl‐2‐pyrrolidinone (NMP), using triphenyl phosphite and pyridine as condensing agents. The polymers were produced with high yield and moderate to high inherent viscosities of 0.86–1.33 dL · g⁻¹. Wide‐angle X‐ray diffractograms revealed that the polymers were amorphous. Most of the polymers exhibited good solubility and could be readily dissolved in various solvents such as NMP, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide (DMF), dimethyl sulfoxide, pyridine, cyclohexanone, and tetrahydrofuran. These polyamide‐imides had glass‐transition temperatures between 224–302 °C and 10% weight loss temperatures in the range of 501–563 °C in nitrogen atmosphere. The tough polymer films, obtained by casting from DMAc solution, had a tensile strength range of 93–115 MPa and a tensile modulus range of 2.0–2.3 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 63–70, 2001     

Synthesis and NMR characterization of 6‐Phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose

Cellulose ( 1 ) was converted for the first time to 6‐phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 6 ) in 33% overall yield. Intermediates in the five‐step conversion of 1 to­ 6 were: 6‐O‐tritylcellulose ( 2 ), 6‐O‐trityl‐2,3‐di‐O‐methylcellulose ( 3 ), 2,3‐di‐O‐methylcellulose ( 4 ); and 6‐bromo‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 5 ). Elemental and quantitative carbon‐13 analyses were concurrently used to verify and confirm the degrees of substitution in each new polymer. Gel permeation chromotography (GPC) data were generated to monitor the changes in molecular weight (DP_w) as the synthesis progressed, and the compound average decrease in cellulose DP_w was ～ 27%. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to characterize the decomposition of all polymers. The degradation temperatures ( °C) and percent char at 500 °C of cellulose derivatives 2 to 6 were 308.6 and 6.3%, 227.6 °C and 9.7%, 273.9 °C and 30.2%, 200.4 °C and 25.6%, and 207.2 °C and 27.0%, respectively. The glass transition temperature (T_g) of­6‐O‐tritylcellulose by dynamic mechanical analysis (DMA) occurred at 126.7 °C and the modulus (E′, Pa) dropped 8.9 fold in the transition from ?150 °C to + 180 °C (6.6 × 10⁹ to 7.4 × 10⁸ Pa). Modulus at 20 °C was 3.26 × 10⁹ Pa. Complete proton and carbon‐13 chemical shift assignments of the repeating unit of the title polymer were made by a combination of the HMQC and COSY NMR methods. Ultimate non‐destructive proof of carbon–carbon bond formation at C6 of the anhydroglucose moiety was established by generating correlations between resonances of CH₂6 (anhydroglucose) and C1′, H2′, and H6′ of the attached aryl ring using the heteronuclear multiple‐bond correlation (HMBC) method. In this study, we achieved three major objectives: (a) new methodologies for the chemical modification of cellulose were developed; (b) new cellulose derivatives were designed, prepared and characterized; (c) unequivocal structural proof for carbon–carbon bond formation with cellulose was derived non‐destructively by use of one‐ and two‐dimensional NMR methods. Copyright © 2002 John Wiley & Sons, Ltd.     

Synthesis of 2‐Aryl‐1‐arylmethyl‐1H‐1,3‐benzimidazole Derivatives Using Silica‐bonded Propyl‐S‐sulfonic Acid as Recyclable Solid Acid Catalyst

A highly selective synthesis of 2‐aryl‐1‐arylmethyl‐1H‐1,3‐benzimidazoles from the reaction of o‐phenylenediamine and aromatic aldehydes in the presence of silica‐bonded propyl‐S‐sulfonic acid (SBSSA) at 80°C in water in good to excellent yields was developed.     

Solid‐state amidization and imidization reactions in vapor‐deposited poly(amic acid)

The condensation polymerization of 4,4′‐oxydianiline with pyromellitic dianhydride for the formation of poly(amic acid) and the subsequent imidization for the formation of polyimides were investigated for films prepared with vapor‐deposition polymerization techniques. Fourier transform infrared spectroscopy, thermal analysis, and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry of films at different temperatures indicated that additional solid‐state polymerization occurred before imidization. The experiments revealed that, upon vapor deposition, poly(amic acid) oligomers formed that had a number‐average molecular weight of about 1500 Da. Between 100–130 °C, these chains underwent an additional condensation reaction and formed slightly higher molecular weight oligomers. Calorimetry measurements showed that this reaction was exothermic [enthalpy of reaction (ΔH) ～ ?30 J/g] and had an activation energy of about 120 kJ/mol. The experimental ΔH values were compared with results from ab initio molecular modeling calculations to estimate the number of amide groups formed. At higher temperatures (150–300 °C), the imidization of amide linkages occurred as an endothermic reaction (ΔH ～ +120 J/g) with an activation energy of about 130 kJ/mol. The solid‐state kinetics depended on the reaction conversion as well as the processing conditions used to deposit the films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5999–6010, 2004     

First Synthesis of Ferrocenyl‐Substituted 1,2‐Dihydro‐2‐oxopyridine‐3‐carbonitriles

In the present investigation, the first incorporation of both ferrocene scaffold and 1,2‐dihydro‐2‐oxopyridine‐3‐carbonitrile pharmacophore leading to a series of structurally novel ferrocene‐based hybrids has been achieved, involving the condensation reaction of ferrocenyl substituted chalcones with 2‐cyanoacetamide in a freshly prepared EtONa solution at 70°. The molecular structures of these newly synthesized products were confirmed by IR, and ¹H‐ and ¹³C‐NMR analyses.     

Synthesis and properties of new organo‐soluble and strictly alternating aromatic poly(ester‐imide)s from 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide and bisphenols

A series of new strictly alternating aromatic poly(ester‐imide)s having inherent viscosities of 0.20–0.98 dL/g was synthesized by the diphenylchlorophosphate (DPCP) activated direct polycondensation of the preformed imide ring‐containing diacid, 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide (I), with various bisphenols in a medium consisting of pyridine and lithium chloride. The diimide–diacid I was prepared from the condensation of 3,3‐bis[4‐(4‐aminophenoxy)phenyl]phthalide and trimellitic anhydride. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone (NMP) and N,N‐dimethylacetamide (DMAc). Transparent and flexible films of these polymers could be cast from their DMAc solutions. The cast films had tensile strengths ranging 66–105 MPa, elongations at break from 7–10%, and initial moduli from 1.9–2.4 GPa. The glass‐transition temperatures of these polymers were recorded between 208–275 °C. All polymers showed no significant weight loss below 400 °C in the air or in nitrogen, and the decomposition temperatures at 10% weight loss all occurred above 460 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1090–1099, 2000     

Copper(II)‐Catalyzed Synthesis of N‐Substituted‐3‐amino‐4‐cyano‐isoquinoline‐1(2H)‐ones by the Reaction of N‐Substituted‐2‐iodobenzamides with Malononitrile

A novel Cu(OAc)₂·H₂O catalyzed coupling reaction of N‐substituted‐2‐iodobenzamides with malononitrile to afford N‐substituted‐3‐amino‐4‐cyano‐isoquinoline‐1(2H)‐ones is described. The reaction proceeded in DMSO at 90°C for 5 h in nitrogen without external ligands.     

Preparation and properties of high‐pretilt‐angle polyimides based on an alicyclic dianhydride and long alkyloxy side‐group‐containing diamines

A series of polyimides were prepared by a solution polycondensation reaction between 3‐carboxylmethylcyclopentane‐1,2,4‐tricarboxylic dianhydride and 4‐alkyloxybenzene‐1,3‐diamines in N‐methyl‐2‐pyrrolidone and chemical imidization with triethylamine and acetic anhydride. These polyimides possess great organo‐solubility, high optical transparency, and high pretilt angles. They are soluble not only in strong polar aprotic organic solvents such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, m‐cresol, and 1,4‐butyrolactone but also in common low‐boiling‐point solvents such as chloroform and tetrahydrofuran, and some are even soluble in acetone. They exhibit high transparency at wavelengths greater than 320 nm. They can generate pretilt angles greater than 5°, and some can even achieve pretilt angles greater than 10°. The pretilt angle of a polyimide increases with the increasing length of the alkyloxy side group. The polyimides possess glass‐transition temperatures between 180 and 230 °C and thermal decomposition temperatures (onset temperatures) of about 435 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1943–1950, 2000