An improved method for determination of light hydrocarbons in stabilized crude oil

Summary This paper reports a quick, and simple method for quantitative determination of C₂ to C₆ hydrocarbons in stabilized crude oil without using a back flush system. A mixture of crude oil and internal standard is injected into a GC equipped with a 6 meter length of fused silica capillary as a guard column. The light hydrocarbons are separated individually up to the last peak of the hexane group with the heavier components trapped in the guard column. The total analysis time for each sample is 15 minutes. The base line is table for up to 15 consecutive analyses. The guard column and the injector port are then reconditioned by simply heating them for one hour at 300 °C.     

Electrospray ionization mass spectrometric detection of low polar compounds by adding NaAuCl4

Liquid chromatography electrospray ionization mass spectrometry (LC/ESI/MS) has been widely used for various analyses. However, it is difficult to use LC/ESI/MS for the analysis of low polar compounds, such as polycyclic aromatic hydrocarbons. It is well known that AuCl₄^? ion decomposes to AuCl₃ by heating, and AuCl₃ is a strong π‐electrophilic Lewis acid. Low polar compounds (pyrene, benzo[a]pyrene, perylene, benzo[ghi]perylene, dibenzothiophene and p‐dimethoxybenzene) were detected by ESI/MS in the positive ion mode by adding NaAuCl₄. The low polar compound interacts with AuCl₃ formed at the ESI interface, and undergoes electron transfer to AuCl₃. The radical cation of the low polar compound was then detected by MS. In addition, the LC/ESI/MS determination of polycyclic aromatic hydrocarbons by the post‐column addition of NaAuCl₄ was studied. © 2016 The Authors Journal of Mass Spectrometry Published by John Wiley & Sons Ltd     

Laser desorption/ionization determination of molecular weight distributions of polyaromatic carbonaceous compounds and their aggregates

Molecular weight distributions (MWDs) of model polyaromatic hydrocarbons (PAHs) and complex asphaltene samples have been investigated in laser desorption/ionization mass spectrometry (LDI-MS) experiments. Special efforts are devoted to the characterization of aggregation effects during the desorption process. It is found that non-covalent clusters of the PAHs and asphaltenes form readily in the desorbing plume. Aggregation is favoured in the experiments performed on dense samples at high laser energy and under continuous ion extraction conditions. In the absence of polar groups in the analyte molecules, the aggregation propensity correlates well with the size of the polycondensed system and with its degree of pericondensation, in qualitative agreement with previous theoretical predictions. For the polydispersed asphaltenes from two different crude oils, MWDs peaking at masses smaller than 500 amu with a high-mass tail extending up to about 3000 amu have been observed, yielding average weights around 900 amu. Such MWDs are in good agreement with previous mass spectrometric measurement, as well as with diffusion studies in solution. In addition, stable asphaltene aggregates have been detected giving rise to two broad bands in the mass spectrum corresponding to average molecular weights of 2200-3100 amu and 15,000-19,000 amu, respectively. It is concluded that the strong aggregation propensity of asphaltenes is likely to be responsible for the apparent inconsistency between the MWD for these compounds determined by different groups in independent LDI-MS experiments. The reliability of different sample preparation procedures, including solvent-free methods, is discussed, and strategies are outlined that serve to apply the potentiality of LDI mass spectrometry to the characterization of covalent and non-covalent compounds in complex carbonaceous systems.     

Laser desorption/ionization techniques in the characterization of high molecular weight oil fractions. Part 1: asphaltenes

The molecular weight distribution of the asphaltene fractions of two types of crude oils from two different Italian fields (samples 1 and 2) was investigated. The analytical tools used to perform these analyses were matrix assisted laser desorption ionization (MALDI) and laser desorption ionization (LDI) mass spectrometry. After observing that the use of the matrix (as well as the addition of Ag+) did not improve the quality of the data compared to that obtained in LDI conditions, all further measurements were performed with the latter technique. Operating under usual conditions of laser power and delay time, a very low resolution was observed, showing only macroscopic differences between the two samples in the molecular weight distribution of the different components. An accurate study on the possible reasons of this undesirable behavior indicates that it can originate from space charge phenomena occurring either in the ion source region or during the flight. A valid parameterization of the delay time and the laser power allowed higher quality spectra to be obtained. Surface-enhanced laser desorption ionization (SELDI) measurements were also performed using normal phase (silica) as the sample holder surface. Under these conditions, better results are obtained, proving that the sample-surface interaction is important to achieve, by means of laser irradiation, a homogeneous set of product ions. Both asphaltene samples were fractionated in five subfractions by gel-permeation chromatography (GPC) to obtain a better separation of the molecular weight distributions; the related spectra confirmed these findings. By using different approaches, relevant and reproducible differences between the asphaltene fractions of the two oil samples were observed.     

MALDI‐FT‐ICR‐MS for archaeological lipid residue analysis

Soft‐ionization methods are currently at the forefront of developing novel methods for analysing degraded archaeological organic residues. Here, we present little‐used soft ionization method of matrix assisted laser desorption/ionization‐Fourier transform‐ion cyclotron resonance‐mass spectrometry (MALDI‐FT‐ICR‐MS) for the identification of archaeological lipid residues. It is a high‐resolution and sensitive method with low limits of detection capable of identifying lipid compounds in small concentrations, thus providing a highly potential new technique for the analysis of degraded lipid components. A thorough methodology development for analysing cooked and degraded food remains from ceramic vessels was carried out, and the most efficient sample preparation protocol is described. The identified components, also controlled by independent parallel analysis by gas chromatography‐mass spectrometry (GC‐MS) and gas chromatography‐combustion‐isotope ratio mass spectrometry (GC‐C‐IRMS), demonstrate its capability of identifying very different food residues including dairy, adipose fats as well as lipids of aquatic origin. The results obtained from experimentally cooked and original archaeological samples prove the suitability of MALDI‐FT‐ICR‐MS for analysing archaeological organic residues. Sample preparation protocol and identification of compounds provide future reference for analysing various aged and degraded lipid residues in different organic and mineral matrices.     

Mechanical properties of high‐density polyethylene and crosslinked high‐density polyethylene in crude oil and its components

The tensile and stress‐relaxation properties of an uncrosslinked and a loosely silane‐crosslinked high‐density polyethylene exposed to organic “crude‐oil” penetrants were assessed. The measurements were performed on penetrant‐saturated samples, surrounded by the organic liquid throughout the experiment. The penetrant solubilities in the two polymers were similar and in accordance with predicted values based on the solubility parameter method. The stiffness and strength of the swollen samples were significantly less than those of the dry samples, indicating a plasticization of the amorphous component. Raman spectroscopy on polyethylene exposed to deuterated n‐hexane revealed a penetrant‐induced partial melting/dissolution of the crystal surface and an intact crystal core component. The stress‐relaxation rates, within the time frame of the experiment (～1 s to 18 h), were approximately the same, independent of silane‐crosslinks and the presence of penetrants. This indicated that the mechanical α‐relaxation, which is the main relaxation process occurring in the measured time interval, was not affected by the penetrants. Consequently, its rate seemed to be independent of the crystal surface dissolution (decrease in the content of crystal‐core interface). The shape of the “log stress–log time” curves of the swollen samples was, however, different from that of the dry samples. This was most likely attributed to a time‐dependent saturation of penetrant to a higher level associated with the stretched state of the polymer sample. The silane crosslinks affected only the elongation at break, which was less than that of the uncrosslinked material. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 641–648, 2006     

On the determination of molecular weight distributions of asphaltenes and their aggregates in laser desorption ionization experiments

Molecular weight distributions (MWD) of asphaltenes and their aggregates have been investigated in laser desorption ionization (LDI) mass spectrometric experiments. A systematic investigation of the dependence of the measured MWD on the asphaltene sample density and on the laser pulse energy allows the assignment of most probable molecular weights within 300-500 amu and average molecular weights of 800-1000 amu for the monomeric asphaltenes, as well as for the estimation of the contribution from asphaltene clusters in typical LDI measurements. The results serve to reconcile the existing controversy between earlier mass spectrometric characterizations of asphaltenes based on laser desorption techniques by different groups. Furthermore, the MWD measurements performed on particularly dense samples yield an additional differentiated broad band peaking around 9000-10,000 amu and extending over 20,000 amu, not observed previously in LDI experiments, thereby revealing a strong propensity of the asphaltenes to form clusters with specific aggregation numbers, which is in qualitative agreement with previous theoretical predictions and with the interpretation of measurements performed with other techniques.     

Electrospray Lonization Fourier Transform Ion Cyclotron Resonance Mass Spectrometric Study on Sodium Azide Cluster Ions

Sodium azide has rarely been studied in gas phase or in the form of cluster ions and as a model of solid energetic substances and inorganic azide salt was ionized by electrospray ionization (ESI) and studied by high resolution Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometry (MS) systematically. This paper highlights the effects of experimental conditions on the formation of salt cluster and the collision activation dissociation pathways of cluster ions to develop a microscopic understanding of inorganic azide salt clusters.     

Conformational changes of ubiquitin during electrospray ionization as determined by in‐ESI source H/D exchange combined with high‐resolution MS and ECD fragmentation

In the paper, we have demonstrated the possibility of performing hydrogen/deuterium (H/D) exchange of proteins in the region of gas‐phase ion formation in an electrospray ion source by saturating the electrospray ionization source with vapors of a deuterating agent (D₂O or MeOD). In this region, charged droplets are shrinking and the protein ions transfer into the gas phase. As a model protein, we have used ubiquitin whose ion mobility spectrometry and gas‐phase H/D exchange in the vacuum part of a mass spectrometer demonstrated the presence of gas‐phase conformers with different cross sections and H/D exchange rates. In our experiments, we observed monomodal deuterium distributions for all solvents, charge states, desolvating capillary temperature and types of deuterating agent. Also, we found that the number of H/D exchanges increases with an increasing desolvating capillary temperature and decreasing charge state. We observed that solution composition (49 : 50 : 1 H₂O : MeOH : formic acid or 99 : 1 H₂O : formic acid) influences the charge‐state distribution but did not change the degree of H/D exchange for the same charge state. Electron‐capture dissociation fragmentation shows that higher charge states contain a segment that is protected from access by the deuterating agent. Copyright © 2014 John Wiley & Sons, Ltd.     

Electrospray ionization mass spectrometric study of end‐groups in peroxydicarbonate‐initiated radical polymerization

Initiation by diethyl peroxydicarbonate (E‐PDC), di‐n‐tetradecyl peroxydicarbonate (nTD‐PDC), di‐n‐hexadecyl peroxydicarbonate (nHD‐PDC), and di‐2‐ethylhexyl peroxydicarbonate (2EH‐PDC) of free‐radical polymerizations of methyl methacrylate in benzene solution was studied by end‐group analysis via electrospray ionization mass spectrometry (ESI‐MS). Unambiguous assignment of ESI‐MS peaks allows for identification of the type of radical that starts chain growth. In case of initiation by dialkyl peroxydicarbonates with linear alkyl groups, almost exclusively alkoxy carbonyloxyl species, which are the primary fragments from initiator decomposition, occur as end‐groups. With 2EH‐PDC, however, both the primary 2‐ethylhexoxy carbonyloxyl fragment and a second moiety, which is formed by decarboxylation of the 2‐ethylhexoxy carbonyloxyl radical, are clearly observed as end‐groups. The decarboxylation process is described by a concerted mechanism which involves a 1,5‐hydrogen shift reaction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6071–6081, 2008     

Improvement of mineral oil saturated and aromatic hydrocarbons determination in edible oil by liquid–liquid–gas chromatography with dual detection

Mineral oils, which are mainly composed of saturated hydrocarbons and aromatic hydrocarbons, are widespread food contaminants. Liquid chromatography coupled to gas chromatography with flame ionization detection represents the method of choice to determine these two families. However, despite the high selectivity of this technique, the presence of olefins (particularly squalene and its isomers) in some samples as in olive oils, does not allow the correct quantification of the mineral oil aromatic hydrocarbons fraction, requiring additional off‐line tools to eliminate them. In the present research, a novel on‐line liquid chromatography coupled to gas chromatography method is described for the determination of hydrocarbon contamination in edible oils. Two different liquid chromatography columns, namely a silica one (to retain the bulk of the matrix) and a silver‐ion one (which better retains the olefins), were coupled in series to obtain the mineral oil aromatic hydrocarbons hump free of interfering peaks. Furthermore, the use of a simultaneous dual detection, flame ionization detector and triple quadrupole mass spectrometer allowed us not only to quantify the mineral oil contamination, but also to evaluate the presence of specific markers (i.e. hopanes) to confirm the petrogenic origin of the contamination.     

Regioisomer characterization of triacylglycerols by non‐aqueous reversed‐phase liquid chromatography/electrospray ionization mass spectrometry using silver nitrate as a postcolumn reagent

Triacylglycerols (TAGs) provide a challenge for mass spectrometry (MS) analysis because of their complexity. In particular, for dietary, nutritional and metabolic purposes, the positional placement of fatty acids on the glycerol backbone of TAGs is a crucial aspect. To solve this problem, we have investigated the TAGs' fragmentation patterns using an ion trap mass spectrometer. A series of pure regioisomeric pairs of TAGs (POP/PPO, POO/OPO and OSO/SOO) were cationized by Ag⁺ after their separation by non‐aqueous reversed‐phase liquid chromatography (NARP‐LC) before MS to improve MS sensitivity. Electrospray ionization–MS (ESI‐MS) conditions were optimized in order to produce characteristic [M + Ag + AgNO₃]⁺ ions from each TAG, which were then fragmented to produce MS/MS spectra and then fragmented further to produce up to MS⁵ spectra. The observation of ions produced by LC‐MS⁵ of on‐line Ag⁺‐cationized TAG provided unambiguous information on the fatty acid distribution on the glycerol backbone. These strategies of MS to MS⁵ experiments were applied to identify components and to determine the regiospecificity of TAG within a complex mixture of lipids in natural oils. Copyright © 2010 John Wiley & Sons, Ltd.     

Characterization and application of a self‐aspirating electrospray source with pneumatic‐assisted ionization

A single gas‐assisted electrospray ion source developed for ambient mass spectrometry is introduced in this paper. Simultaneous self‐aspiration and electrospray could be achieved by using a constant sheath gas flow supplied from a mini air pump. A gas dynamic study of the spray module is carried out for structural optimization. The entire device exhibits a simplified design and has been systematically characterized through both simulated and experimental investigations. According to the results, the ion source exhibited satisfactory stability and the ability for quantitative operation in routine electrospray ionization mass spectrometry. Furthermore, the ion source can be operated as a desorption electrospray ionization source to perform direct desorption/ionization of the solid samples. The versatile source described here appears to provide a practical approach to perform ambient mass spectrometry analysis with unrestricted sampling operation, and the extensive gas dynamic studies together with the experimental characterization are believed to be helpful in building self‐aspirating spray devices. Copyright © 2017 John Wiley & Sons, Ltd.     

2,5‐Dihydroxybenzoic acid solution in MALDI‐MS: ageing and use for mass calibration

2,5‐Dihydroxybenzoic acid (DHB) is one of the most widely used and studied matrix compounds in matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry. However, the influence of ageing of the DHB solution on the MALDI mass spectra has not been yet systematically studied. In this work, the possible changes occurring in the acidified acetonitrile/water solution of the MALDI matrix compound DHB during 1‐year usage period have been monitored with MALDI‐Fourier transform ion cyclotron resonance mass spectrometer (MALDI‐FT‐ICR‐MS) and attenuated total reflectance Fourier transform infrared (ATR‐FT‐IR) spectroscopy. No significant ageing products have been detected. The ability of the aged DHB solution to act as a MALDI matrix was tested with two materials widely used in art and conservation – bone glue (a proteinaceous material) and shellac resin (a resinous material) – and good results were obtained. A number of peaks in the mass spectra measured from the DHB solution were identified, which can be used for internal calibration of the mass axis. Copyright © 2014 John Wiley & Sons, Ltd.     

Analysis of dammar resin with MALDI‐FT‐ICR‐MS and APCI‐FT‐ICR‐MS

Comprehensive analysis of high‐resolution mass spectra of aged natural dammar resin obtained with Fourier transform ion cyclotron resonance mass spectrometer (FT‐ICR‐MS) using matrix‐assisted laser desorption/ionization (MALDI) and atmospheric pressure chemical ionization (APCI) is presented. Dammar resin is one of the most important components of painting varnishes. Dammar resin is a terpenoid resin (dominated by triterpenoids) with intrinsically very complex composition. This complexity further increases with aging. Ten different solvents and two‐component solvent mixtures were tested for sample preparation. The most suitable solvent mixtures for the MALDI‐FT‐ICR‐MS analysis were dichloromethane‐acetone and dichloromethane‐ethanol. The obtained MALDI‐FTMS mass spectrum contains nine clusters of peaks in the m/z range of 420–2200, and the obtained APCI‐FTMS mass spectrum contains three clusters of peaks in the m/z range of 380–910. The peaks in the clusters correspond to the oxygenated derivatives of terpenoids differing by the number of C₁₅H₂₄ units. The clusters, in turn, are composed of subclusters differing by the number of oxygen atoms in the molecules. Thorough analysis and identification of the components (or groups of components) by their accurate m/z ratios was carried out, and molecular formulas (elemental compositions) of all major peaks in the MALDI‐FTMS and APCI‐FTMS spectra were identified (and groups of possible isomeric compounds were proposed). In the MALDI‐FTMS and APCI‐FTMS mass spectrum, besides the oxidized C₃₀, triterpenoids also peaks corresponding to C₂₉ and C₃₁ derivatives of triterpenoids (demethylated and methylated, correspondingly) were detected. MALDI and APCI are complementary ionization sources for the analysis of natural dammar resin. In the MALDI source, preferably polar (extensively oxidized) components of the resin are ionized (mostly as Na⁺ adducts), whereas in the APCI source, preferably nonpolar (hydrocarbon and slightly oxidized) compounds are ionized (by protonation). Either of the two ionization methods, when used alone, gives an incomplete picture of the dammar resin composition. Copyright © 2012 John Wiley & Sons, Ltd.     

A high‐sample‐throughput LC–GC method for mineral oil determination

The present investigation deals with a method improvement to increase data throughput and reduce solvent consumption for both saturated and aromatic mineral oil hydrocarbon determination using a coupled liquid–gas chromatographic system. The starting point of this work was the method proposed by Biedermann, Fiselier, and Grob in 2009. A total time and solvent reduction of 34 and 23%, respectively, was obtained by speeding up the GC run and reducing the LC‐reconditioning step. The band broadening, occurring in the LC column during stop‐flow in the multitransfer mode, was assessed by comparing the variances of the perylene peak width recorded in the stop‐flow and normal modes. Band broadening directly proportional to the stop time of the LC pumps was observed, however, it did not affect the analytical reliability. A series of real samples (paperboards and pasta) was analyzed obtaining comparable results using both the reference and proposed method, both in the normal and multitransfer modes.     

Compositional elucidation of heavy petroleum base oil by GC × GC‐EI/PI/CI/FI‐TOFMS

Comprehensive two‐dimensional gas chromatography (GC × GC) coupled to time‐of‐flight mass spectrometry is a powerful separation tool for complex petroleum product analysis. However, the most commonly used electron ionization (EI) technique often makes the identification of the majority of hydrocarbons impossible due to the exhaustive fragmentation and lack of molecular ion preservation, prompting the need of soft‐ionization energies. In this study, three different soft‐ionization techniques including photo ionization (PI), chemical ionization (CI), and field ionization (FI) were compared against EI to elucidate their relative capabilities to reveal different base oil hydrocarbon classes. Compared with EI (70 eV), PI (10.8 eV) retained significant molecular ion (M^+·) information for a large number of isomeric species including branched‐alkanes and saturated monocyclic hydrocarbons along with unique fragmentation patterns. However, for bicyclic/polycyclic naphthenic and aromatic compounds, EI played upper hand by retaining molecular as well as fragment ions to identify the species, whereas PI exhibited mainly molecular ion signals. On the other hand, CI revealed selectivity towards different base oil groups, particularly for steranes, sulfur‐containing thiophenes, and esters, yielding protonated molecular ions (M + H)⁺ for unsaturated and hydride abstracted ions (M‐H⁺) for saturated hydrocarbons. FI, as expected, generated intact molecular ions (M^+·) irrespective to the base oil chemical classes. It allowed elemental composition by TOFMS with a mass resolving power up to 8000 (FWHM) and a mass accuracy of 1 mDa, leading to the calculation of heteroatomic content, double bond equivalency, and carbon number of the compounds. The qualitative and quantitative results presented herein offer a unique perspective into the detailed comparison of different ionization techniques corresponding to several hydrocarbon classes.     

Separation of the mineral oil aromatic hydrocarbons of three and more aromatic rings from those of one or two aromatic rings

An analytical method was developed for the quantitation of the mineral oil aromatic hydrocarbons in cosmetic raw materials separating those of one or two aromatic rings from those of three and more aromatic rings. Normal phase high performance liquid chromatography was used with donor‐acceptor complex chromatography. The composition of both fractions and the quantities of respective compounds were determined by comprehensive two dimensional gas chromatography with time of flight mass spectrometry and by liquid chromatography coupled to gas chromatography with flame ionization detection.     

Electron‐induced dissociation (EID) for structure characterization of glycerophosphatidylcholine: determination of double‐bond positions and localization of acyl chains

Glycerophospholipids are a highly abundant and diverse collection of biologically relevant lipids, and distinction between isomeric and isobaric species is a fundamental aspect for confident identification. The ability to confidently assign a unique structure to a glycerophospholipid of interest is dependent on determining the number and location of the points of unsaturation and assignment of acyl chain position. The use of high‐energy electrons (>20 eV) to induce gas‐phase dissociation of intact precursor ions results in diagnostic product ions for localizing double‐bond positions and determining acyl chain assignment. We describe a high‐resolution, tandem mass spectrometry method for structure characterization of glycerophospholipids using electron‐induced dissociation (EID). Furthermore, the inclusion of nomenclature to systematically assign bond cleavage sites with acyl chain position and double‐bond location enables a uniform platform for lipid identification. The EID methodology detailed here combines novel application of an electron‐based dissociation technique with high‐resolution mass spectrometry that facilitates a new experimental approach for lipid biomarker discovery and validation. Copyright © 2015 John Wiley & Sons, Ltd.     

稠油中饱和烃复杂混合物成分解析及其意义

利用两根极性不同的毛细柱,在全二维气相色谱上分析辽河油田遭受严重生物降解形成的稠油饱和烃组分,可以将传统色谱分析时形成的“基线鼓包”即不可分辨的复杂混合物（Unresolved Complex Mixtures）分开．根据饱和烃全二维气相色谱谱图的族分离特点和瓦片效应,结合飞行时间质谱提供的质谱信息初步解析不可分辨的复杂混合物主要成分．发现常规色谱分析时形成的所谓“基线鼓包”是由成千上万、含量相对较低的不同取代基的环状化合物组成,这些化合物在一维色谱上以分子量递增的顺序排列,在二维色谱上以极性的差异或者环的多少排列．C24之前的第一组不可分辨的复杂混合物主要由环己烷为基本单元的单环、双环和三环烷烃类化合物组成,信噪比在100以上的化合物数量约为饱和烃总数量的75％,质量分数是饱和烃总量的80％以上,是饱和烃的主要组成部分．C24之后出现的第二组不可分辨的复杂混合物主要由四个环或者五个环为基本单元的化合物组成,信噪比在100以上的化合物数量约为饱和烃总数量的17％,质量分数是饱和烃总量的0．5％．对稠油中这些不可分辨的复杂混合物的解析有助于对其成因机理的认识和高效开采方案的制定．