电流变液体黏性变化趋势的试验研究

以微观试验和流变性能试验为手段，分别研究零电场下和在电场作用下的电流变液体黏性变化规律．研究结果表明：零电场下电流变液体的黏性与Krieger-Dougherty公式具有很好的拟合效果，其中逾渗临界值强依赖于悬浮液体中固体颗粒的性质并随工作温度变化．在电场作用下，电流变悬浮液体的黏度随剪切速率的变化规律分为3个阶段：即呈线性的启动段、非线性的幂定律模型流动段和宾汉模型流动段．研究结果为电流变效应工程应用提供依据．     

Effects of electrode morphology on the slit flow of an electrorheological fluid

In this work the effects of electrode morphology on the slit flow of an electrorheological (ER) fluid via laser Doppler anemometry (LDA) are studied. For this purpose, oblique and corrugated electrodes were used. Under a.c.-conditions the ER-effect with the oblique and corrugated electrodes is greater in comparison to the case of smooth electrodes at the same voltage and pressure drop. An average factor of 2.0 and 2.5 (in the range 1–5 kV) describes the increase in the ER-effect for the oblique and corrugated electrodes, respectively. This increase in ER-effect is accompanied by a decrease in electric current. Under d.c.-conditions the ER-effect with the oblique and corrugated electrodes is somewhat better than with the smooth electrodes but only at a very low field strength. Increasing the field strength leads to a decreased ER-effect (in comparison to the smooth electrodes). This decrease of the ER-effect is always accompanied by a decrease in electric current (d.c.-field).     

A microstructural investigation of the nonlinear response of electrorheological suspensions

In the preceding paper, Part 1, the transition from linear to nonlinear behavior for electrorheological (ER) suspensions under start-up of steady shear flow was found to first arise from the slight rearrangement of unstable structures. In this paper, we investigate the transition to nonlinear behavior for ER suspensions under oscillatory shear flow, focusing on the role of the rearrangement of unstable structures, and employing experimental and simulation results. Again, we find that nonlinear deformation first arises from these rearrangements, as opposed to the gross rearrangement or rupture of particulate chains. The Fourier transform of the simulated time-dependent shear stress is employed to quantify the dependence of the critical strain on the deformation frequency and electric field strength. The predicted behavior is consistent with experimental trends. Methods for verifying the predictions are discussed, as well as possible avenues for exploiting this information in improved operating strategies and improved ER fluids.     

On the behavior of fine mud suspensions

Flows of natural mud-water mixtures are of great interest for industrial and civil engineering. But there is still no general agreement about the methods for determining the main rheological characteristics of these systems. We propose here an accurate rheological study of some natural mud-water mixtures. We first discuss the possible effects of changing various parameters such as temperature, pH, electrolyte concentration, solid concentration, clay type. The behavior of these muds appears to be very sensitive to most of these parameters and to be hardly predictable from a knowledge of their components. Then, we show that a Herschel-Bulkley model fits very well steady flow experimental data for a very large range of shear rates. We also suggest physical explanations of this model in agreement with our observations of behavior changes when some parameters change. The yield stress value of this model provides a good estimation of real yield stress which is a key parameter for mixture behavior. These considerations are very useful to characterize, predict, and compare various mud flows.     

On the non-linear instability of fiber suspensions in a Poiseuille flow

The non-linear instability characteristics of fiber suspensions in a plane Poiseuille flow are investigated. The evolution equation of the perturbation amplitude analogous to Landau equation is formulated and solved numerically for different fiber parameters. It is found that the equilibrium amplitude decreases with the increase of the fiber aspect ratio and volume fraction, i.e. the addition of the fibers reduces the amplitude of the perturbation, and leads to the reduction of the flow instability. This phenomenon becomes significant for large volume concentration and aspect ratio. The mechanism of the reduction of the flow instability is also analyzed by taking into account of the modification of the mean flow and the energy transfer from the mean flow to the perturbation flow.     

Non-linear viscoelastic behavior of fumed silica suspensions

Suspensions of fumed silica exhibit a wide range of rheological properties depending on the nature and magnitude of the interparticle forces. In a non-polar fluid, the particles interact through hydrogen bonding and can form a three-dimensional network. The microstructure formation is responsible for the non-linear viscoelastic behavior of fumed silica suspensions, even at very small strain. These non-linear rheological properties have been studied in small amplitude oscillatory experiments as a function of particle size, surface treatment of particles, suspending medium polarity and solids concentration. The non-linear viscoelastic behavior is characterized by a non-sinusoidal waveform of the signal response. For suspensions in a non-polar fluid, both the elastic and the loss moduli are shown to be sensitive to the strain amplitude: the elastic modulus is decreasing with increasing strain whereas the loss moduli is initially increasing with strain. We have chosen to examine the dissipated energy which is clearly related to the breakup of the suspension structure. A comparison of model predictions and the experimental data shows the limitations of these models, recently proposed in the literature to describe the behavior of colloidal suspensions. Received: 9 March 1998 Accepted: 17 November 1998     

Stability analysis in spatial mode for channel flow of fiber suspensions

Different from previous temporal evolution assumption, the spatially growing mode was employed to analyze the linear stability for the channel flow of fiber suspensions. The stability equation applicable to fiber suspensions was established and solutions for a wide range of Reynolds number and angular frequency were given numerically . The results show that, the flow instability is governed by a parameter H which represents a ratio between the axial stretching resistance of fiber and the inertial force of the fluid. An increase of H leads to a raise of the critical Reynolds number, a decrease of corresponding wave number, a slowdown of the decreasing of phase velocity , a growth of the spatial attenuation rate and a diminishment of the peak value of disturbance velocity. Although the unstable region is reduced on the whole, long wave disturbances are susceptible to fibers.     

Modulus-switching viscoelasticity of electrorheological networks

To form an electrorheological network (ERN), semiconducting nanoparticles were embedded in a polymer that was cross-linked to restrict particle motion. The microstructure ranged from random to aligned, depending on the degree of field-induced particle alignment during chemical network formation. We investigated in detail the softness effects of the matrix, having a relatively low storage modulus, on the dynamic rheological behavior of the ERN and analyzed its anisotropy. The anisotropy of the microstructure was probed rheologically with the modes of small-amplitude oscillatory shear (loading perpendicular to the field direction) and compression (loading in the field direction). The storage shear modulus was found to be a function of the applied electric field, particle volume fraction, and the pre-alignment electric field strength during the cross-linking reaction of the matrix, which governs the thickness of particle columns and intercolumn distance. Nonlinear behavior at small strain (below 0.1%) was conspicuous; this nonlinear viscoelasticity was accompanied by only a limited deformation of ordered connectivity. Throughout this study, we fabricated the ERN with the highly controllable modulus-switching effect acting in a shear-mode operation. Managing this anisotropy of an ERN by the electrical and chemical process is important in the design of smart materials that will provide improved stability and mechanical strength compared with fluid-type electrorheological materials and faster response time compared with that of conventional charged polymer gel.     

Orientation distribution of fibers and rheological property in fiber suspensions flowing in a turbulent boundary layer

A model relating the translational and rotational transport of orientation distribution function （ODF） of fibers to the gradient of mean ODF and the dispersion coefficients is proposed to derive the mean equation for the ODE Then the ODF of fibers is predicted by numerically solving the mean equation for the ODF together with the equations of turbulent boundary layer flow. Finally the shear stress and first normal stress difference of fiber suspensions are obtained. The results, some of which agree with the available relevant experimental data, show that the most fibers tend to orient to the flow direction. The fiber aspect ratio and Reynolds number have significant and negligible effects on the orientation dis- tribution of fibers, respectively. The additional normal stress due to the presence of fibers is anisotropic. The shear stress of fiber suspension is larger than that of Newtonian solvent, and the first normal stress difference is much less than the shear stress. Both the additional shear stress and the first normal stress difference increase with increasing the fiber concentration and decreasing fiber aspect ratio.     

Layered model of electrorheological fluid under flow

We present a theoretical model of the behavior of a concentrated electrorheological fluid (ERF) which explicitly takes into account the effects of conductivity. The increase in shear viscosity under an electric field is due to a layered structure between the electrodes, made up of the remnants of particle chains adhering to the electrodes by electrostatic image forces, and a freely flowing liquid layer where all the shear flow is concentrated. This layered model can explain the variation of electric current with shear rate, as well as the rheological response of a dynamic yield stress proportional to the square of the applied electric field.     

Effects of anionic additives on the rheological behavior of aqueous calcium montmorillonite suspensions

Three different experimental measurements, namely, rheology, particle sizing, and x-ray diffraction (XRD), were used to study the effect of anionic additives on the properties of bentonite suspensions. The three additives were sodium carboxymethylcellulose, xanthan gum, and sodium dodecyl sulfate. Flow curves were obtained from shear stress–shear rate measurements, and the viscoelastic properties were determined from oscillatory and transient measurements. Mineralogical data were evaluated by XRD and the particle size analysis performed by light scattering technique. The presence of the surfactant modifies the face-to-face interactions and yields changes of the mixtures rheological behavior at low deformation rates. Polymers act by coating each clay particle and prevent their agglomeration. Therefore, the additives are responsible for the mechanisms of destructuration and structure reorganization as well as the mixtures viscous and viscoelastic behavior.     

Stability of some shear flows for concentrated suspensions

In this paper we investigate the stability of some viscometric flows for a concentrated suspension model which allows for the effects of shear-induced migration, including plane and circular Couette and Poiseulle flows, and unbounded and bounded torsional flows. In the bounded torsional flow, where its radial outer boundary is assumed frictionless, an exact closeform solution is given. With the exception of torsional flows, we find that a limit point for all the steady-state solutions can exist for certain range in the parameter values. In all cases, disturbances can persist for a long time, O (H ²/a ²), where H is a dimension of the flow field, and a is the particles' radius.     

Shear behaviour of biopolymer suspensions with spheroidal and cylindrical particles

The rheological behaviour of suspensions is influenced by many parameters, one of which is the particle shape. For rigid particle suspensions a number of studies demonstrate the effects of the particle aspect ratio. Indeed, fibres are widely used as rheology modifiers in different materials such as synthetic polymers. This work is concerned with testing the hypothesis that regularly shaped particles with aspect ratios larger than one that are made of gelled biopolymers could be used as rheology modifiers for biopolymer solutions. Biopolymers, and mixtures thereof are a widely used ingredient in foods and other products with structure functionality. Tailoring rheology modifiers by morphology offers an alternative to using different biopolymers. It is demonstrated how biopolymer suspensions with regular spheroidal, or cylindrical particle shapes can be produced by gelling the droplet phase of a liquid two phase biopolymer mixture in a shear field. Biopolymers were chosen such that gelation is initiated by cooling. Shear-cooling at constant stresses leads to the formation of ellipsoidal particles. Cylindrical particles can be generated by stepping up the shear stress prior to gelation, i.e., stretching the droplet phase into fibrils, and trapping the shape prior to break-up through gelation. Morphologies and steady shear rheological data for suspensions of the two biopolymers gellan and κ-carrageenan with an internal phase volume of 0.2 are reported. The influence of particle shape on relative viscosity is pronounced. At high shear stresses particle orientation leads to decreased viscosity with increasing particle aspect ratio. In the low shear region, higher aspect ratio suspensions show higher viscosities. Additionally, the material properties, including the interfacial tension, which influence the suspension morphology are reported. Received: 3 March 2000 Accepted: 22 August 2000     

Effect of poly(ethylene oxide) on the rheological behavior of silica suspensions

The steady-shear viscosity, dynamic viscoelasticity, and sedimentation behavior were measured for silica suspensions dispersed in aqueous solutions of poly(ethylene oxide) (PEO). For suspensions prepared with polymer solutions in which the transient network is developed by entanglements, the viscosity at a given shear rate decreases, shows a minimum, and then increases with increasing particle concentration. Because the suspensions are sterically stabilized under the conditions where the particle surfaces are fully covered with by a thick layer of adsorbed polymer, the viscosity decrease can be attributed to the reduction of network density in solution. But under the low coverage conditions, the particles are flocculated by bridging and this leads to a viscosity increase with shear-thinning profiles. The polymer chains with high molecular weights form flexible bridges between particles. The stress-dependent curve of storage modulus measured by a stress amplitude sweep shows an increase prior to a drastic drop due to structural breakdown. The increase in elastic responses may arise from the restoring forces of extended bridges with high deformability. The effect of PEO on the rheological behavior of silica suspensions can be explained by a combination of concentration reduction of polymer in solution and flocculation by bridging.     

A new constitutive model for fibre suspensions: flow past a sphere

A new phenomenological constitutive equation for homogeneous suspensions of macrosized fibres is proposed. In the model, the local averaged orientation of the fibres is represented by a director field, which evolves in time in a manner similar to the rotation of a prolate spheroid. The stress is linear in the strain rate, but the viscosity is a fourth-order tensor that is directly related to the director field. In the limit of low-volume fractions of fibres, the model reduces properly to the leading terms of the constitutive equation for dilute suspensions of spheroids. The model has three parameters: the aspect ratio R of the fibres, the volume fraction , and A, which plays the role of the maximum-volume fraction of the fibres. Experimental shear data are used to estimate the parameter A, and the resulting model is used in a boundary-element program to study the flow past a sphere placed at the centre line of a cylinder for the whole range of volume fractions from 0.01 to near maximum volume fraction. The agreement with experimental data from Milliken et al. [1] is good.     

Effect of matrix viscoelasticity on the electrorheological properties of particle suspensions

We have investigated the electrorheological properties of dispersions of semi-conducting particles in oils and elastomers. We focused on how the dynamic mechanical properties measured under oscillatory shearing change with the viscosity of the oil or the elasticity of the elastomer. The dependence on electric field and strain amplitude were also investigated. We found that the largest increment of the mechanical properties under electric fields was obtained when using oils of low viscosity and elastomers of low elasticity. The strain amplitude which produced the largest variation with electric field was found to be 0.1% for the elastomer systems, but significantly larger (1%) for the oil systems. These results are interpreted in terms of a model based on the competition between the dipole–dipole electrostatic interaction (which acts to maintain neighbouring particles together) and the shearing force due to the deformation of the matrix (which acts to separate the particles). We find that there are parallels between the electrorheological behaviour of particles dispersed in elastomers and the behaviour of particles dispersed in oils. These results should find application in the selection of suitable matrix materials for electrorheological suspensions.     

Stable and contact-free time stepping for dense rigid particle suspensions

We consider suspensions of rigid bodies in a two-dimensional viscous fluid. Even with high-fidelity numerical methods, unphysical contact between particles occurs because of spatial and temporal discretization errors. We extend a time stepping method that avoids overlap by imposing a minimum separation distance between all pairs of bodies. In its original form, the method discretizes interactions between different particles explicitly. Therefore, to avoid stiffness, a large minimum separation distance is used. In this paper, we introduce a new implicit time stepping method that is able to simulate dense suspensions with large time step sizes and a small minimum separation distance. The method is tested on various unbounded and bounded flows, and rheological properties of the resulting suspensions are computed.     

The effect of mixing particles of different size on the electrorheological response under steady shear flow

 The effect of mixing particles of different sizes on the electrorheological response of suspensions under steady shear flow was investigated. Two sizes, 15 μm and 50 μm, of monodisperse spherical sulfonated poly(styrene-co-divinylbenzene) particles were used. Several electrorheological fluids were made containing different proportions of small and large particles dispersed in silicone oil, but with constant overall particulate concentration. It was found that the mixed size system produced the highest electrorheological response under the shear rates used (10 s⁻¹ to 500 s⁻¹), which is the opposite trend to previous studies of bimodal systems with larger size ratios. Received: 21 December 2000 Accepted: 29 March 2001     

Constitutive equations for fiber suspensions in viscoelastic media

The kinetic theory of elastic dumbells with a friction factor that depends on the fiber orientation is used to obtain constitutive equations for fiber suspensions in a polymer matrix. We followed the approach of Fan (X.J. Fan, in P. Moldenaers and R. Keunings (Eds.), Theoretical and Applied Rheology, Proceedings XIth International Congress on Rheology, Brussels, Elsevier, Amsterdam, 1992, pp. 850–852), and derived equations for polymer solutions based on the FENE-P, FENE-CR, and Giesekus models. Start-up and steady-state free shear flows are studied to explore the effects of the fiber-polymer coupling as well as the fiber volume fraction. Predictions based on different types of closure approximations for the fourth-order fiber orientation tensor are also discussed.     

On the behaviour of gelled fibre suspensions in steady shear

The shear rheological properties of suspensions of gelled agar fibres in a low viscosity Newtonian matrix fluid were investigated. Two classes of fibres, low aspect ratio fibres and high aspect ratio fibres with an aspect ratio of the order of 10 and 100 respectively were included in the investigations. For all fibre phase volumes investigated, from as low as 0.01 upwards, the flow curves are characterised by an apparent yield stress followed by shear-thinning which was independent of the fibre aspect ratio. Based on our analysis of the flow curves, we conclude that the high aspect ratio fibres behave like flexible threads in contrast to the low aspect ratio fibres whose high shear relative viscosity is successfully described by a relation for long rigid rods. These findings are supported by flow visualisation using an optical shearing stage coupled to a light microscope.