Preparation of aminylferrocene/nanogold modified glassy carbon electrode and its electrocatalysis on dopamine

Aminylferrocene(FcAI)-Nanogold(NG) modified glassy carbon electrode (FcAI/NG/GCE) was prepared by the Au-N bond between Au and FcAI. Electrochemical impedance spectroscopy (EIS) was employed to study the surface of the modified electrode. The electrochemical behavior of dopamine (DA) on the modified electrode was investigated and it was found that the modified electrode had an obvious electrocatalytic effect on DA. Compared with a bare GCE, the modified electrode exhibited an apparent shift of the oxidation peak potential in the negative potential direction and a marked enhancement in the current response for DA. We investigated the determination of DA on the modified electrode by differential pulse voltammetry (DPV). Linear calibration curve was obtained in the range of 7.0 x 10(-7) mol/L to 6x10(-4) mol/L of DA in 0.1 mol/L phosphate buffer solution (pH = 7.0) with a correlation coefficient of 0.9989. The detection limit (S/N = 3) of DA was estimated to be 1.0 x 10(-7) mol/L. Especially, by using the modified electrode, we can separate the oxidation peaks of ascorbic acid (AA) and DA in the PBS and it was satisfactory for the determination of DA with the interference of AA.     

Direct electrochemistry and electrocatalysis of hemoglobin in gelatine film modified glassy carbon electrode

Direct electrochemical and electrocatalytic behavior of hemoglobin (Hb) immobilized on glass carbon electrode (GCE) containing gelatine (Gel) films was investigated. The characteristics of Hb/Gel film modified GC electrode were performed by using SEM microscopy, UV-vis spectroscopy and electrochemical methods. The immobilized Hb showed a couple of quasi-reversible redox peak with a formal potential of −0.38 V (versus SCE) in 0.1 M pH 7.0 PBS. The formal potential changed linearly from pH 4.03 to 8.41 with a slope value of −52.0 mV pH⁻¹, which suggested that a proton transfer was accompanied with each electron transfer (ET) in the electrochemical reaction. The Hb/gelatine/GCE displayed a rapid amperometric response to the reduction of H₂O₂ and nitrite.     

聚邻苯二胺修饰玻碳电极的制备及电催化性能

在磷酸盐缓冲溶液中研究了邻苯二胺在玻碳电极表面的聚合过程,探讨了各氧化还原峰的变化机理,用扫描电镜表征了聚邻苯二胺膜的形态结构。发现制备的聚邻苯二胺膜修饰电极对H2O2有显著的电催化还原特性,线性回归方程为:Δipa(μA)=-1.63 1.07cH2O2(mmol.L-1)(R=0.9947,n=19),线性范围为:5.89×10-2mmol.L-1~44.4 mmol.L-1,检出限为:0.02 mmol.L-1(3S/k),这对与产生H2O2的氧化酶相结合制备出响应各种底物的电化学生物传感器非常重要。考察了制备条件对膜电极电催化还原活性的影响,发现只有在弱酸条件下制备的膜电极才有较高的电催化活性。探讨了影响膜电极电催化还原灵敏度的因素,并考察了膜电极的稳定性。     

Myoglobin on multi-walled carbon nanotubes modified electrode: direct electrochemistry and electrocatalysis

Electrochemical behavior of myoglobin (Myb) incorporated on multi-walled carbon nanotubes (MWNTs) modified GC electrode is investigated by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The results indicate that Myb can be strongly adsorbed on the surface of the MWNT-modified electrode to form an approximate monolayer film. MWNTs can greatly promote the redox of horse heart Myb, on which a pair of well-defined and nearly reversible CV peaks for Myb Fe(III)/Fe(II) redox couple were obtained in pH 7.0 buffers. The formal potential of Myb on MWNT modified electrode shifts linearly with pH with a slope of −56.4 mV/pH, showing that the electron transfer is accompanied by single proton transportation. The high efficiency of the Myb/MWNT modified electrode towards the catalytic electro-reduction of nitric oxide has been observed. Potential application of Myb/MWNT modified electrode as biosensors to monitor NO is proposed.     

磺胺在碳纳米管修饰玻碳电极上的电化学行为

磺胺类抗菌药是一类允许在饲料中添加的兽用广谱抗菌药.它被广泛用于治疗家畜呼吸道、消化道细菌感染、猪萎缩性鼻炎、禽霍乱、伤寒等疾病[1].停药期用药或用药不当将导致动物食品中抗菌药残留超标.人们长期食用含磺胺类抗菌药残留超标的动物产品,将导致肝肾损伤和体内耐药菌株产生,危害到人们的身体健康和疾病治疗.     

Direct electrochemistry and electrocatalysis of hemoglobin on undoped nanocrystalline diamond modified glassy carbon electrode

Direct electrochemistry of hemoglobin (Hb) was observed at glassy carbon electrode (GCE) modified with undoped nanocrystalline diamond (UND) and Hb multilayer films via layer-by-layer assembly. UV-VIS absorbance spectroscopy, electrochemical impedance spectroscopy and cyclic voltammograms were employed to characterize the film. The results showed that the UND had the effect of enhancing the electron transfer between Hb and the electrode surface. Hb in the multilayer films maintained its bioactivity and structure. It also exhibited a good catalytic activity towards the reduction of H(2)O(2). The reciprocal of catalytic current showed a linear dependence on the reciprocal of H(2)O(2) concentration ranging from 0.5 microM to 0.25 mM with a detection limit of 0.4 microM. The apparent Michaelis-Menten constant was estimated to be 0.019 mM.     

Electrocatalytic oxidation and sensitive determination of l-cysteine at a poly(aminoquinone)-carbon nanotubes hybrid film modified glassy carbon electrode

A matrix removal procedure has been developed for the determination of trace elements, including As, Cd, Co, Cr, Cu, Hg, Ni, Pb, Sb, Se, Sn, Tl, Zn and V, in siliceous materials by inductively coupled plasma mass spectrometry (ICP-MS). Soil and sediment samples were dissolved in a mixture of HNO₃ and HF in sealed vessels by using a microwave oven. Silicon matrix in the solutions was precipitated as sparingly soluble sodium fluorosilicate (Na₂SiF₆) by adding 0.5 mL of 300 mg mL⁻¹ NaCl solution. Simultaneous precipitation of sodium and silicon was achieved in highly acidic solutions containing 30–40% (v/v) HNO₃. A mixture of methanol and nitric acid afforded back-extraction of the trace elements without significant dissolution of the Na₂SiF₆. Samples were analyzed by ICP-MS for trace elements and residual silicon. Calibration was made by aqueous multi-element standard solutions. Up to 95% of the silicon was successfully removed yielding solutions suitable for introduction to ICP-MS. The method was validated by analysis of two NIST certified reference materials; SRM 2711 (Montana Soil) and SRM 2704 (Buffalo River Sediment). Accurate results were obtained for all elements, including those for As, Hg and Se that suffer from losses due to the presence of their volatile species when silicon was converted to volatile SiF₄ via heat-assisted evaporation to dryness. The recoveries from the SRM samples varied between 80% (Cr) and 109% (Hg). No significant interferences were observed from molecular ions of chloride and residual sodium on ⁷⁵As, ⁶³Cu, ⁶⁰Ni, ⁷⁷Se and ⁵¹V. Correspondence: Zikri Arslan, Department of Chemistry, Jackson State University, Jackson, MS 39217, USA     

Silicomolybdate doped polypyrrole film modified glassy carbon electrode for electrocatalytic reduction of Cr(VI)

Electrically conducting polypyrrole (PPy) film doped with silicomolybdate (SiMo₁₂ or SiMo₁₂) was synthesized by electrochemical polymerization. The synthesized film is capable of fast charge propagation during redox reactions in strong acid medium 0.2 M H₂SO₄ solution. Electrochemical quartz crystal microbalance was used to study the mechanism and amount of SiMo₁₂ doped in the PPy matrix. The modified electrode surface was characterized by using atomic force microscope technique, and it was found that the minimum and maximum globule size were estimated to be in the range of 50–200 nm. The thickness of film was measured to be approximately 30 ± 10 nm. The modified electrode shows electrocatalytic activity towards reduction of Cr(VI) and periodate. The rate constant and optimal film thickness were determined for electrocatalytic reduction of Cr(VI) by using rotating disc electrode experiment. Analytical characterization of the SiMo₁₂ doped PPy film modified electrode was demonstrated by flow injection analysis (FIA) technique and shows good stability for 16 continuous injections for Cr(VI) reduction with RSD of 1.6%.     

Direct electrochemistry and electrocatalysis with hemoglobin in water-soluble quantum dots film on glassy carbon electrode

The direct electrochemistry of hemoglobin can be performed by immobilizing hemoglobin in a water-soluble quantum dots (CdSe-ZnS) film on glassy carbon electrode.     

Electrochemical reduction and voltammetric determination of metronidazole at a nanomaterial thin film coated glassy carbon electrode

Simple and sensitive electrochemical method for the determination of metronidazole, based on a nanostructured film coated glassy carbon electrode (GCE), is described. Multi-walled carbon nanotubes (MWNT) was dispersed into water in the presence of a hydrophobic surfactant to give very stable and homogeneous MWNT suspension, and a MWNT-film coated GCE was achieved via evaporating solvent. Metronidazole yields a well-defined reduction peak whose potential is −0.71 V at the MWNT-film coated GCE in pH 9.0 Britton-Robinson buffer. Compared with bare GCE, the MWNT-film modified GCE significantly enhances the reduction peak current of metronidazole. All the experimental parameters were optimized for the determination of metronidazole. The detection limit is 6×10⁻⁹ mol/l at 2 min accumulation. This method has been successfully used to determine metronidazole in the drugs. Furthermore, results obtained by the proposed method have been compared with spectrophotometric method.     

二苯氨基碳酰肼在多壁碳纳米管修饰电极上的电催化氧化及电化学动力学研究

肼及其衍生物被广泛应用于医药,农药,水处理,军事,航天,光稳定剂以及化工生产助剂等诸多领域。因此对肼及其衍生物的研究有着极其重要的意义。二苯氨基碳酰肼(二苯氨基脲,又名二苯卡巴肼,D iphenyl Carbazide,DPC)广泛用于重金属离子的检测分析[1-4]。但是,目前关于DPC的电化学     

苦参碱在多壁碳纳米管修饰玻碳电极上的电催化氧化及其电分析方法

研究了苦参碱(Matrine, MT) 在多壁碳纳米管修饰玻碳电极(MWCNT/GCE)上的电化学行为. 与GCE相比, MT在MWCNT/GCE上峰电位负移120 mV, 峰电流增大约2.5倍, 表明MWCNT/GCE对MT的电化学氧化具有良好的催化作用. 同时测定并计算了MT在MWCNT/GCE上的电极过程动力学参数: 电子转移系数α、电极反应速率常数ks、扩散系数D. 运用差分脉冲伏安法对苦参碱样品含量进行测定, 相对标准偏差为0.12%～2.9%, 加标回收率为98.4%～99.0%. 该方法可用于MT的电化学定量测定.     

羟胺在碳纳米管修饰玻碳电极上的电催化还原及电化学动力学性质研究

研究了羟胺在碳纳米管修饰玻碳电极(CNT/GC)上的电化学行为。研究结果表明,碳纳米管对羟胺的电化学行为有良好的电催化作用,在-0.62 V有一还原峰,是羟胺获得2个电子还原为铵所形成,同时测定了该电化学过程的动力学参数:电子转移数n为2,电子转移系数α为0.287,电极反应速率常数k为1.35×10-3cm/s。     

Nafion-graphene composite film modified glassy carbon electrode for voltammetric determination of p-aminophenol

A Nafion-graphene (Nafion-GR) nanocomposite film modified glassy carbon electrode was fabricated by a simple drop-casting method, and used in the electrochemical detection of p-aminophenol (4-AP). Owing to the large surface area, good conductivity of GR and good affinity of Nafion, the sensor exhibited excellent electrocatalytic activity for the oxidation of 4-AP. The electrochemical behaviors of 4-AP on Nafion/GR film modified glassy carbon electrodes were investigated by cyclic voltammetry and differential pulse voltammetry. A calibration curve is constructed in the same matrix, urine, as the unknown samples to be analyzed. The Nafion-GR film modified electrode was linearly dependent on the 4-AP concentration and the linear analytical curve was obtained in the ranges of 0.5–200 μM with differential pulse voltammetry (DPV) and the detection limit was 0.051 μM. The Nafion-graphene nanocomposite modified electrode exhibited good reusability than pure graphene modified GCE. This procedure can be used for the determination of p-aminophenol in the presence of its degradation products and paracetamol. Finally, the proposed method was successfully used to determine p-aminophenol in local tap water samples in urine samples and pharmaceutical preparations.     

氢氧化镍薄膜修饰玻碳电极的制备及其对L-赖氨酸氧化的电催化活性

采用恒电位沉积方法将氢氧化镍沉积到玻碳电极表面,得到稳定性高、催化活性好的氢氧化镍薄膜修饰玻碳电极;分析了影响薄膜形成过程的关键因素,确定了最佳薄膜制备方案;与此同时,将薄膜修饰玻碳电极用于生物样品L-赖氨酸的氧化测定,并探讨了其催化作用机理.结果表明,所制备的氢氧化镍薄膜修饰玻碳电极表面发生电化学反应[Ni(OH)2→NiOOH],从而促进电极表面的电子转移,实现对L-赖氨酸的电催化作用.当L-赖氨酸的浓度在1.0×10-4～4.0×10-7 mol/L范围内时,相应氧化峰电流与浓度呈线性关系,检出限达4.0×10-7 mol/L;据此可方便地制备稳定性好且灵敏度高的电流型传感器.     

Biosensor based on a glassy carbon electrode modified with tyrosinase immmobilized on multiwalled carbon nanotubes

We describe a biosensor for phenolic compounds that is based on a glassy carbon electrode modified with tyrosinase immobilized on multiwalled carbon nanotubes (MWNTs). The MWNTs possess excellent inherent electrical conductivity which enhances the electron transfer rate and results in good electrochemical catalytic activity towards the reduction of benzoquinone produced by enzymatic reaction. The biosensor was characterized by cyclic voltammetry, and the experimental conditions were optimized. The cathodíc current is linearly related to the concentration of the phenols between 0.4???M and 10???M, and the detection limit is 0.2???M. The method was applied to the determination of phenol in water samples.

Electrochemical behaviors of ofloxacin and its voltammetric determination at carbon nanotubes film modified electrode

A multi-wall carbon nanotubes (MWNTs)-Nafion film-coated glassy carbon electrode (GCE) was fabricated and the electrochemical behavior of ofloxacin on the MWNTs-Nafion film-coated GCE were investigated by cyclic voltammetry (CV), linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). The oxidation peak current of ofloxacin increased significantly on the MWNTs-Nafion film modified GCE compared with that using a bare GCE. This nano-structured film electrode exhibited excellent enhancement effects on the electrochemical oxidation of ofloxacin. A well-defined oxidation peak attributed to ofloxacin was observed at 0.97 V and was applied to the determination of ofloxacin. The oxidation peak current was proportional to ofloxacin concentration in the ranges 1.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol/L and 1.0 × 10⁻⁶ to 2.0 × 10⁻⁵ mol/L. A detection limit of 8.0 × 10⁻⁹ mol/L was obtained for 400 s accumulation at open circuit (S/N = 3). This method for the detection of ofloxacin in human urine was satisfactory. __________ Translated from Chinese Journal of Applied Chemistry, 2007, 24(5): 540–545 [译自: 应用化学]     

苯甲酰肼在多壁碳纳米管修饰玻碳电极上的电催化氧化及其电化学动力学性质

研究了苯甲酰肼(BH)在MWCNT/GCE上的电化学行为。实验结果表明,BH在GCE上的直接电化学氧化十分迟缓,无氧化峰出现,但在MWCNT/GCE上BH在0.20 V处出现了一个不可逆氧化峰,且峰电流大幅度增大,表明MWCNT/GCE对BH电化学氧化具有良好的催化作用。同时用计时库仑法(Chro-nocoulometry,CC)和计时电流法(Chronoamperometry,CA)测定了电极过程动力学参数:扩散系数D=8.73×10-5cm2.s-1,电子转移系数α=0.85,电极反应速率常数kf=1.45×10-3s-1。稳态电流-时间实验结果表明,电流响应信号随其浓度成比例增长,响应时间小于6 s,最低响应浓度为1×10-6mol/L。该方法可用于BH电化学定量测定。